Hi, has anybody there tried replacing flex cable by himself?
http://www.youtube.com/watch?v=-3n5ZfkqhzE
In this guide pause on 5:41, guide creator stops dissasembling at this point. Is it possible to change flex cable without service? If yes, please say how.
I did... just replaced my broken flex cable yesterday
Here is the link for the pics
http://www.kaskus.co.id/showpost.php?p=713664484&postcount=1804
Translation:
Title: Hurrah.. My Xperia Play is healthy again
This evening my order of flex cable (2 pcs) has just arrived, going to continue repairing my PLAY which is still on ICU..
Swear god, took me at least 3 hours learning n try carefully by myself how to take out the flex cable n put it back properly from PLAY
Pic 1: spoiler for at last success take the flex cable out
pic note: Left one is the broken flex cable (see the black carbon's gone -- i think that's the problem causing the screen turn to white).. Right one is the new flex cable (the black carbon's still fresh and full)
Pic 2: spoiler for new flex cable been put properly
Pic 3: spoiler for broken n new ones
pic note: Left one is the broken flex cable, right one is the new one, i keep it as stock for future use b'coz am almost 100% sure the flex cable will break again 1 - 2 years coming
Pic 4: spoiler for PLAY already healthy
P.S Got no cam here, so can't record the process how to replace it.. I just watch n practice carefully from these two videos guide how to take off part by part although not completely (because the flex cable part was not included in the videos)
http://www.youtube.com/watch?v=-3n5ZfkqhzE
http://www.youtube.com/watch?v=vRjC19j2m48
Tried google whole day before, to find any information or guide how to replace the flex cable, but couldn't find it... At last have to try it myself for hours n succeed
Sorry to be bumping an old thread, but in my experience I already had 3 broken slider flexes, all of which had the same problem: the black carbon material wearing off. It that's what's causing our slider problems, wouldn't it be better if we put a very thin adhesive tape (tge transparent one) around the carbon part to keep it from wearing off before installing? I'm no hardware expert but I am pretty experienced in replacing broken parts.
I would suggest to use the black insulating adhesive tape, it's the best way to not have electrical problems and it's thin enough.
^ you mean the 3M- or Crocodile branded black electrical tape? That's thick IMO and leaves a sticky residue on itself while sliding off which may be of more harm than good.
Some how (isn't that what they all say) got water in my GNex USB Port which caused the port to fry once charger was plugged in. Phone still fully functions as normal, just can't charge it. After pricing out a few options, I've decided to replace the part myself. Should everything go well, this should save me at least $35.
Just wondering if anyone else here as had to do this, would love to hear how it went for you. I'm currently waiting for the part to be shipped to me.
There's been quite a few people (not me so far) who've had to change their usb ports because they failed (stopped charging). There's several threads on how to do it, I've not bookmarked them but search would probably turn them up.
Should be pretty simple if the charging port is on a daughterboard and not on the main PCB. It's pretty easy to remove the lcd/digitizer + mainboard from the housing, and if it's just a daughterboard you should be able to disconnect the old part from the connector and attach the new one.
Thanks for the replies! ifixit.com actually has a detailed step by step, just wanted to see if anyone here ran into any issues while doing it or not.
Careful with the buttons
Gforce083 said:
Thanks for the replies! ifixit.com actually has a detailed step by step, just wanted to see if anyone here ran into any issues while doing it or not.
Click to expand...
Click to collapse
Its fairly easy to replace the USB board if done with care and proper tools. A word of advice, when you remove the back cover ( the step after removing screws) pay attention to not drop the rubber buttons..... they are hard to find once they hit the floor . Anything than that, just do it with love and you will do fine
Success! Time to put the Aria back in the closet!
I take that back, the microphone (which is part of the usb port board) on the new board does not work. Attempted to make a phone call and they could not hear me. Used a voice recording app and got nothing. Looks like I'll be getting another replacement.
I've got to hand it to Wholesale Gadget Parts, Inc out of Oklahoma. That's saying a lot coming from a Texan, we usually aren't too fond of Oklahoma. As stated the other day, the replacement board I got had a faulty microphone. Called WGP, no questions asked shipped me a new one and got it within 48 hours. My GNex is now back to fully functioning order!
Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
http://www.witrigs.com/media/catalo...a71cb48e3d52cb890e76f9e6353/1/0/109063-01.jpg
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
bookfast said:
Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
http://www.witrigs.com/media/catalo...a71cb48e3d52cb890e76f9e6353/1/0/109063-01.jpg
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
Click to expand...
Click to collapse
Hey there. Interesting to know that you replaced it all your self . Did you put everything back perfectly ? I mean the display being aligned properly to the body, the speaker grills being flushed with the body; ? Weird to ask, but did you damage anything while doing it all yourself ? Like the screen scratches, or something else ? Sorry, for asking these... Thanks in advance :good:
Tej XFire said:
Hey there. Interesting to know that you replaced it all your self . Did you put everything back perfectly ? I mean the display being aligned properly to the body, the speaker grills being flushed with the body; ? Weird to ask, but did you damage anything while doing it all yourself ? Like the screen scratches, or something else ? Sorry, for asking these... Thanks in advance :good:
Click to expand...
Click to collapse
I haven't re-glued the speaker covers back on yet so I dont know if they will be perfectly flush or not, although they still look flat so I think it will look good.
The only damage is a slight bend in the frame on the screen side of the sim tray slot. The metal is thin, and I pried against it to get the hardware out of the frame. That is why I recommended to start from the bottom when separating the two. Doing this should allow others to avoid this problem. It is slight, maybe 1/4mm gap where it used to be flush along the side of the screen above the sim tray.
Otherwise everything was smooth. The screen/frame etc are still mint.
bookfast said:
I haven't re-glued the speaker covers back on yet so I dont know if they will be perfectly flush or not, although they still look flat so I think it will look good.
The only damage is a slight bend in the frame on the screen side of the sim tray slot. The metal is thin, and I pried against it to get the hardware out of the frame. That is why I recommended to start from the bottom when separating the two. Doing this should allow others to avoid this problem. It is slight, maybe 1/4mm gap where it used to be flush along the side of the screen above the sim tray.
Otherwise everything was smooth. The screen/frame etc are still mint.
Click to expand...
Click to collapse
Cool, you've done it like a pro then. :good: .Any picture describing the damage would be helpful, if you can provide. Is the display mint ? No scuffs/scratches on it ? But, my speaker grills were damaged onto the edges after the repair was carried out. Does yours show the same sign ? I don't mean the flatness of the grills, but the damage that should be done, while prying out the grills. A picture showing your damage would be helpful to me. I could do the same, if you insist. Thanks ! :good:
Mine is busted. But I cannot find the PCB. The link in the op is dead.
Any ideas?
http://www.witrigs.com/oem-charging-port-flex-for-htc-one-m8
bookfast said:
http://www.witrigs.com/oem-charging-port-flex-for-htc-one-m8
Click to expand...
Click to collapse
I actually got one off eBay for $17.21. Works perfectly.
Just wondering....
Sounds like you were able to avoid some steps in the teardown guide, if I recall it was damn near a total disassemble. Do you have a lot of experience with phones? I want to fix mine, but don't need a tedious project right now. If I repair mine I'd like to put a mini USB in place of the micro if possible, I've seen too many damaged micro usb to trust or like them. As for the speaker grills, if you're picky buy replacements, they're cheap.
microphone on charging port?
bookfast said:
Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
link
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
Click to expand...
Click to collapse
My HTC M8's main call microphone has stopped working, and through searches on Google it seems that perhaps that this mic (first mic, non-speakerphone mic) is built into the charging port. Is this the case? I cannot find anything that explicitly says this, and I'd love to get the phone back in working condition.
dm8233 said:
My HTC M8's main call microphone has stopped working, and through searches on Google it seems that perhaps that this mic (first mic, non-speakerphone mic) is built into the charging port. Is this the case? I cannot find anything that explicitly says this, and I'd love to get the phone back in working condition.
Click to expand...
Click to collapse
I too am also curious if the mic is on the usb part because my mic doesnt wrk when i make calls.
Will replacing the usb port fix the problem?
Harvey02 said:
I too am also curious if the mic is on the usb part because my mic doesnt wrk when i make calls.
Will replacing the usb port fix the problem?
Click to expand...
Click to collapse
I called HTC, the mic is on the USB port, although you should make sure that it's not a software issue first. There are several threads on the internet easily found through Google which discuss doing a factory reset to resolve this if it turns out to be a software problem.
Thanks for your reply. I did a factory reset when I got the phone but it still doesn't work. Does that mean it's not a software problem and that if I replace the usb it should work?
Harvey02 said:
Thanks for your reply. I did a factory reset when I got the phone but it still doesn't work. Does that mean it's not a software problem and that if I replace the usb it should work?
Click to expand...
Click to collapse
I would think so, yes.
Thanks! Do you know of any online source confirming that?
Harvey02 said:
Thanks! Do you know of any online source confirming that?
Click to expand...
Click to collapse
No, but from what I've studied about it, it should work. Feel free to contact HTC, they actually have a live chat available somewhere on their website. Good luck to you.
Very interesting, I contacted htc and we went through diagnostics together and the rep said that I have to send it in. I asked him if the mic was on the usb assembly and he said that it wasn't and rather it was on the motherboard, and I clarified that we were talking about the primary mic which is located near the usb port. Confusing bec everywhere I saw online said that the mic is on the usb assembly. Go figure!
Harvey02 said:
Very interesting, I contacted htc and we went through diagnostics together and the rep said that I have to send it in. I asked him if the mic was on the usb assembly and he said that it wasn't and rather it was on the motherboard, and I clarified that we were talking about the primary mic which is located near the usb port. Confusing bec everywhere I saw online said that the mic is on the usb assembly. Go figure!
Click to expand...
Click to collapse
What did you end up doing? Did you discover if it was on the motherboard or the part with the USB port? I've waited a while to repair mine for other reasons, and I am now prepared to fix it. Any information would be helpful.
Just a few notes on my own experience.
I replaced the screen in my friend's M8 a few months ago. Seemed like everything went ok, except after I got done, the mic didn't work anymore. This is strange because it worked fine before, and all I did was remove/replace the circuit board in the process (yes, the small one at the bottom with the uUSB port). However, the upper rear microphone was still working I believe, because people on the other end of the line could still hear if the phone was put into speakerphone mode. I don't know why it would stop working all of a sudden.... Ran the HTC audio test using *#*#3424*#* to confirm main mic wasn't working and that the aux rear mic was.
Fast forward to this week, with my own M8. The uUSB connector was going bad, and I was having trouble charging, so I figured it was time to replace that circuit board. Ordered a new one and replaced, but when I got it back together, the USB port was fine of course, but my mic wasn't working now, just like my friends! On top of that, the headphone jack didn't work at all. Most likely the "cable inserted" signal wasn't getting back up to the motherboard, but didn't check. So pissed off. Also, the new board I got didn't have the bottom left RF connector/circuitry populated. Thinking from research that it might be for the GPS? I should have tested when the board was in there, but didn't. Fixed a bad solder joint on the original board's uUSB connector, which helped, but still charging is a bit messed up. I'd rather have a working mic and headphone jack and have to play with the cable to get to charge for a while until I get another board (from another supplier, jerks).
Yes, the mic is the small chip on the very left side of the board. It has a hole underneath the chip, going through the board and to the front face to receive the acoustics.
I don't know why the mic not working is so common after an HTC One M8 tear down, as it seems many others are having the same issue. One theory I have is that pulling the circuit board from the motherboard while power is still applied (not unplugging the battery first) might be jacking the microphone somehow. Just a theory, but I'd recommend to be safe that anyone replacing the board should unplug the battery cable before replacing the USB/mic circuit board.
I'd just like to chime in to say that I've read about some people having problems with the mic not working after replacing the USB board. From what I understand, there are two different versions of it, and replacing it with the wrong one can cause that very issue. You should look into it.
EDIT: Source - http://www.witrigs.com/blog/htc-one-m8-audio-jack-not-work-after-charging-board-replacement/
Mic broken after USB repair
Old thread but I have the same problem. Replaced USB board and now my mic does not work. However I am pretty certain I did order the correct board (had 2x connectors for my Verizon HTC m8). And my microphone jack work great which others indicate is often broken along with the mic. Anyone have any workarounds?
To cut the long story short, firstly the fast charging stopped working, and now I can't connect my P2 (p2a42 exactly according to my phone) to my computer.
So I came to a conclusion that there's something wrong with the usb port/board. Ordered a new one from UK. BUT when I disassembled my device, I noticed some differences between the replacement and original part. On the original I have four rectangular contact surfaces on one side of the board, but in the replacement, there's only two, so I'm not sure if this is going to work
Well, I went on to ebay once again, and looked for a picture that shows exactly the same board as the original part. Bought it and when it arrived, its actually just like the one replacement part I got earlier
So maybe it'll work though it doesn't look like it would?
(sorry can't post pictures cause I'm new here)