Develop Bugs

HELP!!! What does this mean?

If Rooted
Make sure you have a recent Titanium Bakcup
Download the file PB31IMG.zip and place it in the root of you SD card
Power off the phone and then press and hold power + volume down to boot into the boot loader
Press and hold volume down and the power button to boot into HBoot
The phone will find, load, and check PB31IMG.zip. It will then ask you if you would like to update using the file
Press volume up to update the phone
Reboot the phone – you are now back to stock
Boot the phone, go through the setup (but don’t bother to set anything) and remove PB31IMG.zip from your SD card.
Download the file dinc_ota.zip, rename it to update.zip and place it in the root of your SD card.
Reboot into recovery (turn on USB debugging and run “adb reboot recovery” or power down the phone and then press and hold power and volume down)
Press volume down once, then press the power button to select Recovery
Press power and volume up to bring up the recovery menu.
Use the volume rocker to highlight apply update.zip, then power to run it
Reboot the phone when prompted.
Go to Settings > About phone > Software information > Baseband version and verify that it’s 2.05.00.06.11.
You can now re-root your phone by running Unrevoked 3 and make a new Stock + OTA Antenna backup in nandroid.
I was following these instructions to update my radio... I am at the point where I've put the update.zip file on my sd card and I am rebooting into recovery. My device now displays a black screen with a red triangle/! over a picture of a device... I pulled the battery once and the device powered on, so I tried again and I have the same red triangle/! over a picture of a device... WHAT DO I DO?

Vol up + power button
Sent from my ADR6300 using XDA App

Thank you... that worked

Haha.
Sent from my ADR6300 using XDA App

Recovery menu does not show update...

Trying to a manual update on a stock phone, hold power button and volume up keys get bootloader, reboot, reboot bootloader, power down, select bootloader now I have a menu of fastboot, recovery, clear storage, simlock, hboot usb select recovery and reboots superquick and goes back to the first menu bootloader reboot reboot bootloader power down. Thats it keeps the same cycle, nothing about apply update. What am I missing? This was a replacement phone that came with the OTA update already applied.

Cruzerx said:
Trying to a manual update on a stock phone, hold power button and volume up keys get bootloader, reboot, reboot bootloader, power down, select bootloader now I have a menu of fastboot, recovery, clear storage, simlock, hboot usb select recovery and reboots superquick and goes back to the first menu bootloader reboot reboot bootloader power down. Thats it keeps the same cycle, nothing about apply update.
Click to expand...
Click to collapse
this post makes no sense. if youre trying to do a manual update you go to settings, system updates, and take it from there. if you're not rooted you will not have a recovery image on your phone and can only load stock roms.

this is from another forum:
USB Cable
- Mount phone on EVO (you should see USB icon in status bar at top of your screen on EVO. Pull down status bar and click the USB icon. Mount)
- Copy downloaded file onto SD card listed in My Computer. (Just drag it on there)
- Unmount SD card and unplug USB Cable
- Turn off EVO
- Hold down the VOLUME UP button and push the power button
- Use the VOLUME button to select RECOVERY mode and push the power button to select
- Once in Recovery mode Select “apply update.zip” or “install from .zip” (depending on your recovery image)
DO NOT UNZIP THE FILE
YOU DO NOT NEED ROOT
Is this incorrect? Just trying to install the froyo update file from HTC.

Cruzerx said:
this is from another forum:
USB Cable
- Mount phone on EVO (you should see USB icon in status bar at top of your screen on EVO. Pull down status bar and click the USB icon. Mount)
- Copy downloaded file onto SD card listed in My Computer. (Just drag it on there)
- Unmount SD card and unplug USB Cable
- Turn off EVO
- Hold down the VOLUME UP button and push the power button
- Use the VOLUME button to select RECOVERY mode and push the power button to select
- Once in Recovery mode Select “apply update.zip” or “install from .zip” (depending on your recovery image)
DO NOT UNZIP THE FILE
YOU DO NOT NEED ROOT
Is this incorrect? Just trying to install the froyo update file from HTC.
Click to expand...
Click to collapse
he left a step out. if you are not rooted you will not have a recovery menu. So once you select recovery you will get stuck on a screen. once you are stuck on that screen press volume up and power at the same time (it may take a couple of tries) then an option to apply zip will pop up and it will then install.

thanks p-slim... will give it another go. so far it has just been looping inbetween the menus. thanks again

Well I dont know what went wrong it just kept looping between the menus. I justed rooted it and went on.

after youre done rooting, you need to remove or rename the PC36IMG zip file. otherwise you cant get into recovery.

[Q] how to go in boot menu without pressing volume down key

hi..my desire's volume down key is defective & its not working..
so is there any apps. or any other method to go in boot menu without pressing volume down key.
plz help
i want to install another rom in my phone

push power + vol down!

ashuonweb said:
hi..my desire's volume down key is defective & its not working..
so is there any apps. or any other method to go in boot menu without pressing volume down key.
plz help
i want to install another rom in my phone
Click to expand...
Click to collapse
You should install 'Quick boot' from the market. You need root access to use this app. You can also connect your phone to your PC and use ADB to reboot the phone in bootloader mode with the following adb command: adb reboot bootloader.

You mean the hboot menu? Press and hold back and power button, and when fastboot screen appears, press power button. Now you are in hboot.

You can install "ROM manager" , it can reboot into the Recovery(CWM)

Code:
adb reboot bootloader

thanx to all above for your valuable reply..
but i am having problem that my usb connection get automatically disconnected whenever i click on.exe file of rom
plesae help

ashuonweb said:
thanx to all above for your valuable reply..
but i am having problem that my usb connection get automatically disconnected whenever i click on.exe file of rom
plesae help
Click to expand...
Click to collapse
As far as I know, there isn't any .exe file in an android operating system. And for your problem, you should do something like this:
1. If you're on Windows:
- make sure that you have the android sdk downloaded;
- make sure the drivers for HTC Desire are installed on your pc / laptop
- go to platform-tools, hold the SHIFT button from your keyboard pressed and, while holding it, press the right mouse button in that folder. The right click menu will appear, but having an extra option "Open Command Window Here" or something like that;
- connect your phone cable to your pc / laptop;
- plug the cable into your phone;
- in the command prompt window opened earlier write "adb shell reboot recovery" to go into recovery, "adb shell reboot" to simply reboot or "adb shell reboot bootloader" to boot into the bootloader;
2. If you're on Linux:
- open terminal;
- cd /to/the/android/sdk/path;
- cd /platform-tools;
- use the commands I wrote above, the ones including adb;

If your existing rom allows it, if you press and hold power button, choose restart, then you can get a mini menu with the option to boot into recovery. You can then use the recovery to flash the new rom.
Another option is 4ext recovery - http://forum.xda-developers.com/showthread.php?t=1408936
It will install a new recovery on your phone - but it is pretty cool. You can use the touchscreen to navigate rather than volume buttons (handy if your volume is stuffed) You can also use the app to launch the recovery.

I am also having a similar problem .I was trying to install superuser in a .zip file ,but now I have ended up in a boot loop ,I am not able to go to the boot menu .................
Can anybody help me.

aditya p said:
I am also having a similar problem .I was trying to install superuser in a .zip file ,but now I have ended up in a boot loop ,I am not able to go to the boot menu .................
Can anybody help me.
Click to expand...
Click to collapse
Take the battery out, then boot in hboot (if your volume buttons are not working, press Power+Back button, then select Bootloader), then recovery and restore your backup (you should have done one) or reflash your rom.

ZenFone Go ‏(ZC500TG) Boot Loop How to fix?

Hello,
Recently I got my Device updated to last firmware, and since after all problems started to appear.
I tried to Download last firmware from the page and to manually install it but failed since mobile is not PC can't read the mobile on USB. (zip file doesn't contain recovery.img or system.img)
When I use recovery from boot screen it shows the logo and stuck
Mobile is not rooted or anything, if there's anyway to recover it, I'd be glad to hear it.

zc500tg boot loop
same problem for me after the last update
I can't enter to recovery mode. tried some combination like volume down + power , vol up + power , vol up + vol down in "no command" page but i couldn't see the recovery mode options

hey I found the solution
1. Turn off the phone, either by regular shutdown or by removing and reinserting the battery.
2. Hold volume up+power button until phone vibrates.
3. Phone should boot to Bootloader Mode. In this mode, volume up is select, volume down is "OK".
4. Using volume up, scroll to Recovery Mode and press volume down to confirm.
5. When you see the "No command." icon, hold power, and press volume up once to access Recovery Mode.
6.download the firmware zip file . place the firmware file on your microsd card and insert it to the phone.
Go to recovery mode>choose apply update from sdcards>choose the firmware you copied earlier>then wait for process completed.
If the installation completed choose reboot system firmware.
The asus logo loading will take upto 7-8mins so be patient.

I'm pretty sure he said he had updated to a later ROM, and the bootloader unlocking isn't there(last version was v39, i think).
OP, if you can, try to reboot to recovery mode, it should be able to let you connect the phone as MTP(storage).
Upload an older ROM to the phone, and then use the recovery to update it with the .zip you uploaded.
Hope it helps! Good luck!

Stuck in recovery after ADB with broken power button

Its very complicated. My T705's power button was damaged by water. And i flashed Stock MM rom with odin. It was fine after flashing, the tablet boot into the os properly, work very well in the os.
But then i want to wipe the cache and data after that, so i was using the code"adb reboot to recovery" to get into recovery mode because my power button was broken. (I thought it can be using home button to select in recovery mode)
But the nightmare is i can't select anything in recovery mode which requiring a power button. So i can't wipe the cache, also can't select the option to reboot my tablet...... I've tried to hold both the volume down and home key to go to the download mode menu, and select restart by holding volume down, but it go to recovery again even after removing the battery, i think it's because the adb command.
And the strangest thing is i can't use my volume up button in download mode menu, so sadly i can't flash the rom again,:crying: but the volume up is working well in recovery and in the os......
Is there anyway to prevent the tablet to boot into the recovery again? I'm quite sure it's not the problem when flashing MM rom, the problem should be the adb command makes my tablet boot into recovery until i change the boot setting in recovery mode.

hungpakto said:
Its very complicated. My T705's power button was damaged by water. And i flashed Stock MM rom with odin. It was fine after flashing, the tablet boot into the os properly, work very well in the os.
But then i want to wipe the cache and data after that, so i was using the code"adb reboot to recovery" to get into recovery mode because my power button was broken. (I thought it can be using home button to select in recovery mode)
But the nightmare is i can't select anything in recovery mode which requiring a power button. So i can't wipe the cache, also can't select the option to reboot my tablet...... I've tried to hold both the volume down and home key to go to the download mode menu, and select restart by holding volume down, but it go to recovery again even after removing the battery, i think it's because the adb command.
And the strangest thing is i can't use my volume up button in download mode menu, so sadly i can't flash the rom again,:crying: but the volume up is working well in recovery and in the os......
Is there anyway to prevent the tablet to boot into the recovery again? I'm quite sure it's not the problem when flashing MM rom, the problem should be the adb command makes my tablet boot into recovery until i change the boot setting in recovery mode.
Click to expand...
Click to collapse
Install twrp, you won't need a power button then.

ashyx said:
Install twrp, you won't need a power button then.
Click to expand...
Click to collapse
How to install when this tablet can't do anything now..
Can't select anything now, can't go into the os and use adb to boot into download mode

hungpakto said:
How to install when this tablet can't do anything now..
Can't select anything now, can't go into the os and use adb to boot into download mode
Click to expand...
Click to collapse
If your power button doesn't work how do you turn the device on after removing the battery?

unified android toolkit has a reboot device option...

mordeith said:
unified android toolkit has a reboot device option...
Click to expand...
Click to collapse
That would only work if you could actually use adb.

ashyx said:
That would only work if you could actually use adb.
Click to expand...
Click to collapse
probably would help,if i read all the posts before commentijng...but ive used it on random devices to reboot it..not soleley from adb

ashyx said:
If your power button doesn't work how do you turn the device on after removing the battery?
Click to expand...
Click to collapse
Holding vol down + home key can boot to the download mode menu.
But the device will automatically turn on after inserting the battery, no need to press any button, but the device only boot into recovery after i use the adb boot into recovery command.

hungpakto said:
Holding vol down + home key can boot to the download mode menu.
But the device will automatically turn on after inserting the battery, no need to press any button, but the device only boot into recovery after i use the adb boot into recovery command.
Click to expand...
Click to collapse
If that's the case that means the power button is stuck on or you wouldn't be able to power on or boot to Download mode.
All you need to do is flash the stock firmware or twrp and it will reboot back to the OS.

Hopefully I've got your fix:
When you insert the battery your device boots up, if so, insert the battery and press the correct key combo while the splash screen from logo.bin is showing to boot into the download mode.
After that flash TWRP latest version with Odin. Then when your phone again boots to recovery, chose Reboot -> System to boot Android.
---
If the above isn't applicable and you can start Android somehow, I will download either FlashFire or MobileOdin to flash another recovery/ROM.
Sent using Tapatalk

ashyx said:
If that's the case that means the power button is stuck on or you wouldn't be able to power on or boot to Download mode.
All you need to do is flash the stock firmware or twrp and it will reboot back to the OS.
Click to expand...
Click to collapse
And don't know why the volume up doesn't work in the download mode menu, stuck in the download mode menu and can't select the option "continue" to go into the download mode

hungpakto said:
Holding vol down + home key can boot to the download mode menu.
But the device will automatically turn on after inserting the battery, no need to press any button, but the device only boot into recovery after i use the adb boot into recovery command.
Click to expand...
Click to collapse
lot of problems can be fixed by samsung k300 tool ,disconect phone and start that tool and connect phone again and let the tool find the phone ,if found just click that icon and phone go to download mode and you can flash back stock firmware...that tool dont need adb enable just working usb cable ,i say working cant be fake...