Develop Bugs

[Q] No voice

To make a long story short I was in CM11 and when trying to restore to stock I tripped the Knox Counter. I no longer have voice or audio. I tried to restore to other custom roms with same issue. I tried downloading stock tmobiles images and am unable to restore with odin. Question after triggering the Knox does that not allow me to even restore a stock rom or is my issue some place else? Any help?

It's my understanding you can not Odin back to MDL but you should be able to Odin the MK2 firmware.
☞ Sent from here☜???

re: knox
ahoslc said:
To make a long story short I was in CM11 and when trying to restore to stock I tripped the Knox Counter. I no longer have voice or audio. I tried to restore to other custom roms with same issue. I tried downloading stock tmobiles images and am unable to restore with odin. Question after triggering the Knox does that not allow me to even restore a stock rom or is my issue some place else? Any help?
Click to expand...
Click to collapse
If you are sure that you tripped the knox counter this is how to fix the audio issue.
Download the official M919 STOCK 4.3 MK2 firmware/rom from http://SamMobile.com .
(filename: M919UVUEMK2_M919TMBEMK2_TMB.zip inside zip is the tar file)
Then Odin flash the tar in Odin's PDA slot.
After you odin flashed the 4.3 MK2 successfully see if the audio/sound/voice is good.
If it's not then download the latest KToonsez 12-12-2013 kernel and flash it using
cwm/twrp recovery. (after the phone is rooted)
Here is the direct download link for KToonsez kernel:
https://copy.com/kEWuwwaGj8j2/TW%20JB%204.3%20Versions/KT-SGS4-JB4.3- TW-TMO-12.12.2013.zip?download=1
Before you can cwm/twrp flash the kernel or any cwm/twrp flashable zip file you need to
be rooted.
Here is the direct download link for the odin flash CF-AUTOROOT:
http://download.chainfire.eu/328/CF...jfltetmo-jfltetmo-sghm919.zip?retrieve_file=1
It's always best in any case to flash the KToonsez kernel after flashing new roms.
Good luck!

It's always best in any case to flash the KToonsez kernel after flashing new roms.
WHy is this kernel so famous and need to install after installing new ROMs? -
Good luck![/QUOTE]

Misterjunky said:
If you are sure that you tripped the knox counter this is how to fix the audio issue.
Download the official M919 STOCK 4.3 MK2 firmware/rom from http://SamMobile.com .
(filename: M919UVUEMK2_M919TMBEMK2_TMB.zip inside zip is the tar file)
Then Odin flash the tar in Odin's PDA slot.
After you odin flashed the 4.3 MK2 successfully see if the audio/sound/voice is good.
If it's not then download the latest KToonsez 12-12-2013 kernel and flash it using
cwm/twrp recovery. (after the phone is rooted)
Here is the direct download link for KToonsez kernel:
https://copy.com/kEWuwwaGj8j2/TW%20JB%204.3%20Versions/KT-SGS4-JB4.3- TW-TMO-12.12.2013.zip?download=1
Before you can cwm/twrp flash the kernel or any cwm/twrp flashable zip file you need to
be rooted.
Here is the direct download link for the odin flash CF-AUTOROOT:
http://download.chainfire.eu/328/CF...jfltetmo-jfltetmo-sghm919.zip?retrieve_file=1
It's always best in any case to flash the KToonsez kernel after flashing new roms.
Good luck!
Click to expand...
Click to collapse
I am having the same issue as the OP. But my understanding is, with Knox (which I unfortunately seem to have acquired, my fault) I cannot use Odin to flash a tar file.

You can still flash. You may trip the counter and you can't flash back to 4.2, but Odin still works.
Sent from my SGH-M919 using XDA Premium 4 mobile app

At this point knox is already tripped, and that's okay. But to resolve my loss of sound and voice I would have to use Odin to flash a T-Mo 4.3 tar, such as the one above? This will flash everything, including modem, right?
Could i also Odin flash the full TMo 4.3 modem with the same results?

re: knox
alouden said:
I am having the same issue as the OP. But my understanding is, with Knox (which I unfortunately seem to have acquired, my fault) I cannot use Odin to flash a tar file.
Click to expand...
Click to collapse
Not being able to flash tar files with odin due to having knox
must be some kind of rumor, but that's all it is a rumor.
It's not true at all.
Good luck!

Misterjunky said:
Not being able to flash tar files with odin due to having knox
must be some kind of rumor, but that's all it is a rumor.
It's not true at all.
Good luck!
Click to expand...
Click to collapse
Thanks. Will be doing this later at home. Fingers crossed :good:

Misterjunky said:
Not being able to flash tar files with odin due to having knox
must be some kind of rumor, but that's all it is a rumor.
It's not true at all.
Good luck!
Click to expand...
Click to collapse
Intersting...I Odin flashed the latest update. During the flash, I did see modem being flashed in the progress window. Still Have the same issue. I am confused. Not sure why this did not work.

re: modem/baseband/mdl/mk2
alouden said:
At this point knox is already tripped, and that's okay. But to resolve my loss of sound and voice I would have to use Odin to flash a T-Mo 4.3 tar, such as the one above? This will flash everything, including modem, right?
Could i also Odin flash the full TMo 4.3 modem with the same results?
Click to expand...
Click to collapse
Here are the step by step instruction on how to get the MK2 modem.bin
baseband flashed successfully.
Here is the way to fix the audio issue you are having.
This will ONLY fix your audio issue if your baseband is MDL
so check your baseband by going to Settings>More>About device
and scroll down after clicking About device til you see baseband.
It will either have MK2 or MDL in it. If it's MDL then your
audio issue can be fixed by following the instructions below.
You can Odin flash MK2 while on an Wicked v9.1 4.2.2 rom or ODIN
flash it after flashing the Wicked v9.1 4.3 or other M919 based 4.3 roms.
Either way it makes no difference.
What does make a difference is to follow this step by step exactly to a "T".
#1: Manually power down the phone using the power button only
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot/tab.
#3: Put the phone into download mode by using the volume down and power button only.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone using the power button.
#9: Wait 20 or so seconds before you power on the phone.
After doing this the MK2 baseband should show up in About Device.
Here is the direct download link for the Tmobile 4.3 M919 MK2 modem.bin:
http://www.mediafire.com/download/1g...l89x/modem.bin
After your baseband displays MK2 you don't need to do anything,
the phone will then be ready to use with all it's bells and whistles.
I would highly suggest that you make a nandroid backup in TWRP recovery before you
change any settings, installing or flashing any apps, mods, themes or anything else.
Good luck!

Misterjunky said:
Here are the step by step instruction on how to get the MK2 modem.bin
baseband flashed successfully.
Here is the way to fix the audio issue you are having.
This will ONLY fix your audio issue if your baseband is MDL
so check your baseband by going to Settings>More>About device
and scroll down after clicking About device til you see baseband.
It will either have MK2 or MDL in it. If it's MDL then your
audio issue can be fixed by following the instructions below.
You can Odin flash MK2 while on an Wicked v9.1 4.2.2 rom or ODIN
flash it after flashing the Wicked v9.1 4.3 or other M919 based 4.3 roms.
Either way it makes no difference.
What does make a difference is to follow this step by step exactly to a "T".
#1: Manually power down the phone using the power button only
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot/tab.
#3: Put the phone into download mode by using the volume down and power button only.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone using the power button.
#9: Wait 20 or so seconds before you power on the phone.
After doing this the MK2 baseband should show up in About Device.
Here is the direct download link for the Tmobile 4.3 M919 MK2 modem.bin:
http://www.mediafire.com/download/1g...l89x/modem.bin
After your baseband displays MK2 you don't need to do anything,
the phone will then be ready to use with all it's bells and whistles.
I would highly suggest that you make a nandroid backup in TWRP recovery before you
change any settings, installing or flashing any apps, mods, themes or anything else.
Good luck!
Click to expand...
Click to collapse
Thanks for the detailed steps. So when I check baseband, I see that I have the MK2 baseband.

re: no more issues
alouden said:
Thanks for the detailed steps. So when I check baseband, I see that I have the MK2 baseband.
Click to expand...
Click to collapse
If you have MK2 baseband then you should have proper audio, no audio issues at all
and the rest of your phone should be working fine since it's already rooted and the
phone has the best custom recovery already flashed in it.
Be sure to make a nandroid backup using Twrp recovery before downloading,
installing, adding or flashing any mods, apps, themes or anything else.
Good luck!

Misterjunky said:
If you have MK2 baseband then you should have proper audio, no audio issues at all
and the rest of your phone should be working fine since it's already rooted and the
phone has the best custom recovery already flashed in it.
Good luck!
Click to expand...
Click to collapse
In a perfect world, yes. Not this time....I still have no sounds. And no audio on phonecalls. On the threat of divorce, my wife has made me promise to resolve this one way or another. All my efforts have failed. i am now stock 4.3, rooted, with twrp recovery. no sound.
Ah well...Happy New Year. And thanks to everyone for their help. I haven't given up. But my wife has a good lawyer.

Misterjunky said:
If you have MK2 baseband then you should have proper audio, no audio issues at all
and the rest of your phone should be working fine since it's already rooted and the
phone has the best custom recovery already flashed in it.
Be sure to make a nandroid backup using Twrp recovery before downloading,
installing, adding or flashing any mods, apps, themes or anything else.
Good luck!
Click to expand...
Click to collapse
Figured out the problem. So the MK2 Tar file I had was the culprit. I redownloaded the file from a different source, re-extracted the Tar and used Odin to reflash the tar file. Funny, the first file did not have a MD5 mismatch and did flash a modem. Well, whatever the issue was, I am glad it was resolved. Thanks for all your help guys.

[Q] m919nuvuemk5 HELP!

Ok, I am not new to flashing but its not somthing I do on a regular basis...I got in a hurry and screwed up my phone.
I have been running cyanogenmod 10.2 and my wife has the same phone that I left stock. They are T-Mobile Galaxy S4 SGH-M919. Yesterday I poked around a bit and found the most up to date rom I could, it was m919nuvuemk5. What I failed to notice was that this rom is for Metro PCS which may be owned by t-mobile , but is definitly not t-mobile.... I flashed and it boots all the way to the Metro PCS splash screen and thats where it stops. SO...I started looking around a bit more and found the thread - [GUIDE][HOW-TO] Return device back to stock 'Official'!
at :
http://forum.xda-developers.com/showthread.php?t=2336392
So the short version is that right now the rom I have flashed is m919nuvuamdb but my base band is still m919nuvuemk5 and my knox fuse is popped 0x1 The phone works fine but I have no wifi I did factory resets and wiped everything trying to get the wifi working but sofar no joy. I can root with CF-Auto-Root via ODIN with no problem. :good: I can apply custom recoveries like CWM with no problem. :good:
So all is not lost.
My questions are:
1. It is my understanding that at this time there is no way to remove the Knox 0x1 that says my phone is trash for corporate use. :cyclops: Is this true?
2. My boot times are very long, (2m 10s) it seems to hang on the "Samsung Galaxy S4" screen where it says " kernel is not seandroid enforcing set warrenty bit: kernel" Is there a way to make the warning go away? How about a shorter boot time? I think if t-mobile comes out with a m919nuvuemk5 rom I should be ok and the warnings will go away atleast. Is this right?
3. How do I make my wifi work?
I could really use some help with this, I have been reading allover these boards for a day. Please save your chastising for your children, know I screwed up. Just lead me in the right direction.

Try flashing the mk2 modem.
If that don't work you might have to Odin flashed the whole 4.3 firmware.
☞ Sent from here☜???

baseballfanz said:
Try flashing the mk2 modem.
If that don't work you might have to Odin flashed the whole 4.3 firmware.
☞ Sent from here☜???
Click to expand...
Click to collapse
Where can I find just the modem?

This is how I did that: the file is in the op. http://forum.xda-developers.com/showthread.php?t=2544612
Sent from my SGH-M919 using XDA Premium 4 mobile app

Android_Monsters said:
This is how I did that: the file is in the op. http://forum.xda-developers.com/showthread.php?t=2544612
Sent from my SGH-M919 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Went there , did that , did'ent work. It did improve my boot times significantlly though. so Thanks! :good:
Think Ill flash : ROM|TW|4.3|MK2] Modified Stock M919UVUEMK2 V1.4 [CIQ|KNOX-FREE][12/10/2013]
and see how that works...

still no luck
Ok so I have flashed the above rom and even went back to cyanogenmod but Im still having problems. My wifi works fine now , but my phone has no sound...at all, I cannot make or recieve calls.

re: modem.bin
Jimcisme said:
Ok so I have flashed the above rom and even went back to cyanogenmod but Im still having problems. My wifi works fine now , but my phone has no sound...at all, I cannot make or recieve calls.
Click to expand...
Click to collapse
Why not try this easy to follow step by step instructions. This is how I done it myself.
#1: Manually power down the phone by using the power button only.
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot.
#3: Put the phone into download mode by using the volume down and power button only.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone using the power button.
#9: Wait 20 or so seconds before you power on the phone.
After doing this the MK2 baseband should show up in About Device.
Once you have done this successfully you will no longer have
audio or wifi issues.
Here is the direct download link for the 4.3 MK2 modem.bin:
http://www.mediafire.com/download/1g...l89x/modem.bin
Also if you have never Odin flashed the new full stock
4.3 MK2 Galaxy S4 TW Jellybean firmware/rom then
you don't have knox and you don't need to worry about
it unless you odin flashed the full firmware/rom.
You cannot get KNOX by simply odin flashing the MK2 MODEM.BIN file.
Good luck!

Jimcisme said:
Ok so I have flashed the above rom and even went back to cyanogenmod but Im still having problems. My wifi works fine now , but my phone has no sound...at all, I cannot make or recieve calls.
Click to expand...
Click to collapse
You need to get the correct modem on your phone. Flashing ROM will not change the modem so you will continue to have problems.
☞ Sent from here☜???

FIXED
baseballfanz said:
You need to get the correct modem on your phone. Flashing ROM will not change the modem so you will continue to have problems.
☞ Sent from here☜???
Click to expand...
Click to collapse
Hi, I did manage to get it straightened out.
1. Rooted the Phone with CF-Auto-Root via ODIN Thanks to Chainfire :good: http://forum.xda-developers.com/showthread.php?t=2294005
2. Did factory reset in recovery.
3. Flashed the 4.3 MK2 modems (plural) from http://www.mediafire.com/download/1gsjokadys4l89x/modem.bin from the link Misterjunky :good: provided.
4. Flashed this ROM- Build Date: 16.11.2013 -> Region: TMB (USA (T-Mobile)) PDA: M919UVUEMK2 Changelist: 2015522 Android: 4.3
From this page : http://forum.xda-developers.com/showthread.php?t=2267895 Thanks to AdamLange :good:
It is possible that I did not need to flash the modems as when I flashed the rom it loaded a modem.bin file. But I figured better safe than sorry. This is a rom from samsung as far as I can tell, It took much longer to flash than all the others I flashed. It got rid of the "Kernel is not seandroid enforcing " message I had at the boot loader too. Everything works good so far! I may try to root again later.
Thanks too all for all your help!

Jimcisme said:
It is possible that I did not need to flash the modems as when I flashed the rom it loaded a modem.bin file. But I figured better safe than sorry. This is a rom from samsung as far as I can tell, It took much longer to flash than all the others I flashed. It got rid of the "Kernel is not seandroid enforcing " message I had at the boot loader too. Everything works good so far! I may try to root again later.
Thanks too all for all your help!
Click to expand...
Click to collapse
Yes if you use Odin to flash the full firmware it will also flash the modem. If you flash ROM via custom recovery it will not change modem.
☞ Sent from here☜???

trying to flash modem bin

using odin to flash modem bin with 4.3 rom but when i look in about device it will not stick still says mdl 5 times already

re: Odin flashing modem.bin
okay22s said:
using odin to flash modem bin with 4.3 rom but when i look in about device it will not stick still says mdl 5 times already
Click to expand...
Click to collapse
Download the MK2 Modem.bin if you don't already have it.
Here is the direct download link for it: http://www.mediafire.com/download/1g...l89x/modem.bin
Here are the exact step by step instructions for doing that, doing it this way worked fine for me.
Before flashing anything be sure to make a nandroid backup of your rom.
You can Odin flash the MK2 modem while on the 4.2.2 rom or flash it
after flashing Wicked v9.1 MK2 rom the procedure is exactly the same.
Before starting, unplug the usb cable from your phone if it's plugged in
and remove the battery from the phone for 30 seconds then replace.
#1: Power up the phone.
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot/tab.
#3: Un-Check the "Auto-Reboot" check box in ODIN.
#4: Put the phone into download mode
#5: Plug the USB cable into the phone and into the computer.
#6: Make sure that ODIN'S [COM:xx] lights up and click START..
#7: After Odin is done flashing unplug the usb cable.
#8: Manually power off the phone by using the power button only.
#9: Wait 20 seconds or so and power on the phone.
After flashing is done the baseband of the phone should display MK2 in
Settings>More>About Device> Baseband version.
Good luck with it!

Thanks again I'll try that way

okay22s said:
Thanks again I'll try that way
Click to expand...
Click to collapse
After Odin says passed, leave it plugged in for another 30 seconds. Then manually power off the phone. Unplug it, put it in download mode again, replug it, and flash again. Then reboot. It will stick.
Sent from my SGH-M919 using XDA Premium 4 mobile app

Thanks for the info finally got it after six times just thought I was doing something wrong the first couple of times I'm happly running darthstalker ROM with no data drops everything's smooth thanks

okay22s said:
Thanks for the info finally got it after six times just thought I was doing something wrong the first couple of times I'm happly running darthstalker ROM with no data drops everything's smooth thanks
Click to expand...
Click to collapse
Yeah, it can take a while if it is your first time flashing a modem. Glad you have it working, enjoy your ROM!

just so I don't have to create a new thread and my question is somewhat related.
If I move up to 4.3 with root (not bootloader) and decide I want to come back to 4.2, will I have to flash the 4.2 (mdl) LTE modem or can the 4.3 (mk2) LTE modem work fine?

aamir123 said:
just so I don't have to create a new thread and my question is somewhat related.
If I move up to 4.3 with root (not bootloader) and decide I want to come back to 4.2, will I have to flash the 4.2 (mdl) LTE modem or can the 4.3 (mk2) LTE modem work fine?
Click to expand...
Click to collapse
The mk2 modem work just fine with mdl firmware. I was using it for over a week on mdl before flashing a 4.3 ROM.
☞ Sent from here☜???

[Q] S4 signal issues after upgrade

I have a stock S4 and had no problems in 4.2.2 but when I upgraded to 4.3, my texts don't send and I seem to lose signal. Like the bars show up and everything but they just fail to send and I don't receive any phone calls either. I was wondering if anyone had a solution to this and I already factory reset my phone and upgraded again, but it really didn't seem to work and I got a new sim card as well.

I'd Odin to stock.
Sent from my SGH-M919 using XDA Premium 4 mobile app

re: reception issues
DoubleAKash said:
I have a stock S4 and had no problems in 4.2.2 but when I upgraded to 4.3, my texts don't send and I seem to lose signal. Like the bars show up and everything but they just fail to send and I don't receive any phone calls either. I was wondering if anyone had a solution to this and I already factory reset my phone and upgraded again, but it really didn't seem to work and I got a new sim card as well.
Click to expand...
Click to collapse
How did you do the upgrade, OTA, Kies or did you simply use cwm/twrp to flash a zip file custom rom?
If all you did was flash a cwm/twrp 4.3 zip file custom rom then follow these step by step instructions
below to fix your signal/data & reception issues by flashing the 4.3 MK2 stock modem.bin file in Odin.
Please NOTE: the following procedure is NOT valid for AOSP/AOKP/KitKat/CM roms.
The following instructions are exclusively for those people who are using the
Tmobile M919 stock based Jellybean 4.2.2 or 4.3 Touchwiz custom roms.
Follow the easy step by step instructions to a "T".
You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
What does make a difference is to follow this step by step exactly.
#1: Manually power down the phone by using the power button only.
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot.
#3: Put the phone into download mode using the volume down and power button.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone by using the power button only.
#9: Wait 30 seconds or so before powering up the phone using power button only.
After doing this the MK2 baseband should show up in About Device.
Once it displays MK2 you can flash any MK2 JB TW 4.3 custom cwm/twrp zip file roms unless you have
already flashed it before flashing the modem.bin in which case you're done & ready to use the phone.
Here is the direct download link for the Tmobile 4.3 M919 MK2 modem.bin:
http://www.mediafire.com/download/1g...l89x/modem.bin
Good luck!

[Q] MK2 Modem FAIL'S on Odin

I am having trouble updating my modem to the new MK2. I have tried several times following the instructions
found in various places here on XDA, but nothing works.
_________________________________________________
Phone: SGH-M919 ( Galaxy 4 )
Carrier: T-Mobile LTE
Location: Phoenix
Custom ROM: DARTHSTALKER S4 v.X1 (MK2 & MDL Compliant)
Android version: 4.3 <<<<---- Is this a problem Im on 4.3 ?
Baseband: M919UVUAMDL
Kernel: 3.4.0-g4fe9989-dirty.joy23 #1
SELinux status: Permissive
This is what I am doing to try to update modem.....
1. Open Odin on PC (Mobile Odin doesn't run on G4 T-Mobile.LTE USA)
2. Uncheck Auto-Reboot / Load Modem.bin in the phone tab
3. Boot the phone into Download Mode via power & vol down
4. Plug USB into PC and PHONE
5. I see the BIG GREEN DROID
In the upper left corner of the phone, in tiny font it says:
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
Back on Odin now.....
The ID:COM tab in Odin turns blue and looks good to go. I click on "START".
The bar above ID:COM slowly fills with green. BUT when it is finished, the box above the ID:COM
turns RED and says FAILED !!.
### SEE PICTURE BELLOW ###
Back on the phone the tiny print in the upper left corner now says:
ODIN MODE
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
START [224,1440]
SECURE CHECK FAIL : NDN
Why is it failing ??? Is it because I am on a 4.3 ROM ?
Please help me ....
Thanks
.

Follow this thread:
http://forum.xda-developers.com/showthread.php?t=2544612
There might be something wrong with the file. The bootloader is not accepting it due to failed authentication. Be aware that when updating, you won't see the baseband version as UVUEMK2. You'll just see the old MDL one. This is because you can only update to one of the modem files without any issues.

I have absolutely the same problem - Nothing helps - I have followed the link that was pasted in the second comment and it simply does not work. Once it fails on my phone I have to try to flash stock 4.2.2 to unbrick my device. I am following all of the posts hopefully some new way to update the modems comes out so that I do not have to lock my bootloader down.

Are you trying to just flash the bin file not tarred?
Sent from my SGH-M919 using Tapatalk

Thibor69 said:
I am having trouble updating my modem to the new MK2. I have tried several times following the instructions
found in various places here on XDA, but nothing works.
_________________________________________________
Phone: SGH-M919 ( Galaxy 4 )
Carrier: T-Mobile LTE
Location: Phoenix
Custom ROM: DARTHSTALKER S4 v.X1 (MK2 & MDL Compliant)
Android version: 4.3 <<<<---- Is this a problem Im on 4.3 ?
Baseband: M919UVUAMDL
Kernel: 3.4.0-g4fe9989-dirty.joy23 #1
SELinux status: Permissive
This is what I am doing to try to update modem.....
1. Open Odin on PC (Mobile Odin doesn't run on G4 T-Mobile.LTE USA)
2. Uncheck Auto-Reboot / Load Modem.bin in the phone tab
3. Boot the phone into Download Mode via power & vol down
4. Plug USB into PC and PHONE
5. I see the BIG GREEN DROID
In the upper left corner of the phone, in tiny font it says:
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
Back on Odin now.....
The ID:COM tab in Odin turns blue and looks good to go. I click on "START".
The bar above ID:COM slowly fills with green. BUT when it is finished, the box above the ID:COM
turns RED and says FAILED !!.
### SEE PICTURE BELLOW ###
Back on the phone the tiny print in the upper left corner now says:
ODIN MODE
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
START [224,1440]
SECURE CHECK FAIL : NDN
Why is it failing ??? Is it because I am on a 4.3 ROM ?
Please help me ....
Thanks
.
Click to expand...
Click to collapse
Please NOTE: the following procedure is NOT valid for AOSP/AOKP/KitKat/CM roms.
The following instructions are exclusively for those people who are using the
Tmobile M919 stock based Jellybean 4.2.2 or 4.3 Touchwiz custom roms.
Follow the easy step by step instructions to a "T".
You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
What does make a difference is to follow this step by step exactly.
First download the MK2 modem.bin from the link below:
http://www.mediafire.com/download/1gsjokadys4l89x/modem.bin
#1: Manually power down the phone by using the power button only.
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot.
#3: Put the phone into download mode using the volume down and power button.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone by using the power button only.
#9: Wait 30 or so seconds before you power on the phone.
After doing this the MK2 baseband should show up in About Device.
Once it displays MK2 you can flash any MK2 JB TW 4.3 custom cwm/twrp
zip file roms unless you have already flashed it before flashing the modem.bin
in which case you are done and ready to use the phone.
Good luck!

Misterjunky said:
Please NOTE: the following procedure is NOT valid for AOSP/AOKP/KitKat/CM roms.
The following instructions are exclusively for those people who are using the
Tmobile M919 stock based Jellybean 4.2.2 or 4.3 Touchwiz custom roms.
Follow the easy step by step instructions to a "T".
You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
What does make a difference is to follow this step by step exactly.
First download the MK2 modem.bin from the link below:
http://www.mediafire.com/download/1gsjokadys4l89x/modem.bin
#1: Manually power down the phone by using the power button only.
#2: Start ODIN and put the MODEM.BIN file into ODIN'S PHONE slot.
#3: Put the phone into download mode using the volume down and power button.
#4: Plug the USB cable into the phone and into the computer.
#5: Make sure that ODIN'S [COM:xx] lights up.
#6: Un-Check the Auto-Reboot in ODIN and click START.
#7: After its done flashing unplug the usb cable.
#8: Manually power off the phone by using the power button only.
#9: Wait 30 or so seconds before you power on the phone.
After doing this the MK2 baseband should show up in About Device.
Once it displays MK2 you can flash any MK2 JB TW 4.3 custom cwm/twrp
zip file roms unless you have already flashed it before flashing the modem.bin
in which case you are done and ready to use the phone.
Good luck!
Click to expand...
Click to collapse
.
.
Hi Misterjunky
I do thank you for the walk through .... but unless I am really blind, I am pretty sure as per my
OP that I did follow your steps to a "T" :angel:. If I missed something, PLEASE point it out for me ??
Everything goes just fine until Odin finishes the flash of the modem.bin and says FAILED.
I think the only difference is that I am running a different ROM than you mention, but you do say:
1) You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
2) Or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
Now since I am running DARTHSTALKER S4 ☆ | VERSION X1 | Aroma | Multi-Carrier | 12.29.2013
( This ROM Is Based On The T-Mobile UVUEMK2 4.3 Base )
Option #1) does not apply to me ... BUT ... option #2) DOES apply to me and this ROM since DarthStalker is 4.3 based.
So I should be able to just Odin flash Modem.bin via your steps correct ?? Or am I wrong ?
Please help me ... my OCD is in overdrive atm
Thanks guys !!
.
PS: Shinyside - Yes I am only flashing Modem.bin since I am already on a MDL there is no need to flash the *MDL.tar.MD5
PSS: Vigs - you wrote "There might be something wrong with the file. The bootloader is not accepting it due to failed
authentication. Be aware that when updating, you won't see the baseband version as UVUEMK2. You'll see the old MDL one.
Yes I have tried the Modem.bin file from 3 sources and the file
is fine. I know I wont see baseband as MK2, but that's not my issue mate. The flash FAILS.
.

Thibor69 said:
.
.
Hi Misterjunky
I do thank you for the walk through .... but unless I am really blind, I am pretty sure as per my
OP that I did follow your steps to a "T" :angel:. If I missed something, PLEASE point it out for me ??
Everything goes just fine until Odin finishes the flash of the modem.bin and says FAILED.
I think the only difference is that I am running a different ROM than you mention, but you do say:
1) You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
2) Or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
Now since I am running DARTHSTALKER S4 ☆ | VERSION X1 | Aroma | Multi-Carrier | 12.29.2013
( This ROM Is Based On The T-Mobile UVUEMK2 4.3 Base )
Option #1) does not apply to me ... BUT ... option #2) DOES apply to me and this ROM since DarthStalker is 4.3 based.
So I should be able to just Odin flash Modem.bin via your steps correct ?? Or am I wrong ?
Please help me ... my OCD is in overdrive atm
Thanks guys !!
.
PS: Shinyside - Yes I am only flashing Modem.bin since I am already on a MDL there is no need to flash the *MDL.tar.MD5
PSS: Vigs - you wrote "There might be something wrong with the file. The bootloader is not accepting it due to failed
authentication. Be aware that when updating, you won't see the baseband version as UVUEMK2. You'll see the old MDL one.
Yes I have tried the Modem.bin file from 3 sources and the file
is fine. I know I wont see baseband as MK2, but that's not my issue mate. The flash FAILS.
.
Click to expand...
Click to collapse
I know you're only flashing the modem. But is it just in is raw form or is it tarred? The modem bin needs to be tarred. And from your screen shot, because I can't remember off the top of my head if Odin shows the tar ext when loaded, it looks like you are just loading the actual bin file and not tarred

Since I have the exact problem I thought I'd chime in too. The problem seems to be in the response from the bootloader. That is the step which my flashing stops as well. I have followed all steps and in all the posts very carefully and it is simply not the problem.
I am just wondering what the response from the bootloader have to be for that step to be completed successfully!
I am on stock 4.2.2 I only have it rooted so still looking for some solution for the modem to be able to update 4.3 as the op!
Sent from my Nexus 7 using Tapatalk

alextop30 said:
Since I have the exact problem I thought I'd chime in too. The problem seems to be in the response from the bootloader. That is the step which my flashing stops as well. I have followed all steps and in all the posts very carefully and it is simply not the problem.
I am just wondering what the response from the bootloader have to be for that step to be completed successfully!
I am on stock 4.2.2 I only have it rooted so still looking for some solution for the modem to be able to update 4.3 as the op!
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Try mobile Odin. I was able to bypass the checks and flash i9505 modems a while back.
Sent from my SGH-M919 using Tapatalk

re: TAR files.
ShinySide said:
I know you're only flashing the modem. But is it just in is raw form or is it tarred? The modem bin needs to be tarred. And from your screen shot, because I can't remember off the top of my head if Odin shows the tar ext when loaded, it looks like you are just loading the actual bin file and not tarred
Click to expand...
Click to collapse
The actual MODEM.BIN file is what needs to be loaded into Odin's "PHONE" tab/slot.
It should also work if it's a TAR file but it's best to flash it as modem.bin, that way there
is less of a chance of having a TAR file which might be or become corrupt.
The nice part about TAR or ZIP files is that we can flash multiple files in one flashing.
But if there is only one file which needs to be flashed (modem.bin) it's always best just
to flash the one file without adding compression or other changes to it.
TAR files are similar to ZIP files, they compress whatever files are inside of them
to a smaller size, but in doing so there is more of a chance that the file inside the TAR
or ZIP getting corrupted.
That's why I simply posted the modem.bin to be used by Odin, less chance of problems.

.
Hey MisterJunky,
Yes I was pretty certain that modem.bin does NOT need to be tar'd or zipped, so you also confirmed this.
Well that then leads us to a DEAD END. Since I am doing it EXACTLY the way you discribe it (with Modem.bin)
I don't know what else could be wrong. You quoted / replied to Shinyside's theory which is fine, but didn't
really reply to my thoughts .... I was wondering if it could be a issue with my ROM which is a 4.3 ROM. Although I think it doesn't matter .. ?
Thibor69 said:
I think the only difference is that I am running a different ROM than you mention, but you do say:
1) You can Odin flash the MK2 modem.bin while on any Jellybean Touchwiz 4.2.2 based rom
2) Or ODIN flash it after flashing the Infamous v9, Wicked v9.1, or any M919 MK2 JB based
Touchwiz 4.3 roms. Either way it makes no difference.
Now since I am running DARTHSTALKER S4 ☆ | VERSION X1 | Aroma | Multi-Carrier | 12.29.2013
( This ROM Is Based On The T-Mobile UVUEMK2 4.3 Base )
Option #1) does not apply to me ... BUT ... option #2) DOES apply to me and this ROM since DarthStalker is 4.3 based.
So I should be able to just Odin flash Modem.bin via your steps correct ?? Or am I wrong ?
Click to expand...
Click to collapse
ALSO ... just so you all know. Mobile Odin DOES NOT RUN on a USA T-Mobile Galaxy 4 phone. Mobile Odin has documented this fact.
Any other suggestions guys ????
Thank you
Misterjunky said:
The actual MODEM.BIN file is what needs to be loaded into Odin's "PHONE" tab/slot.
It should also work if it's a TAR file but it's best to flash it as modem.bin, that way there
is less of a chance of having a TAR file which might be or become corrupt.
The nice part about TAR or ZIP files is that we can flash multiple files in one flashing.
But if there is only one file which needs to be flashed (modem.bin) it's always best just
to flash the one file without adding compression or other changes to it.
TAR files are similar to ZIP files, they compress whatever files are inside of them
to a smaller size, but in doing so there is more of a chance that the file inside the TAR
or ZIP getting corrupted.
That's why I simply posted the modem.bin to be used by Odin, less chance of problems.
Click to expand...
Click to collapse

Yeah I've never heard of anyone not taring items for Odin. Weird but if it works it works.
Sent from my SGH-M919 using Tapatalk
---------- Post added at 04:09 AM ---------- Previous post was at 04:07 AM ----------
Thibor69 said:
.
Hey MisterJunky,
Yes I was pretty certain that modem.bin does NOT need to be tar'd or zipped, so you also confirmed this.
Well that then leads us to a DEAD END. Since I am doing it EXACTLY the way you discribe it (with Modem.bin)
I don't know what else could be wrong. You quoted / replied to Shinyside's theory which is fine, but didn't
really reply to my thoughts .... I was wondering if it could be a issue with my ROM which is a 4.3 ROM. Although I think it doesn't matter .. ?
ALSO ... just so you all know. Mobile Odin DOES NOT RUN on a USA T-Mobile Galaxy 4 phone. Mobile Odin has documented this fact.
Any other suggestions guys ????
Thank you
Click to expand...
Click to collapse
It's your bootloader rejecting it.
Do you have mobile Odin? It actually skips or over rides or doesn't get stopped by the bootloader verification.
Sent from my SGH-M919 using Tapatalk

Thibor69 said:
I am having trouble updating my modem to the new MK2. I have tried several times following the instructions
found in various places here on XDA, but nothing works.
_________________________________________________
Phone: SGH-M919 ( Galaxy 4 )
Carrier: T-Mobile LTE
Location: Phoenix
Custom ROM: DARTHSTALKER S4 v.X1 (MK2 & MDL Compliant)
Android version: 4.3 <<<<---- Is this a problem Im on 4.3 ?
Baseband: M919UVUAMDL
Kernel: 3.4.0-g4fe9989-dirty.joy23 #1
SELinux status: Permissive
This is what I am doing to try to update modem.....
1. Open Odin on PC (Mobile Odin doesn't run on G4 T-Mobile.LTE USA)
2. Uncheck Auto-Reboot / Load Modem.bin in the phone tab
3. Boot the phone into Download Mode via power & vol down
4. Plug USB into PC and PHONE
5. I see the BIG GREEN DROID
In the upper left corner of the phone, in tiny font it says:
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
Back on Odin now.....
The ID:COM tab in Odin turns blue and looks good to go. I click on "START".
The bar above ID:COM slowly fills with green. BUT when it is finished, the box above the ID:COM
turns RED and says FAILED !!.
### SEE PICTURE BELLOW ###
Back on the phone the tiny print in the upper left corner now says:
ODIN MODE
PRODUCT NAME: SGH-M919
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
CSB-OEM_CONFIG_LSB: 0x30
WRITE PROTECTION: Enable
START [224,1440]
SECURE CHECK FAIL : NDN
Why is it failing ??? Is it because I am on a 4.3 ROM ?
Please help me ....
Thanks
.
Click to expand...
Click to collapse
I've already posted a possible solution on my thread, but just in case, I'll repost it here: "Hm...I'm going to guess that it's maybe the Odin version that's affecting it? Here, try flashing using this version of Odin here: http://www.mediafire.com/download/1ap3sg0e2215ga6/Odin3.rar."

Thibor69 said:
.
Hey MisterJunky,
Yes I was pretty certain that modem.bin does NOT need to be tar'd or zipped, so you also confirmed this.
Well that then leads us to a DEAD END. Since I am doing it EXACTLY the way you discribe it (with Modem.bin)
I don't know what else could be wrong. You quoted / replied to Shinyside's theory which is fine, but didn't
really reply to my thoughts .... I was wondering if it could be a issue with my ROM which is a 4.3 ROM. Although I think it doesn't matter .. ?
ALSO ... just so you all know. Mobile Odin DOES NOT RUN on a USA T-Mobile Galaxy 4 phone. Mobile Odin has documented this fact.
Any other suggestions guys ????
Thank you
Click to expand...
Click to collapse
I just checked the supported devices of Mobile Odin in the thread by Chainfire and it seems that the SGH - M919 - which is the T-Mobile variant of the galaxy s4 is supported http://forum.xda-developers.com/showthread.php?t=1347899
Can you please link the documentation that you cannot flash the modem using that tool - I just want to read it before I go flash something again and end up softbricking my device.
As for my comment that pertains to the rest of the post - I just cannot understand how it worked for so many people using Odin from your computer and now it seems like it just does not flash for anyone that has recently attempted to update the modems!

re: try this.
alextop30 said:
I just checked the supported devices of Mobile Odin in the thread by Chainfire and it seems that the SGH - M919 - which is the T-Mobile variant of the galaxy s4 is supported http://forum.xda-developers.com/showthread.php?t=1347899
Can you please link the documentation that you cannot flash the modem using that tool - I just want to read it before I go flash something again and end up softbricking my device.
As for my comment that pertains to the rest of the post - I just cannot understand how it worked for so many people using Odin from your computer and now it seems like it just does not flash for anyone that has recently attempted to update the modems!
Click to expand...
Click to collapse
Why not try this, but before you do if you have a working rom in your phone right now
be sure to make a nandroid backup in recovery before trying the following:
Go into recovery and do a "Factory Reset" and wipe data/cache/system/dalvik cache.
Then shut down the phone, wait 20 seconds or so after shutting it down and boot back
up into Download mode and try Odin again...............
There is a 50/50 chance it will work.
Good luck!

alextop30 said:
I just checked the supported devices of Mobile Odin in the thread by Chainfire and it seems that the SGH - M919 - which is the T-Mobile variant of the galaxy s4 is supported http://forum.xda-developers.com/showthread.php?t=1347899
Can you please link the documentation that you cannot flash the modem using that tool - I just want to read it before I go flash something again and end up softbricking my device.
Click to expand...
Click to collapse
Huh .... I bought the app last night and returned for a refund, BUT this looks like a newer version then the one I had... allthough the update of Mobile Odin is from Nov. it looks like a different version ... how can that be. ANyway I will try this version tomorrow and let you know if it fails .... Thank you !!
Hi Shiamatsu -
Thank you for the link to that version of PC Odin. I will try that in the morning also.
I follow your post ... sorry I missed that !! Thanks
Hi MisterJunky -
Thanks for the idea. I will try that as my final attempt if the above 2 things dont work out for me.
Thanks all !!!!

alextop30 said:
I just checked the supported devices of Mobile Odin in the thread by Chainfire and it seems that the SGH - M919 - which is the T-Mobile variant of the galaxy s4 is supported http://forum.xda-developers.com/showthread.php?t=1347899
Can you please link the documentation that you cannot flash the modem using that tool - I just want to read it before I go flash something again and end up softbricking my device.
Click to expand...
Click to collapse
Well I guess it is not the phone that wont run Odin, but seems that Odin Mobile Pro does not like Android 4.3
### SEE PICTURE ####
I am now searching for a FlashKernel for this phone.
Need FlashKernel for T-Mobile SGH-M919 running on Android 4.3 ROM. If you happen to find one, please share !!!! )
ThaNKS

shiamatsu said:
I've already posted a possible solution on my thread, but just in case, I'll repost it here: "Hm...I'm going to guess that it's maybe the Odin version that's affecting it? Here, try flashing using this version of Odin here: http://www.mediafire.com/download/1ap3sg0e2215ga6/Odin3.rar."
Click to expand...
Click to collapse
Thanks but sorry it is still a NO GO with that version of ODIN.

Alright before flashing the MK2 modem via Download Mode, try resetting the binary counter using an app called Triangle Away (its located here on xda developers). Once you install the app, please follow the instructions given. You need to be on a TouchWiz rom with a stock Samsung kernel (best way is to Odin to stock 4.2.2 MDL). This is something that I read from Chainfire's Google+ page which may be the solution:
"Still, the binary status needs to be official and the counter 0 on recent bootloaders if you want to do fun things like flash modems with for example Mobile ODIN (update coming as well). Otherwise the bootloader will mark those regions of the flash storage as protected, and they cannot be written to (causing freezes and whatnot)."
Give it a try and see what happens. The 4.2.2 bootloader isn't recent. But, who knows?

Thibor69 did resetting the counter work to flash the modem successfully?
Sent from my Nexus 7 using Tapatalk