So I try to root (Following the instructions) and this happens
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
What do I need to do? Flash the stock firmware? Do a Kies Emergency whatever?
Reboot your computer, use usb ports on the back (#1 on a laptop), use a known good cable. Reflash a stock Rom, then try the auto root again. Or, flash the no trip root in mrRobinsons thread. Both will root. And I would recommend Odin version 3.07. Several people have reported success using the older 1.8x versions, but I like the newer one for the newer phones.
this worked for me
Are you running Windows on a Mac using vmfusion? That could be the problem, try Odin with a windows computer, it worked for me
Related
So I've been screwing around now for somewhere around 7 hours trying to figure out how to root the s4. I've tried both the motochopper and odin methods on pc and mac and every time i end up with the same errors. I've followed the instructions word for word and tried again with after wiping the phone of all its data. heres the log for odin:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
Then motochopper seems to run smooth, but then says:
Rooting phone...
This may take a few minutes.
Failure.
Cleaning up...
Exploit complete. Press enter to reboot and exit.
Press any key to continue...
Any ideas? I have the SGH-M919 T-Mobile version.
did you do the ota update before you tried to root? I did, and had to oden back to the stock m919uvuamdb version, then motochop, then flash a recovery of your choice, then you can flash any of the roms, custom or stock+root. thru recovery. I think maybe now there is an updated stock with root avail,
and make sure you follow directions for unzipping and placing the .tar in the right place (pda) and uncheck all but reboot
If you've updated then you are UVUAMDL, follow this
http://forum.xda-developers.com/showthread.php?t=2268880
Also, there is a a problem flashing CWM or TWRP. Just be sure to read the first 4 pages of that thread
Alternate method which I did on MDL:
1) Odin OUDHS Recovery, download SuperSU cwm zip from link in thread: http://forum.xda-developers.com/showthread.php?t=2260031
2) Then cwm rebuilt kernel with root restriction removed: http://forum.xda-developers.com/showthread.php?t=2271976
3) In the same session cwm the SuperSU zip mentioned in #1.
Can you log into a root shell?
Sent from Spaceball One.
Solution
You need to flash t Mobil kernel to get root and root thrue cwm method
hi im trying to return to stock from kk and when i use odin this happens:
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
does anyone know what to do, i've never ran into this before... i've tried odin versions 1.85 and 3.07
info, phone was running vanir 4.4.2 nightly tried to update to latest and phone wouldnt start os so booted into recovery and it went straight to trying to install the rom again, and keeps doing so, so im trying to return to stock to start a new. yes the flash was a dirty flash (vanir has an ota updater script that lets you know a new version is avalible and after downloading it will ask if you want to install, from there it reboots into recovery and installs it and reboots all for you, and it seems like it just got stuck...)
deathblade said:
hi im trying to return to stock from kk and when i use odin this happens:
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
does anyone know what to do, i've never ran into this before... i've tried odin versions 1.85 and 3.07
info, phone was running vanir 4.4.2 nightly tried to update to latest and phone wouldnt start os so booted into recovery and it went straight to trying to install the rom again, and keeps doing so, so im trying to return to stock to start a new. yes the flash was a dirty flash (vanir has an ota updater script that lets you know a new version is avalible and after downloading it will ask if you want to install, from there it reboots into recovery and installs it and reboots all for you, and it seems like it just got stuck...)
Click to expand...
Click to collapse
ok fixed it, needed to download older version of cwm and flash it via odin then wipe everything then flash latest twrp vid odin and that fixed it
older CWM + ODIN (and everything else to root stock 4.1.1) (please note i did not compile this just posting the one i found to fix my issue)
Latest TWRP FOR ODIN
please note these file should only be used on D2ATT (Samsung Galaxy S III SGH-I747 AT&T Variant)
I was on resurrection remix rom and I wanted to go back to the stock rom.So I downloaded the firmware for my region from stockroms.net and tried flashing it in ODIN.The problem is that odin gives a fail error when it reaches the end of the system.img file.I don't know what to do here,please help.Here is the progress report from odin.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Try using an older version of odin like 1.85 and also make sure the downloaded rom is ok.
I did that.I used like 3 different versions of odin and 2 stock roms with different regions.No effect.I have flashed TWRP back again so atleast some functionality is restored
Ok seems lik a partition issue. Try using an appropriate pit file.
gambitflash said:
I was on resurrection remix rom and I wanted to go back to the stock rom.So I downloaded the firmware for my region from stockroms.net and tried flashing it in ODIN.The problem is that odin gives a fail error when it reaches the end of the system.img file.I don't know what to do here,please help.Here is the progress report from odin.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
After Flashing The Stock Firmware Through Odin And Recieve Error MEssage Take Of the battery and put it back
Now go to download mode
Connect your phone
open odin
flash cwm or twrp using odin
when flashing is completed your phone is restart at this point Press Vup+Home+Power
Now Recovery is open
dont do anything except restart
it may ask for rooot then install it
now again go to recovery mode and flash custom rom using recovery
hope it works
Hello everybody !
I bought a Note 4 N910A unlocked on amazon but I have now a problem after an failed attempt to go 6.0.1.
My version was the DOI2 (5.1.1.) but I couldn't succed via flashing in recovery mode (update via sd impossible) neither with Odin (stuck at the beginning of the system bar).
I tried several official rom via Odin (N910AUCU2DOI2, N910AUCU1COC4, N910AUCU2COC6...) but same thing : stuck at the beginning of the system bar.
I tried also with a pit file and a nand erase all, but it's not working.
I have no access to recovery, only download mode.
Here is the rapport :
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't know what to do know...
Thanks for you help !
PS : the phone is under warranty but maybe I can find a way before going to the store (in 2 weeks). And I would prefer not use a root way too, unless I have to ^^
Once you were stock to begin with, you should NEVER have to use a PIT file (unless you found some way to change the partition sizes).
Looking at that log, I suspect the issue is with your data cable or PC. I'd recommend trying this on another PC and data cable (just to be sure). It is unlikely that your device is one of those with a defective NAND chip for storage.
Thanks for answer and it worked with an another cable :good:
I'm now in COC6 (5.0.1) and I'm wondering if I can make an update with Odin to go directly in 6.0.1 or I need to make all the others updates?
I have to do all the wipes first?
Thanks for your advices!
I have a Chinese Galaxy Tab pro 8.4 sm-t321, trying to flash TWRP recovery on it using Odin. I have rooted the device using CFAutoroot through Odin.
I downloaded twrp-3.1.1-0-mondrianlte.img.tar and used Odin v3.12.
Odin manages to install correctly (i think?) and it shows "Pass!"
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
But trying to boot into recovery mode fails and it boots into odin mode:
Could not do normal boot.
ODIN MODE
...
UDC START
Could someone tell me what i did wrong? How do it get TWRP to install correctly?
I just want to install google play on it and the guide I read needed TWRP to install Open GApps.
Many thanks
hello
googleplay on googleplay site
regards