Related
my lg f180k wont start anymore, y can acces download mode, y try to flas many kdz but after flash is complete my phone enter in bootloop , y can acces recovery but there seems to be a probelm because says "failed to mount/cache(invalid argument)", cant open/cache/recovery/last-log, and so on, y try to enter on sd card to aply another rom but there is 0 folder,, y can gest go back y dont have what to select in sd card no folder (seems phone dont reconize my sd card???). y try to aply update whit adb sideload, y manage to make conection whit phone and copy rom from pc to phone but when he arive at 100% progrees, phone says same story cant open/cache........
So if anybody could help me y will be very happy becauze y dont now what y can do now.
And pls excuze my bad eng.
you have PM
kimitza said:
you have PM [/QUOTE\
Thx for msg y send you back msg
Click to expand...
Click to collapse
Hi guys,
I accidently bricked my LG G8 (Amazon Version) while trying to root it.
I have no download mode and no QDLoader mode. Is there a way to get the 9008 mode ?
Thanks
This place isn't as lively as it once was. I miss the old XDA. Think we've gotten old. lol
I'm sorry. :c
leptdre said:
Hi guys,
I accidently bricked my LG G8 (Amazon Version) while trying to root it.
I have no download mode and no QDLoader mode. Is there a way to get the 9008 mode ?
Thanks
Click to expand...
Click to collapse
Were you able to get QDLoader 9008 mode in your Bricked LG G8 ?
I am facing the same issue in LG G8X. Could you help ?
jonny789 said:
Were you able to get QDLoader 9008 mode in your Bricked LG G8 ?
I am facing the same issue in LG G8X. Could you help ?
Click to expand...
Click to collapse
I did. It's a pain in the ass. I just had the usb cable in the computer attached to the phone, and hard reset via volume down and power. As soon as the screen goes off, I hammer on the volume up button until I hear a usb noise on my computer.
9008 mode is always there, it just doesn't always work.
leptdre said:
Hi guys,
I accidently bricked my LG G8 (Amazon Version) while trying to root it.
I have no download mode and no QDLoader mode. Is there a way to get the 9008 mode ?
Thanks
Click to expand...
Click to collapse
1. connect the phone to the computer using usb cable. then while holding power and vol-down press vol-up several times.
2. if you couldn't get into dload try first holding power + vol-down + vol-up for 30 seconds while the phone is connected to computer via usb cable.
3. it may not work either so you need to remove the back glass of the phone. then find two connectors on the board with the shape of a plus in a circle.
3-a. the connect the usb cable to phone but pull it out of the computer.
3-b. with a small wire try to connect the two connectors on the board together.
3-c. while the connectors are connected, put the usb cable back into the computer.
if the phone has no hw issue you will get into dload.
leptdre said:
Hi guys,
I accidently bricked my LG G8 (Amazon Version) while trying to root it.
I have no download mode and no QDLoader mode. Is there a way to get the 9008 mode ?
Thanks
Click to expand...
Click to collapse
After getting into EDL, follow this thread.
Alguien me puede ayudar tengo un lg g8 y no pasa de el modo edl no hace mas nada,nadamas puedo entrar en modo edl ?
Bonjour à tous, voici mon problème, j'ai un samsung galaxy a50 bloqué au démarrage, suite à une mauvaise manip avec twrp. Depuis je n'arrive pas à réinstaller le firmware, pourriez-vous m'aider ?
Translated by GT: Hello everyone, here is my problem, I have a samsung galaxy a50 stuck at startup, following a bad manipulation with twrp. Since I can not reinstall the firmware, could you help me?
Salut boot to bootloader et flash stock rom. La combinaison pour le démarrage dans le chargeur de démarrage est le volume + et - tout en connectant le port de charge au PC.
Translated by GT: Hi boot to bootloader and flash stock rom. The combination for booting into bootloader is volume + and - while connecting charging port to PC.
Victor_cris said:
Salut boot to bootloader et flash stock rom. La combinaison pour le démarrage dans le chargeur de démarrage est le volume + et - tout en connectant le port de charge au PC.
Click to expand...
Click to collapse
merci, mais l'oem est verrouillé et je ne peux pas le déverrouiller, le téléphone est en mode de récupération
Translated by GT: thanks, but the oem is locked and i can't unlock it, the phone is in recovery mode
Holy catfish! Friendly reminder about XDA Rule #4:
4. Use the English language.
We understand that with all the different nationalities, not everyone speaks English well, but please try. If you're really unable to post in English, use an online translator. You're free to include your original message in your own language, below the English translation. (This rule covers your posts, profile entries and signature). You could try :- https://translate.google.com/ or https://www.babelfish.com/ or use one of your choice.
Thank you!! Badger50 FSM
Phil58 said:
merci, mais l'oem est verrouillé et je ne peux pas le déverrouiller, le téléphone est en mode de récupération
Translated by GT: thanks, but the oem is locked and i can't unlock it, the phone is in recovery mode
Click to expand...
Click to collapse
Reboot to download mode and flash stock it can be flashed with OEM LOCK. (you can use this to get your rom https://samfirmtool.com/)
So, the firmware is installed, with odin, but now, the phone start all the time in recovery mode... I tried everything, wipe data/factory reset, wipe cache partition, nothing change... After reboot, I’ve this message: can’t load android system.... with 3 options, try again, facture data reset, and view recovery logs.... but nothing works....
Wipe factory reset bc the stock room that you download has data files corrupted Wipe data and wait.
Victor_cris said:
Wipe factory reset bc the stock room that you download has data files corrupted Wipe data and wait.
Click to expand...
Click to collapse
Ok, done... these are the screens after the Wipe data
On Odin options select nand erase flash stock again and make sure to flash all the files bc something is bad.
Also make sure you have flshed latest version of rom bc it shows older build code
Nope... doesn’t work... the problem is always the same...
I don’t know if it is the last firmware version, I took it with samfirm
did you changed a motherboard screen or battery ?
Victor_cris said:
did you changed a motherboard screen or battery ?
Click to expand...
Click to collapse
No....
Hi, I’ve flashed with an other stock, it start very well, but loop on the samsung logo....
And I can’t do anything
Hi, on which Samsung logo is the phone looping? "Samsung Galaxy A50, powered by Android" or "Samsung"
I had a similar problem with my phone rebooting to recovery mode, saying Can't load Android System after I restored it with Odin, but was able to fix it by just a factory reset.
My phone is Bulgarian (BGL) - You can try flashing my firmware for the Bulgarian variant of the A50 from SamMobile, also in Odin, select the following files -
BL - BL_XXXXXXXX
AP - AP_XXXXXXX
CP - CP_XXXXXXX
CSC - HOME_CSC_XXXXXXX
For Userdata, don't select anything
Here's a link to the Bulgarian firmware on SamMobile - https://www.sammobile.com/samsung/galaxy-a50/firmware/SM-A505FN/BGL/download/A505FNXXS9CVA3/1606986/ - It may take a while to download, because SamMobile limits the download speed to 300 KBps
Evgeni124 said:
Hi, on which Samsung logo is the phone looping? "Samsung Galaxy A50, powered by Android" or "Samsung"
I had a similar problem with my phone rebooting to recovery mode, saying Can't load Android System after I restored it with Odin, but was able to fix it by just a factory reset.
My phone is Bulgarian (BGL) - You can try flashing my firmware for the Bulgarian variant of the A50 from SamMobile, also in Odin, select the following files -
BL - BL_XXXXXXXX
AP - AP_XXXXXXX
CP - CP_XXXXXXX
CSC - HOME_CSC_XXXXXXX
For Userdata, don't select anything
Here's a link to the Bulgarian firmware on SamMobile - https://www.sammobile.com/samsung/galaxy-a50/firmware/SM-A505FN/BGL/download/A505FNXXS9CVA3/1606986/ - It may take a while to download, because SamMobile limits the download speed to 300 KBps
Click to expand...
Click to collapse
Hi, it’s a samsung a50 powered by android... but now, I can’t do anything, it doesn’t answer at any command
Oh, this is pretty bad, I though it was on the Samsung logo. Well in that case you can wait until the battery is fully drained, then try to boot into Download Mode by holding Vol- and Vol+ and plugging in the USB-C cable to the computer with Odin.
You can also try by holding Power + Vol-, while the charger is plugged in, then if the charging screen appears, remove the cable and try the above method to enter download mode. If the Samsung A50 Powered by Android logo appears, try again holding Power + Vol- and when the screen is black, quickly hold Vol- and Vol+ and plug-in the charger.
What did you do in TWRP, that caused this mess which even Odin has troubles fixing
Evgeni124 said:
Oh, this is pretty bad, I though it was on the Samsung logo. Well in that case you can wait until the battery is fully drained, then try to boot into Download Mode by holding Vol- and Vol+ and plugging in the USB-C cable to the computer with Odin.
You can also try by holding Power + Vol-, while the charger is plugged in, then if the charging screen appears, remove the cable and try the above method to enter download mode. If the Samsung A50 Powered by Android logo appears, try again holding Power + Vol- and when the screen is black, quickly hold Vol- and Vol+ and plug-in the charger.
What did you do in TWRP, that caused this mess which even Odin has troubles fixing
Click to expand...
Click to collapse
It start and switch on the samsung logo for 2 or 3 minutes, then stop and restart, switch on the samsung logo, etc....
Hmmm... So it's basically bootlooping, you can try the methods in my previous reply, if the second method doesn't work, you can just wait until the battery is drained and the phone shuts down, then hold Vol- and Vol+ and plug-in the USB-C cable. If the phone doesn't react to these methods, you can take it to a repair center, since most likely the motherboard or storage chip is broken or faulty.
Evgeni124 said:
Hmmm... So it's basically bootlooping, you can try the methods in my previous reply, if the second method doesn't work, you can just wait until the battery is drained and the phone shuts down, then hold Vol- and Vol+ and plug-in the USB-C cable. If the phone doesn't react to these methods, you can take it to a repair center, since most likely the motherboard or storage chip is broken or faulty.
Click to expand...
Click to collapse
Ok, now he is in the download mode.... What do I do now?
This thread is supposed to be a guide for anyone with a hard bricked XT2045-1 to be able to unbrick the device by forcing it into EDL mode to flash a new firmware. It is a work in progress and I will update it with the proper guide as soon as all steps are proven to work fine.
Long story short, I recently bought a XT2045-1 and it came with Android 11 installed. I wanted to install a custom ROM and noticed all SOFIAR ROMs require Android 10, so I tried to downgrade and got a bootloop, then used a blankflash to start fresh and the device did not boot to bootloader and simply it is not detected by the computer anymore (more info in this other thread).
Looking around, it seems that all G8 models are very similar, and I have found this video about unbricking a G8+ (XT2019) shorting two test points in the phone's board. I am not sure if it is the same person, but I am sure the procedure is related to this XDA thread with a picture from the service manual and a PDF guide for the same phone. So it seems that Vol_Up + Power does not work at all.
Continuing my research, I found this Reddit post that linked to the image below showing what seems to be the equivalent test points for the XT2045-1:
Screenshot
Captured with Lightshot
prnt.sc
The service manual can be found in the link below, and it seems that these are indeed the equivalent ones:
ESQUEMAS ELÉTRICOS - Motorola
nefybrasil.blogspot.com
I opened the phone and tried to short the two test points while connecting the USB cable, but still nothing was detected in the computer. I tried with both the flat cable from the screen connected or not, with the battery connected or not, no deal. When I plug the USB cable while the battery is not connected, I can see a white LED blink, nothing else. Before my phone bricked, I was able to boot into EDL mode only by booting the TWRP and then using adb reboot edl, so it does have an EDL mode.
Anyone tried to short the test points or starting the phone while pressing some buttons and it worked?
hello! Exactly the same thing happened to me, I did a downgrade and my phone died, now it has a black screen and I can't enter edl mode, did you find any solution?
I think I found the pins to enter EDL mode with the moto g8 power!
lfom said:
This thread is supposed to be a guide for anyone with a hard bricked XT2045-1 to be able to unbrick the device by forcing it into EDL mode to flash a new firmware. It is a work in progress and I will update it with the proper guide as soon as all steps are proven to work fine.
Long story short, I recently bought a XT2045-1 and it came with Android 11 installed. I wanted to install a custom ROM and noticed all SOFIAR ROMs require Android 10, so I tried to downgrade and got a bootloop, then used a blankflash to start fresh and the device did not boot to bootloader and simply it is not detected by the computer anymore (more info in this other thread).
Looking around, it seems that all G8 models are very similar, and I have found this video about unbricking a G8+ (XT2019) shorting two test points in the phone's board. I am not sure if it is the same person, but I am sure the procedure is related to this XDA thread with a picture from the service manual and a PDF guide for the same phone. So it seems that Vol_Up + Power does not work at all.
Continuing my research, I found this Reddit post that linked to the image below showing what seems to be the equivalent test points for the XT2045-1:
Screenshot
Captured with Lightshot
prnt.sc
The service manual can be found in the link below, and it seems that these are indeed the equivalent ones:
ESQUEMAS ELÉTRICOS - Motorola
nefybrasil.blogspot.com
I opened the phone and tried to short the two test points while connecting the USB cable, but still nothing was detected in the computer. I tried with both the flat cable from the screen connected or not, with the battery connected or not, no deal. When I plug the USB cable while the battery is not connected, I can see a white LED blink, nothing else. Before my phone bricked, I was able to boot into EDL mode only by booting the TWRP and then using adb reboot edl, so it does have an EDL mode.
Anyone tried to short the test points or starting the phone while pressing some buttons and it worked?
Click to expand...
Click to collapse
amigos yo hice todo el procedimiento que indicaron y mi pc detecta esto:
Luego realicé el proceso del archivo blankflash_sofiar_RPES31. Q4U-47-35-8 Pero el dispositivo nunca se reinicia en modo fastboot y solo se mantiene en negro y el led parpadea de vez en cuando ¿Ustedes encontraron alguna solución?
Loltimurightx said:
Luego realicé el proceso del archivo blankflash_sofiar_RPES31. Q4U-47-35-8 Pero el dispositivo nunca se reinicia en modo fastboot y solo se mantiene en negro y el led parpadea de vez en cuando ¿Ustedes encontraron alguna solución?
View attachment 5731697
Click to expand...
Click to collapse
Sorry for the late reply. Only recently I was able to unbrick my G8, it also had a hardware problem that made it impossible to enter EDL mode using the pads. Also it seems that newer firmwares have an anti-rollback feature, so you must use a blankflash file that is equal or newer than the firmware that was working when the phone bricked. More info here:
[Moto G8 XT2045-1] How to enter EDL when phone died?
Hello, there! I recently bought a XT2045-1 and wanted to install a custom ROM. Bellow are the results of the fastboot get_var all when the phone had it bootloader still locked: Searching XDA, I've found that all SOFIAR ROMs require that the...
forum.xda-developers.com
Long story short: yes, it is possible to enter EDL mode via hardware with the XT2045-1 phone. Using the service manual, it shows that FORCE_BOOT is linked to TP2312 and TP2313, so:
1. Make sure the phone is OFF, if you are not sure then carefully remove the battery, wait a few seconds and connect it again. You can keep the fingerprint sensor and display cables disconnected, the computer will show when the phone is connected. After you are sure the blankflash was successful and the phone can boot to fastboot, disconnect the battery and connect the display if you want.
2. Connect the two pads using something metallic (be careful to not damage the board) and only then connect the USB cable to the computer. If it worked, the computer will show a Qualcomm device. If you are on winblows you may need drivers, install Motorola RSA tools or similar if you see an unknown USB device.
3. For newer firmware versions, you cannot downgrade the bootloader, so you must use a version of singleimage.bin that has a bootloader that is equal or newer than the one the phone had when it was working fine. If you cannot find a correct version online, you can build one by yourself, see this thread on Reddit for more info.
I had to try to install a rom, because the screen turn black and no charge no sounds no ligths. What could i do with It?
Rtorlop said:
I had to try to install a rom, because the screen turn black and no charge no sounds no ligths. What could i do with It?
Click to expand...
Click to collapse
What rom did you try to install and what was the way you tried to install it? Does your pc still recognise the device when you plug it in? Fastboot or bootloader still availible?
Rtorlop said:
I had to try to install a rom, because the screen turn black and no charge no sounds no ligths. What could i do with It?
Click to expand...
Click to collapse
Try to enter to edl mode , push on the two volume buttons together and connect it to the PC , and look on the driver manager for 9008 driver
And use this guide
Mod edit: 4pda link removed since they are prohibited on XDA. Badger50 Senior Moderator
eliran0216 said:
Try to enter to edl mode , push on the two volume buttons together and connect it to the PC , and look on the driver manager for 9008 driver
And use this guide
Click to expand...
Click to collapse
La carga no funciona, no vibra, la pc no lo reconoce, el pulso vol- y pwr no hace nada. ya no tiene bateria
Mod translation: The charge does not work, it does not vibrate, the pc does not recognize it, the vol- and pwr pulse does nothing. it no longer has a battery
Robro86 said:
What rom did you try to install and what was the way you tried to install it? Does your pc still recognise the device when you plug it in? Fastboot or bootloader still availible?
Click to expand...
Click to collapse
global Rom without twrp, does not recognize pc, does not fastboot
Try to connect to the PC , and push on power + vol up for a minute
Or push power + volume down for a minute
And look if it help , if not help push on all the buttons for a minute
Thanks, i think this device is dead. Could i try edl cable?
Try another cable , maybe is not too good for bringing the device for life
eliran0216 said:
Try another cable , maybe is not too good for bringing the device for life
Click to expand...
Click to collapse
Not work
Did you try to push on power + two volume buttons for a minute (while the pone connected to the PC)?
Yes and do nothing
Try to hold all the buttons before you connected it to the PC and then connect it to the computer
No answer