Trying to see if a list is around somewhere for these codes and if any of them can be useful without causing damage. I have been searching and only found a couple here and there. I assume they are specific to a particular model Samsung device or are they universal? Thanks.
I have the full list, will post later tonight.
Sent from my SGH-T989 using XDA App
Would like it too
Sent from my SGH-T989 using xda premium
I want it also!
Attached are the device codes for Samsung, HTC, and Windows phones. ENJOY!!!!!!
Awesome thanks!!
what is the code to check the hidden info like if the "Recondition" is on or off for samsung T989? Thanks.
Thank you!
Download "SGS Secret Codes", "SGS Toobox", etc from Market.
It does't have all the codes, but easier since you can just select from the list instead of typing in.
If you don't want to open the file..
*#1234# (View SW Version PDA, CSC, MODEM)
*#12580*369# (SW & HW Info)
*#197328640# (Service Mode)
*#0228# (ADC Reading)
*#32489# (Ciphering Info)
*#232337# (Bluetooth Address)
*#232331# (Bluetooth Test Mode)
*#232338# (WLAN MAC Address)
*#232339# (WLAN Test Mode)
*#0842# (Vibra Motor Test Mode)
*#0782# (Real Time Clock Test)
*#0673# (Audio Test Mode)
*#0*# (General Test Mode)
*#2263# (RF Band Selection)
*#9090# (Diagnostic ConfiguratioN)
*#7284# (USB I2C Mode Control)
*#872564# (USB Logging Control)
*#4238378# (GCF Configuration)
*#0283# (Audio Loopback Control)
*#1575# (GPS Control Menu)
*#3214789650# (LBS Test Mode)
*#745# (RIL Dump Menu)
*#746# (Debug Dump Menu)
*#9900# (System Dump Mode)
*#44336# (Sofware Version Info)
*#7780# (Factory Reset)
*2767*3855# (Full Factory Reset)
*#0289# (Melody Test Mode)
*#2663# (TSP / TSK firmware update)
*#03# (NAND Flash S/N)
*#0589# (Light Sensor Test Mode)
*#0588# (Proximity Sensor Test Mode)
*#273283*255*3282*# (Data Create Menu)
*#273283*255*663282*# (Data Create SD Card)
*#3282*727336*# (Data Usage Status)
*#7594# (Remap Shutdown to End Call TSK)
*#34971539# (Camera Firmware Update)
*#526# (WLAN Engineering Mode)
*#528# (WLAN Engineering Mode)
*#7412365# (Camera Firmware Menu)
*#80# (Unknown)
*#07# (Test History)
*#3214789# (GCF Mode Status)
*#272886# (Auto Answer Selection)
*#8736364# (OTA Update Menu)
*#301279# (HSDPA/HSUPA Control Menu)
*#7353# (Quick Test Menu)
*2767*4387264636# (Sellout SMS / PCODE view)
*#7465625# (View Phone Lock Status)
*7465625*638*# (Configure Network Lock MCC/MNC)
#7465625*638*# (Insert Network Lock Keycode)
*7465625*782*# (Configure Network Lock NSP)
#7465625*782*# (Insert Partitial Network Lock Keycode)
*7465625*77*# (Insert Network Lock Keycode SP)
#7465625*77*# (Insert Operator Lock Keycode)
*7465625*27*# (Insert Network Lock Keycode NSP/CP)
#7465625*27*# (Insert Content Provider Keycode)
*#272*imei#* (Product code)
Reserved...
Is there a code that would allow us to the change the speaker gain in order to make it louder. I remember doing that with the samsung eternity . Yes I realize that was years ago and not even Android lol. Just curious
Sent from my SGH-T989 using XDA App
msmith1991 said:
Is there a code that would allow us to the change the speaker gain in order to make it louder. I remember doing that with the samsung eternity . Yes I realize that was years ago and not even Android lol. Just curious
Sent from my SGH-T989 using XDA App
Click to expand...
Click to collapse
This may not be the way you want to accomplish this, but, there is an app in the Market called "Volume+ FREE" by a developer named Meltus. I've been using this to raise my external speaker volume and a lot more. Great app and the settings stick until you change them again if you are worried about rebooting.
I have always has the problem that my device will be about 4 degree off set to the left when I hold it portrait, so I've been searching for a way to calibrate our g-sensor but end up with nothing found. It also turns out that galaxy nexus didn't have any option to calibrate g-sensor onboard, so the only thing I can do is to open this topic and see if anybody can give any advice. Any help will be appreciated.
Sent from my Galaxy Nexus using xda premium
Haven't found a way either...compass calibration seems to work for a little bit but resets itself. Calibrate compass by rotating phone twice along each of its three axis
Hope more people will look into this.
Sent from my Galaxy Nexus using xda premium
Maybe there is an hidden menu for it? Even the iPhone has the abillity to calibrate...so why Android should not have it, too?
Or should it calibrate it self?
Blacksceada said:
Maybe there is an hidden menu for it? Even the iPhone has the abillity to calibrate...so why Android should not have it, too?
Or should it calibrate it self?
Click to expand...
Click to collapse
Really? I'm not even aware that iPhone has such function. Maybe that's because my 4s has always been OK.
Sent from my Galaxy Nexus using xda premium
I have the same problem with my Galaxy Nexus. There is no option to calibrate the G-sensor and I've looked everywhere. I was trying to play temple run and the sensor is all messed up so I cannot play it.
Same issue here, was just about to post a thread before seeing this, ask one of the devs perhaps?
Maybe a MOD could sticky this?
Problem as seen in attached screen shot, when phone is place upright, the plumb line is off
I know this sounds silly, but have either of you tried turning the phone off, placing it on a flat surface, and then starting up the phone while not touching or moving it until it's fully rebooted?
I would image since there's no calibration settings in the menu, it's performing some kind of calibration while starting...? Anyone?
Also, there are several compass and leveling apps in the market that provide the option to calibrate.
I just tried rebooting it on a flat surface but nope, problem still persists.
Apps on the play store do calibrate but its only app specific and not system wide. so a bubble line app may be calibrated but when using any other apps it goes back to the default calibrations.
I might be wrong... but I thought I remember reading somewhere about a hidden menu that had an option to calibrate it. It was something like #282828, or something similar. I could be wrong, I just faintly remember.
Sent from my Galaxy Nexus using Tapatalk 2
jdec529 said:
I might be wrong... but I thought I remember reading somewhere about a hidden menu that had an option to calibrate it. It was something like #282828, or something similar. I could be wrong, I just faintly remember.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
So far what I have found is a hidden menu for gtalk service. But nothing else. Problem still not solved.
Sent from my Galaxy Nexus using xda premium
Android has no global calibration system. Every app/game author needs to implement calibration on its own. Talk about wasting resources.. Thanks, Google.
Sent from my Galaxy Nexus using Tapatalk 2
zapek666 said:
Android has no global calibration system. Every app/game author needs to implement calibration on its own. Talk about wasting resources.. Thanks, Google.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
Even my Galaxy S II upgraded to Android 4.0 it still give me the ability to calibrate the sensors, so I still believe there has to be a way to do so...
Sent from my Galaxy Nexus using xda premium
This is quite old but most of these still work (it's a Samsung thing).
Software version: *#9999#
IMEI number: *#06#
Serial number: *#0001#
Battery status- Memory capacity : *#9998*246#
Debug screen: *#9998*324# - *#8999*324#
LCD kontrast: *#9998*523#
Vibration test: *#9998*842# - *#8999*842#
Alarm beeper - Ringtone test : *#9998*289# - *#8999*289#
Smiley: *#9125#
Software version: *#0837#
Display contrast: *#0523# - *#8999*523#
Battery info: *#0228# or *#8999*228#
Display storage capacity: *#8999*636#
Display SIM card information: *#8999*778#
Show date and alarm clock: *#8999*782#
The display during warning: *#8999*786#
Samsung hardware version: *#8999*837#
Show network information: *#8999*638#
Display received channel number and received intensity: *#8999*9266#
*#1111# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions Together
*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error LOG Menu
*#8999*327# EEP Menu
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC Adress
*#5282837# Java Version
Type in *#0000# on a Samsung A300 to reset the language
Master reset(unlock) #*7337# (for the new samsungs E700 x600 but not E710)
Samsung E700 type *#2255# to show secret call log (not tested)
Samsung A300, A800 phone unlock enter this *2767*637#
Samsung V200, S100, S300 phone unlock : *2767*782257378#
#*4773# Incremental Redundancy
#*7785# Reset wakeup & RTK timer cariables/variables
#*7200# Tone Generator Mute
#*3888# BLUETOOTH Test mode
#*7828# Task screen
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*2565# No Blocking? General Defense.
#*3353# General Defense, Code Erased.
#*3837# Phone Hangs on White screen.
#*3849# Restarts Phone
#*7337# Restarts Phone (Resets Wap Settings)
#*2886# AutoAnswer ON/OFF
#*7288# GPRS Detached/Attached
#*7287# GPRS Attached
#*7666# White Screen
#*7693# Sleep Deactivate/Activate
#*2286# Databattery
#*2527# GPRS switching set to (Class 4, 8, 9, 10)
#*2679# Copycat feature Activa/Deactivate
#*3940# External looptest 9600 bps
#*4263# Handsfree mode Activate/Deactivate
#*2558# Time ON
#*3941# External looptest 115200 bps
#*5176# L1 Sleep
#*7462# SIM Phase
#*7983# Voltage/Freq
#*7986# Voltage
#*8466# Old Time
#*2255# Call Failed
#*5376# DELETE ALL SMS!!!!
#*6837# Official Software Version: (0003000016000702)
#*2337# Permanent Registration Beep
#*2474# Charging Duration
#*2834# Audio Path (Handsfree)
#*3270# DCS Support Activate/Deactivate
#*3282# Data Activate/Deactivate
#*3476# EGSM Activate/Deactivate
#*3676# FORMAT FLASH VOLUME!!!
#*4760# GSM Activate/Deactivate
#*4864# White Screen
#*7326# Accessory
#*7683# Sleep variable
#*3797# Blinks 3D030300 in RED
#*7372# Resetting the time to DPB variables
#*3273# EGPRS multislot (Class 4, 8, 9, 10)
#*7722# RLC bitmap compression Activate/Deactivate
#*2351# Blinks 1347E201 in RED
#*2775# Switch to 2 inner speaker
#*7878# FirstStartup (0=NO, 1=YES)
#*3838# Blinks 3D030300 in RED
#*2077# GPRS Switch
#*2027# GPRS Switch
#*0227# GPRS Switch
#*0277# GPRS Switch
#*22671# AMR REC START
#*22672# Stop AMR REC (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# Pause REC
#*22674# Resume REC
#*22675# AMR Playback
#*22676# AMR Stop Play
#*22677# Pause Play
#*22678# Resume Play
#*77261# PCM Rec Req
#*77262# Stop PCM Rec
#*77263# PCM Playback
#*77264# PCM Stop Play
#*22679# AMR Get Time
*#8999*364# Watchdog ON/OFF
*#8999*427# WATCHDOG signal route setup
*2767*3855# = Full Reset (Caution every stored data will be deleted.)
*2767*2878# = Custom Reset
*2767*927# = Wap Reset
*2767*226372# = Camera Reset (deletes photos)
*2767*688# Reset Mobile TV
#7263867# = RAM Dump (On or Off)
*2767*49927# = Germany WAP Settings
*2767*44927# = UK WAP Settings
*2767*31927# = Netherlands WAP Settings
*2767*420927# = Czech WAP Settings
*2767*43927# = Austria WAP Settings
*2767*39927# = Italy WAP Settings
*2767*33927# = France WAP Settings
*2767*351927# = Portugal WAP Settings
*2767*34927# = Spain WAP Settings
*2767*46927# = Sweden WAP Settings
*2767*380927# = Ukraine WAP Settings
*2767*7927# = Russia WAP Settings
*2767*30927# = GREECE WAP Settings
*2767*73738927# = WAP Settings Reset
*2767*49667# = Germany MMS Settings
*2767*44667# = UK MMS Settings
*2767*31667# = Netherlands MMS Settings
*2767*420667# = Czech MMS Settings
*2767*43667# = Austria MMS Settings
*2767*39667# = Italy MMS Settings
*2767*33667# = France MMS Settings
*2767*351667# = Portugal MMS Settings
*2767*34667# = Spain MMS Settings
*2767*46667# = Sweden MMS Settings
*2767*380667# = Ukraine MMS Settings
*2767*7667#. = Russia MMS Settings
*2767*30667# = GREECE MMS Settings
*#7465625# = Check the phone lock status
*7465625*638*Code# = Enables Network lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*27*Code# = Disables CP lock
*7465625*746*Code# = Enables SIM lock
#7465625*746*Code# = Disables SIM lock
*7465625*228# = Activa lock ON
#7465625*228# = Activa lock OFF
*7465625*28638# = Auto Network lock ON
#7465625*28638# = Auto Network lock OFF
*7465625*28782# = Auto subset lock ON
#7465625*28782# = Auto subset lock OFF
*7465625*2877# = Auto SP lock ON
#7465625*2877# = Auto SP lock OFF
*7465625*2827# = Auto CP lock ON
#7465625*2827# = Auto CP lock OFF
*7465625*28746# = Auto SIM lock ON
#7465625*28746# = Auto SIM lock OFF
Type *#9998*627837793# Go to the 'my parameters' and there you will find new menu where you can unlock phone.(not tested-for
samsung C100)
To unlock a Samsung turn the phone off take the sim card and type the following code *#pw+15853649247w# .
Java status code: #*53696# (Samsung X600)
If you want to unlock your phone put a sim from another company then type *#9998*3323# it will reset your phone. Push exit and then
push 7, it will reset again. Put your other sim in and it will say sim lock, type in 00000000 then it should be unlocked. Type in *0141#
then the green call batton and it's unlocked to all networks. This code may not work on the older phones and some of the newer phones.
If it doesn't work you will have to reset your phone without a sim in it by typing *#2767*2878# or *#9998*3855# (not tested)
I know that for the Samsung Eternity to get to the administrative menu type this in your dial pad,
*#6984125*#
Operator code for Pre-configuration
*#73561*# (probably won't need this)
And the Master Key is
*#3818790*#
Click to expand...
Click to collapse
n2ishun said:
This is quite old but most of these still work (it's a Samsung thing).
Click to expand...
Click to collapse
Thanks. I tried them out. Galaxy Nexus seemed not responding to codes ending without "#*#*", so most of them will not work.
Sent from my Galaxy Nexus using xda premium
jokies said:
Thanks. I tried them out. Galaxy Nexus seemed not responding to codes ending without "#*#*", so most of them will not work.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
For anybody who found this thread, I switched to a GT-I9300 to some how solve the problem...
Sent from my GT-I9300 using xda premium
lesbox said:
I know this sounds silly, but have either of you tried turning the phone off, placing it on a flat surface, and then starting up the phone while not touching or moving it until it's fully rebooted?
I would image since there's no calibration settings in the menu, it's performing some kind of calibration while starting...? Anyone?
Also, there are several compass and leveling apps in the market that provide the option to calibrate.
Click to expand...
Click to collapse
Apps only calibrate for themselves, not other apps.
And, yes, your idea is silly, since the device doesn't know it's location on a surface. What if you turn it while not lying flat? If your method would work, it would decalibrate most devices since they are not being turned on while lying flat.
jokies said:
For anybody who found this thread, I switched to a GT-I9300 to some how solve the problem...
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Because its *#*# ....#*#* the dots being the code. *#*#4636#*#* info menu as example.
I have seen a few postings mention this.
Dial *#197328640#
This brings up the debug screen (service mode)
I unlocked my T-mobile Samsung Galaxy S4 and I am trying to use it on an AT&T mnvo but I do not get any data service. So I am wondering if the bands need to be changed in this menu or some other menu on the phone?
Does anyone now this information? I am trying to determine the cause of no data on my Red Pocket sim card. I have the APN Settings correct and registered on the Network but still no data connection.
This is a discussion thread dealing with and related to
all of the Secret Codes for the Samsung Galaxy S4
Here you will find all of the official dial pad codes for
Samsung Galaxy S4 and other Samsung phones
Here is a complete listing of these codes:
----------------------------------------------------------------------
*#06# Shows IMEI (International Mobile Equipment Identity) number
*#0*# LCD Test Menu
Dial the secret code *#0*#. Now you get a screen with title LCD TEST as shown in image and
below that you have lots of option to test various hardware parts of your phone such as speaker, sensor, lcd, etc
*#8999*523# LCD Brightness
*#1234# To check Software and Hardware information, PDA, CSC, MODEM (Firmware Version)
*#2222# H/W Version
*#*#4636#*#* user statistics and Phone Info
*#0011# Displays status information for the GSM
*#7780# Factory Reset
*2767*3855# Full factory reset (Don’t dial unless you have problem, it does not ask you to confirm )
*#12580*369# SW & HW Info
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*5376# DELETE ALL SMS!!!!
*#197328640# Service Mode
*#0228# Battery status (ADC, RSSI reading)
*#32489# Service mode (Ciphering Info)
*#2255# Call List
#*3888# BLUETOOTH Test mode
#*7828# Task screen
*#5282837# Java Version
*#232337# Bluetooth MAC Adress
*#232331# Bluetooth Test Mode
*#232338# WLAN MAC Address
*#232339# WLAN Test Mode
*#8999*8378# Test Menu
*#0842# Vibra Motor Test Mode
*#0782# Real Time Clock Test
*#0673# Audio Test Mode
*#0*# General Test Mode
*#2263# RF Band Selection / Network modes select
*#9090# Diagnostic ConfiguratioN
*#7284# USB I2C Mode Control
*#872564# USB Logging Control
*#4238378# GCF Configuration
*#0283# Audio Loopback Control
*#1575# GPS Control Menu
*#3214789650# LBS Test Mode
*#745# RIL Dump Menu
*#746# Debug Dump Menu
*#9900# Takes you to System Dump, where Disabling Fast Dormancy gives a boost to your network
speed on some networks (both wifi and Gprs), same code to re-enable it
*#44336# Sofware Version Info
*#0289# Melody Test Mode
*#2663# TSP / TSK firmware update
*#03# NAND Flash S/N
*#0589# Light Sensor Test Mode
*#0588# Proximity Sensor Test Mode
*#273283*255*3282*# Data Create Menu
*#273283*255*663282*# Data Create SD Card
*#3282*727336*# Data Usage Status
*#7594# Remap Shutdown to End Call TSK
*#34971539# Camera Firmware Update
*#526# WLAN Engineering Mode
*#528# WLAN Engineering Mode
*#7412365# Camera Firmware Menu
*#07# Test History
*#3214789# GCF Mode Status
*#272886# Auto Answer Selection
*#8736364# OTA Update Menu
*#301279# HSDPA/HSUPA Control Menu
*#7353# Quick Test Menu
*2767*4387264636# Sellout SMS / PCODE view
*#7465625# View Phone Lock Status
*7465625*638*# Configure Network Lock MCC/MNC
#7465625*638*# Insert Network Lock Keycode
*7465625*782*# Configure Network Lock NSP
#7465625*782*# Insert Partitial Network Lock Keycode
*7465625*77*# Insert Network Lock Keycode SP
#7465625*77*# Insert Operator Lock Keycode
*7465625*27*# Insert Network Lock Keycode NSP/CP
#7465625*27*# Insert Content Provider Keycode
*#272*IMEI# then we will get buyer code (For samsung galaxy sIII csc code)
*#*#7780#*#* Factory data reset – Clears Google-account data, system and program
settings and installed programs. system will not be deleted, and OEM programs, as well
as My Documents (pictures, music, videos)
Feel free to post any questions or comments you may have relating to these codes.
Nice!!!!!
Sent from my GT-I9505G using Tapatalk
I've scoured the internet for finding out to enter the service menu on the note 7. It seems that the s7 and s7e have been figured out, but no one yet seems to have been able to actually enter the service mode the note 7.
I do know that the service mode application opens if one dials: *#0011#, but I cannot enter further into the application to change LTE bands and what not.
In past Samsung phones, one could further enter the service mode by hitting:
Menu -> back
Menu -> key input -> Q
Menu -> key input -> 0000
Wait 10 seconds
This method does NOT work on the note 7...
Now while this may be a larger issue, I cannot get AT&T LTE enabled on my device. I have the N930-FD from Singapore. This is why I'm trying to access this hidden menu.
On key input type in: Q0
And wait 10 secs.
Still not working.
While I follow the procedure, there is no response. It still display the network information.
What is the whole procedure to operate?
Did you have any finding regarding how to change LTE bands?
Does this work?
bands engineering screen *#2263#