[Q] please help a noob, problem note 2! - Galaxy Note II Q&A, Help & Troubleshooting

Hi everyone,
I'm writing you hopping for a clue and some good pointed advices.
My story:
note 2 N7100 rooted started to block. I manage to backup more than 3k sms and around 8 gb of data.
and it works just fine, but I still had a itchy to change the ROM.
I started to read, it was my first time flashing an android, in the past I used to flash with success many time my wm6.5 HTC.
Ok, i'm ready.
i founded some beautiful roms and I was excited to see them on my note.
what did I done?
first I've copy the new rom on sd card.
I follow all the steps for CWM.
the problem was that I followed all the steps till instal. I didn't seen On my sd card the rom that i've copied.
I was not 5 minutes cleaver to pull out the sd card, but I've stopped the phone.
Yes, everything was erased.
The only thing I could get was the starting logo with note 2 ( white letter on black background) nothing more.
I've tried with odin1.85, odin3. every time same result...fail.
I can go in Odin Mode and I can get this message :firmware upgrade encountered an issue.Please select recovery mode in Kies& try again.
I've tried in Kies but no luck
As far as I can understand my phone is empty..
Question is what should I do?
Please don't tell me I can throw it away!!!
PLEASE HELP!
Please if you will respond on this thread make it like for a noob!
Thank you in advance

what Rom u was installing ?
i think u should use Odin 3.07
http://samsung-updates.com/Odin307.zip
find latest stock Rom for ur N2 ( N7100 or N7105 ) here : http://www.sammobile.com/firmwares/1/
download it and unzip it then open odin and put it in PDA and wait a bit it will check MD5 then it will work then put ur note in download mode ( home + vol down + power ) and connect ur note2 ( odin should give u blue color on ID com )
and make sure Kies is totally closed then hit start and wait
like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
if the device stuck at boot screen just go the recovery and do full wipe ( it will wipe ur internal memory too )
good luck :angel:

yahyoh said:
what Rom u was installing ?
i think u should use Odin 3.07
find latest stock Rom for ur N2 ( N7100 or N7105 ) here :
download it and unzip it then open odin and put it in PDA and wait a bit it will check MD5 then it will work then put ur note in download mode ( home + vol down + power ) and connect ur note2 ( odin should give u blue color on ID com )
and make sure Kies is totally closed then hit start and wait
like this
[IM/59541221/oG]
if the device stuck at boot screen just go the recovery and do full wipe ( it will wipe ur internal memory too )
good luck :angel:
Click to expand...
Click to collapse
thank you for your feedback.
I've downloaded the latest version for N7100 from the site you mentioned.
the truth is I've used Odin 3.04 and have no luck.
I've followed every step you mentioned.
I'll try with Odin 3.07.
I can't go to recovery I don't have this option or I don't know how to access it.
When I press those 3 buttons the phone goes into download mode.
How can I access recovery?
Thank you Yahyoh

to go to recovery use home + vol up + power

yahyoh said:
to go to recovery use home + vol up + power
Click to expand...
Click to collapse
I've done that and I get the death message ( i've read about this death message, I want to hope that is just an over reacting saying)
"firmware upgrade encountered an issue.Please select recovery mode in Kies& try again"
in my opinion, if I'm allowed to have one, I think I deleted everything on my phone. even the bootloader and so on.
Is just empty
which are the steps to follow in order to have a working phone?
thanks Yahyoh for your attitude and patience.

Remove battery for 5min
Press Vol down +home+power
It should reboot to download mode
Instead of download mode still you getting msg 'encountered error...' consider that screen as download mode and flash rom with odin.
Version of odin doesn't matter.
Sent from my GT-N7100 using xda premium

Related

Instaled wrong ROM, how reinstal? P6-C00

I have Huawei P6-C00. It is Dualsim, china version. I tried instal CyanogenMod 10.1 for p6-u0. Now I can start my phone. When it starts I see:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I tried instal it by Recovery but I have only this options:
When I conected my phone to computer by USB:
I have clear ROM for my version but I can't instal it. How I can do this? Please help me.
aknorts said:
I have Huawei P6-C00. It is Dualsim, china version. I tried instal CyanogenMod 10.1 for p6-u0. Now I can start my phone. When it starts I see:
I tried instal it by Recovery but I have only this options:
When I conected my phone to computer by USB:
I have clear ROM for my version but I can't instal it. How I can do this? Please help me.
Click to expand...
Click to collapse
dissconnet it from the usb port and if you have the update.app in the dload folder in your SD card, the update should work
It is Dualsim model, It has not SDcard. In place SD slot is second simcard.
Any other solution this issue?
From here
http://dl-uk.huaweinews.com/index.php?dir=Roms/Ascend-P6/
I have oryginalny ROM for this phone, but I don't idea how I can instal it.
Do You have access to external memory via USB?
So, can You use it as mass storage?
If yes, then create a folder on the internal storage vith the name DLOAD and put the official ROM (the file called UPDATE.APP) in it.
Power off your P6.
Hold both vol up and vol down. Turn it on and hold all the three keys (power on, vol up, vol down). When You see Huawei logo, release the Power key, but still hold the vol buttons, untill You see that the update starts.
This is how I could go back to stock ROM from MIUI..
1. No I has not access to external memory via USB. When I tried connect it. I have communicat: http://oi42.tinypic.com/102kz04.jpg
2. No I cant use it as mass storage.
3. When I hold all three keys I see: http://oi44.tinypic.com/jv0xug.jpg
If you can't help I will go to servis with Jtag, but how they open this phone? They can open phone?
aknorts said:
1. No I has not access to external memory via USB. When I tried connect it. I have communicat: http://oi42.tinypic.com/102kz04.jpg
2. No I cant use it as mass storage.
3. When I hold all three keys I see: http://oi44.tinypic.com/jv0xug.jpg
If you can't help I will go to servis with Jtag, but how they open this phone? They can open phone?
Click to expand...
Click to collapse
ur problem isn't that big, u just need to put the firmware file on your internal storage, u might try to flash TWRP via fastboot and u can access your internal storage from it with usb
7OOKA said:
ur problem isn't that big, u just need to put the firmware file on your internal storage, u might try to flash TWRP via fastboot and u can access your internal storage from it with usb
Click to expand...
Click to collapse
adb does not work in stock recovery I think...
edit: oops, my bad. He should be able to do it in the download mode
Thanks for answers.
I am noob, how do it?
aknorts said:
Thanks for answers.
I am noob, how do it?
Click to expand...
Click to collapse
first follow this amazing guide : http://techglen.com/2013/10/01/abd-and-fastboot-guide/
then continue with TWRP guide
Hey, thanks for your help. I do exacly what is in turtorial. But where can I take the recovery_original_flashable.img? It is in ROM? Where?
aknorts said:
Hey, thanks for your help. I do exacly what is in turtorial. But where can I take the recovery_original_flashable.img? It is in ROM? Where?
Click to expand...
Click to collapse
that if you will flash stock recovery, but i guess u will flash TWRP, so after finishing the 1st guide go straight to TWRP thread and download it from there
Good luck
Ok, thx. I did this. But all time I has comunicat: "wait for device" and nothing happend.
aknorts said:
Ok, thx. I did this. But all time I has comunicat: "wait for device" and nothing happend.
Click to expand...
Click to collapse
i will assume that u followed the fastboot guide to the letter and everything went fine, open driver tools and uninstall the drivers and reinstall it, then connect the device to the pc and hold power and vol - buttons till the device reboots then release the power button and keep holding vol - for few seconds (2 or 3) then your pc should recognize ur device as an "adb interface" then u can flash the recovery straight (fastboot flash recovery recovery.img)
if that won't work then u did something wrong in setting fastboot
I tried in two PC and I did step by step. Really I don't know what is wrong.
Probably will not work, but try this one: http://forum.xda-developers.com/showthread.php?t=2618253

[How To] Installing ClockworkMod Recovery On Samsung WIND T999V! EASY!!!

Ok guys, after about 3 days of search i finally find how to install Clockworkmod Recovery (Touch Version) on my WIND T999V so im sharing it with you!
Assuming you are already rooted right? Ok then read on!
If not then i suggest you follow mrRobinson's thread on how to root.
Note: THIS METHOD WILL TRIP YOUR COUNTER!!!
So if you worrying about that then please read how to remove that using Triangle Away here
I would like to quickly say im not responsible if you brick your device! so please take the necessary precautions etc​
Ok lets move on.
Files needed:
FIRST Make Sure that the Samsung USB drivers are installed. You can find it here
Odin: Located here
CWM Recovery: Located here (Although this is for T999V other phones are listed but im not sure if the procedures are the same)
MD5 Checker: Located here (This is to check your download files to see if they are complete or correct files)
Download Odin.
Turn off your Phone and Turn it On While Pressing, Volume Down + Home + Power button until you see the download mode screen, Press Volume Up to continue.
Open Odin in Computer and connect your device to PC, while it is in the Download mode.
If your Phone is successfully connected to PC, the Odin port will turn Yellow with COM port number and in the status section you see <Added!>.
Now Click on PDA and select the File "recovery-cwmtouch-6.0.4.3-d2tmo.tar" (would be better to rename it something like recovery.tar).
In Odin, Check Auto reboot and F.Reset Options if they are not already checked.
Now Click the start button and wait for the process to complete.
After the installation is complete you device will restart and once you see the Home Screen, unplug the cable.
You should now have CWM Recovery installed!
To check turn your phone off and press Volume Down + Home + Power.
OPTION 2
Ok so after a few more brain storming, trials and error i found out that i can actually install CWM from ROM Manager without going through the above process. Anyways i am leaving it just in case some users need it.
Now its simple to get CWM for your phone!
First Download ROM Manager (if you are rooted)
Open the app
Select Recovery Setup
Select INSTALL OR UPDATE RECOVERY
Select the Option Button >>>>>
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Select Show All Devices
Select Ok at the popup
Scroll Down untill you see Samsung Galaxy S3 (T-Mobile) (it should have d2tmo below it)
Select It
Select Flash ClockworkMod Recovery
Wait until its finish and you are good to go
Note: If you want to support the dev you can Select YES at the Flash ClockworkMod Touch before you Select Flash ClockworkMod Recovery its just $1.99!
Its easier to use anyways!
2nd method with ROM MANAGER worked well on my wind s3.
Thanks for sharing
Root is not required for the first step. Both methods will work for all T999 variants in case anyone is wondering. Good write up

please help my phone stuck on samsung logo

hello guys
my phone can't boot when i turn on my phone stuck on samsung logo
please i need help i download the official firmware and i try to install this firmware "N7100XXUFND4_N7100OJVFND3_N7100XXUFND3_HOME.tar.md5" by odin but nothing happen
and i can't access recovery mode
can any one help me please
suirs said:
hello guys
my phone can't boot when i turn on my phone stuck on samsung logo
please i need help i download the official firmware and i try to install this firmware "N7100XXUFND4_N7100OJVFND3_N7100XXUFND3_HOME.tar.md5" by odin but nothing happen
and i can't access recovery mode
can any one help me please
Click to expand...
Click to collapse
Boot your phone to download mode by pressing vol down+home+power buttons together. Then plug in the usb cable, run odin and select the md5 file. Click on start. Be patient it should automatically reboot within a few minutes. If it doesn't try flashing a custom recovery like TWRP through odin and do a full wipe before flasing. Hope it helps!!
joy854 said:
Boot your phone to download mode by pressing vol down+home+power buttons together. Then plug in the usb cable, run odin and select the md5 file. Click on start. Be patient it should automatically reboot within a few minutes. If it doesn't try flashing a custom recovery like TWRP through odin and do a full wipe before flasing. Hope it helps!!
Click to expand...
Click to collapse
i trying to install custom recovery TWRP by odin but when i finished nothing happen
and i try to install custom recovery PhilZ Touch but when i finished nothing happen
i wanna some help pleaseeeeee
suirs said:
i trying to install custom recovery TWRP by odin but when i finished nothing happen
and i try to install custom recovery PhilZ Touch but when i finished nothing happen
i wanna some help pleaseeeeee
Click to expand...
Click to collapse
What error do you get in odin when flashing stock firmware?Is your phone being detected by odin in the first place?Is the ID:COM port lighting up blue which means successful connection has been established between phone and odin.If ID:COM doesn't light up then you need to change your USB CABLE (if you are not using stock samsung cable ,if you are then use another stock samsung usb cable)Screenshot the error if any you get in ODIN and upload it for us.
singhpratik87 said:
What error do you get in odin when flashing stock firmware?Is your phone being detected by odin in the first place?Is the ID:COM port lighting up blue which means successful connection has been established between phone and odin.If ID:COM doesn't light up then you need to change your USB CABLE (if you are not using stock samsung cable ,if you are then use another stock samsung usb cable)Screenshot the error if any you get in ODIN and upload it for us.
Click to expand...
Click to collapse
firstly i use the stock samsung cable
and when i connect my phone in odin i got lighting up blue in port ID:COM
and i got this problem when i press start
this before press start
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and i got this problem after press start
please i need some help
when i install TWRP custom recovery i got in ID:COM port this
but when i try to enter to recovery mode i can't
please i need help
now i download the N7100XXUFNE1_N7100VFGFNE2_N7100BUUFND2_HOME.tar firmware
but when i try to install via odin i got Fail
i need some one help me to found solution for this problem
i need some help from anyone pleaseeeee
suirs said:
when i install TWRP custom recovery i got in ID:COM port this
but when i try to enter to recovery mode i can't
please i need help
Click to expand...
Click to collapse
What happens when you press VolUp+Home+Powerbutton?
Release buttons as soon as Samsung font appears. and then?
Androidwizzard said:
What happens when you press VolUp+Home+Powerbutton?
Release buttons as soon as Samsung font appears. and then?
Click to expand...
Click to collapse
nothing happen
just i see samsung galaxy note 3 gt-n7100 and the phone restart and stuck on the samsung logo
can anyone help me pleaseee and tell me what can i do ??
i try this firmware N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar
and when odin finish give me "Pass"
and when my mobile restart still stuck on samsung logo and still can't access recovery mode
Definatly seems like there was an issue with Odin, but you need to get it into download mode to return to stock then try again.
Had the same ****; Please check if your internal storage is available. Mine has the exact same problem and it could be due to faulty hardware (emmc).
To check if the internal storage is mounted check your recovery. it will indicate that it couldn't mount system and a range of other mounting errors. You could use adb to see which volumes are mounted.
(Check my thread http://forum.xda-developers.com/showthread.php?t=2716444 it has detailed info about how to check your volumes)
Gamebytes said:
Had the same ****; Please check if your internal storage is available. Mine has the exact same problem and it could be due to faulty hardware (emmc).
To check if the internal storage is mounted check your recovery. it will indicate that it couldn't mount system and a range of other mounting errors. You could use adb to see which volumes are mounted.
(Check my thread http://forum.xda-developers.com/showthread.php?t=2716444 it has detailed info about how to check your volumes)
Click to expand...
Click to collapse
hey bro can you tell me how to check internal storage
and if i wanna to use any program can you give me this program
can anyone please give me That's factory firmware
N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar
i mean i need stock firmware with repartition capability because this only firmware work on my mobile but i need the best pit file to see whats happened
i need the pit file compatible with this firmware
N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar
can any one give me the pit file pleaseeee
i download this pit file
PIT_N7100_16GB_20121102.pit
and when i use this i get fail
but if i remove pit file i got pass in ID:COM

[HOW TO] Fix ODIN fail while updating to 6.0.1 MM

I had a hard time updating my 928F to 6.0.1 via odin,
everytime i start flashig i get fail message from odin and my phone get stuck on dowloading screen,
But after a few tries, watching couple of "how to videos" and a little bit of luck i managed to pull it out.
So lets get started:-​
Prerequisites:
1. Stock 6.0.1 firmware from http://www.sammobile.com/firmwares/
2. 7zip from http://www.7-zip.org/download.html
3. Last version of ODIN from http://forum.xda-developers.com/showthread.php?t=2711451
4. TWRP (I mean compatible)
1. First, for best result you need to do a clean flash by doing advanced wipe from TWRP (Dalvik / ART Cache - Cache - Data - Internal storage - System).
2. Unzip the firmware you dowloaded and you should get xxxxxxxx.Tar.md5
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Rename to xxxxxxxx.tar
4. Unzip it again and you should get that:
5. Rename "Hidden.img" to "Hidden.img.tar
6. Make a new folder and move what you get from last unzip EXCEPT "Hidden.img.tar".
7. Using 7zip,
8. After 7zip finish up, load the new compressed file in ODIN "AP" or "PDA" section.
9. Boot your phone into Dowloading mode and connect it to your PC.
10. Press start on ODIN.
11. Now after ODIN finish flashing and before your phone is rebooting, Enter Dowloading mode again and flash "Hidden.img.tar"
12. Now your phone should start up and install new update in stock recovery.
13. If you got stuck in bootloop, boot in stock recovery an perform a factory reset and wipe cache.
CONGRATULATIONS ​
--Sorry for my bad english--
IF this helped you by anyway please press thanks.
Thanks a lot
Can I use your steps
If my phone blocked to one operateur??
Sent from my SM-G928F using Tapatalk
andrew_121212 said:
I had a hard time updating my 928F to 6.0.1 via odin,
everytime i start flashig i get fail message from odin and my phone get stuck on dowloading screen,
But after a few tries, watching couple of "how to videos" and a little bit of luck i managed to pull it out.
So lets get started:-​
Prerequisites:
1. Stock 6.0.1 firmware from http://www.sammobile.com/firmwares/
2. 7zip from http://www.7-zip.org/download.html
3. Last version of ODIN from http://forum.xda-developers.com/showthread.php?t=2711451
4. TWRP (I mean compatible)
1. First, for best result you need to do a clean flash by doing advanced wipe from TWRP (Dalvik / ART Cache - Cache - Data - Internal storage - System).
2. Unzip the firmware you dowloaded and you should get xxxxxxxx.Tar.md5
3. Rename to xxxxxxxx.tar
4. Unzip it again and you should get that:
5. Rename "Hidden.img" to "Hidden.img.tar
6. Make a new folder and move what you get from last unzip EXCEPT "Hidden.img.tar".
7. Using 7zip,
8. After 7zip finish up, load the new compressed file in ODIN "AP" or "PDA" section.
9. Boot your phone into Dowloading mode and connect it to your PC.
10. Press start on ODIN.
11. Now after ODIN finish flashing and before your phone is rebooting, Enter Dowloading mode again and flash "Hidden.img.tar"
12. Now your phone should start up and install new update in stock recovery.
13. If you got stuck in bootloop, boot in stock recovery an perform a factory reset and wipe cache.
CONGRATULATIONS ​
--Sorry for my bad english--
IF this helped you by anyway please press thanks.
Click to expand...
Click to collapse
sorry sir ,when i created tar , just like you tell ,
tar no work .
odin do nothing
can you help me ?
yaniyu said:
sorry sir ,when i created tar , just like you tell ,
tar no work .
odin do nothing
can you help me ?
Click to expand...
Click to collapse
can you take a screen shot of odin log?
DR_ASHK said:
Thanks a lot
Can I use your steps
If my phone blocked to one operateur??
Sent from my SM-G928F using Tapatalk
Click to expand...
Click to collapse
I'm not sure!
andrew_121212 said:
can you take a screen shot of odin log?
Click to expand...
Click to collapse
can you show how to upload screen shot? sir
Hi...will this work for galaxy c7? I got exactly same problem

Partly bricked... SM-N975F

Hey guys.. Ive been a visitor in XDA forums for quite a while... And i been running root and custom FW with more or less every samsung from S2 and up...
But i just got my self a note10+ (atleast thats what ive been told) and i wanted to root it up and throw a custom FW on it to run in Samsung Dex...
So i succeded updating the FW. I unlocked the bootloader in dev. options. and unlocked it again in download mode by holding the vol. up. key!
But since then i had problems... every time i run a FW in Odin... Then if i dont get a error saying
SW REV. CHECK FAIL(BOOTLOADER) DEVICE: B BINARY 7
pit_flash_binary - Unsupported version
Then i succeds but when its going to erase everything after the reboot from download mode then it starts up and stops right after... And then i can only go recovery mode and download mode... How do i just write the correct firmware and have it start up like normal... just wanna undo it all... Do i need some kind of samsung support software in windows? and how do i know if it is a note10+ ... Even though download mode says SM-N975F... But still i get error when i flash a FW downloaded with Frija for that model...
Hope to get some help
oh btw... it connects as this when im in download mode:
"Checking Connected Devices: SAMSUNG Mobile USB Modem #2 ( COM12 )"
is that normal?
bump?
Hey there,
SW REV. CHECK FAIL(BOOTLOADER) DEVICE: 8 BINARY 7
Click to expand...
Click to collapse
This, as far as I understand just means that the bootloader on your phone is on a newer version than the one in the firmware you're trying to flash. Usually flashing just stops there.
Then i succeds but when its going to erase everything after the reboot from download mode then it starts up and stops right after...
Click to expand...
Click to collapse
You COULD try to simply boot into recovery and wipe the device once, the phone would usually do that on its own but sometimes fails. Mind describing what exactly happens?
how do i know if it is a note10+ ... Even though download mode says SM-N975F...
Click to expand...
Click to collapse
For that, you either need the original packaging or just trust on what Odin-mode is telling you.
But still i get error when i flash a FW downloaded with Frija for that model...
Click to expand...
Click to collapse
I kinda don't trust Frija. For me, Bifrost always worked like a charm. Use it to download the firmware for your SM-N975F and give it your correct region code.
For flashing, some people use Heimdall, I think Odin is pretty simple (as far as simplicity in modding goes).
By the way, if all fails, you could try installing LineageOS 19.1, throw in openGAPPS for Googles apps and Magisk/Lygisk for root (if needed).
Good luck and have fun!
Cheers!
I found out i got EXACKLY the same issue as the guy writing on this thread:
Need help with semi-bricked Note 10 Plus (SM-N975F) - Stuck on recovery/download mode
Didn't know where to post this exactly, to be honest. This will be a long post I was flashing AOSP roms in the phone. Tried to go back to One UI for the VoLTE thing In one of the AOSP roms I couldn't install it in Lineage Recovery (older version...
forum.xda-developers.com
Nic0_ said:
You COULD try to simply boot into recovery and wipe the device once, the phone would usually do that on its own but sometimes fails. Mind describing what exactly happens?
Click to expand...
Click to collapse
Already tryed still nothing... But what happens after a 100% succes in Odin is:
Then it reboots and after a few secs it says "Erasing device" for like 0.5 sec... And then it only goes black screen... At black screen then i can only go download mode if i press both volume buttons at the same time for 1 sec. Or recovery mode if i press vol up and power. And thats only if i have a USB-C connected ofcourse.
And whats the issue is... when it stops erasing the device... Why does it stops after 0.5 secs? it normally goes like 2-5 secs ... But also ... After it stops and in black screen... If i continue into download mode and open up the bootloader then...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I been around TWRP, Original recovery and Lineage recovery... But as the guy writes on the other thread. Then it shows 0 MB on the data partition, and i have to format it before it shows up again with 223 (or something)GB again...
Hey there,
Could you try switching file systems around? TWRP lets you format your partitions with stuff like ext4, f2fs and some other file systems. On several custom ROMs, the file system sometimes is the difference between a system working or bootlooping.
Good luck and have a nice day.
Cheers!
Already tryed exfat and f2fs and then back to ext4
I might have found a solution
I tried to update firmware N9750 android 11 to android 12 with (Ap file + odin patched). I don't flash bl ,cp,csc files . the phone screen shows a software error, need to open the smart switch software on the computer to recover. I open the smart switch on the computer and it does not recognize the phone. odin patched still recognizes the phone is connected. i reset odin and flashed 1 BL file. phone booted again with bootloader + AP file is android12. and modem and csc are android 11
1: Try flash combination firmware?
2 : Try download firmware stock new bootloader
Download odin patched
Try flash firmware files one by one
restart phone go download mode flash file BL ..done
restart phone go download mode flash file AP
restart phone go download mode flash file CP
restart phone go download mode flash file CSC
If ok flash full 5 file
sorry my english is not good
someone could help please?
S20 FE bootloop after security update
So I never posted here but I usually pass by some topics so sorry for any mistake in creating this discussion. Today I deleted some stuff from my S20 FE and downloaded via OTA the march security update in my device, then I was caught by surprise...
forum.xda-developers.com

Categories

Resources