Related
Before you start, you will need to set up your computer to properly recognize the phone. You probably did this when rooting originally, but just in case... Install SDK tools for Android, Java runtime, and HTC Sync.
About HTC Sync: The only reason you need HTC Sync installed is for the USB drivers that come with it. But the program itself has been known to cause conflicts. Make sure that HTC Sync is not running in the background by opening Task Manager in Windows and killing it if you find it lurking in there.
Here we go:
1. Download the correct RUU (ROM Update Utility) for your device from androidfiles.org. Make sure you download a Primo_C RUU for a CDMA device (no sim card) or a Primo_U RUU for a GSM device (uses a sim card)!! Also make sure you get the correct RUU for your carrier.
2. Charge the battery above 50% or for at least one hour. If the battery dies during the flashing process, you could hard brick the phone!
3. Run the RUU until the wizard comes up. While the RUU wizard is open, find the temporary folder it created. (Open Explorer in Windows and type %temp% in the navigation bar.) There will be two folders with long encrypted names. In one of them you will find ROM.zip. Open it with 7zip and extract recovery.img or recovery_signed.img. Put it in the location were you've installed Android SDK tools. This is the stock HTC Recovery and it is needed to run the RUU.
4. Boot the phone into bootloader (power off, hold down volume and press power) and highlight FASTBOOT using the volume rocker and pressing power. Then connect the USB cable. You should see FASTBOOT USB.
5. Open a command prompt in Windows and navigate to the folder where you installed Android SDK tools. Flash the stock recovery extracted in step 3 above using the following command:
Code:
fastboot flash recovery recovery.img
or
Code:
fastboot flash recovery recovery_signed.img
6. Relock the bootloader using the following command:
Code:
fastboot oem lock
7. Re-run the RUU. It will restore the device to it's original condition, locked (though *** RELOCKED ***) and unrooted.
Once the install is done you'll have unlock the bootloader again using the token you already have from the first time, reflash CWM Recovery and re-root. All this will be 10x easier than the first time.
If you do re-root your phone, be 100% you backup the stock ROM in ClockworkMod Recovery before making changes!
Hi
Thanks for that perfect decsription exactly when I needed it
I just had a weired effect with my new windows 7 laptop that I want to share.
I installed the USB drivers and "fastboot devices" showed my HTC fine
but even flashing the stock recovery image was not working.
So it was stucking in the "Sending" part and never continued.
I then moved to my old laptop with Vista did exactly the same things
and there it worked without problems.
I disabled virus scanner, checked for htsync and used the original USB cable
without success.
But now I know why I normally never touch Windows and only
work on linux
Regards
max
---------- Post added at 11:19 PM ---------- Previous post was at 10:33 PM ----------
Hi
CafeKampuchia said:
If you do re-root your phone, be 100% you backup the stock ROM in ClockworkMod Recovery before making changes!
Click to expand...
Click to collapse
I have done that now - compared to my first "try"
Regards
max
hi. thanks for the tips.
however when i do this, i get an error "FAILED <remote: signature verify fail>
Any suggestions?
ur RUU and CID is diff...
ryanlow134 said:
ur RUU and CID is diff...
Click to expand...
Click to collapse
and... how do i make them the same?
lcavada said:
and... how do i make them the same?
Click to expand...
Click to collapse
Use the correct RUU package for your device
regards
max
Another way of saying it is that you downloaded the wrong RUU for your device.
not working
it keeps on saying waiting for device n does not proceed further
i tried installing the drivers again but that doesnt help either
pls help me out
I use fastboot flasher for this.. this tool is good .
sush93 said:
it keeps on saying waiting for device n does not proceed further
i tried installing the drivers again but that doesnt help either
pls help me out
Click to expand...
Click to collapse
"Waiting for Device" at fastboot usually related to bootloader driver. You need Android USB Driver
See : http://developer.android.com/sdk/win-usb.html
Hi folks,
I've bought my One V in late may and I had 2.08 ROM.
Now I've tested some roms and I wanted to revert back to stock rom.
I've downloaded RUU_PRIMO_U_ICS_40A_HTC_Europe_2.08.401.2_Radio_20.72.30.0833U_3831.17.00.18_M_release_263376_signed, and got recovery_signed and boot_signed images. Then I've went to fastboot, did flash recovery and boot partitions, and oem locked bootloader. Afterwards I booted my phone and entered PIN. Then I fired up RUU*.exe file, and I have 155 error. What the heck? Something I missed?
greetings!
run the ruu in hboot..
Sent from my HTC One V
thevilish said:
Hi folks,
I've bought my One V in late may and I had 2.08 ROM.
Now I've tested some roms and I wanted to revert back to stock rom.
I've downloaded RUU_PRIMO_U_ICS_40A_HTC_Europe_2.08.401.2_Radio_20.72.30.0833U_3831.17.00.18_M_release_263376_signed, and got recovery_signed and boot_signed images. Then I've went to fastboot, did flash recovery and boot partitions, and oem locked bootloader. Afterwards I booted my phone and entered PIN. Then I fired up RUU*.exe file, and I have 155 error. What the heck? Something I missed?
greetings!
Click to expand...
Click to collapse
Flashing RUU to revert to stock
- you must have the correct RUU for your device.
- if you are not sure, download CID Getter from Play Store and run it, it will show your CID.
- with your CID, you may be able to find a correct RUU for your device
then (even though some people may not agree with this, but this will bring no harm and it is noob-proof) do this:
1- flash a stock recovery.img
fastboot flash recovery recovery_signed.img
fastboot reboot-bootloader
fastboot erase cache
2- flash a stock boot.img
fastboot flash boot boot_signed.img
fastboot reboot-bootloader
fastboot erase cache
3- re-lock bootloader
fastboot oem lock
fastboot reboot-bootloader
fastboot erase cache
4- flash RUU
NOTE: There is no boot/reboot and enter pin in between.
paarthdesai said:
run the ruu in hboot..
Sent from my HTC One V
Click to expand...
Click to collapse
I've done this before and didn't succeeded, but now it works! Magic
Thanks a lot!
help
CafeKampuchia said:
Before you start, you will need to set up your computer to properly recognize the phone. You probably did this when rooting originally, but just in case... Install SDK tools for Android, Java runtime, and HTC Sync.
About HTC Sync: The only reason you need HTC Sync installed is for the USB drivers that come with it. But the program itself has been known to cause conflicts. Make sure that HTC Sync is not running in the background by opening Task Manager in Windows and killing it if you find it lurking in there.
Here we go:
1. Download the correct RUU for your device from Football's Primo Shipped ROM Collection.
2. Charge the battery above 50% or for at least one hour. If the battery dies during the flashing process, you could hard brick the phone!
3. Run the RUU until the wizard comes up. While the RUU wizard is open, find the temporary folder it created. (Open Explorer in Windows and type %temp% in the navigation bar.) There will be two folders with long encrypted names. In one of them you will find ROM.zip. Open it with 7zip and extract recovery.img or recovery_signed.img. Put it in the location were you've installed Android SDK tools. This is the stock HTC Recovery and it is needed to run the RUU.
4. Boot the phone into bootloader (power off, hold down volume and press power) and highlight FASTBOOT/B] using the volume rocker and pressing power. Then connect the USB cable. You should see FASTBOOT USB.
5. Open a command prompt in Windows and navigate to the folder where you installed Android SDK tools. Flash the stock recovery extracted in step 3 above using the following command:
Code:
fastboot flash recovery recovery.img
or
Code:
fastboot flash recovery recovery_signed.img
6. Relock the bootloader using the following command:
Code:
fastboot oem lock
7. Re-run the RUU. It will restore the device to it's original condition, locked (though *** RELOCKED ***) and unrooted.
Once the install is done you'll have unlock the bootloader again using the token you already have from the first time, reflash CWM Recovery and re-root. All this will be 10x easier than the first time.
If you do re-root your phone, be 100% you backup the stock ROM in ClockworkMod Recovery before making changes!
Click to expand...
Click to collapse
PLEASE HELP!
The 5th point does not work for me. I can not run the code.
What can i do?
what do you mean by navigate to the folder where you installed sdk?
brandoncoronado said:
what do you mean by navigate to the folder where you installed sdk?
Click to expand...
Click to collapse
It means that if you installed SDK in c:/android, then u must type.in the command prompt: cd c:/android and hit enter
Cheers
Sent from my HTC One V using xda app-developers app
brandoncoronado said:
what do you mean by navigate to the folder where you installed sdk?
Click to expand...
Click to collapse
where the fastboot.exe is located and stock recovery must be in the same folder for the command to work
[ask] Error 155
hey guys, ive been reading all tutorial for reverting to stock RUU.
the first time i tried, it works prefectly.
then after a few weeks, i tried to revert to stock RUU, it failed .
it show error 155.
i already flash the boot , recovery that i found inside the stock RUU, also I've relock the phone.
but when i relock the phone, it show "info Lock successfully , status read failed no such file / directory"
when i enter bootloader, it show that my device already "relocked"
does the relocked proses is successfully ?
iam running PrimoU 2.09.707.1 with stock bootloader, CWM recovery, and rooted ..
I did exactly as it is mentioned but at the end where there is vertical progress bar it gives me an error of customer Id... Failed to update. What shud i do. How do I check what my customer Id is I can't Download it from play store coz can't boot into normal screen... How do I make ruu and cid same.
Sent from my Galaxy Nexus using xda app-developers app
Hey all, I dont usually post questions, cause I usually am able to find all my answers, but this time i really hit a stump. not sure if its just cause my case is unique.
I have a HTC__622 (so JB compatible), with HBOOT 0.43 running Android Revolution 9.7.2, and im looking to upgrade to JB. However, despite many guides and tutorials, I can't seem to get past updating my HBOOT. Let me list out what I've done (I was following http://forum.xda-developers.com/showthread.php?t=1660807, following method 2/3, cause i haven't cooked a rom since windows mobile LOL)
1-downloaded "RUU_ENDEAVOR_U_ICS_40_hTC_Asia_HK_1.29.708.15_Radio_2.1204.122.17_release_268338_signed" (my original one was 1.29.708.2)
2-extracted rom.zip from the RUU, and copied over boot-signed.img, system.img, recovery-signed.img
3-flashed boot-signed.img, and recovery-signed.img. system.img failed.
4-relocked bootloader
5-this is where i get stuck, the RUU cannot detect my phone in fastboot mode and so I cant run the RUU.exe.
anyone got any ideas as to why i can't run RUU.exe from my comp while my phone is in fastboot mode? thanks in advance!
I have no idea what you are doing. To install an RUU:
fastboot oem lock
Run RUU.
All this extracting and flashing is madness.
When you boot into bootloader, what does it say on the screen?
BenPope said:
I have no idea what you are doing. To install an RUU:
fastboot oem lock
Run RUU.
All this extracting and flashing is madness.
When you boot into bootloader, what does it say on the screen?
Click to expand...
Click to collapse
I can relock but I can't boot back into my rom. im stuck in the bootloader. The RUU only detects my phone from normal phone mode.
The first lines on the screen are relocked, security warning, and then my hboot info.
Sent from my HTC One X using xda premium
I have done it yesterday and opend a thread http://forum.xda-developers.com/showthread.php?t=2048646
Only relock stay in fastboot mode and run ruu with admin rights... Than the setup will so the rest for u
Sent from my HTC One X using xda app-developers app
ngy said:
I can relock but I can't boot back into my rom. im stuck in the bootloader. The RUU only detects my phone from normal phone mode.
Click to expand...
Click to collapse
What error do you get in fastboot mode?
zottel1993 said:
I have done it yesterday and opend a thread http://forum.xda-developers.com/showthread.php?t=2048646
Only relock stay in fastboot mode and run ruu with admin rights... Than the setup will so the rest for u
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
thanks man, i've looked at that thread though, i dont see what i'm missing. how did you run the ruu in fastboot mode?
BenPope said:
What error do you get in fastboot mode?
Click to expand...
Click to collapse
the error i get is the ruu cannot detect the phone through usb (while phone is in fastboot mode). and i cannot run the ruu while phone is in normal mode because i can't boot in normal mode when i lock my bootloader.
Does the phone say fastboot USB when you have it in fastboot/bootloader
Then try fastboot devices first to see if your serial comes up ! If it does you can run the ruu.exe from the pc with admin rights.....
Should do the trick
Ok I would try to do everything from the beginning.
To make it easier and faster you can use the script form that thread:
http://forum.xda-developers.com/showthread.php?t=1924003&highlight=jbfwflasher
Then you don't need to install RUU.
Remember to place in the folder boot.img from the rom which you want to flash later.
Have a good fun
Follow this it might give you an idea where to start and what to do
http://forum.xda-developers.com/showthread.php?t=2018040
say thanks if i helped you
MarcelHofs said:
Does the phone say fastboot USB when you have it in fastboot/bootloader
Then try fastboot devices first to see if your serial comes up ! If it does you can run the ruu.exe from the pc with admin rights.....
Should do the trick
Click to expand...
Click to collapse
i already have, i always fastboot devices first to check to make sure my device is connected. on my phone it does say fastboot usb, and i can run fastboot commands on it. and i've ran RUU.exe with admin rights, but still does not detect the phone and gives me a usb connection error.
mrdelook said:
Ok I would try to do everything from the beginning.
To make it easier and faster you can use the script form that thread:
http://forum.xda-developers.com/showthread.php?t=1924003&highlight=jbfwflasher
Then you don't need to install RUU.
Remember to place in the folder boot.img from the rom which you want to flash later.
Have a good fun
Click to expand...
Click to collapse
au contraire, i also have tried using this tool, but if you look carefully, its meant for hboot versions higher than 0.43, which i have. it just points me to download an RUU.exe for my phone (which I already have)
Onexed said:
Follow this it might give you an idea where to start and what to do
http://forum.xda-developers.com/showthread.php?t=2018040
say thanks if i helped you
Click to expand...
Click to collapse
hmm, so you're saying I just need to flash firmware.zip (for my HTC__622 of course), to get the hboot 1.36? i'll give that a shot and report back.
--update 1--
alright so after trying to just flash the new hboot 1.36 (from firmware.zip), i am met with this:
E:\Utilities\Android\One X\JBFWTOOL20>fastboot flash zip firmware-622.zip
sending 'zip' (12875 KB)...
OKAY [ 1.647s]
writing 'zip'...
(bootloader) adopting the signature contained in this image...
(bootloader) signature checking...
(bootloader) checking model ID...
(bootloader) checking custom ID...
FAILED (remote: 42 custom id check fail)
finished. total time: 3.130s
how did you flash it and make it work?
--update 2--
I must've downloaded the wrong (or renamed the wrong) firmware.zip file, i just redownloaded and bam everything works. thanks a lot onexed, that did help. basically, even if you're on 0.43, just flash the firmware.zip for your phone, and get onto a newer hboot, and all is well. thanks!
Welcome i'm glad it worked out for you enjoy jellybean
hello guys, i have a problem using RUU to revert my phone back to stock, i searched for a solution on xda forum and google for few hours now but nothing was exacly my problem. i am sorry if i missed vital information, this is my first android phone and i am still trying to learn and understand how it works.
CID 004 primou
i tried 2 different ruu versons for this CID. before using each i did the following steps
flashed boot from archive, flashed recovery from archive, relocked the bootloader.
-http://forum.xda-developers.com/showpost.php?p=30966084&postcount=114
first gave the error 155 due to the HBOOT being of a more recent version than the ruu (not sure if i understood well the error)
http://forum.xda-developers.com/showpost.php?p=30994089&postcount=121
on the second ruu *latest, i did same steps as before, unlocked bootloader, flashed boot, flashed recovery, relocked, but the ruu gives the error 170 ( device not connected) but i am 100% sure it is correctly connected into fastboot because it responds to One_V_All-In-One_Kit and it was recognized by the previous ruu.
i am using windows 8 pro and i have installed the ADB interface using the SDK google driver, this method to be exact http://forum.xda-developers.com/showthread.php?t=2088896
Can you run this script and let us know the result because CID 004 is different from 044.
See this post for the script : http://forum.xda-developers.com/showpost.php?p=36514545&postcount=15
And this post reason for error 170 : http://forum.xda-developers.com/showpost.php?p=36515756&postcount=22
hello, thanks for helping me,
i do not have any USB 3.0 ports on my PC, and the battery is at about 60%
the script you gave me told me this:
C:\Users\Draghici\Desktop\CID_checker_2>call fastboot getvar cid
cid: HTC__044
finished. total time: 0.001s
There is no need to flash boot.img and recovery.img, just a relocked bootloader is needed.
Just follow this step : http://forum.xda-developers.com/showpost.php?p=36515523&postcount=18
Most important is make sure your device is put on fastboot usb mode not hboot usb mode. (Another common error for usb connection problem when flashing RUU)
And use the latest RUU RUU_PRIMO_U_ICS_40A_hTC_Asia_WWE_2.22.707.2_Radio_ 20.76.30.0835U_3831.19.00.120_release_274703_signed.exe
ckpv5 said:
There is no need to flash boot.img and recovery.img, just a relocked bootloader is needed.
Just follow this step : http://forum.xda-developers.com/showpost.php?p=36515523&postcount=18
Most important is make sure your device is put on fastboot usb mode not hboot usb mode. (Another common error for usb connection problem when flashing RUU)
And use the latest RUU RUU_PRIMO_U_ICS_40A_hTC_Asia_WWE_2.22.707.2_Radio_ 20.76.30.0835U_3831.19.00.120_release_274703_signed.exe
Click to expand...
Click to collapse
sure i will do it right now, but i am 100% sure i relocked it correctly, the phone was in fastboot USB (red text) every time, and after each flash of boot/recovery, i relocked it, it told me in pink text in the recovery mode "RELOCKED"
but one more thing to add, when the RUU install failed on my phone screen it told me that the HBOOT version is too recent or something like that
hboot too recent if you flash 2.09 RUU (for hboot 1.17) but your hboot maybe 1.18 (2.22 RUU).
Unless there is a further update that I may missed, what hboot number is written on the bootloader ?
ckpv5 said:
hboot too recent if you flash 2.09 RUU (for hboot 1.17) but your hboot maybe 1.18 (2.22 RUU).
Unless there is a further update that I may missed, what hboot number is written on the bootloader ?
Click to expand...
Click to collapse
i have the 1.18, so i need to use
RUU_PRIMO_U_ICS_40A_hTC_Asia_WWE_2.22.707.2_Radio_20.76.30.0835U_3831.19.00.120_release_274703_signed
the one that gives me the error 170. i have 3 drivers provided by android SDK named
Android ADB Interface
Android Bootloader Interface
Android Composite Interface
each of them work with the 2.09 RUU and with all in one tool but none of them worked on 2.22 RUU.
You need HTC USB driver.
I'm using the driver from this HTC Sync Manager. It works nicely for Win 8 pro.
Install the HTC Sync Manager, it will install the necessary driver and you can remove the HTC Sync Manager later on but keep the driver.
http://www.htc.com/www/software/htc-sync-manager/
ckpv5 said:
You need HTC USB driver.
I'm using the driver from this HTC Sync Manager. It works nicely for Win 8 pro.
Install the HTC Sync Manager, it will install the necessary driver and you can remove the HTC Sync Manager later on but keep the driver.
http://www.htc.com/www/software/htc-sync-manager/
Click to expand...
Click to collapse
sorry for the late rly, I think I got some progress, I did the next steps.
went to device manager and uninstalled google android sdk driver, went to HTC Sync installation folder (I had it installed at first try but it did not pass my mind to show windows the location where it was installed, anyway...) and I installed the windows 7 driver, the windows 8 do not work for some reason, right now I can see the green progress bar on my phone so I guess it worked.
thanks a lot
I will ofc hit the "thanks" button on your posts here.
Yep...that's a good progress... it will be a successful flash
Please help , ITS VERY URGENT...
My HTC ONE X is rooted unlocked and S-OFF
I was about to install ARHD latest ROM. I went to flash boot.img first.
The moment I clicked on "install-boot-windows.bat" in FASTBOOT USB mode, everything just froze.
No button works. My computer gives a message of " USB DEVICE NOT RECOGNISED" .
When I try to give any command from Fastboot or ALL IN ONE TOOL KIT, IT SAYS " waiting for device" .
My phone is stuck at FASTBOOT USB screen.
please help as fast as possible. I can't wait for my device to die.
I am attaching the snapshot of my current phone screen...
When I type "adb devices" , it doesn't show any device
when i type command " adb reboot recovery ", it says device not found.
Now what to do??
aypee3 said:
When I type "adb devices" , it doesn't show any device
when i type command " adb reboot recovery ", it says device not found.
Now what to do??
Click to expand...
Click to collapse
yes in bootloader work only fastboot no adb. go in recovery and flash ARHD again. And you are s-off you can run any RUU. And if you use search button you will find all the info where you need
Thant said:
yes in bootloader work only fastboot no adb. go in recovery and flash ARHD again. And you are s-off you can run any RUU. And if you use search button you will find all the info where you need
Click to expand...
Click to collapse
Thanks for your reply.
But then , How do I flash boot.img for ARHD ?
Since I had followed all the steps properly and in sequence.
When I tried flashing boot.img from my laptop previously, my device crashed and then no button worked . My laptop kept giving a message that USB DEVICE NOT RECOGNISED .
Also, unless I flash boot.img , how can I flash the ROM?
Do you have any link or clue?
aypee3 said:
Thanks for your reply.
But then , How do I flash boot.img for ARHD ?
Since I had followed all the steps properly and in sequence.
When I tried flashing boot.img from my laptop previously, my device crashed and then no button worked . My laptop kept giving a message that USB DEVICE NOT RECOGNISED .
Also, unless I flash boot.img , how can I flash the ROM?
Do you have any link or clue?
Click to expand...
Click to collapse
you can flash the boot.img with the command fastboot flash boot boot.img Try on different port or install latest htc drivers. You can flash official rom with RUU download RUU reloack the bootloader and run the RUU then you will be complete stock ROM.
Any link for what, I give you a clue in my 2 post.
Thant said:
you can flash the boot.img with the command fastboot flash boot boot.img Try on different port or install latest htc drivers. You can flash official rom with RUU download RUU reloack the bootloader and run the RUU then you will be complete stock ROM.
Any link for what, I give you a clue in my 2 post.
Click to expand...
Click to collapse
The only problem is that my laptop doesn't recognise my phone. So commands hang and my phone freezes .I have tried all the ports while deleting HTC SYNC , installing different drivers from so many different sites/posts one by one . Finally was able to reboot the phone . I will give it a try with another laptop or using a different datacable . Unless my laptop recognises my phone, properly , I don't think any command will work.
I rooted it and flash custom rom "InsertCoin 4.1.1'. Still S-on. Firewater method doesn't work. And Sunshine method also doesn't work because of the custom rom. It requires stock sense,near stock rom.
I want my phone way it was before I root the device. (Stock m8)
My CID SPCS_004
firmware 2.16.654.4
Please help me....
Ruu in Android development will do the trick for you
tjeeeeee said:
Ruu in Android development will do the trick for you
Click to expand...
Click to collapse
Never seen a 2.16.654 ruu there ! Can you point me to it please. As for additional information :
He can't install any other ruu than a 2.16.654 or higher one since he has no S-OFF.
kelum17 said:
I rooted it and flash custom rom "InsertCoin 4.1.1'. Still S-on. Firewater method doesn't work. And Sunshine method also doesn't work because of the custom rom. It requires stock sense,near stock rom.
I want my phone way it was before I root the device. (Stock m8)
My CID SPCS_004
firmware 2.16.654.4
Please help me....
Click to expand...
Click to collapse
Check for maximus or arhd (NOT the lollipop versions but a slight older one) in the dev section or get a new stock backup matching your version number in the general section - collection of firmwares, stock backups and more by @exocetdj
And if that doesn't give you the correct steps and files than try the specific Sprint M8 support subforum
http://forum.xda-developers.com/showthread.php?t=2729173
It's listed under "previous" in the main post
tjeeeeee said:
http://forum.xda-developers.com/showthread.php?t=2729173
It's listed under "previous" in the main post
Click to expand...
Click to collapse
Ah i see in the Sprint section. Maybe it's good to mention that too in the first reply because this is the international section and therefore doesn't hold Sprint ruu files. So that confused me a bit. Thanks for the link
My bad I didn't realize that
Thanks both. Really appreciated your advice. I tried steps in below link
http://forum.xda-developers.com/showthread.php?t=2729173
Flash firmware via HBOOT
Flash Firmware via fastboot
I grabbed the firmware in https://www.androidfilehost.com/?fid=23578570567713359
But both ways failed.
Please let me know how to flash RUU ?
are there any differences between RUU.exe and RUU.zip ?
You flash RUU via computer
tjeeeeee said:
My bad I didn't realize that
Click to expand...
Click to collapse
tjeeeeee said:
You flash RUU via computer
Click to expand...
Click to collapse
Tried both ways below
download 2.16.654.4 RUU.zip
extract it and found 0P6BIMG.zip
move it to sd card and reboot via bootloader
Nothing happends
rename the RUU.zip file as firmware.zip
place it in adb directory
boot the phone into hboot mode and plug into pc and choose fastboot. it turns to fastboot usb
right click on the adb directory with shift and open the command promt
typed Fastboot oem rebootRUU
when see the black screen w/ HTC, typed Fastboot flash zip firmware.zip
it always gives error 99
Please help me to sort out this thing
kelum17 said:
Tried both ways below
download 2.16.654.4 RUU.zip
extract it and found 0P6BIMG.zip
move it to sd card and reboot via bootloader
Nothing happends
rename the RUU.zip file as firmware.zip
place it in adb directory
boot the phone into hboot mode and plug into pc and choose fastboot. it turns to fastboot usb
right click on the adb directory with shift and open the command promt
typed Fastboot oem rebootRUU
when see the black screen w/ HTC, typed Fastboot flash zip firmware.zip
it always gives error 99
Please help me to sort out this thing
Click to expand...
Click to collapse
Run Ruu exe through pc itll reset phone completely stock
You can't apply any of the above methods due to having s-on you have to Ruu using the application via computer to complete stock then you'll be able to update like usual for otas
tjeeeeee said:
Run Ruu exe through pc itll reset phone completely stock
You can't apply any of the above methods due to having s-on you have to Ruu using the application via computer to complete stock then you'll be able to update like usual for otas
Click to expand...
Click to collapse
Do I need run 2.16.654.4 RUU.exe file ?
Yes also don't forget to relock bootloader as well
tjeeeeee said:
Yes also don't forget to relock bootloader as well
Click to expand...
Click to collapse
Before I run the RUU.exe do I neet to unlock the bootloader (using fastboot oem lock command) ?
Or run normally ?
And how to relock the bootloader ?
kelum17 said:
Before I run the RUU.exe do I neet to unlock the bootloader (using fastboot oem lock command) ?
Or run normally ?
And how to relock the bootloader ?
Click to expand...
Click to collapse
Fastboot oem lock
That's the command to relock it.
Mr Hofs said:
Fastboot oem lock
That's the command to relock it.
Click to expand...
Click to collapse
Should I need to unlock the bootloader before run RUU.exe ?
How could I do that ?
Please help
kelum17 said:
Should I need to unlock the bootloader before run RUU.exe ?
How could I do that ?
Please help
Click to expand...
Click to collapse
If you have a s-on device you need to relock the bootloader before running the ruu.exe !
Mr Hofs said:
If you have a s-on device you need to relock the bootloader before running the ruu.exe !
Click to expand...
Click to collapse
Please advice below steps are correct
turn off the phone and press volume down button with power button
when highlighted as HBOOT plug device to the pc
then press volume down button and select fastboot
when it turns to fasboot usb right clock on the adb directory with shift, select command promt
and type 'fastboot oem lock' command
Then how I run the RUU.exe ?
please advice me step by step
kelum17 said:
Please advice below steps are correct
turn off the phone and press volume down button with power button
when highlighted as HBOOT plug device to the pc
then press volume down button and select fastboot
when it turns to fasboot usb right clock on the adb directory with shift, select command promt
and type 'fastboot oem lock' command
Then how I run the RUU.exe ?
please advice me step by step
Click to expand...
Click to collapse
uhm well, you double click the ruu.exe on the pc. That should do the trick
Hi
I relock the bootloader and did the prrevious steps. Now its worked.
Now it shows "RELOCKED" in the bootloader menu.
Is it the normal sign ?
Yes as you are s-on that's normal. Only with s-off you can change those flags to LOCKED