Related
CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Did u flash the kernel for the ROM u flashed ? The ROM will not boot without its kernel.
Sent from my Xperia Arc S using Tapatalk 2
mtpocketz said:
CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Click to expand...
Click to collapse
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Thanks
iwarind said:
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Click to expand...
Click to collapse
Got it - Yes i was installing CWM within stock rom via market. though i tried to install it through adb/windows but still i guess the problem was all about not installing a custom recovery kernel.
Thanks a lot !
Installation aborted error status 7 xperia mini
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
aditya naik said:
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
Click to expand...
Click to collapse
Download stock ROM and install it via Flashtool.
My signature, there is link to download stock ROMs. Search for proper one and install it.
Hello,
Today i rooted my Galaxy grand with CWM using Odin and intalled SuperSu through recovery mode. Then i entered recovery mode again to install Xperia Z rom for Galaxy Grand , which i had placed in my external sd card. When i installed it using all the steps(Wipe data,cache etc etc) and reeboted my device, it got stuck on the boot screen with Samsung Galaxy grand logo running in loop for several time. Atlast i removed my battery and using the download mode again installed the 4.2.2 update with Odin.
Can u please tell me what went wrong while installing the rom.
nish1991 said:
Hello,
Today i rooted my Galaxy grand with CWM using Odin and intalled SuperSu through recovery mode. Then i entered recovery mode again to install Xperia Z rom for Galaxy Grand , which i had placed in my external sd card. When i installed it using all the steps(Wipe data,cache etc etc) and reeboted my device, it got stuck on the boot screen with Samsung Galaxy grand logo running in loop for several time. Atlast i removed my battery and using the download mode again installed the 4.2.2 update with Odin.
Can u please tell me what went wrong while installing the rom.
Click to expand...
Click to collapse
Maybe your source file is corrupted? In CWM, after installing the ROM, does it appears installation success or update success any similar message?
And suggest you wipe data & cache after installing the ROM, not before. Wipe Dalvik cache too.
soralz said:
Maybe your source file is corrupted? In CWM, after installing the ROM, does it appears installation success or update success any similar message?
And suggest you wipe data & cache after installing the ROM, not before. Wipe Dalvik cache too.
Click to expand...
Click to collapse
Source file? Are you speaking about the rom file I downloaded ?
Yes after installing the rom there is message Updated Successfully in CWM.
But i wiped the data and cache before installing the rom and dalvik cache after installing the rom..
Please help....can you give me detailed steps for installing rom.
If you are coming from stock rom after it shows installation complete again wipe all DATA frm cwm and reboot
Sent from my GT-I9505 using Tapatalk 2
Sulaimanshariff said:
If you are coming from stock rom after it shows installation complete again wipe all DATA frm cwm and reboot
Sent from my GT-I9505 using Tapatalk 2
Click to expand...
Click to collapse
Hey no worries...
I just installed another Xperia Z rom...and everything is grt nw....
Same Problem it is stucked now on that sceen and I too got the massage that it is install successfully... I cant install any other ROM as I want to use dual sim and most of the ROM are not compatible with dual SIM.... PLEASE HELP
soralz said:
Maybe your source file is corrupted? In CWM, after installing the ROM, does it appears installation success or update success any similar message?
And suggest you wipe data & cache after installing the ROM, not before. Wipe Dalvik cache too.
Click to expand...
Click to collapse
nish1991 said:
Hello,
Today i rooted my Galaxy grand with CWM using Odin and intalled SuperSu through recovery mode. Then i entered recovery mode again to install Xperia Z rom for Galaxy Grand , which i had placed in my external sd card. When i installed it using all the steps(Wipe data,cache etc etc) and reeboted my device, it got stuck on the boot screen with Samsung Galaxy grand logo running in loop for several time. Atlast i removed my battery and using the download mode again installed the 4.2.2 update with Odin.
Can u please tell me what went wrong while installing the rom.
Click to expand...
Click to collapse
"Atlast i removed my battery and using the download mode again installed the 4.2.2 update with Odin."
can you tell me how you did?? i am a newbie
stuck in boot loop
soralz said:
Maybe your source file is corrupted? In CWM, after installing the ROM, does it appears installation success or update success any similar message?
And suggest you wipe data & cache after installing the ROM, not before. Wipe Dalvik cache too.
Click to expand...
Click to collapse
yes everything went right but after i click reboot than i try to start samsung galaxy grand i9082 logo appears there it blink 4 5 times then i remove my battery and try to start again but now it is not even opening not cwm recovery menu and not going to the odin download mod also
ODIN mode is also not opening without usb cavle mean opening when plugged into charging.
please help me ,-_-,
, ,
Xperia Z Rom GT-I9082
Which CWM i recovery i use please tell me
i'm using CWM 6.0.2 recovery but when try to install i stuck in installing screen and then automatically back in recovery mode.
MD5 not found
yogeshp007 said:
Which CWM i recovery i use please tell me
i'm using CWM 6.0.2 recovery but when try to install i stuck in installing screen and then automatically back in recovery mode.
MD5 not found
Click to expand...
Click to collapse
Ik think that the CWM version is to old.
Also if you want to go to lollipop later then you can't do this with CWM 6.0.2.
Download a new CWM with an minimum version 6.4.5 or TWRP 2.8.6.0.
Never tried to install the older version roms with TWRP but with CWM I was able to install all.
Installing Rom
Sir i want to install xperia z rom please help me!!
tell me in details please
Hello everyone,
I decided today to try and switch from aokp android 4.4.2 rom back to the official 4.3 update. I Factory reset and cleared cache, and then flashed the .tar file via odin, and it said it passed. Unfortunately, it gets to the flashing Samsung logo, and gets stuck there.. any suggestions on how to fix this?
deanfranks21 said:
Hello everyone,
I decided today to try and switch from aokp android 4.4.2 rom back to the official 4.3 update. I Factory reset and cleared cache, and then flashed the .tar file via odin, and it said it passed. Unfortunately, it gets to the flashing Samsung logo, and gets stuck there.. any suggestions on how to fix this?
Click to expand...
Click to collapse
What phone model and carrier do you use and where did you find an Odin flashable file for 4.3 JB? Do you have custom recovery installed on your phone?
Larry2999 said:
What phone model and carrier do you use and where did you find an Odin flashable file for 4.3 JB? Do you have custom recovery installed on your phone?
Click to expand...
Click to collapse
I have a bell SGH-I747M, I got the zip off of sam mobile, and I did, until I flashed the rom through Odin and it removed root and cwm
deanfranks21 said:
I have a bell SGH-I747M, I got the zip off of sam mobile, and I did, until I flashed the rom through Odin and it removed root and cwm
Click to expand...
Click to collapse
The 4.3 ROM would have been better flashed as a zip file via custom recovery than Odin. I would suggest you first try booting into recovery mode and doing a hard wipe/reset. If this does not work, then you may try reinstalling the zip. Boot into download mode and flash custom recovery (cwm or TWRP) via Odin. Also copy the zip file you earlier downloaded (unextracted) onto an SDHC card or you may try another download via this link <http://www.androidfilehost.com/?fid=23269279319199494>. If you are able to successfully flash custom recovery, don't allow the phone to reboot but remove the battery and insert the card. Then boot into custom recovery and flash the zip from the SDHC card. Clear the cache and reset and, hopefully, your phone will be back in business.
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Maybe it's a bad download or try flashing philz cmw then do clean install to flash a new rom then flash any rom
Brought to you by SM-T210R
Ripshock said:
Maybe it's a bad download or try flashing philz cmw then do clean install to flash a new rom then flash any rom
Brought to you by SM-T210R
Click to expand...
Click to collapse
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
brajesh0201 said:
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
Click to expand...
Click to collapse
Is your device rooted?
Brought to you by SM-T210R
Ripshock said:
Is your device rooted?
Brought to you by SM-T210R
Click to expand...
Click to collapse
yes rooted ,
brajesh0201 said:
yes rooted ,
Click to expand...
Click to collapse
Android-armeabi.universial-root.zip used this package to root
brajesh0201 said:
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
Click to expand...
Click to collapse
Have you make a backup befor you flashed The Rom?
For this Rom you need always The newest Recovery Version,depent of New updater script.
Can you go to The recovery , make a factory reset and wipe cache / dalvik.
Then go to download mode and flash Stockrom again.
Then flash Philz recovery, after flash Boot manuly into recovery make an backup and now reboot your Tab Into recovery make an fullwipe and flash your New Customrom.
bierma32 said:
Have you make a backup befor you flashed The Rom?
For this Rom you need always The newest Recovery Version,depent of New updater script.
Can you go to The recovery , make a factory reset and wipe cache / dalvik.
Then go to download mode and flash Stockrom again.
Then flash Philz recovery, after flash Boot manuly into recovery make an backup and now reboot your Tab Into recovery make an fullwipe and flash your New Customrom.
Click to expand...
Click to collapse
I tried the above method , no luck
if i flash stock firmware i stuck with an samsung logo and if i flash custom rom i stuck with an android boot image ...
i am not able to wipe in PhilZ recovery i am getting the error cannot mount /data and cannot mount /data/.androidsecure
brajesh0201 said:
I tried the above method , no luck
if i flash stock firmware i stuck with an samsung logo and if i flash custom rom i stuck with an android boot image ...
i am not able to wipe in PhilZ recovery i am getting the error cannot mount /data and cannot mount /data/.androidsecure
Click to expand...
Click to collapse
Im using philz tuoch and i habe no prob.
At philz have check The Mount point (sdcard or sdcard/0 )
If these all not hell flash CWM.
I have no clue what i did with it, but this is on the screen:
Odin Mode
Product name: SM-T210
Current Binary: Custom
System Status: Custon
HW REV: 0x5
It has an image like: Tablet......Yellow triagle with an ! in it.....Computer.
Under that it has the text: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. But Kies can't connect to the device. I have no clue what i did all ....
Experts please help !!!
hey
in philz recovery, in wipe options select - clean to install new rom
the goto tab 3 7.0 area get svelte rom , you need to put it on removable microsd with card reader [get one]
the put card back in tab reboot to recovery and flash, firmware updates aren't always good or necessary,
odin should be a last option. stay calm [use the force] and good luck :good:
brajesh0201 said:
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Click to expand...
Click to collapse
here is the solution of your prob, i font it in the lt02 Thread
bierma32
Post#352 and following Posts.
http://forum.xda-developers.com/showthread.php?p=53154386
Quote:
Originally Posted by*jstath1972*
In the first attempt i made a dalvik cache, cache, system wiping. I installed the rom and made again a dalvik cache, cache wiping and reboot. Then was saying "no Root. Would you like to flash super user in to system?" and then nothing. I made re install for second time the same rom zip with the default "Factory Reset" and everything went fine. Weird ha ? I also use TWRP 2.7.0.0 .*
I hope to help.*
Its funny its only work when you factory reset, My guess would be that something wrong with twrp or updater script.*
Maybe @gr8nole*will know more bout this issue.*
Sent from my Galaxy Nexus using Tapatalk
brajesh0201 said:
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Click to expand...
Click to collapse
try to flash the stock ROM Android 4.1.2 ( Jellybean ) from page www.sammobile.com and flash it with odin 3.07 , after you flash with odin sees the recovery of stock and give ' Wipe Data / Factory Reset ' ' and the problem is solved ( I run my me :good: ) and sorry for my bad English that use a translator :silly:
( and the solution suddenly discovered )
I just hope it works for you you too
So i recently installed TWRP version 3.0.0-0 and i wan to get out of it but when i reboot it it jus goes back to TWRP instead of booting into my device if you know how to fix it please help
It seems that you have uninstalled your rom.
how did you flash twrp and what's your rom?
darknessd31 said:
It seems that you have uninstalled your rom.
how did you flash twrp and what's your rom?
Click to expand...
Click to collapse
I Used Flasify to get TWRP and i was trying to get Cyanegen Mod
did you wipe anything?
flash with Odin your samsung firmware stock.
if you want cm13 download it from their website
put it in your memory
go to twrp (it is better to install it again with odin )
wipe system,cache,data
install cm13 and gapps
have fun
**becareful you should download your device specefic rom
darknessd31 said:
if you want cm13 download it from their website
put it in your memory
go to twrp (it is better to install it again with odin )
wipe system,cache,data
install cm13 and gapps
have fun
**becareful you should download your device specefic rom
Click to expand...
Click to collapse
I reinstalled the rom so every thing is fine
darknessd31 said:
did you wipe anything?
Click to expand...
Click to collapse
No But i reflashed the rom and everything in fine now