My friend decided to use the EZ-Unlock app(link below) that unlocks the bootloader for the verizon galaxy s3 on my i747 and well it is now a brick, is there anything i can do to fix this without a JTAG?
omeadsthename said:
My friend decided to use the EZ-Unlock app(link below) that unlocks the bootloader for the verizon galaxy s3 on my i747 and well it is now a brick, is there anything i can do to fix this without a JTAG?
Click to expand...
Click to collapse
yes, take him outside and beat the crap out of him. Then take his money and go get a new phone.
Other than that, I don't know.
Can you access download mode or recovery?
jack man said:
yes, take him outside and beat the crap out of him. Then take his money and go get a new phone.
Other than that, I don't know.
Can you access download mode or recovery?
Click to expand...
Click to collapse
No I cannot, my friend(parklane79) and I actually found a method, it seems promising but i need to try it out first.
im not afforded the link rights yet but the title is "Fixing a bootloader-bricked Galaxy S3 using an SD card (Qualcomm SGS3 variants)" and a more simpler guide for n00bs(although not a complete n00b been doing this for a few years now :good: ) like myself, "[GUIDE]Unbrick a Hard Bricked SPRINT Galaxy S3 (Without JTAG)" but for the second guide you need to grab the i747 debrick.img off the first page of the first guide.
omeadsthename said:
No I cannot, my friend(parklane79) and I actually found a method, it seems promising but i need to try it out first.
im not afforded the link rights yet but the title is "Fixing a bootloader-bricked Galaxy S3 using an SD card (Qualcomm SGS3 variants)" and a more simpler guide for n00bs(although not a complete n00b been doing this for a few years now :good: ) like myself, "[GUIDE]Unbrick a Hard Bricked SPRINT Galaxy S3 (Without JTAG)" but for the second guide you need to grab the i747 debrick.img off the first page of the first guide.
Click to expand...
Click to collapse
Yea tried with a class 10 16g micro sd like a million times and it wont work.and i think its because i dont have the 4.4.2 img if some one could help me out by uploading it. u et the img via busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70
So the phone won't power on at all? Can't get into download or recovery?
are you %100 certain it's the AT&T 4.3 debrick.img? did you put it on the SD card using win32diskimager?
audit13 said:
So the phone won't power on at all? Can't get into download or recovery?
Click to expand...
Click to collapse
The phone won't even vibrate. Wish i could get to DL/Recovery mode. :/
yowski said:
are you %100 certain it's the AT&T 4.3 debrick.img? did you put it on the SD card using win32diskimager?
Click to expand...
Click to collapse
im 100% sure. the issue is tho that i was on 4.4.2 and dont know it an i747(AT&T) 4.3 debrick.img has the same handshake/protocol whatever you want to call it as a 4.4.2 debrick.img I tried it out tho anyways. but in short yes im 100% sure it was a 4.3 debrick img. And yes I did use win32diskimager. I tried once on linux mint but i believe the file corrupted so i just ended up using win32DM. I mean they are supposed to do the same thing, if im not mistaken
omeadsthename said:
The phone won't even vibrate. Wish i could get to DL/Recovery mode. :/
im 100% sure. the issue is tho that i was on 4.4.2 and dont know it an i747(AT&T) 4.3 debrick.img has the same handshake/protocol whatever you want to call it as a 4.4.2 debrick.img I tried it out tho anyways. but in short yes im 100% sure it was a 4.3 debrick img. And yes I did use win32diskimager. I tried once on linux mint but i believe the file corrupted so i just ended up using win32DM. I mean they are supposed to do the same thing, if im not mistaken
Click to expand...
Click to collapse
when you plug it into the computer does anything come up? also, when you plug it in with no battery do you get a red LED?
yowski said:
when you plug it into the computer does anything come up? also, when you plug it in with no battery do you get a red LED?
Click to expand...
Click to collapse
Yes my comp tries to install that one qualcomm driver. and when i plug in without battery a red LED comes on.
omeadsthename said:
Yes my comp tries to install that one qualcomm driver. and when i plug in without battery a red LED comes on.
Click to expand...
Click to collapse
Then you should be able to use a debrick.img. are you using an sd card the same size as your phone's internal memory? if you had it on 4.4.2 then you might need a debrick.img from someone with the same phone on the same network running 4.4.2?
yowski said:
Then you should be able to use a debrick.img. are you using an sd card the same size as your phone's internal memory? if you had it on 4.4.2 then you might need a debrick.img from someone with the same phone on the same network running 4.4.2?
Click to expand...
Click to collapse
yes i am using same size card. and i have been asking all over for a 4.4.2 debrick img but no one has uploaded.
omeadsthename said:
yes i am using same size card. and i have been asking all over for a 4.4.2 debrick img but no one has uploaded.
Click to expand...
Click to collapse
sounds like you're stuck until you get that .img file. If you know someone with the same phone you could maybe get them to install 4.4.2 and get the file from them? otherwise keep asking around or wait until 4.4.2 is released for the s3, which might take a while.
yowski said:
sounds like you're stuck until you get that .img file. If you know someone with the same phone you could maybe get them to install 4.4.2 and get the file from them? otherwise keep asking around or wait until 4.4.2 is released for the s3, which might take a while.
Click to expand...
Click to collapse
Unfortunately kids at my high school are afraid of rooting, so xda is basically my only bet. Im just surprised that some sr member hasnt added a debrick img to their threads. I mean its 4.4 and this is android central!
omeadsthename said:
yes i am using same size card. and i have been asking all over for a 4.4.2 debrick img but no one has uploaded.
Click to expand...
Click to collapse
i would help you out but my S3 is currently hard bricked on stock 4.3 and im sending it back to the insurance company once my S4 arrives tomorrow.
yowski said:
i would help you out but my S3 is currently hard bricked on stock 4.3 and im sending it back to the insurance company once my S4 arrives tomorrow.
Click to expand...
Click to collapse
Cant they find out that you are root and hard bricked? like doesnt that void warranty. and if its a 4.3 h brick cant u just use the sd method?
omeadsthename said:
yes i am using same size card. and i have been asking all over for a 4.4.2 debrick img but no one has uploaded.
Click to expand...
Click to collapse
I did, it was on CM 10.2 when i had flashed improper bootloaders and bricked it. I used the sd card to install 4.3, unroot+ reset flash counter then took it out so it went back to bricked. My only fear is that they may some how get it into download mode instead of just replacing the board and see the warranty bit: 1 which isnt able to be reset as it is an e-fuse which is blown when you install firmware without knox.
yowski said:
I did, it was on CM 10.2 when i had flashed improper bootloaders and bricked it. I used the sd card to install 4.3, unroot+ reset flash counter then took it out so it went back to bricked. My only fear is that they may some how get it into download mode instead of just replacing the board and see the warranty bit: 1 which isnt able to be reset as it is an e-fuse which is blown when you install firmware without knox.
Click to expand...
Click to collapse
Are you using the samsung warranty of AT&T? And also if the sd card is working for u cant you just use odin to flash? Or does the sd card not fix any bootloader issues?
omeadsthename said:
Are you using the samsung warranty of AT&T? And also if the sd card is working for u cant you just use odin to flash? Or does the sd card not fix any bootloader issues?
Click to expand...
Click to collapse
im sending in it through bell mobility. it was a replacement phone that i paid the $150 deductable on and has a 90 warranty. I said it was having issues/defective so they sent an s4 as free replacement on the 90 day. I prefer it to be bricked to fit the defective description as well as to decrease the chances of them finding out i had messed with it, the only real sign being "warranty bit: 1" in red on the download screen. I did use odin to flash the current 4.3 stock that it has right now, and i might be able to get it to boot without the card if i flash the bootloaders some more despite having done it twice and the card still being required. Like i said though, i prefer it hard bricked and i've erased every sign other than warranty bit: 1 that i messed with it by installing stock, unrooting, and resetting flash counter.
yowski said:
im sending in it through bell mobility. it was a replacement phone that i paid the $150 deductable on and has a 90 warranty. I said it was having issues/defective so they sent an s4 as free replacement on the 90 day. I prefer it to be bricked to fit the defective description as well as to decrease the chances of them finding out i had messed with it, the only real sign being "warranty bit: 1" in red on the download screen. I did use odin to flash the current 4.3 stock that it has right now, and i might be able to get it to boot without the card if i flash the bootloaders some more despite having done it twice and the card still being required. Like i said though, i prefer it hard bricked and i've erased every sign other than warranty bit: 1 that i messed with it by installing stock, unrooting, and resetting flash counter.
Click to expand...
Click to collapse
hmm i wish i could do that to my phone too. i mean, i dont even know how i would unroot without getting my phone on. but if im this hard bricked they probs cant tell anyways. im guessing?
uz unlock HARD BRICKING S3'S
omeadsthename said:
My friend decided to use the EZ-Unlock app(link below) that unlocks the bootloader for the verizon galaxy s3 on my i747 and well it is now a brick, is there anything i can do to fix this without a JTAG?
Click to expand...
Click to collapse
I DID THE SAME THING ! but i used debrick (i535 vzw 4.3 ) and it pattially worked at least it will recovery and odin but i think it needs to be the 40 mbps type card the black micro would not work for me , then i flashed the wrong recovery and am starting all over but the debrick still getting me into odin thats ware you will sideload the right recovery and firmware ,rom what ever hope ( i even paid for cdma work shop and it aint did jack ) debrick then odin sideload look it up thats the best i got
Related
I am now owner of what may very well be a Hard Bricked Samsung Galaxy S3 with the inability to reach Download Mode and computer not recognizing my handheld. It ll happen't as I unlocked my bootloader to go in fastboot mode, it was then, all over. But of course as desperate as it may look like I've done some researches on Google and some people with different models managed to have some magic done in a situation like mine, but since I didn't own the same device the solutions were of no avail for me. So my question is, is there any sort of trickery to help me come out of this misery? Such as force installing new QHSUSB_DLOAD specifically for a Samsung Galaxy S3 or some battery related magic that could help me reach Download Mode where I could flash a stock rom back in and get back to normal? Any help would be much appreciated.
this just happened to me as well today, not to happy, my heart sank in, did u find any solutions as far as fixing this qhusb thing?
AFAIK there is no fix, same deal on all phones with the same SoC, like the one x. I could be way wrong though and I hope I am. Hope you guys get up and running soon.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
http://forum.xda-developers.com/showthread.php?t=1522351
these guys were able to fix the QHSUSB problem, i just need these samsung s3 files like they have for the sensation xe only thing is i dont kno where to get them. ;/
Sent it under warranty hoping for the best.
Bibiquadium said:
Sent it under warranty hoping for the best.
Click to expand...
Click to collapse
Most likely they will say that you voided your warranty so you may have to take it in to a JTAG service.
Bibiquadium said:
Sent it under warranty hoping for the best.
Click to expand...
Click to collapse
Any update on this? My phone did this to me last night when updating CWM. I'm about to go to Radio Shack to buy some resisters to see if I can force download mode, like on Captivates.
EDIT: Even though this video (http://www.youtube.com/watch?v=TrZUrE5Nqj0) shows that the Jig works with the GS3, I was not successful in putting it into download mode. I was able to with my captivate, just to make sure I was on the correct pins.
Hopefully the AT&T store will just swap it out and leave it at that, since I pay for insurance...I don't want to have to send it away to mobiletechvideos.com for JTAG repair, but will if necessary.
Bibiquadium said:
I am now owner of what may very well be a Hard Bricked Samsung Galaxy S3 with the inability to reach Download Mode and computer not recognizing my handheld. It ll happen't as I unlocked my bootloader to go in fastboot mode, it was then, all over. But of course as desperate as it may look like I've done some researches on Google and some people with different models managed to have some magic done in a situation like mine, but since I didn't own the same device the solutions were of no avail for me. So my question is, is there any sort of trickery to help me come out of this misery? Such as force installing new QHSUSB_DLOAD specifically for a Samsung Galaxy S3 or some battery related magic that could help me reach Download Mode where I could flash a stock rom back in and get back to normal? Any help would be much appreciated.
Click to expand...
Click to collapse
You can look all you want for a solution, there is NOT one for this problem, other than find a jtag service. Period!
---------- Post added at 10:20 AM ---------- Previous post was at 10:12 AM ----------
DjRevler said:
http://forum.xda-developers.com/showthread.php?t=1522351
these guys were able to fix the QHSUSB problem, i just need these samsung s3 files like they have for the sensation xe only thing is i dont kno where to get them. ;/
Click to expand...
Click to collapse
Wow, this is a complete waste of time. This will not work with SG3
Talking about "waist of time" you are in the wrong forum, the att sgs3 doesn't have locked bootloader (this is the att/bell/Rogers forum) Go to the Verizon sgs3 forum...
Sent from my SGH-I747M using Tapatalk
TRusselo said:
Talking about "waist of time" you are in the wrong forum, the att sgs3 doesn't have locked bootloader (this is the att/bell/Rogers forum) Go to the Verizon sgs3 forum...
Sent from my SGH-I747M using Tapatalk
Click to expand...
Click to collapse
Regardless of where the phone came from the end result is still the same... you guys are hard bricked. The only available solutions to you atm (and trust me on this I hard bricked mine aswell) is
A - Send your phone in for warrenty/insurance, dont worry about everyone saying you cant because of voided warrenty... your bootloader is screwed and they wouldnt be able to tell anything about rooting/cwm etc.
B - if warrenty/insurance is unavailable to you then your only other options are to send it to samsung to get it repaired on your own dime. Or save yourself a bit of money and send it for jtag repair which is what I did. If you live in the states the guy can have your phone back in your hands usually within 4-5 business days.
hi there
i have an SDcard of 4GB i tried on 4 S3 i747M hard bricked phones its worked ....this card let them alive to download mode by pressing volume down key +home key + power. i want to share this image but when ever i connect this card to my PC (windows) its shows (need to format your card)
is there any software so i can make image and share...to help those who hard-bricked their phones.
regards
fallenkirmit said:
Regardless of where the phone came from the end result is still the same... you guys are hard bricked. The only available solutions to you atm (and trust me on this I hard bricked mine aswell) is
A - Send your phone in for warrenty/insurance, dont worry about everyone saying you cant because of voided warrenty... your bootloader is screwed and they wouldnt be able to tell anything about rooting/cwm etc.
B - if warrenty/insurance is unavailable to you then your only other options are to send it to samsung to get it repaired on your own dime. Or save yourself a bit of money and send it for jtag repair which is what I did. If you live in the states the guy can have your phone back in your hands usually within 4-5 business days.
Click to expand...
Click to collapse
I reject your reality, and substitute my own! Ah, anyway.. any updates on this? Its been a year or so.. I have the sprint s3, but i believe it had an insecure boot image flashed to it. The emmc boot method has failed me thus far. Not sure if it's because mine is a 32gb and the debrick files for for 16gb '(which shouldn't matter), if the board for my 32gb is affected by a brick bug, or what.. The qpst tool just seems like it's the perfect tool to fix a bad bootloader on any qualcomm phone, but all the guides I've found are for other phones still. I accidentally dd'd an image of my EFS partition to the sbl2 partition. I looked up the international s3 table by mistake
---------- Post added at 06:45 PM ---------- Previous post was at 06:39 PM ----------
rasgula said:
hi there
i have an SDcard of 4GB i tried on 4 S3 i747M hard bricked phones its worked ....this card let them alive to download mode by pressing volume down key +home key + power. i want to share this image but when ever i connect this card to my PC (windows) its shows (need to format your card)
is there any software so i can make image and share...to help those who hard-bricked their phones.
regards
Click to expand...
Click to collapse
Yes. Download a live linux distro, like knopix or such. Any linux distribution will work, really. Then in a terminal you would do something like
Code:
sudo dd if=/dev/sdX of=debrick-image.img
Where the "X" in "sdX" corresponds to the sdcard you want to copy. After you insert the card, in a terminal do:
Code:
dmesg | tail
and you should be able to see that it is sdb, sdc, sdd, etc. Google the usage of "dd" if you need more info.
Thanks for info i'll try this today
Regards
Sent from my C6506 using Tapatalk
rasgula said:
Thanks for info i'll try this today
Regards
Sent from my C6506 using Tapatalk
Click to expand...
Click to collapse
did you ever get that image? i could really use it right now... :crying:
johneightyone said:
did you ever get that image? i could really use it right now... :crying:
Click to expand...
Click to collapse
yes ....i have this image now on 3 sd cards. works fine for me...but image size is too large, about 3.7 GB.
regards
SGH-I747 (4.1.2 i747's please)/ SGH-i747m( If you have a official 4.3 i747m, please post a debrick.img) only:
Hi, I recently hard bricked my phone into QHSUSB DLOAD and I am going to attempt repairing it through the SD Card boot method.
http://forum.xda-developers.com/editpost.php?do=editpost&p=47431259
I need a debrick.img to flash to the SD card in a Linux OS.
I would have gotten it myself but my phone is obviously dead. I found one before on XDA, but it did not work on my device and it gave me an error in the Linux terminal when it should not have.
-snip-
The end of the 3rd boot-loader stage in mmcblk0 is at 77.3 megabytes. If you are going to help out using your device, try to refrain from uploading an image with a different ROM other than root.
Code:
dd if=/dev/block/mmcblk0 of=/sdcard/backup.img bs=2m count=81054925
The count is the amount of bytes. I am not sure if it is meant to be 1000 bytes=kilobyte or 1024 bytes=kilobyte. The count above is for 1024.
I need someone to install the Galaxy S III unified toolkit, and pull the first 7 partitions from mmcblk0 ,which is where the third bootloader stage ends.(Don't upload a heavily modified device please) http://www.skipsoft.net/?page_id=213 Once you get the files, PM me.
If anyone has a link to a working one, please post that. If you want to get your own image to help me, go ahead.
Thanks guys.
Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.
99ytrewq9111 said:
Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.
Click to expand...
Click to collapse
what happened?
winosxbuntu said:
what happened?
Click to expand...
Click to collapse
I tried to unlock what I thought was a locked bootloader(I could only enter bootloader through ADB)
I found an article that says ezunlock works on all S III's.
It corrupted my bootloader,and my phone gives off no signs of life except "Device QHSUSB-DLOAD not recognized" when plugged in.
This means the motherboard/processor wasn't able to boot from the hard disk, so then it tries the SDcard if it matches the phone close enough.
I need someone to use their rooted i747 to dump the first 77.3 megabytes of "mmcblk0". That contains the firmware and bootloaders. With that, i can burn it to an sdcard in a linux operating system and plug it into my phone.
99ytrewq9111 said:
Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.
Click to expand...
Click to collapse
99ytrewq9111 said:
I tried to unlock what I thought was a locked bootloader(I could only enter bootloader through ADB)
I found an article that says ezunlock works on all S III's.
It corrupted my bootloader,and my phone gives off no signs of life except "Device QHSUSB-DLOAD not recognized" when plugged in.
This means the motherboard/processor wasn't able to boot from the hard disk, so then it tries the SDcard if it matches the phone close enough.
I need someone to use their rooted i747 to dump the first 77.3 megabytes of "mmcblk0". That contains the firmware and bootloaders. With that, i can burn it to an sdcard in a linux operating system and plug it into my phone.
Click to expand...
Click to collapse
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:
winosxbuntu said:
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:
Click to expand...
Click to collapse
Thanks for that link! It looks very promising, and I can probably find a stock boot.IMG in there. I will work on tomorrow. If I succeed, I'll edit the OP and make a debrick guide for this drvice forum. A word of advice, try not to mess with your bootloader or you end up like me
winosxbuntu said:
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:
Click to expand...
Click to collapse
Hi, the toolkit didn't fix my phone, but its defiantly a step up. Since I'm assuming you have the toolkit installed that you suggested it, could you do me a favor?
It will be a bit easier using the toolkit to extract the partition files. If you could pull the first 7 partitions from "mmcblk0" of your device through the toolkit, it will probably set the next step to fix my phone. (Assuming you have a 16g i747... I don't really know)
You don't have to do this of course.
Thanks man.
Bump. Can anyone help out? All I need is the first 7 partitions.
Sent from my GT-I9300 using xda app-developers app
99ytrewq9111 said:
Bump. Can anyone help out? All I need is the first 7 partitions.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
either try using this link http://forum.xda-developers.com/showpost.php?p=27239761 am pretty sure it works for all S3 models, either way on the I747 forum it has been removed, the download link does not work........ so use this
it will work, it may not work but for the time being use this toolkit and also search forums or Google on how to fix this without, i think i found some answers after i had an emmc brick with my S2 but i did not have an SD card to re-write firmware to work again on my phone so i bought the S3 and its awesome
winosxbuntu said:
either try using this link http://forum.xda-developers.com/showpost.php?p=27239761 am pretty sure it works for all S3 models, either way on the I747 forum it has been removed, the download link does not work........ so use this
it will work, it may not work but for the time being use this toolkit and also search forums or Google on how to fix this without, i think i found some answers after i had an emmc brick with my S2 but i did not have an SD card to re-write firmware to work again on my phone so i bought the S3 and its awesome
Click to expand...
Click to collapse
The problem is I need a working phone to pull the partitions. :/ I tried to use the boot image, but it had an error writing while in the linux.
99ytrewq9111 said:
The problem is I need a working phone to pull the partitions. :/ I tried to use the boot image, but it had an error writing while in the linux.
Click to expand...
Click to collapse
This one worked for me http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172
I have a similar problem Hard Bricked after update to 4.3 tried to flash my phone Backup 4.1.2 and died can not log in or recovery nor danlold.Is there any solution.
Bradkirk said:
This one worked for me http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172
Click to expand...
Click to collapse
Did you use an i747 or a i747m device?
If a i747m image works on an i747, it will basically fix all of my problems.
spensa said:
I have a similar problem Hard Bricked after update to 4.3 tried to flash my phone Backup 4.1.2 and died can not log in or recovery nor danlold.Is there any solution.
Click to expand...
Click to collapse
What message appears on your computer when you plug it in?
If it says QHSUSB-DLOAD, you are in faint light.
It stands for Qualcomm High Speed USD Download Mode.
What is means that your processor(qualcomm), is trying to boot, but it cannot find proper drivers for the hardware.
It will then look for something to boot from in the SDcard.
Here is a thread on how some other people were able to do it : http://forum.xda-developers.com/showthread.php?t=2439367
I have an I747M technically. I went for an actual I747M image just in case there was a slight difference. in the thread that one came from though there should be one for the actual att device if you look through it.
and just to confirm, yes the phone was blank and unresponsive. showing up as QHSUSB-DLOAD before i loaded that img onto my external SDcard. and I am using the same phone currently.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Bradkirk said:
I have an I747M technically. I went for an actual I747M image just in case there was a slight difference. in the thread that one came from though there should be one for the actual att device if you look through it.
and just to confirm, yes the phone was blank and unresponsive. showing up as QHSUSB-DLOAD before i loaded that img onto my external SDcard. and I am using the same phone currently.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Unfortunately that's the download I found that didn't work.
Thanks for trying though
damn! the only other help I can offer then, is that there is a pretty good thread on this over in the d2tmo section. someone there wrote a little tool to easily download the relevant data. might help you on your quest. or at least make it so you could ask someone that doesnt know ADB. best of luck!
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
99ytrewq9111 said:
What message appears on your computer when you plug it in?
If it says QHSUSB-DLOAD, you are in faint light.
It stands for Qualcomm High Speed USD Download Mode.
What is means that your processor(qualcomm), is trying to boot, but it cannot find proper drivers for the hardware.
It will then look for something to boot from in the SDcard.
Here is a thread on how some other people were able to do it : http://forum.xda-developers.com/showthread.php?t=2439367
Click to expand...
Click to collapse
when connected to the computer written QHSUSB-DLOAD,
spensa said:
when connected to the computer written QHSUSB-DLOAD,
Click to expand...
Click to collapse
OK , take out your battery and tell me your model number(Behind battery). And what phone company do you use?
Did you possibly save a NANDROID on a computer?
( if you have i747m, you can fix your phone, but its hard to do( I havnt done it yet)
Download this image http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172 (thanks to @Bradkirk )
Follow these directions using that image above^^^ http://forum.xda-developers.com/showthread.php?t=2439367
You need to install a Linux operating system (Ubuntu works) to run the commands.
Edit:! According to the T-Mobile thread, you might need a debrick.IMG from a phone on 4.3
Once I know your phones model number, I can edit the main post and ask for you phone model's images.
99ytrewq9111 said:
OK , take out your battery and tell me your model number(Behind battery). And what phone company do you use?
Did you possibly save a NANDROID on a computer?
( if you have i747m, you can fix your phone, but its hard to do( I havnt done it yet)
Download this image http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172 (thanks to @Bradkirk )
Follow these directions using that image above^^^ http://forum.xda-developers.com/showthread.php?t=2439367
You need to install a Linux operating system (Ubuntu works) to run the commands.
Edit:! According to the T-Mobile thread, you might need a debrick.IMG from a phone on 4.3
Once I know your phones model number, I can edit the main post and ask for you phone model's images.
Click to expand...
Click to collapse
I took it to a service to repair
So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.
omeadsthename said:
So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.
Click to expand...
Click to collapse
i looked all over the internet for this. finally the right 4.4~ is found
https://www.androidfilehost.com/?w=files&flid=15759
The i747 bootloader is not locked. I have no idea what that Verizon app would have done, but if that's what bricked it, our debrick method may not work. We also have not been able to restore any 4.4.2 bricks yet. Thats why i posted a new script to create the image, in hopes that doing it a little differently would help.
I wish you luck, but considering how it was bricked, dont get your hopes up too much. Its still worth trying of course, but i have a feeling a jtag service might be the only way.
did same on my first s3 i747. tried to unlock a already unlocked bootloader. before i knew any better, went and got a new s3. (back in my pre-newb days...before i could even claim newbness status.lol), then discovered XDA. started reading and found out about jtag. now that s3 belongs to my brother.
not helpful, i know. just my story.good luck with debrick.img method.
:thumbup:
err on the side of kindness
Anybody know where I can get a debrick image for 4.1.2 (i747) ??
- Guy in desperate need who's been googling for wayy too long now
think theres one here.
http://forum.xda-developers.com/showthread.php?t=2525902
thanks to @DocHoliday77
good luck
err on the side of kindness
mrrocketdog said:
think theres one here.
http://forum.xda-developers.com/showthread.php?t=2525902
thanks to @DocHoliday77
good luck
err on the side of kindness
Click to expand...
Click to collapse
Thank you... Here goes nothing.
let us know how it goes.
err on the side of kindness
mrrocketdog said:
let us know how it goes.
err on the side of kindness
Click to expand...
Click to collapse
Unfortunately it did not work
I was orignally on 4.1.2 and flashed task650's newest AOKP release with CWM but for some reason was bootlooping and could not get past the "Swagger Activated" boot animation. So then I tried to revert back to the stock rom via Odin but I must have tried flashing a 4.3 stock rom because it's bricked pretty good now. Odin does not recognize the phone - device manager displays it as QSHUSB_DLOAD. I've tried making my own jig with no luck. And just recently, I've tried 3 different i747 debrick images using the sd card method (16gb / class 10). Up until just an hour ago, I could take the battery out and plug the phone into my laptop via usb cable and the red light would come on but that doesn't even happen anymore. When I hold down the 3 button combination everynow and then I'll hear Windows "device connect noises" as if it's trying to connect but nothing will happen. I know the correct Samsung drivers are installed on my pc because everything was showing up fine prior to me flashing the AOKP rom.
I'm beginning to think there no more hope for me. Idk if I wan't to bother having my phone shipped out and serviced or JTAG'ed or whatever.
Have you tried different sd cards. Many people find some won't work, while others do.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
omeadsthename said:
So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.
Click to expand...
Click to collapse
Try this Its a debrick image from a 4.4.2 SGH-1747 >>> filedropper.com/debrick <<<
Ehaeli said:
Try this Its a debrick image from a 4.4.2 SGH-1747 >>> filedropper.com/debrick <<<
Click to expand...
Click to collapse
do you have the actual link for that file?
think it might be in this thread..
http://forum.xda-developers.com/showthread.php?t=2820019
REMEMBER please....backup and read read read.
good luck:thumbup:
err on the side of kindness
Looking for a debrick image
Hello, I am looking for someone who can upload a debrick image for I747mvlufnh2 4.4.2 for the 16gb I have searched everywhere without any luck.
Gal tales said:
Hello, I am looking for someone who can upload a debrick image for I747mvlufnh2 4.4.2 for the 16gb I have searched everywhere without any luck.
Click to expand...
Click to collapse
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url
I need some for i747 only please !!!!
mitch0422 said:
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url
Click to expand...
Click to collapse
Im from mexico. And hard bricked my s3 i flashed a canadian nk2 kk. But when i turn it off never came on againg. So please help me. Im new to all this. I need examples with potatoes. Lol. What else do i need besides this image..
Enviado desde mi GT-I9505 mediante Tapatalk
bighleo114312 said:
Im from mexico. And hard bricked my s3 i flashed a canadian nk2 kk. But when i turn it off never came on againg. So please help me. Im new to all this. I need examples with potatoes. Lol. What else do i need besides this image..
Enviado desde mi GT-I9505 mediante Tapatalk
Click to expand...
Click to collapse
you can try here .....
http://forum.xda-developers.com/showthread.php?t=2549068
i see you found it. nevermind.
"all i can really do , is stay out of my own way and let the will of heaven be done"
mitch0422 said:
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url
Click to expand...
Click to collapse
Mitch0422 i have downloaded the 4.4.2 image but i cant turn on my s3. Do i just need to write it to sd and turn on s3?
Enviado desde mi SCH-I535 mediante Tapatalk
Yes
bighleo114312 said:
Mitch0422 i have downloaded the 4.4.2 image but i cant turn on my s3. Do i just need to write it to sd and turn on s3?
Enviado desde mi SCH-I535 mediante Tapatalk
Click to expand...
Click to collapse
Sorry for the long wait for reply . i don't often check my email. To answer you question . Yes you have to write it to the microsd as a bootable image then insert the microsd and boot the phone . it might take awhile of holding down the power button before it shows signs of life. You might also have to take the battery out and try a few times . Once you have it booted back up use Odin to flash the stock rom back onto your phone then take out the sd card and try to turn it on. Follow these directions youtube.com/watch?v=8MnikrpUKZw
I was updating an s3 running cyanogenmod 10.2.1 to 11. I realized that the bootloader needed to be updated long story short i accidentally flashed the i9300 bootloader instead and now my phone is hard bricked. I heard about a method using the sd card to allow the phone to enter boot recovery so i could get into download mode could someone help me to do this?
The only fix that I personally know of is using a jtag service. If there is an sd card fix floating around out there, you'll need to search for it. If you fail, mobiletechvideos.com can help. Expect a week to 10 day turn around time
Sent from my SAMSUNG-SGH-I747 using Tapatalk
purelight97 said:
I was updating an s3 running cyanogenmod 10.2.1 to 11. I realized that the bootloader needed to be updated long story short i accidentally flashed the i9300 bootloader instead and now my phone is hard bricked. I heard about a method using the sd card to allow the phone to enter boot recovery so i could get into download mode could someone help me to do this?
Click to expand...
Click to collapse
You are probably referring to the method posted in the thread below ....
http://forum.xda-developers.com/showthread.php?t=2549068
You have nothing to lose in giving it a try. Doubtful if it will work, however, since it is specifically for recovering from a brick caused by flashing an older bootloader after 4.3 upgrade. As BrianRay advised, when you have a brick caused by flashing a different model's bootloader, a JTag operation may be required.
Larry2999 said:
You are probably referring to the method posted in the thread below ....
http://forum.xda-developers.com/showthread.php?t=2549068
You have nothing to lose in giving it a try. Doubtful if it will work, however, since it is specifically for recovering from a brick caused by flashing an older bootloader after 4.3 upgrade. As BrianRay advised, when you have a brick caused by flashing a different model's bootloader, a JTag operation may be required.
Click to expand...
Click to collapse
Thanks, you wouldn't happen to have a 4.1.2 debrick.img?
purelight97 said:
Thanks, you wouldn't happen to have a 4.1.2 debrick.img?
Click to expand...
Click to collapse
Sadly, no, I don't. You could create one, however, if you know someone who has a similar device running 4.1.2. If you need further instructions on how to do this, you would need to contact the author of the original post. He is the expert there. A JTag may still be your best option, however.
Hey, try to get the phone into a download mode by using at USB jig. You can buy one for 3 bucks from ebay. If that doesnt do it, then you can go to the method of using the debrick image.
Once you exhaust all of these possibilities, then you can try the JTAG. But the Jtag service is expensive too. Good luck.
Hello people, I randomly tried to flash internation model rom on my i747 model s3
it gave wrong model error so i went and modified asserts in the update file and made it pass the check. but phone wont turn on now. i do get red led when charging it. I know it sounds stupid but i just wanted to give a try (was assuming I would unlock the phone :laugh
anyways i do know that 16gb sd un-brick method. but i was wondering if there's a possible different method.
thanks for your time.
Only paying for a jtag service
looks like SD Unbrick method isn't working either, it's not turning on with unbrick sd. i did do a backup before all this. can anyone help here?
Dont give up. Many people have to run through the sd creation process several times before it worked.
It could also be the sd card you are using.
DocHoliday77 said:
Dont give up. Many people have to run through the sd creation process several times before it worked.
It could also be the sd card you are using.
Click to expand...
Click to collapse
the thing is, all debrick img's posted on threads are for 4.3 and up. my phone was on 4.1.2 with an i747 bootloader.
going to order a usb jig (since diy's failed)
If you are on pre-4.3 firmware, it shouldn't matter what debrick.img you use. But if you do get it to boot it will not let you flash anything older than what the image is.
---------- Post added at 03:31 AM ---------- Previous post was at 03:31 AM ----------
Of course it wouldn't hurt to have a 4.1.2 image.....
troolplay1 said:
the thing is, all debrick img's posted on threads are for 4.3 and up. my phone was on 4.1.2 with an i747 bootloader.
going to order a usb jig (since diy's failed)
Click to expand...
Click to collapse
It is a good idea to have a jig handy. But you many not even need it for that one. The exact same thing happened to me (I747m - Fido).
Just make sure the SD card is the same size as your phone for the image.
I am assuming you already found all the steps? You can pm me if you need the necessary files.
distorsun said:
It is a good idea to have a jig handy. But you many not even need it for that one. The exact same thing happened to me (I747m - Fido).
Just make sure the SD card is the same size as your phone for the image.
I am assuming you already found all the steps? You can pm me if you need the necessary files.
Click to expand...
Click to collapse
I have tried many many debirck img's. both for t999 and i747, for 4.3 and whatnot. today i got the jig in the mail but the try failed, still wont turn on. i lost hope and i feel like sending it to ebay service is my only resort. the sd card i was using was a pixar class 10 16GB. idk what would go wrong with that.
the reason that i bricked it, again, is flashing wrong bootloader.
any help would be appreciated.
Idk bro the international s3 is a whole nother phone, it has a quad core exynos processor while we got a dual core snapdragon, it's got a gig of ram we got 2.... That's too name a few differences.....I think the only way to fix it is by a JTAG.......sorry bout the luck bro
O don't think he's got an international version. Thought he mentioned having an I747 before??
Sent from my SAMSUNG-SGH-T999 using Tapatalk
If you don't mind shipping to Canada I have a riffbox and could fix the issue for you.
The debrick method should work though. If it were me I wouldn't give up just yet. I'd at least try a few more times on every sdcard I could get a hold of. Often doesn't work on the first couple of tries, and AFAIK there's no way to know which sdcards will or won't work. Just gotta keep trying.
It is possible that for some reason this method simply won't work, but it has worked in the past for similar types of bricks.
Sent from my SAMSUNG-SGH-T999 using Tapatalk