Hey, yesterday I managed to make my Arc S unbootable by installing custom roms, flashing boot.img's, etc, and eventually got it to the stage of not turning on atall, and when pressing power button, the LED just flashed green for less than a second.
This guide will take you through reinstalling the Stock OS on your phone, and relocking the bootloader, so your device is just as it was when you bought it.
Please note: I will not take responsibility for any damages this may cause. This worked for me, and should work for you, but I cannot guarantee anything.
So first of all, your bootloader must be unlocked for this tutorial to work, but if you have been flashing custom ROM's, you will have had to unlock it anyway.
The supported devices for this tutorial as below, and also, please note the key you will need to press to enter flash mode:
Xperia arc (LT15i) – back
Xperia arc S (LT18i) – back
Xperia Tablet Z (SGP321) – volume down
Xperia go (ST27i) – back
Xperia neo V (MT11i) – volume down
Xperia ray (ST18i) – volume down
Xperia P (LT22i) – volume down
Xperia ZL (C6503) – volume down
Xperia Z (C6603) – volume down
Xperia PLAY (R800i) – back
Xperia E dual (C1605)– volume down
Xperia E (C1505) – volume down
Xperia T (LT30p) – volume down
Xperia S (LT26i) – volume down
Next, you must download the Sony Flashtool (Emma) from this link, which we will be using to get your firmware back to stock.
So when you have got this downloaded, install it using the .exe file, then goto the folder that it is installed, and paste the 'Customization.ini', that is also in the zip, in there.
The installation folder is usually
“C:\Program Files (x86)\Sony Mobile\Emma\” for 64 bit Windows or
“C:\Program Files\Sony Mobile\Emma\” for 32 bit Windows
Now run the program called Emma, which will be under the 'Sony Mobile' folder in your start menu (Or at the end of your Start screen on Windows 8), you should get an interface like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now, make sure your phone is off, and hold down the button on your phone that is next to your phone name on the list at the top of the post, whilst plugging in the USB cable, and stop pressing it when your phones LED turns green:
If the program shows a message like this:
You cannot continue with this tutorial, as your bootloader is locked.
PLEASE NOTE:
The next step WILL wipe your phone
If your bootloader is unlocked, you should get a list of OS's on the right hand side, select one, and click 'Apply Service'.
Now just leave your phone and computer and go and get a cup of coffee while it completes!
When it is done, you can unplug your phone, then turn it on, and you should have stock Android again!
Next we will relock the Bootloader (Note: This only works on Arc/Arc S, so do not attempt on any other device), so download this file (A repacked version of X10Flasher, with the .ftf file already there), and extract it to your computer (I know its called X10Flasher, but it works fine on Arc/Arc S, like in this video).
(Thanks to Bin4ry for making this tool!)
When you have done this, open the X10FlashTool.exe file, and click Flash in the top left corner, then click 'Ok'.
Now, as we did earlier, turn off your phone, and connect it to your computer whilst holding the Flash key.
Now wait for the program to do its magic, and unplug your phone, and it will be as good as new!
You can now use the Sony Update Service to update your phone to the newest version!
Thank you for reading!
Related
Hello guys so recently I've been wondering why Xperia S mods don't work on our Acro S, some guys said that there's a file inside framework-res.apk that makes it not to work or to be detected by the phone even in your pc when you connect it.
So I tried to look for files inside the .apk, after searching I found out that the file storage_list.xml inside /res/xml folder that contains the following words /mnt/ext_card and I compared it to the file inside the Xperia S mod and it doesn't contain it... so what I did is to replace the storage_list.xml of the Xperia S mod to the stock Acro S storage_list.xml
I flashed the Xperia S mod, fingers crossed, booted up successfully, recieved an sd card error message, I ignored it, I opened up Album app, switch to by folder
view, and... BAM! IT WORKED! IT DETECTED MY EXTERNAL SD CARD! I OPENED CAMERA, FILMS, OTHER APPS AND IT WORKED! I connected it to my pc and it worked! See screenshots below for some proofs
Here's the step by step tut:
REMINDER: MAKE CWM BACKUP FIRST BEFORE DOING SUCH THINGS!
1. Grab an Xperia S theme/mod/ROM
2. Extract framework-res.apk from that mod {can be found at /system/framework}
3. Open the .apk file with WinRAR/WinZip or any extraction tool
4. Go to /res/xml folder and replace the storage_list.xml in that folder with THIS
5. Save changes, replace the framework-res.apk on the Xperia S mod with the ones you modified
6. Copy it to ur internal sd card, FLASH IT, BAM! See how the magic works!
Press the thanks button if it worked for ya! Please test it on Stock based Custom ROMs for Xperia S too. But if you're on unlocked bootloader, flashing an Xperia S kernel will make the external sd card not to work, i don't know, just try if you want...
IT'S NOT MY FAULT IF YOUR DEVICE WILL BE BRICKED
Screenshots (I was using AOSP theme inspired for Xperia S by skifyr123 here):
These were resized to avoid long post
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks, I*ll give it a tray later ... did you try it also with Xperia S roms or just with themes?
ojessie said:
Thanks, I*ll give it a tray later ... did you try it also with Xperia S roms or just with themes?
Click to expand...
Click to collapse
Yes I have tried KA20.1 Xperia SSpeed it worked but I was having some USB connectivity problems so I couldn't connect my USB :/
Good thing I did a CWM backup...
ItBankRock said:
Yes I have tried KA20.1 Xperia SSpeed it worked but I was having some USB connectivity problems so I couldn't connect my USB :/
Good thing I did a CWM backup...
Click to expand...
Click to collapse
Try to use a systemUI made for Acro S, there are also files related to USB there.
@TrinityHaxxorX have you try this ? just little help
That is pretty cool i didnt realise that you could just use winrar to open a APK file i have always used APKTOOL. I guess if anyone that has read my guide is reading this thread that can modify that part and it would be a whole lot easier. Good job.
Feel free to go and take a quick look at my post in my PAC thread if you want and chuck the details on how to do the whole ROM in here, will help people find the details a whole lot easier.
EDIT: Still suffers from the framework problem where you will get system_ui crashes so will have to use my second process just saves you going to command prompt and using APKTOOL.
Wow...nice... Happy news for acro s user... Good job bro...
Sent from my LT26w using xda premium
Hi friend's i rooted my U.K. xperia arc s build no 4.1.L.0.8 by following post of members in this forum but their build no was different i flashed kernel as per their guide and rooted my phone but after flashing ics kernel an update occurs
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
but in settings it shows build no 4.1.L.0.8 so someone plz share U.K LT18i xperia arc ics 4.1.L.0.8 kernel....
Thanks in advance...
Sent from my LT18i using xda premium
R: ICS Kernel for U.K. xperia arc s 4.1.L.0.8
..i like your systemui,could you please upload it?tnx
Inviato da me!
Here's a thread that has all sorts of info that might help -
http://forum.xda-developers.com/showthread.php?t=1653188
You can pick one of the ICS kernels - just need to read a bit on page one of each thread to see if the kernel works with a stock rom.
Enojy
Thanks
Sent from my LT18i using xda premium
Perfect guide for rooting U.K. Three Xperia Arc LT18i 4.1.L.0.8 only...
Rooting your mobile may void the warranty and you are doing it at your own risk. Sony would be in no way responsible for any damage...
Go to settings > Security > Mark "Unknown sources"
Settings > Developer options > Mark USB debugging
Settings > Xperia > connectivity > USB connection mode > select MSC mode
================================================== ==================================================
You should have
Flashtool
http://androxyde.github.com/Flashtool/
------Download------
1 ) Arc S - Kernel
http://www.4shared.com/file/qNTvdPI6/Lt18i_41A0562_Kernel.html
2) Go to C:/ Drive > flashtool > firmwares > delete everything present and Put the kernel
3) Run Flashtool click on the flashing icon ( left side below "file" option)
Select flashmode > ok
Setup should be like this > select OK
Follow the steps connect your mobile and flash.
Flashtool may show error after flashing kernel, no worries. Even your build number, android version won't change. Everything would remain same. So please don't go to phone settings to check anything
4) After flashing restart your device, It may not start completely, may remain at Sony logo or blank/black.
Whatever the status is, just restart your device and proceed with the rooting--->
( Make sure you close flashtool before running the rooting toolkit )
Now connect your mobile to PC and Root Your Phone
If you face problem in downloading the toolkit then here it is
http://www.mediafire.com/?7dp5k73by10inbf
[ READ THE FOLLOWING CAREFULLY! ]
This script will:__________
1.root ur device using "andorid emulator" trick
2.install Busybox (1.18.4)
3.install SU files (ICS specific)
4.do some checks for free space, tmp directory (will remove Google Maps if required)
Before u begin:___________
1.make sure u have installed adb drivers for ur device
2.enable "USB DEBUGGING" - from (Menu\Settings\Developer Options\Development)
3.enable "UNKNOWN SOURCES" - from (Menu\Settings\Security)
4.[OPTIONAL] increase screen timeout to 10 minutes
5.connect USB cable to PHONE and then connect to PC
6.skip "PC Companion Software" prompt on device
[ WARNING ]
make sure that no other adb server is running in background (e.g.: Flashtool, PCC, SEUS) and disable any antivirus
[ How to install? ]
1.extract ALL the files in the zip
2.now just double click on "runme.bat"
3.sit back read the on screen instructions
4.the device will reboot a couple of times
5.when the script finishes it will say "ALL DONE"
5) Download 4.1.L.0.8 Kernel here....
http://www.4shared.com/zip/u6W3yREf/LT18i_41L08_Kernel.html
Credits goes to Androxyde, Bin4ry, Doomlord
and
Dhruv Shah for uploading 4.1.L.0.8 Kernel
Sent from my LT18i using xda premium
This is a beginners tutorial on how to revert back to STOCK firmware using Flashtool by @Androxyde
I'm sure there must have been many more tutorials on this, but this post is modified for simplicity with image for new users.
Has Your Mobile
Soft Brick
Not Responding After A Mistake In Flash
Only LED Shows Green/Red/Blue Light
Bootloops Troubling?
Make the phone as good as new.
Then this guide will help you to recover your phone back to STOCK.
Things You Need Before Returning To Stock
Flashtool
ftf file for your Xperia S
NOTE : DO NOT CONNECT THE PHONE AT THE START. ONLY CONNECT WHEN ASKED BY FLASHTOOL
Here is a stock rar file for Xperia S ---> http://depositfiles.com/files/xjty40tgk
[FIRMWARE][6.1.A.2.45] World Generic
Click to expand...
Click to collapse
Now Lets Get Down To Business.
Flash it using latest version of Flashtool
1. Download the Firmware
2. Extract the .rar
3. Put the .ftf in <flashtool directory>/firmwares/
4. Run flashtool
5. Click flash or thunder icon
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
6. Flash mode, Ok
7. Select from left panel the correct firmware --> Lt26i 6.1.A.2.45 SG Generic (Your ftf File in firmware folder)
8. Click Ok!
9. OK ... Wait for a connection pop-up
10. Do not follow the instruction there, Just Connect Xperia S holding volume down button
11. Wait for installation to complete (When no more loading and the log shows Reboot and enable android debugging)
12. Unplug device and reboot
13. Close flashtool.
That Should Bring You Back To Stock!
If after that if you really want to bring your phone back to factory comdition.
For Making the Phone As Good As New
RELOCK THE BOOTLOADER that should do the trick!
For Relocking Flash the Attached "Xperia S Relock File" Given below
In The Same Manner Following Every Step.
In Step 7 Select Relock Xperia S File
Flash!
And You Are Done!
Hit Thanks if it Helped You!
This is covered in Soft Brick recover thread......
http://forum.xda-developers.com/showthread.php?t=1849170
s-X-s said:
This is covered in Soft Brick recover thread......
http://forum.xda-developers.com/showthread.php?t=1849170
Click to expand...
Click to collapse
Yes You Are Right!
But Any New User Will Not Like To Go Through Such A Long Process If HE/SHE is feeling helpless.
Again this is Modified for new users..
Giving them exactly what they want is top most priority.
Regards,
Dwarkesh Soren
My acro s become brick during relocking process...pls hlp me
it only shows "sony".
Ok I did fallow the directions. My ion does not respond to anything so first i removed the battery wire from motherboard for 5 minutes then I locked in on position volume - and connected it to pc with flashtool running with my firmware ready to flash. after few hours when I check it flasing tool command lanes have"Flashig finished, disconnect the device,for the flashing tool unknown sources and debugging must be check in,device connected in flash mode,device disconnected. Have only red led and pc companion does not recognize the phone . when disconnected from pc phone is dead nothing works. need help please:crying:.
me too
giri143 said:
My acro s become brick during relocking process...pls hlp me
it only shows "sony".
Click to expand...
Click to collapse
my sl too, you on phone until out off battery.
next reflash tock rom for your phone.
you try
good luck!!!
p/s: sorry, limited English!
To say that this is for bricked phones is inaccurate. These are the steps to follow when you want to flash any ROM, for whatever reason,even if your phone is working flawlessly.
Reseting Sim-unlock counter???
Will this also reset the sim-unlock counter????
will this work if i am currently using:
Xperia S - LT26i
Android Version: 4.1.2
Baseband Version: 8660-AAABQOLYM-314010-28
Kernel Version: 3.0.55-FXP+ [email protected] #1
CyanogenMod Version: 10-20121221-UNOFFICIAL-nozomi
hello.yesterday i tried to restore my DRM keys and when it said to restart my phone i pressed yes.then if closed down and now it wont open.sometimes when i press the power button the bottom lights up but the screen remains black.and sometimes when i hold volume up or down i get a flashing green light.just once.no vibrations and nothing.i tried to flash back the firmware but still nothing.black screen.and all that after i restored the drm keys.i was on existenz 2.5 rom.please can you help me?and now i just see the bottom right corner of XS lighting up and then off and then light again....is it destroyed?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is just a compilation of needed steps for newbies like myself, to root your phone and if you don’t wanna flash DooMLoRD’s pre-rooted firmare or anyother kernel stuff if it freaks you out (like it does to me), and until we’re not able to use RootManyAndroid by Bin4ry to root our Sony Xperia S
All credit’s go to DooMLoRD and the one’s who helped him achieve his goal.
This is for Unlocked BootLoaders ONLY
1) Install fastboot drivers (if you havent already) for your xperia S. (it will be a pain, but follow this): http://bit.ly/19VVFCW and download fastboot as well.
Here are the drivers: http://www.mediafire.com/download/7qpbpq65m7fj9dw/fb_drivers.zip
Here’s fastboot: http://www.mediafire.com/download/bzeetedlu0e6cxo/fastboot.zip
2) You need to install the custom recovery by DooMLoRD here
Code:
a) Download his files and create a folder “fastboot”
b) Place custom recovery file in that folder along with fastboot files
c) Turn off your phone
d) Plug your cable to phone
e) Pushing VolumeUp button enter on fastboot mode
f) Open the fastboot folder
g) Press shift+rightclick and choose open cmd window here
3) Follow these DooMLoRD instructions
Code:
type: fastboot flash boot S_DooMLoRD_AdvStkKernel_FW-200_v2.elf
4) enjoy your rooted phone
Source: Here and Here
For Locked or Unlocked BL ?
hiddenron said:
For Locked or Unlocked BL ?
Click to expand...
Click to collapse
Unlocked BL, like stated on DooMLoRD's thread. I've added the info to the post. Thanks.
Concise and pretty straightforward.
Rooted the world ftf firmware successfully.
Thanks.
aieromon said:
Concise and pretty straightforward.
Rooted the world ftf firmware successfully.
Thanks.
Click to expand...
Click to collapse
thanks for the feedback. that's what I was aiming for. it mean a lot. thanks again.
kudos
Will there be a way to do this but with Locked Bootloader?
naeem123 said:
Will there be a way to do this but with Locked Bootloader?
Click to expand...
Click to collapse
i really don't know. im no dev. just compiled the needed steps. but i hope so.
kudos
naeem123 said:
Will there be a way to do this but with Locked Bootloader?
Click to expand...
Click to collapse
No. You can't flash custom kernel with locked boatloader.
--
Xperia S: CM10 (FXP)
Milestone 2: CM7 (tezet)
Thread moved from Development to General, all guides belong in the General section.
Thanks
help please, some error in last step
ZACHARiAS_ said:
This is just a compilation of needed steps for newbies like myself, to root your phone and if you don’t wanna flash DooMLoRD’s pre-rooted firmare or anyother kernel stuff if it freaks you out (like it does to me), and until we’re not able to use RootManyAndroid by Bin4ry to root our Sony Xperia S
All credit’s go to DooMLoRD and the one’s who helped him achieve his goal.
This is for Unlocked BootLoaders ONLY
1) Install fastboot drivers (if you havent already) for your xperia S. (it will be a pain, but follow this): http://bit.ly/19VVFCW and download fastboot as well.
Here are the drivers: http://www.mediafire.com/download/7qpbpq65m7fj9dw/fb_drivers.zip
Here’s fastboot: http://www.mediafire.com/download/bzeetedlu0e6cxo/fastboot.zip
2) You need to install the custom recovery by DooMLoRD here
Code:
a) Download his files and create a folder “fastboot”
b) Place custom recovery file in that folder along with fastboot files
c) Turn off your phone
d) Plug your cable to phone
e) Pushing VolumeUp button enter on fastboot mode
f) Open the fastboot folder
g) Press shift+rightclick and choose open cmd window here
3) Follow these DooMLoRD instructions
Code:
type: fastboot flash boot S_DooMLoRD_AdvStkKernel_FW-200_v2.elf
4) enjoy your rooted phone
Source: Here and Here
Click to expand...
Click to collapse
Please help, i have done all this steps right, in the last step, when i past: type: "fastboot flash boot S_DooMLoRD_AdvStkKernel_FW-200_v2.elf", in the cmd window give this error:error: cant load 'S_DooMLorD_AdvStkKernel_FW-200_v2.elf', can anyone explain whats going wrong?
this its a print screen of error
Thanks
thanks a lot
BLu-RaymOn said:
thanks a lot
Click to expand...
Click to collapse
Yw
Kudos.
Sent from my A0001 using Tapatalk
please any one give me a solution how to get out of this problem..
i have redmi 1s , which is stuck at MI-Recovery 2.0.1
when i power on phone, its allways getting redirected to this recovery.. i havent ROOTED yet. the phone is not going to any further screen..
all this happened when i tried to install update.. now my phone is not at all detecting in the system also !
i have STABLE ROM which i downloaded from MI website, i renamed it and kept in MicroSD card as update.zip
but when i try to install it from MI-Recovery its saying update.zip not found.. please help me ..
i wish i wouldnt have downloded this update file:crying:
Relax, it's easy to recover your phone
Step 1:
a) Download & Install MiPhone flash tool from:
http://bigota.d.miui.com/tools/MiPhone2015731.exe
b)Download factory image to restore your device:
For MIUI 5 latest stable download : http://bigota.d.miui.com/JHCMIBL56.0/armani_global_images_JHCMIBL56.0_4.3_in_f29358d132.tgz
For MIUI 6 latest stable download: http://bigota.d.miui.com/V6.7.1.0.KHCMICH/armani_global_images_V6.7.1.0.KHCMICH_20150723.0000.6_4.4_global_3155609c91.tgz
c) Extract the archive into an easily accessible location
Step 2:
a) Open MiPhone app & click browse to select the folder where you extracted the rom
b) If your phone is in recovery mode take out it's battery for a second and put it back
c) Now start your phone in fastboot mode by pressing volume down and the power button simultaneously
d) Connect the phone to your pc and let it alone for 1 minute to allow windows to install its drivers
e) In MiPhone app click refresh and you should see a device appearing
f) Click Flash and don't touch your pc or phone until the job is done.
Further info / biography:
http://en.miui.com/a-234.html
Thank you very much
seth66 said:
Relax, it's easy to recover your phone
Step 1:
a) Download & Install MiPhone flash tool from:
http://bigota.d.miui.com/tools/MiPhone2015731.exe
b)Download factory image to restore your device:
For MIUI 5 latest stable download : http://bigota.d.miui.com/JHCMIBL56.0/armani_global_images_JHCMIBL56.0_4.3_in_f29358d132.tgz
For MIUI 6 latest stable download: http://bigota.d.miui.com/V6.7.1.0.KHCMICH/armani_global_images_V6.7.1.0.KHCMICH_20150723.0000.6_4.4_global_3155609c91.tgz
c) Extract the archive into an easily accessible location
Step 2:
a) Open MiPhone app & click browse to select the folder where you extracted the rom
b) If your phone is in recovery mode take out it's battery for a second and put it back
c) Now start your phone in fastboot mode by pressing volume down and the power button simultaneously
d) Connect the phone to your pc and let it alone for 1 minute to allow windows to install its drivers
e) In MiPhone app click refresh and you should see a device appearing
f) Click Flash and don't touch your pc or phone until the job is done.
Further info / biography:
http://en.miui.com/a-234.html
Click to expand...
Click to collapse
THank you very much bro, you have helped me a lot , i didnt see your reply till yesterday night.. i have flashed in the process which u said..
now its working perfectly ..
how do i know what is my MIUI version ? i some where saw its miui7 .. does it mean i am in miui7 ? my previous one was miui6 .. how can i know what is my version of miui ..?
SOLVED
oh its ok .. problem SOLVED :: :highfive::victory::fingers-crossed:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
finally i am in MIUI 7
Yeh Dude Its working fine for me........... Many Many thanks for this....
SAGAR SAVKAR
Lol I once had this problem