Related
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
On another note - I had purchased a working 2110 with a good mobo to replace this one if the flash is not repairable - is that a difficult procedure? Unfortunately, the 2110 I purchased was not working, but this may still be in the books at a later time, so some info would help.
Thanks!
Rustmonkey said:
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
Click to expand...
Click to collapse
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
reggaepoo said:
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
Click to expand...
Click to collapse
You, my good sir, are a genius - worked great! Fixed BOTH 2110s
tangwd898 said:
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
Click to expand...
Click to collapse
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Rustmonkey said:
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Click to expand...
Click to collapse
really amazing !!!!!!
I just saved my hx2110 as per your step by step instruction now.
Thank you very much.
ok, well, I thought they were fixed... now one of them freezes at the bootup screen, even when I do a clean reset... I've tried reflashing multiple times to no avail... any ideas whats going on?
ok, got everything working - reflashed the non-working one back to an original 2003 rom - which made if freeze at boot - then upgraded it via pre-bl to 1.00.00.L - from here, it wouldn't do anything after filling the bar at the boot screen, but it didn't CRASH (as in lights out) - so I ran the pre-bl again and ran the flash program for 1.00.00.L again WITHOUT swapping between the 2495 and the 2110 - just put the 2110 in pre-bl and away we went - flashed, formatted, and booted - then proceed to upgrade to WM6 via 1.00.00.H --> 1.02.00.H --> WM6 - works GREAT!!!
Thanks for the help everyone!
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Hello,
I have run into some problems with a bricked hx2110.
I was flashing the IPAQ to a new ROM WM5 (Battery was full and I read all the instructions 10 times prior to flashing). While flashing, the progress bar went to 100% then faded out immediately and it wouldn't reset (clean reset). I put the battery in my friends hx3000 series and the battery I used was completely dead. It did flash to 100% though, but not matter how many times I try 1 + 3 + reset, it doesn't reboot. If I can figure out how to get it to boot, that would be great, but I can't get anything to come up with any key combinations.
To this point all I can do is get into Pre-BL mode 1.00.04. I have tried the below scenarios on two machines, both running windows XP SP2 (USB 2.0) with the firewall and virus software disabled.
http://forum.xda-developers.com/showthread.php?t=330382&page=4
1) I have tried the above links directions and used the the Universal Bootloader (Bootloader.exe). It gets to the point where it says "The PDA should be updating now" or something similar but nothing happens. I don't get any errors regarding communications (it sees the device when I hold the "Calendar" button until it says USB; windows then recognizes the device as "HP USB ..." so I know it's communicating).
2) I tried to use the Bootloader_GUI.exe beta so that I can watch the progress indicator but it just sits at 0%. There are no error messages so it is communicating but for some reason, the device won't let it flash (and the flash utility thinks it's doing something).
3) I tried the original ROM flash from HP (SP29856.EXE) and it recognizes the device, but because the current ROM on the PDA is hosed, when it does it's "verifying" process, it comes up with "?" marks as the model number and when it goes to flash it starts at .1% then says "FINISHED" immediately. The ROM utility thinks it flashed it correctly but it didn't flash anything. I'm guessing that the verification of the PDA failed and forced the utility to not flash.
Does anyone have ANY ideas of what to try? I wish I had another HX2000 series PDA and try the "swap" thing prior to hitting the update button but I don't. All I have to work off of it my sad bricked PDA and a full battery (friend keeps charging it). His PDA is an HX3000 series.
Any ideas would be appreciated,
Thanks!
Are you using a the HP flash program that is specified for your device?
2nd - you might be able to use your buddies device in a swap as well - not sure but its worth a shot - use HPs upgrade program, let it verify, then swap your device onto the same cable - overwrite the firmware in the update program for HIS device with firmware compatible with yours and then hit update - let us know if this works...
I am using the "official" HP flash program specific for the HX2110 (from their website - SP29856), bootloader.exe, and bootloader_gui.exe
I wanted to try my friends, but he won't let me touch his because I bricked mine lol (I swore nothing would happen to his but he still won't let me try it).
Anyway, I just copied over the ROM image (from HP) and stripped out the header (now showing 64 bytes before the ECEC). The ROM is for WM2003. I copied the ROM in binary using psdwrite.exe to an 256 MB SD card. As soon as I can get the battery back, I'm going to try to flash it from the SD card. If this fails, I am going to try to play around with MTTY / USB and manually call the ROM flash and see what happens.
Having another HX2000 series would make this easy (maybe a little TO easy )!
Bootloader never worked for me - but if you can get it to manually call the flash, more power to you good luck!
Well it was worth a shot. After spending the better part of the day with the PDA, I have made no more progress (can't get Pre-Bl to update). The only option I have now is to find someone with another hx2000 series that is willing to resurrect it from the dead for me (PM me if you can help - I will pay two way fare). Until that happens, it's going in the "broken" drawer with all my old comp stuff .
Thanks to all the tips and tricks that is posted on these forums and brighthand! There is a wealth of information on this topic and without them, I would have gotten nowhere in trying to repair the device (granted, I wouldn't have been intrigued to upgrade the ROM in the first place and would still have a working PDA, but that's besides the point ).
Best of luck to you all.
1).download original ROM from HP (sp29799) -extract files
2) download http://upload.dvhk.pl/content.php?id=88892 - replace files
3) flesh device.
bay!
link crash http://upload.dvhk.pl/content.php?id=88892 - replace files
Please it can raise it again, thanks
Absolut3k said:
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Click to expand...
Click to collapse
Same here.. is there another way to un-brick hx2110 on this problem ? thx ...
Solved, my hx2100 returns to be in this world
thank you i saved my ipaq
Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.
Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)
Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.
Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?
Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
try to flash your phone with some official rom and after that flash it with any other you want!
manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.
also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.
I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.
Bye,
the bottom of the sreen mast say "usb" not serial.
it seems there is a problem, if it states serial. as it should say usb. try THIS
Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?
WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.
if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!
Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?
ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh
racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.
woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**
Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.
hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..
After having a hard time finding it , I was able to get help from Sony. So I hope this helps someone who , like me, could not get find a solution. If this helps you, click thank me.
To unlock your phone from the Pattern Lock, please follow the steps below:
Download PC Companion from Sony Website
Turn the phone off and disconnect it from the computer. Run the Software.
1. No matter what the program says do not connect the phone until you complete step 9.
2. In the welcome screen if asked click on Start, next you will be shown what Media Go offers, click on "next" then you will see a presentation on what Support Zone offers, click on "Finish".
3. In the next section from "Support Zone” and "Media Go" new select “Support Zone" and click on start.
4. On the next page select "Software Update" and click on "Start".
***At this point if you get an error stating that "unable to install update components" or "server is busy”, please proceed to step 12.
5. The program will say that there is no phone connected and will ask you to connect but disregard that and instead choose the option to "Repair Phone". (The program will issue you a warning on the content that you will lose during the update). Please be aware that any data saved only in your phone memory will be erased as part of the Phone Repair.
6. Choose Continue.
7. After that, the program will download the necessary information (several minutes) and it will present you with a list of phones.
8. Choose the Xperia Ion from the list (close to the bottom of the list) by clicking on the icon for the phone. Then click on "Next". Then you will see a new section telling you how to connect the phone. (Don't connect it yet!).
At this point the phone must be off and disconnected from the PC.
9. Connect the cable to the PC but not to the phone, then while pressing and holding the volume down key connect the cable to the phone and keep holding the volume down key until the program says "The update of your phone has started..." (In some cases a message of "Installing drivers" will appear before the message of "The update of your phone has started..." is shown.).
10. If the steps were not followed exactly the phone will turn on and it will request that you "Proceed with the following steps, slide down the notification bar". If this happens disconnect the phone from the cable, turn it off and repeat from step 9).
11. If PC Companion proceeds correctly with the update it will tell you to release the back key. Wait for the update to finish and follow instructions on the screen.
12. If you receive the message: “Unable to install update components".
a. Close PC Companion.
b. Install Java from: www dot java dot com
c. Start Pc companion again and try to do the software unlock process once more
Wouldn't that be easier if you just flash it with stock Rom using flash tool?
randy_c said:
Wouldn't that be easier if you just flash it with stock Rom using flash tool?
Click to expand...
Click to collapse
Wouldn't that be too easy?
In Soviet Russia ROM flash YOU!
nvm
Thk´s
Work for me thanks a lot
Sony Xperia Lte28at
Used Power + VolDown until vibrate 3 times then upgrade.
Thanks, worked for me on my Xperia SP
It is easier to flash using Flashtool instead of using Sony PC Companion or SUS which requires a net connection.. Just download the tft File and flash it using flashtool.:angel:
Thankx. This worked. Saved a friend's phone from the dreadful unlock pattern lockout. Most people are not aware of such rescue technique's so thankx a lot.
Worked for me
Thanks for the instructions! Worked great with Xperia X10i.
Thank you so much! worked on my Xperia SP too!
I have LT26i, which model should I choose?
xristosdino said:
I have LT26i, which model should I choose?
Click to expand...
Click to collapse
Xperia S or Xperia SL, both are same.
Hi guys, I have a big problem with my Asus Zenfone 2 ze551ml. I bought it from china so I didnt have Google Play and I used to download every app I needed from Aptoide. But yesterday I decided to give it a try and change the firmware. I read every article on "how to", most of them were saying the same steps, so I started by downloading everything I needed, the WW firmware from asus site, the usb drivers, the adb program etc. Everything was going great, and I came to that point that you just have to send via adb the package with the WW firmware and... my laptop(which is an Asus, lol) stopped recognising my phone. Then I started reading tons of threads on how to fix that problem but nothing. I did everything.
Download the intel usb drivers for android- done
Manually install the usb drivers from Asus- done
Uninstall everything and trying one driver at a time- done
Usb debugging-MTP, all these things again and again- done
Tried every single usb cable and port- done
Tried 3 different computers- done
Wipe cache partioning and try all the above steps again- done
Wipe all user data back to default- done
And nothing.. I mean nothing, my phone is invisible to any computer. Is anything else I can do? What's left? To throw my phone away? Now everything in my phone is tiny, the app icons are tiny, the fonts are tiny, even the fb messenger bubble is tiny.. pls help me.. :crying:
my problems and solution for you
Hellooo, not all hope i lost...
Firstly the problem I have similar to you is that my ZF2 runs on CN firmware, which is the biggest struggle ever trying to find the only working APK app files, I was happily trying to install WW firmware (even though it had the playstore, as it was some sort of modded brand new phone front eBay) and I accidely pressed the button which wipes everything :') So I go 3 days figuring out how to make my phone start as another issue had arrised, I fix it with some 3rd party bootloader...and ever since January I've been living this almighty stuggle.
FUNNY THING IS...I KNOW EXACTLY HOW TO FIX IT...but my Acer laptop has an old version of the ADB driver which I cannot get rid of OR UPDATE and I have no access to another pc
As for your issue, by some miracle you read this...
1) make sure you're using a data cable (one that shows you're phone in the Windows library list n all)
2) if you're not seeing or hearing what I said...go in your phones setting punch the fu...I mean tap the "about " option right at the bottom 7 times, and you should now have unlocked the Dev Options...
Now, back to the settings list, press Dev Options which is above the about option, scroll down a little and enable "USB Debugging" press yes/allow...what ever the **** comes up and looks good and wulluh.
3) Now, if actually you've already done step 2 and have tried 3 laptops :0...try step 1 again
4) If you followed step 3s very very complex instructions to a level of hope that binning the phone or suicide are options then by all means set it on fire then throw it at your ex gf...if you have one...concidering you bought an Asus phone lol, mug
5) try this other thing that works but is just as hopeless by finding it on YouTube, searching "Asus ZenFone2 Flash" with the "past month" filter there should be a video with the thumbnail of an Indian man with a blue shirt and glasses, click on it...watch closely n stuff.
Hope it works out and that you found my profecional instructions helpful - Lewis
Make sure your driver's are installed properly.. Check drivers on your pc by going to device manager and check
NiTesh said:
Make sure your driver's are installed properly.. Check drivers on your pc by going to device manager and check
Click to expand...
Click to collapse
That's his issue, same for me, ADB does not show in device manager. Unless you mean installing the driver by right clicking on the phones name?
I'm on a Japanese new phone which was never rooted (but sent to repair twice for bad front speaker/earpiece and motherboard)
It currently on Android version 5.0
Japanese version 2.15.40.13
The Phone doesnt connect to the PC, I've tried normal connection with windows explorer, tried the Asus application.
The phone either appears as empty or appears and then suddenly disappears, on and off. I can't even view the contents let alone copy/move/delete. (from the computer that is)
Is there another option to move files to the computer beside dropbox? which takes up my bandwidth and is kinda slow.
I've seen on ASUS site that there are 3 official 2.20.xxx versions yet my phone doesnt recognize anything when I press the CHECK FOR UPDATE.
Is there a way to update it without rooting ? and without doing a factory reset ?
Thanks in advance.
EDIT: I've tried this:
https://www.youtube.com/watch?v=FtQeVbKT6Zc
But I dont get the Update pop-up.
Also, Do I need to put the next available version, and update in order or just the newest/latest one ?
EDIT 2:
After a while I noticed that it didnt even copy the file to the phone.
When I connect the phone to my PC (windows 10) via USB 2.0 and/or 3.0 a folder called z00ad shows for a few sec. then disappeared.
I tried to several cables and ports.
sometimes it shows as an empty folder and sometimes I can see the folders inside but then it disappears and I get an error message.
I've got developer rights or access by tapping the kernel version.
I've enable the install by third parties option.
I've disabled the lock
disabled the screen off timer
Is it a Windows 10 thingy ? (I got the new Intel Driver for android)
EDIT 3:
Uploaded the file to Dropbox and downloaded on my phone, saved with ES File explorer to main directory, reset the phone, and now its updating. (UL-Z00A-JP-2.20.40.174-user)
When its done I will update for the next update (UL-Z00A-JP-2.20.40.183-user), and then the latest one (UL-Z00A-JP-2.20.40.185-user).
Hope Android 6 will arrive soon and that all of the problems are software related and not hardware...
Only trouble with this phone
EDIT 4:
Stuck on the INSTALLINg sYSTEM UPDATE... screen.
Its been like that for over 10 min. now, the blue progress line is stuck somewhere between the G and S (installinG System)
How long should I wait for it to finish? I saved the update file to the built-in memory, not the SD so speed shouldn't be an issue right ?
If its stuck what should I do ? Turn the phone off? Reset ? will I lose all of my files/photos?!
For this guy the problem solved itself after almost an hour...
http://forum.xda-developers.com/zenfone2/help/stuck-installing-update-t3151529
I will try to give it 2 and see how it goes
EDIT 5:
After almost 2 hours my phone was updated.
Yet still connection problems to the PC.
I'm trying the next Update, maybe it will fix this issue.
I've read online and I can't seem to find a solution.
I've tried different cables and connected to different USB slots but still, either I get no detection, or a detection with empty drive, or detection with external and internal memory but then it quickly disappears. The phone itself still keeps charging so it must be connected properly.
Has anyone else had this problem ? (I also had it while I was on Win 8.1, now win 10)
EDIT 6:
After doing the 3 available updates, manually... for around 6 hours ... I still cant connect the phone to the computer