Stack at Boot Logo - Huawei Ascend P6, Mate

Hi all and sory about my bad english,
I tryed to flash MIUI rom, and i made a few mistake and now i am stack at boot logo. But it working at bootloader mode. Can anyone help me how to install and run cwm recovery with fastboot commands.

bariskoca said:
Hi all and sory about my bad english,
I tryed to flash MIUI rom, and i made a few mistake and now i am stack at boot logo. But it working at bootloader mode. Can anyone help me how to install and run cwm recovery with fastboot commands.
Click to expand...
Click to collapse
Download the stock firmware and put dload folder in SD card. After that switch OFF the phone. Push at same time power and two volume buttons, phone will reboot in stock recovery and flash of stock ROM will start automatically.
After that you can try again to flash MIUI ROM.

alex.79 said:
Download the stock firmware and put dload folder in SD card. After that switch OFF the phone. Push at same time power and two volume buttons, phone will reboot in stock recovery and flash of stock ROM will start automatically.
After that you can try again to flash MIUI ROM.
Click to expand...
Click to collapse
Is it works even its stock recovery does not work. I mean, i am restarting phone by holding volume up and volume down buttons at the same time but Huawei original recovery mode not working. And would you please give me link of that stock rom.

bariskoca said:
Is it works even its stock recovery does not work. I mean, i am restarting phone by holding volume up and volume down buttons at the same time but Huawei original recovery mode not working. And would you please give me link of that stock rom.
Click to expand...
Click to collapse
I had the same problem after unsuccessfully installing MIUI. Huawei recovery didn't start, it just kept showing MIUI boot logo, and the updater launched but didn't do anything. I managed to get it working by formatting my SD and putting stock rom on it. Then the updater launched, recognised the update.app and the rest went smoothly.

Here you can download stock HUAWEI ROM: http://www.huaweiblog.de/downloads/ascend-p6-downloads/
Recovery which you use to flash MIUI is a temporally. It not affect your stock recovery. On my phone this method work perfect. Push all buttons in same time until stock recovery it start.

kaspars_l said:
I had the same problem after unsuccessfully installing MIUI. Huawei recovery didn't start, it just kept showing MIUI boot logo, and the updater launched but didn't do anything. I managed to get it working by formatting my SD and putting stock rom on it. Then the updater launched, recognised the update.app and the rest went smoothly.
Click to expand...
Click to collapse
Would you please give me link of that update.app file?

alex.79 said:
Here you can download stock HUAWEI ROM: http://www.huaweiblog.de/downloads/ascend-p6-downloads/
Recovery which you use to flash MIUI is a temporally. It not affect your stock recovery. On my phone this method work perfect. Push all buttons in same time until stock recovery it start.
Click to expand...
Click to collapse
Doesnt start huawei recovery. There is only boot logo "HUAWEI Ascend"

bariskoca said:
Would you please give me link of that update.app file?
Click to expand...
Click to collapse
Unzip this and put the dload folder on your SD
http://dl.huaweinews.com/Roms/Ascend-P6/B118.zip

kaspars_l said:
Unzip this and put the dload folder on your SD
http://dl.huaweinews.com/Roms/Ascend-P6/B118.zip
Click to expand...
Click to collapse
I will try it. Thak you very much all.

bariskoca said:
Doesnt start huawei recovery. There is only boot logo "HUAWEI Ascend"
Click to expand...
Click to collapse
Recovery will start a few seconds after HUAWEI logo. But first turn off the phone and after that push and hold all button while recovery start.

kaspars_l said:
Unzip this and put the dload folder on your SD
http://dl.huaweinews.com/Roms/Ascend-P6/B118.zip
Click to expand...
Click to collapse
Unzipped files to sdcard. Restarted phone by holding power button and volume up + volume down buttons. Nothing happend. Still stacked at Boot Logo. Even i cant switch off phone. when i hold power button its only restarting.

Damn, then I have no idea what to do. Lets hope you haven't bricked it and someone can come up with a solution.

kaspars_l said:
Damn, then I have no idea what to do. Lets hope you haven't bricked it and someone can come up with a solution.
Click to expand...
Click to collapse
Oh now something happend. I connected the phone to charge. Then i tryed to recover. First time came up lines from up to down. Tryed again. Now writing on screen but doing nothing;
USB Update Enter...
HUAWEI SDCARD&USB UPDATE AGENT VERSION 2.0
This phone is secureboot phone.
This phone is LOCK state.
Then restarted phone by holding power button. HUAWEI recovery worked. But it didnt update phone. I choosed apply update from extenal storage, entered dload directory. But i couldnt see update.app file. Returned back entered again to update from external storage even didnt show dload directory. What should i do now.

Download ROM, unzip and you see dload folder with UPDATE.APP inside. Put dload folder in main directory on SD card via PC. Put the card on the phone. Push all buttons (power, volume up, volume down) at same time while phone is reboot on stock recovery. After that HUAWEI SDCARD&USB UPDATE AGENT VERSION 2.0 will find UPDATE.APP in dload folder automatically and flash process will start.

bariskoca said:
Oh now something happend. I connected the phone to charge. Then i tryed to recover. First time came up lines from up to down. Tryed again. Now writing on screen but doing nothing;
USB Update Enter...
HUAWEI SDCARD&USB UPDATE AGENT VERSION 2.0
This phone is secureboot phone.
This phone is LOCK state.
Then restarted phone by holding power button. HUAWEI recovery worked. But it didnt update phone. I choosed apply update from extenal storage, entered dload directory. But i couldnt see update.app file. Returned back entered again to update from external storage even didnt show dload directory. What should i do now.
Click to expand...
Click to collapse
Oh, this is where I was stuck for a while. This is where I formatted my SD and copy the dload folder to SD. Then the update happened.

Yes now it worked thanks all of you and xda.
Sent from my HUAWEI P6-U06 using xda app-developers app

Related

[Q] Please Help :(

Hi!
So there is my problem:
I upgraded to KitKat and tryed to install gapps but then everything f* up. So with TWRP I tried to install B125 but it didn't work so I put this B111 on my phone than I tried to install it but it failed and TWRP says that there isn't OS on my phone
Also I don't have any sd card..
What can i do?
maticex said:
Hi!
So there is my problem:
I upgraded to KitKat and tryed to install gapps but then everything f* up. So with TWRP I tried to install B125 but it didn't work so I put this B111 on my phone than I tried to install it but it failed and TWRP says that there isn't OS on my phone
Also I don't have any sd card..
What can i do?
Click to expand...
Click to collapse
Go get an SD CARD from someone and put on it B125 International Version or any other ROM for that matter, and do it fast until your phone runs out of battery. Put update.app in dload folder. You can do it through adb and fastboot, but the safest way is the way that I have just told you. And after that press the Power button and volume up/down at once, all of them until stock recovery starts updating/upgrading... well installing the new ROM, I hope you still have stock recovery.
So when I put it in dload and put it in phone what next?
maticex said:
So when I put it in dload and put it in phone what next?
Click to expand...
Click to collapse
Press the Power button and volume up/down at once, all of them until stock recovery starts. If you only have TWRP find a flashable ROM that is a ZIP, and flash it through TWRP.
ZuperStyler said:
Press the Power button and volume up/down at once, all of them until stock recovery starts. If you only have TWRP find a flashable ROM that is a ZIP, and flash it through TWRP.
Click to expand...
Click to collapse
I have b111.zip in my internal storage if it helps?
maticex said:
I have b111.zip in my internal storage if it helps?
Click to expand...
Click to collapse
You must move it to an SD CARD, get one from someone just to restore your phone.
ZuperStyler said:
You must move it to an SD CARD, get one from someone just to restore your phone.
Click to expand...
Click to collapse
Do you know any B125 firmware which is in zip? not APP. file
maticex said:
Do you know any B125 firmware which is in zip? not APP. file
Click to expand...
Click to collapse
i advise you to flash this ROM, try it. http://forum.xda-developers.com/showthread.php?t=2585783 Must work since you had KitKat, your bootloader must be unlocked. Try CyanogenMod 10.1 following the instructions. But again, use an SD CARD.
ZuperStyler said:
i advise you to flash this ROM, try it. http://forum.xda-developers.com/showthread.php?t=2585783 Must work since you had KitKat, your bootloader must be unlocked. Try CyanogenMod 10.1 following the instructions. But again, use an SD CARD.
Click to expand...
Click to collapse
I'll try probably
maticex said:
I'll try probably
Click to expand...
Click to collapse
Try ? LOL Any ROM is good to put your phone into a workable state. After that, install whatever ROM you like.
I understood that this ROM can be instaled only via CN 118?
maticex said:
I understood that this ROM can be instaled only via CN 118?
Click to expand...
Click to collapse
I had B125 International Locked and then I flashed KitKat, and after that CyanogenMod 10.1 and worked. Now, fell free to try what you want, but if you want to be safe install stock recovery if you don't have it anymore and upgrade from dload folder B125. All the info you want you can find on XDA. Just search what you need.
ZuperStyler said:
I had B125 International Locked and then I flashed KitKat, and after that CyanogenMod 10.1 and worked. Now, fell free to try what you want, but if you want to be safe install stock recovery if you don't have it anymore and upgrade from dload folder B125. All the info you want you can find on XDA. Just search what you need.
Click to expand...
Click to collapse
Do you maybe have original stock recovery file and do I just flash it with TWRP?
maticex said:
Do you maybe have original stock recovery file and do I just flash it with TWRP?
Click to expand...
Click to collapse
But you don't have an OS.
Put your device in fastboot mode ( > adb reboot bootloader )
Extract recovery.img from archive
fastboot flash recovery recovery.img ;
fastboot reboot ;
Tell me what stock recovery do you want.
Place the ZIP with the recovery let's say on Local Disk ( C: ) Create a folder and name it fastboot. Put the recovery ZIP in that folder. After that connect your phone to the PC, now press shift and right click on your mouse or on your laptop and press Open Command Window here. There you write adb bootloader and press enter.
fastboot flash recovery recovery.img ;
fastboot reboot ;
defo just get like a 4gb sd card.
Thank you for all I'm on cm now, but I don't like that I can't take photos with it Can I get camera working?
How can I install normal huawei software now?
Revert to stock recovery first.
How can I do this, I don't find threads with how can i do this?
Can I get Camera working there it says that it is working but on my phone gallery chrashes when I open camera app
Use Camera360, works perfectly.
maticex said:
Hi!
So there is my problem:
I upgraded to KitKat and tryed to install gapps but then everything f* up. So with TWRP I tried to install B125 but it didn't work so I put this B111 on my phone than I tried to install it but it failed and TWRP says that there isn't OS on my phone
Also I don't have any sd card..
What can i do?
Click to expand...
Click to collapse
i done someting similar after trying to put b125 back to phone.. well he was stuck at start with huawei logo..anyway i don`t put on my sd card any zip.. i put on main sdcard the folder "dload" and inside that folder was update.app." file
soo... {my phone was freezeing with huawei logo not opening up anymore so i put that folder on sdcard useing diferent phone then i connect phone to usb and hold power putton this way that logo with huaway disear and phone restarted.in that moment i take off finger from power button .and then holding the volume plus minus and again power button . anyway not sure if was needed to conect phone at usb to restart it but for me works }
i done nothing more.. nothing on computer.. the instalation of b125 works normaly directly from that recovery menu

Bricked ascend p6

So this morning I wanned to update my Jelly Bean to kitkat . I have my ascend p6 only 2months , earlyier i had galaxy young ,and i installed many roms on him, so i wanned to instal kitkat on this phone, so i installed cwm and started in recovery mode, after that i tried to instal, Look for the attachment
when i tried to chose zip from sd card nothing showed up it just like crashed or smth , after that i tried to restart and start again in recovery , in this time i chose zip from/storage/sd card , in this time it showed up and i tried to instal rom, after that i tried to instal gaps and superuser, both of them failed, then i restarted my phone and it stuck on Huawei ascend logo, its has been for some hours im trying to fix this, i've looked all over internet, i tried to take out sd card and put B125.zip file and instal it, i read it on net that it can help, after that i putted back my sd card in phone and after that i tried to go into recovery mode , put the phone doesnt reads the SD CARD !!!!!!!!!!!!!!!!! help please !!!!
Extract the zip, put the update.app in the dload folder on the SD card, then force update with volume up, volume down and power button. Hold those until it starts updating. Always do a bit of research before just flashing!!
Sent from my P6-U06 using Tapatalk
Don't forget to flash a stock recovery from fastboot mode first.
uhm please tell me the instructions , i don't understand all of what ur saying
lootjelo said:
Extract the zip, put the update.app in the dload folder on the SD card, then force update with volume up, volume down and power button. Hold those until it starts updating. Always do a bit of research before just flashing!!
Sent from my P6-U06 using Tapatalk
Click to expand...
Click to collapse
Hey buddy, i tried it , but when the update start , it looks like this:
USB UPDATE ENTER...
HUAWEI SDCARD&USB UPDATE AGENT VERSION 2.0
this phone is secureboot phone.
this phone is LOCK state. .............. And after that nothing it just like freezes, even that loading tab is frozen, idk i need to wait or i need to do something else?
GrizzLV said:
Hey buddy, i tried it , but when the update start , it looks like this:
USB UPDATE ENTER...
HUAWEI SDCARD&USB UPDATE AGENT VERSION 2.0
this phone is secureboot phone.
this phone is LOCK state. .............. And after that nothing it just like freezes, even that loading tab is frozen, idk i need to wait or i need to do something else?
Click to expand...
Click to collapse
So it dosnt find your sdcard/ or update file.. It needs to be in FAT32, NTFS dosnt work..
And remember make dload folder where to add update.app file

Stuck in boot, Will pay whoever solves the issue and provides me a step by step fix

Hello,
I'm looking for help as I have exhausted all of my search on google and xda developers and the answer doesn't seem to be there. I'm afraid I might be unable to get out of this one.
I have a huawei ascend P6-U06 I bought it and it came with the international firmware, I had rooted it and flashed miui v5 into my phone, everything was fine but one thing, I was unable to use themer, so about 3 days ago I finally decided to flash omni rom.
I downloaded omni rom and installed CWM recovery and once into the system I selected the zip from my sd card and flashed it, only to find that the phone would not go pass the first screen (stuck in boot and could not be shutdown or anything)
Since I did not do a TWRP recovery (and I don't know how, I'm just a beginner) I was unable to do anything other than the "3 button method" so I looked and found that I could put the UPDATE.APP file on the dload folder and it should work, so I tried it and the UPDATE.APP firmware version is the B125, all good I think this was the Chinese version but it had English and other languages as well, but Chinese seemed to be the main one.
Anyways I had the phone back and it did an update, after the update everything was working fine, I deleted the dload file from the sd card, also I saw that the "system" or the phone itself created a dload file on the internal storage but then once I had themer on the phone I saw myself that I hated the emotion ui and in the first place that was the reason I had put miui into my phone, I still wanted to try omni rom and persistently I tried a second time.
Now this time since I already new that I could just do the dload thingy I thought (what could happen) so I tried again with CWM to flash the omni rom (the latest version) but it gave me an error saying something like the installation was aborted or something like that.
So I went back to having the phone stuck in boot, I put the B125 UPDATE.APP and created a dload folder on the sd card, but when doing the "3 button method" the system gave me an error, I tried downloading the B122 and the B132 and also the B510 but although I have put the UPDATE.APP on the dload folder it just doesn't do it's magic like it previously did.
Now I don't really have money to buy another phone, if I did I would just buy another one (I like the p7) but I don't so I need to fix this issue otherwise I don't have a phone.
The error I get first it gives me some sort of error which disappears once the Android system recovery menu comes up. then the only thing I'm able to see says:
Checking Module MD5RSA.. OK
Checking Module CRC.... OK
Checking Module CURVER.... OK
Checking Module VERLIST....
Huawei SD card update fail.....
cust copying files...
copy cust files successed!
===================
FAIL
===================
Please help me, I'd appreciate if you can do your best explaining as I'm dumb in this matter, (just a beginner as said before) Also I'm attaching a picture of the error message being received when entering the system recovery through the "3 button method"
And as I said on the tittle, I will pay whoever helps me to solve this issue, I need a step by step (with a good explanation if possible) on how to fix it, I will pay $60 via paypal to the person that provides me with the solution.
Thanks for all of your time, I DO appreciate your help and if you have any questions please just ask! I really need to fix this!
Ok, first of all, your picture shows that you already have the KitKat recovery.
Which version of B510 have you downloaded? Is it the update.zip? I'm assuming it is...
Please download the complete update package from here: http://www.huaweidevice.ro/user/con...001C00B510_Firmware_Android 4-4_EMUI--2-3.zip
That is the official, and full firmware update from Huawei Romania.
Once your download has completed, unzip the zip file, and copy the dload folder onto your sd card.
BEFORE placing your sd card back in your phone, try the 3 button method again. You should get into recovery mode, then do a data/factory reset, and clear cache.
Once that is done, put your sd card back in your phone, reboot your device, and reboot using the 3 button method.
Hopefully this will work.
If it fails again, you need to try formatting your sd card, and do the steps above again, without doing a factory reset.
Dear op.... Did you solve your problem? How?
miz_pimp said:
Ok, first of all, your picture shows that you already have the KitKat recovery.
Which version of B510 have you downloaded? Is it the update.zip? I'm assuming it is...
Please download the complete update package from here: http://www.huaweidevice.ro/user/con...001C00B510_Firmware_Android 4-4_EMUI--2-3.zip
That is the official, and full firmware update from Huawei Romania.
Once your download has completed, unzip the zip file, and copy the dload folder onto your sd card.
BEFORE placing your sd card back in your phone, try the 3 button method again. You should get into recovery mode, then do a data/factory reset, and clear cache.
Once that is done, put your sd card back in your phone, reboot your device, and reboot using the 3 button method.
Hopefully this will work.
If it fails again, you need to try formatting your sd card, and do the steps above again, without doing a factory reset.
Click to expand...
Click to collapse
I tried it but it's still not working. :/
blackrose1 said:
Dear op.... Did you solve your problem? How?
Click to expand...
Click to collapse
I"m still looking for a solution, actually it's been so long that I'm offering to pay whoever provides me with the solution
Try what I did here to solve a similar problem that I had: http://forum.xda-developers.com/showpost.php?p=54124890&postcount=18
sko4a said:
Try what I did here to solve a similar problem that I had: http://forum.xda-developers.com/showpost.php?p=54124890&postcount=18
Click to expand...
Click to collapse
I have a question, how can I install TWRP if the adb fastboot is not recognizing my phone? I think it's because I'm missing the drivers but I haven't been able to find them.
DanRioja said:
I have a question, how can I install TWRP if the adb fastboot is not recognizing my phone? I think it's because I'm missing the drivers but I haven't been able to find them.
Click to expand...
Click to collapse
Don't you just need Hisuite, the driver who comes with the phone when you plug in your USB cable? That made asb fastboot to recognize my phone at least.
You don't need ADB, only fastboot. Shut down the phone. Then hold the Vol- button and plug in the usb cable. Release the button after the you see the AscendP6 logo - now you are in fastboot and can flash TWRP. Windows Update should install the drivers (I've never installed HiSuite), just let it search online.
First delete your sd card to FAT32 not NTFS and put update.app to dload folder. then dowbload: http://forum.xda-developers.com/showthread.php?t=2765202
Power up your phone with volume down. and use Huawei tool kit from that link. select KitKat , unlock bootleder first from dropdown menu, then install stock recovery.
And try to update from stock recovery "3 buttons method"
ADHDDHDA said:
First delete your sd card to FAT32 not NTFS and put update.app to dload folder. then dowbload: http://forum.xda-developers.com/showthread.php?t=2765202
Power up your phone with volume down. and use Huawei tool kit from that link. select KitKat , unlock bootleder first from dropdown menu, then install stock recovery.
And try to update from stock recovery "3 buttons method"
Click to expand...
Click to collapse
Hey so far this is the most promising option I've gotten, the only problem is when I go to unlock bootloader it's giving me an error that says "error phone not connected" I've tried getting the drivers from many different ways, one from the hi suite, another letting windows look for it, the other one was I downloaded a .exe named "driver tools" but it doesn't work either, when I connect the phone it does make the sound just as when you connect any device on USB but other than that it doesn't recognizes it on the huawei toolkit. Any ideas?
sko4a said:
You don't need ADB, only fastboot. Shut down the phone. Then hold the Vol- button and plug in the usb cable. Release the button after the you see the AscendP6 logo - now you are in fastboot and can flash TWRP. Windows Update should install the drivers (I've never installed HiSuite), just let it search online.
Click to expand...
Click to collapse
I only get to see this screen: http://s3.amazonaws.com/f01.justanswer.com/JACUSTOMERd2wl5hbc/2013-01-26_122110_huawei.jpg
Tungieee said:
Don't you just need Hisuite, the driver who comes with the phone when you plug in your USB cable? That made asb fastboot to recognize my phone at least.
Click to expand...
Click to collapse
I've tried with the hi suite, downloading a .exe driver named "driver tools" and having windows look for the driver, but it doesn't recognizes it, I mean when I connect the phone it does make the sound when you're connecting something but other than that the adb is not recognizing the phone.
I had a similar problem but for me it would say verlist fail. However you should try this anyway if you haven't already: http://forum.xda-developers.com/showpost.php?p=52744051&postcount=23
What is important is that you use the recovery in that specific post. That's what fixed it for me.
blacklord9 said:
I had a similar problem but for me it would say verlist fail. However you should try this anyway if you haven't already: http://forum.xda-developers.com/showpost.php?p=52744051&postcount=23
What is important is that you use the recovery in that specific post. That's what fixed it for me.
Click to expand...
Click to collapse
I have a question, how can I flash the stock recovery? I mean I have tried with the adb fastboot but it doesn't recognizes the phone :/
Try this methode, it defently works!!! I had EXACT the same problem! P.s. You dont need to flash a other recovery!!!!!!!!!!
http://forum.xda-developers.com/showthread.php?t=2781977

[Q] Ascend P6 Bootloop

Hello all.
I know this has been asked a gazillion of times, but the solutions I can find, are not working for me.
I rooted my phones yesterday, for the first time and all went great. I got reverse tether to work etc etc.
I installed a few apps, and they all worked.
Then i installed Xposed framework, and it got me into a bootloop.
I tried flashing the recovery_original_flashable.img from another thread and this went perfect, but it still is in the bootloop. I can get into recovery, but it does nothing. It just lets me wipe cache and or do a factory reset and those both have no effect whatsoever.
I know I might be doing something wrong, can anyone help me?
And sorry if I am just forgetting one step in all of this.
Thanks in advance
pmbMixx
EDIT:
I got the stock rom ready, yet, I cannot exit my SD card to copy the update.app file. This is due to a drop a year back, it is bend at the sd card slot and when I use a little needle to make it come up it tries to push the whole sidepanel off, I tried connecting to fastboot and using ADB push command to drop the file there, but it does not see my device.
How to move on?
pmbMixx said:
Hello all.
I know this has been asked a gazillion of times, but the solutions I can find, are not working for me.
I rooted my phones yesterday, for the first time and all went great. I got reverse tether to work etc etc.
I installed a few apps, and they all worked.
Then i installed Xposed framework, and it got me into a bootloop.
I tried flashing the recovery_original_flashable.img from another thread and this went perfect, but it still is in the bootloop. I can get into recovery, but it does nothing. It just lets me wipe cache and or do a factory reset and those both have no effect whatsoever.
I know I might be doing something wrong, can anyone help me?
And sorry if I am just forgetting one step in all of this.
Thanks in advance
pmbMixx
EDIT:
I got the stock rom ready, yet, I cannot exit my SD card to copy the update.app file. This is due to a drop a year back, it is bend at the sd card slot and when I use a little needle to make it come up it tries to push the whole sidepanel off, I tried connecting to fastboot and using ADB push command to drop the file there, but it does not see my device.
How to move on?
Click to expand...
Click to collapse
Since you cant remove the sdcard and you are on stock recovery i would first suggest that you flash twrp recovery in order to get to the sdcard. Once you can boot to twrp you can mount the storage on your computer and from there copy the update.app file you need to install a fresh copy of the system. When thats done you can flash back the stock recovery and update normaly.
tileeq said:
Since you cant remove the sdcard and you are on stock recovery i would first suggest that you flash twrp recovery in order to get to the sdcard. Once you can boot to twrp you can mount the storage on your computer and from there copy the update.app file you need to install a fresh copy of the system. When thats done you can flash back the stock recovery and update normaly.
Click to expand...
Click to collapse
Thank you, I will try this and let you know how it worked out!
pmbMixx said:
Thank you, I will try this and let you know how it worked out!
Click to expand...
Click to collapse
Got it on there now,
Flashed the stock recovery back
Reboot into recovery->Error -> E:failed to mount.
What now? Thanks for the help in advance!
Edit:
Ok, I have gotten it to mount at least one time, but it will not run the UPDATE.APP, not with booting with VOL - and + pressed, not with VOL+ pressed nor with VOL - pressed.
I can enter the SD card, but after going in into the folders and going back it disconnects the SD card and it is failed to mount again.
pmbMixx said:
Got it on there now,
Flashed the stock recovery back
Reboot into recovery->Error -> E:failed to mount.
What now? Thanks for the help in advance!
Edit:
Ok, I have gotten it to mount at least one time, but it will not run the UPDATE.APP, not with booting with VOL - and + pressed, not with VOL+ pressed nor with VOL - pressed.
I can enter the SD card, but after going in into the folders and going back it disconnects the SD card and it is failed to mount again.
Click to expand...
Click to collapse
So you are on the stock recovery with the update.app file place in a dload folder in your sdcard and it cant start the update process?
tileeq said:
So you are on the stock recovery with the update.app file place in a dload folder in your sdcard and it cant start the update process?
Click to expand...
Click to collapse
Correct.
I went on trying some things, and it would not update back to the stock rom. I tried flashing TWDR (right?) and that worked, and after that I tried flasing the Cyanogen mod rom, and its working again. Although I must say, its buggy as frack.
for example: Camera wont show, it opens app but then keeps showing homescreen with a gray overlay, and when pressing the power button, it wont ever show me a menu to restart or shutdown etc.
Anyone using a rom on the P6 that does not have this problem?
Summary: I can flash custom roms, I cant flash stock roms for some reason...

Help installing any rom, sudden soft brick

Hi, yesterday my phone ran out of battery and when i charged it only appear the Ascend logo and then got stuck on the android screen, been trying to install any rom but it doesnt recognize any in the dload folder, also when i perform a factory data after the message formatting/cache it says "reset ad remain times error! anyone nows what does it mean, thanks.
vampvr said:
Hi, yesterday my phone ran out of battery and when i charged it only appear the Ascend logo and then got stuck on the android screen, been trying to install any rom but it doesnt recognize any in the dload folder, also when i perform a factory data after the message formatting/cache it says "reset ad remain times error! anyone nows what does it mean, thanks.
Click to expand...
Click to collapse
What is your recovery ? If you have TWRP plug your phone to usb them connect your phone has a fisical storage to computer.
Search "dload" folder and replace it with another d.load file.
Restart the phone to TWRP and the dload maybe start work again I think, try it
If not
You need to use adb fastboot to install "TWRP recovery", then restart in adb mode to recovery.
Hope it help.
AngelOfBlood said:
What is your recovery ? If you have TWRP plug your phone to usb them connect your phone has a fisical storage to computer.
Search "dload" folder and replace it with another d.load file.
Restart the phone to TWRP and the dload maybe start work again I think, try it
If not
You need to use adb fastboot to install "TWRP recovery", then restart in adb mode to recovery.
Hope it help.
Click to expand...
Click to collapse
i have stock recovery, it had the b707 rom, the adb wont recognize my phone
vampvr said:
i have stock recovery, it had the b707 rom, the adb wont recognize my phone
Click to expand...
Click to collapse
Can you enter fstboot mode and connect it with the pc while in fb mode? When its powered off, press power button and hold volume down button. If it works ok it should be stuck on huawei ascend logo, that means that you are in fastboot mode. If you can do it them you can try to wipe all and reinstall recovery and boot files from the update then try to flash a system.
Sent from my SM-G850F
tileeq said:
Can you enter fstboot mode and connect it with the pc while in fb mode? When its powered off, press power button and hold volume down button. If it works ok it should be stuck on huawei ascend logo, that means that you are in fastboot mode. If you can do it them you can try to wipe all and reinstall recovery and boot files from the update then try to flash a system.
Sent from my SM-G850F
Click to expand...
Click to collapse
yes i can enter fastboot mode, it got stuck on huawei logo, do you know where i can find a tutorial to wipe all and reinstall recovery with boot files, i had a saved tutorial but i lost it
vampvr said:
yes i can enter fastboot mode, it got stuck on huawei logo, do you know where i can find a tutorial to wipe all and reinstall recovery with boot files, i had a saved tutorial but i lost it
Click to expand...
Click to collapse
Just search for fastboot commands and get the files ready before any wiping.
Sent from my SM-G850F
ok now i got the boot img loaded, do i need to upload the os with the .img or only the update.app?
vampvr said:
ok now i got the boot img loaded, do i need to upload the os with the .img or only the update.app?
Click to expand...
Click to collapse
If you flashed boot and recovery now try to install update.app.
Sent from my SM-G850F
tileeq said:
If you flashed boot and recovery now try to install update.app.
Sent from my SM-G850F
Click to expand...
Click to collapse
i tried to install update.app but nothing happens, i put a zip folder with the update.app and the boot.img but it appears on the screen e:signature verification failed, im going to try doing it again with the b116sp1
vampvr said:
i tried to install update.app but nothing happens, i put a zip folder with the update.app and the boot.img but it appears on the screen e:signature verification failed, im going to try doing it again with the b116sp1
Click to expand...
Click to collapse
The update.app file should be placed in a folder named dload on the root of the sd card.
Sent from my SM-G850F
---------- Post added at 19:10 ---------- Previous post was at 19:09 ----------
And btw you should have flashed boot.img together with recovery.
Sent from my SM-G850F
still cant put any rom, all i get is e:signature verification failed, i put all the folders on the root of the sd card and im trying with 2 sd cards, im goint to take it to huawei next monday
tileeq said:
The update.app file should be placed in a folder named dload on the root of the sd card.
Sent from my SM-G850F
---------- Post added at 19:10 ---------- Previous post was at 19:09 ----------
And btw you should have flashed boot.img together with recovery.
Sent from my SM-G850F
Click to expand...
Click to collapse
i flashed boot.img with recovery but still cant install any rom, im still getting the message e:signature verficiation failes
vampvr said:
Hi, yesterday my phone ran out of battery and when i charged it only appear the Ascend logo and then got stuck on the android screen, been trying to install any rom but it doesnt recognize any in the dload folder, also when i perform a factory data after the message formatting/cache it says "reset ad remain times error! anyone nows what does it mean, thanks.
Click to expand...
Click to collapse
Did you try to flash again b707? Idk any more solution except if you try repacking update.app with Huawei update extractor and flashing img by img... it's worth to try
Sent from my HUAWEI P6-U06 using XDA mobile app
AdnanCG said:
Did you try to flash again b707? Idk any more solution except if you try repacking update.app with Huawei update extractor and flashing img by img... it's worth to try
Sent from my HUAWEI P6-U06 using XDA mobile app
Click to expand...
Click to collapse
i cant find the b707, its no longer available at the huawei page
vampvr said:
i cant find the b707, its no longer available at the huawei page
Click to expand...
Click to collapse
It is still available here: http://emui.huawei.com/cn/plugin.php?id=hwdownload&mod=detail&mid=42
miz_pimp said:
It is still available here: http://emui.huawei.com/cn/plugin.php?id=hwdownload&mod=detail&mid=42
Click to expand...
Click to collapse
thanks im dowonloading now, hope this works
i downloaded the b707 rom but i put the dload folder and when i try to update it it only appears ../ could it be that the motherboard is dead?
vampvr said:
i downloaded the b707 rom but i put the dload folder and when i try to update it it only appears ../ could it be that the motherboard is dead?
Click to expand...
Click to collapse
finally i take my phone to service and they gave me a new one, they told me that maybe the rom b707 that i installed fried the main board
vampvr said:
finally i take my phone to service and they gave me a new one, they told me that maybe the rom b707 that i installed fried the main board
Click to expand...
Click to collapse
I'm glad you got a replacement!

Categories

Resources