Related
I am running rooted stock 4.0.4 IMM76K with FC04/FC05 radios on a Verizon Nexus. I can not get the stock tethering or wifi tether to work. Both turn on without errors but none of my computers see the signal. I have always used wifi tether on other phones and not seen an issue. I have searched around but I can't seem to find anyone with my issues. Any suggestions?
I would try using an app like foxfi or pdanet. Both work well for wifi tethering. Also, both have the ability to hide tethering usage. You may have to sideload these apps, i believe Verizon wont let you get to them anymore. Also, I would no blow through my data allowence if I were you. This might cause them to get look a little more carefully at your data usage.
Try tetherbee.
It worked for me.
U must search online for it though.
gregory99mar said:
I would try using an app like foxfi or pdanet. Both work well for wifi tethering. Also, both have the ability to hide tethering usage. You may have to sideload these apps, i believe Verizon wont let you get to them anymore. Also, I would no blow through my data allowence if I were you. This might cause them to get look a little more carefully at your data usage.
Click to expand...
Click to collapse
Verizon still allows my mom to tether for free.
Even she'll get in trouble if she gets caught.
Would this be a rom or kernel issue? It doesn't seem to be a application issue? Many others have used both the options I have tried already without issues on the Nexus
drewcam888 said:
Would this be a rom or kernel issue? It doesn't seem to be a application issue? Many others have used both the options I have tried already without issues on the Nexus
Click to expand...
Click to collapse
AOKP unlocks and bypasses the tether message/error.
It's the stock rom issue it is disabled from what I was told.. I use aokp 39 using the built in tether and it works great
Sent from my Galaxy Nexus using Tapatalk 2
You need to set Wifi tether settings as follows:
Device Profile - Samsung Galaxy Nexus (CDMA/LTE)
Setup Method - Netd (master)
Routing Fix - make sure its checked.
Hope this helps
bgmikejr said:
You need to set Wifi tether settings as follows:
Device Profile - Samsung Galaxy Nexus (CDMA/LTE)
Setup Method - Netd (master)
Routing Fix - make sure its checked.
Hope this helps
Click to expand...
Click to collapse
This did not work any other suggestions?
DLD511 said:
AOKP unlocks and bypasses the tether message/error.
Click to expand...
Click to collapse
As stated before I have no error messages.
bryantjopplin said:
It's the stock rom issue it is disabled from what I was told.. I use aokp 39 using the built in tether and it works great
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
I forgot to mention that I installed a rom mod to enable native tethering.
I made a blunder. Apparently wifi tether didn't like the space I put in the SSID name.
drewcam888 said:
This did not work any other suggestions?
Click to expand...
Click to collapse
What version are you running as I am using wifi_tether_v3_1-beta14. If you dont have that version here you go http://goo.gl/UbxFo make sure the settings are the same as I posted above. Hope this helps
can you list all your settings
***Be sure to install SuperSu from the play store before following these steps so that this app will have proper root access***
1) Go here:
http://forum.xda-developers.com/showthread.php?p=34037922
2) READ THREAD INFORMATION
3) Download:
WifiTether-TrevE_Mod_11_22_2012_driverReload2 (defaults to Wifi Driver Reload 2) - http://www.androidfilehost.com/?fid=9390208427046731813
4) Disable Sprint Connections manager through settings menu
*System settings /more settings /mobile networks*
5) If any previous versions of WiFi tether are installed, UNINSTALL
6) Install new modded .apk
7) Use the following settings:
- Generic ICS/JB (wlan0) for Device Profile
- Netd-Ndc (master) for Setup Method
- Check box for "Send Netd Max Client Cmd"
- Make Sure "WiFi-driver reload 2" is checked
- Check Keep Alive Connection
- Check "Routing fix"
8) Reboot!
That should do it for you.
Encryption settings work as well.
Let me know if this works for you
Good guide. Anyway to get native 4G Tethering though?
Sent from my SPH-D710 using xda premium
locoboi187 said:
Good guide. Anyway to get native 4G Tethering though?
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
I haven't been able to get native 4g tethering to work since our ics days.. Something changed in jb and the wimax_service.jar file used from the og epic no longer works on our device (at least back in the day when I tried it). This I the best I've been able to do.
Sent from my SPH-D710 using xda premium
Also... Someone's please try not disabling the sprint connection manager.. See if this still works. May have effed myself.. Will revise op if someone tries and succeeds without following that step
Sent from my SPH-D710 using xda premium
Disregard. Must be disabled. I used titanium backup to freeze it. I am having a separate 3g issue with FK23. At least my 4g tethering works though... Lol
Sent from my SPH-D710 using xda premium
Thanks for this. I downloaded the modded app but couldn't get it working. I'll try your settings
DataHawg said:
Thanks for this. I downloaded the modded app but couldn't get it working. I'll try your settings
Click to expand...
Click to collapse
You may have to restart after the initial setup for things to work. I had to do this the first time, but not when I re flashed and tried again.
Sent from my SPH-D710 using xda premium
It works, but definitely needs a reboot and encryption does not work. I uninstalled sprint connection optimizer with TB and that totally f'd me. Had to reflash...
tek818 said:
It works, but definitely needs a reboot and encryption does not work. I uninstalled sprint connection optimizer with TB and that totally f'd me. Had to reflash...
Click to expand...
Click to collapse
I have encryption turned on right now. WPA2. Works perfectly. Also, the first time I simply froze Sprint Connection Manager. The 2nd time I just disabled it from within the app settings itself.
Works great for me when I follow the directions, thanks OP! Encryption is working for me also.
I was too busy to try this today but posted a link to your thread on Universe JB Rom thread. First user over there that tried it said it worked great. I froze Connection Optimizer with TB and now I'm glad I didn't uninstall it. Thanks again
Worked Great!!
I'm up and tethering again!!!!!
Thanks!!!!
I had this working for a bit, then had to reflash, and can't get it working again. Those of you that have it working, are you using superuser or supersu? One-click or the original tar leak?
ive tried three times to get this working i think the problem ive got is with the connection manager, can some one please explain how to disable it,i know this makes me sound stupid but an actual video would be cool too, any help would be appreciated, thank you8 i finallygot it working thank god jelly bean rocks and thanks for all the help, to disable connection manager i used tb 4,75 hopefully after i load apps it will work
I'm not on the leak anymore... But if I remember right...
Menu, settings, more (near the top under Wifi settings and such), connection manager, disable (uncheck box).
Again I only used fk23 for less than 24 hours so I don't remember the exact options.. Anyway, that would definitely be the reason why it's not working for you.
Sent from my SPH-D710 using xda premium
So I finally managed to get it working... I had to disable 4G or else my wifi devices would not see the SSID being broadcast by my phone. Once on 3G, my devices can now see the SSID broadcast and join the network. Interestingly enough, once the devices are successfully connected to the network, I can then enable 4G to use the additional bandwith.
tek818 said:
So I finally managed to get it working... I had to disable 4G or else my wifi devices would not see the SSID being broadcast by my phone. Once on 3G, my devices can now see the SSID broadcast and join the network. Interestingly enough, once the devices are successfully connected to the network, I can then enable 4G to use the additional bandwith.
Click to expand...
Click to collapse
That is a very odd scenario. Worked perfect for me..
Now that the devices can see your network and are connected to 4G can you turn the network off and on again and will they auto connect? Or do you need to revert to 3g every time? That would be a huge PITA
Sent from my SPH-D710 using xda premium
EmperorX said:
That is a very odd scenario. Worked perfect for me..
Now that the devices can see your network and are connected to 4G can you turn the network off and on again and will they auto connect? Or do you need to revert to 3g every time? That would be a huge PITA
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
Yes, it seems I only have to connect while on 3G once, then I can freely start and stop the network on 4g.
LIFESAVER! I played with FK23 for about a day but couldn't deal with the lack of 4G hotspot. So I had gone back to FI27 with the hotspot mod 'til I could find something like this. Works like a charm! Actually, my up and down speeds have increased from the FI27 hack, oddly. Stable Jellybean with working 4g tethering? I'll take it!
FYI: I just selected the device model along with the rest of the settings provided in the OP and it worked fine.
EmperorX said:
4) Disable Sprint Connections manager through settings menu
Click to expand...
Click to collapse
Where is Sprint Connections Manager?
Well I have read through the development thread of ktoonsez and task's kernel and rom and even used yes search in the thread and have come up with no answers. When I was on ICS I had no issue with Wi-Fi tethering but since I have moved to this rom I can create the hotspots however there is no internet connection. I found a couple posts in the thread using the search but they seem to be gone from the actual thread since after I click the link it's not on the page that pops up.
I am currently running both the ktoonsez & task rom and kernel (latest versions) on a bell I747m with MVLDLK4 modems on MTS . I don't have a tethering plan but when I was on ICS it didn't seem to matter. Can anyone help me out or point me in the right direction?
Sent from my SGH-I747 using xda app-developers app
Same Issue
kellz204 said:
Well I have read through the development thread of ktoonsez and task's kernel and rom and even used yes search in the thread and have come up with no answers. When I was on ICS I had no issue with Wi-Fi tethering but since I have moved to this rom I can create the hotspots however there is no internet connection. I found a couple posts in the thread using the search but they seem to be gone from the actual thread since after I click the link it's not on the page that pops up.
I am currently running both the ktoonsez & task rom and kernel (latest versions) on a bell I747m with MVLDLK4 modems on MTS . I don't have a tethering plan but when I was on ICS it didn't seem to matter. Can anyone help me out or point me in the right direction?
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
I have a similar issue. I want to get the mobile hot spot to work. But Im not sure what root I need to have that. What root were you using before to get your mobile hot spot to work? Thanks.
Gamerxx13 said:
I have a similar issue. I want to get the mobile hot spot to work. But Im not sure what root I need to have that. What root were you using before to get your mobile hot spot to work? Thanks.
Click to expand...
Click to collapse
If you are talking about using the WIFI Tether app Jelly Bean essentially broke it. The devs are working on a fix. XDA member Treve has a mod that will get it to work though. His OP is posted in the Verizon forums but I can assure you it works on our AT&T phones. I used it last night. There is an issue worth noting that once you tether and untether your WIFI won't work again until you clear cache and reboot. It is a minor annoyance IMO but I threw it out there so no one freaks out.
If you are talking about straight stock tethering I haven't run into the issue myself. My stock tether/WIFI hotspot works flawlessly. After updating to 4.1.1 did you do a full data wipe? If not I would recommend it. I ran into all kinds of bugs after doing the Kies update. Battery drain, Google Now had a learning disability, etc.
Do a google search for Treve WIFI Tether mod for the link and give it a go. In the OP he says that secure tethering doesn't work. It does. Used it last night as a test.
Also if you have a rooted phone already download mobile odin. You can have the app reflash the stock .tar and inject everoot and SuperSU. That's what I generally do when a new OTA is released. Hasn't failed me yet. Any questions shoot me a PM.
Sent from my Nexus 7 using xda premium
OmRomRom said:
If you are talking about using the WIFI Tether app Jelly Bean essentially broke it. The devs are working on a fix. XDA member Treve has a mod that will get it to work though. His OP is posted in the Verizon forums but I can assure you it works on our AT&T phones. I used it last night. There is an issue worth noting that once you tether and untether your WIFI won't work again until you clear cache and reboot. It is a minor annoyance IMO but I threw it out there so no one freaks out.
If you are talking about straight stock tethering I haven't run into the issue myself. My stock tether/WIFI hotspot works flawlessly. After updating to 4.1.1 did you do a full data wipe? If not I would recommend it. I ran into all kinds of bugs after doing the Kies update. Battery drain, Google Now had a learning disability, etc.
Do a google search for Treve WIFI Tether mod for the link and give it a go. In the OP he says that secure tethering doesn't work. It does. Used it last night as a test.
Click to expand...
Click to collapse
Wifi Tether works. The old version stopped working for me after upgrading to JB, but I downloaded a different beta. You have to download the TrevE Mod, wifi_tether_v3_3-pre2.apk.
Also I had to change some settings.
Device profile is set to GS3.
Fallback tether is enabled.
Send Netd Max Client Cmd is enabled.
Both Wifi-driver reload options are enabled.
MSS clamping is enabled.
Routing fix is enabled.
This works for me. Sometimes no data will come through but restarting my phone fixes the problem. I'm rooted on stock JB.
mjsierra said:
Wifi Tether works. The old version stopped working for me after upgrading to JB, but I downloaded a different beta. You have to download the TrevE Mod, wifi_tether_v3_3-pre2.apk.
Also I had to change some settings.
Device profile is set to GS3.
Fallback tether is enabled.
Send Netd Max Client Cmd is enabled.
Both Wifi-driver reload options are enabled.
MSS clamping is enabled.
Routing fix is enabled.
This works for me. Sometimes no data will come through but restarting my phone fixes the problem. I'm rooted on stock JB.
Click to expand...
Click to collapse
This Worked! You Sir are a genius, a gentleman and a scholar. THANKS!!
Had a similar issue for a long time, then stumbled onto this gem. Thanks a lot!!
mjsierra said:
Wifi Tether works. The old version stopped working for me after upgrading to JB, but I downloaded a different beta. You have to download the TrevE Mod, wifi_tether_v3_3-pre2.apk.
Also I had to change some settings.
Device profile is set to GS3.
Fallback tether is enabled.
Send Netd Max Client Cmd is enabled.
Both Wifi-driver reload options are enabled.
MSS clamping is enabled.
Routing fix is enabled.
This works for me. Sometimes no data will come through but restarting my phone fixes the problem. I'm rooted on stock JB.
Click to expand...
Click to collapse
So I know there are quite a few threads out there about wifi tether. The general concensus is that WiFi Tether is the best app to use, however I've found that very particular settings are needed to get this to work. While I am not a dev and have not had sucess in getting this app to work on our phone. I thought I would start a thread for those who have had success using the application in hopes that they could share their settings with the rest of us so we can take advantage of 4g as it continues to roll out. I have also tried Barnacle and not had any success either.
I found this on another thread, it was a couple pages deep so I'm reposting here, please swing over to other thread here http://forum.xda-developers.com/showthread.php?t=2138144&highlight=wifi+tether&page=2 #13 and give jdock a thanks for his fix. This works, but there is currently a bug in JB that only allows one tether session per boot. Once you disable wifi tether, it will not work again until you reboot the device
TY jdock
Try this:
device profile = generic ics/jb (wlan0)
setup method = netd-ndc (master)
wifi driver reload = checked
enable wifi encryption = unchecked (you can enable it later when it's working unencrypted)
enable access-control = unchecked (you can enable it later when the basics are working)
Now, when I first started with this app, my devices would connect to the AP but then give up because they couldn't get a dhcp address. I found that if I went into the 'change lan' menu and picked a different lan, that it started working (I currently use 10.10.3.0/24).
If you can't get it working, I came up with another method you may be able to use that does not use any app (I have the at&t model but it's probably the same). Basically you turn off wifi, then run a few commands (as root) that bring the wifi interface back up without disabling mobile data. It will connect to your local wireless lan as if you had enabled wifi. Then you can run a socks or http proxy and point your other device at it (easy if you're wanting to tether a pc, maybe not so easy if you're using something else). I haven't tried yet to see if it will route between the networks, which would mean you can just manually change your default gateway to your phone's wlan address and have all traffic go through it.
Anxiously awaiting
eeeeeeeeek said:
So I know there are quite a few threads out there about wifi tether. The general concensus is that WiFi Tether is the best app to use, however I've found that very particular settings are needed to get this to work. While I am not a dev and have not had sucess in getting this app to work on our phone. I thought I would start a thread for those who have had success using the application in hopes that they could share their settings with the rest of us so we can take advantage of 4g as it continues to roll out. I have also tried Barnacle and not had any success either.
Click to expand...
Click to collapse
I hope you get some answers. I haven't been able to get this app to work on by GNex on JB 4.2.1 OR 4.2.2 using 4 different ROMs. The app doesn't seem to have been updated in many months, and I'm assuming that it won't work on JB in any form.
stevesixty8 said:
I hope you get some answers. I haven't been able to get this app to work on by GNex on JB 4.2.1 OR 4.2.2 using 4 different ROMs. The app doesn't seem to have been updated in many months, and I'm assuming that it won't work on JB in any form.
Click to expand...
Click to collapse
I'm on a JB rom now, and it does work. See the directions I posted from another thread in the OP and wifi tether will work. However, once you turn off wifi tether you will need to reboot the phone for wifi and data to function normally.
Even when Wi-Fi tether runs "with errors" it still works... for some reason my phone doesn't heat up as much when I run with errors -- probably had something to do with the Wi-Fi driver that the app reloads.
Sent from my LG-LS970 using xda app-developers app
eeeeeeeeek said:
I'm on a JB rom now, and it does work. See the directions I posted from another thread in the OP and wifi tether will work. However, once you turn off wifi tether you will need to reboot the phone for wifi and data to function normally.
Click to expand...
Click to collapse
My wifi tether setup has no issues with data not working and I can turn it off and on without problems. I've used the phone for calls, texts, and internet after using wifi tether. The only issue is that you cannot turn wifi on after running tether. Once rebooted wifi will turn back on until I use tether again. I'm on a stock rooted JB rom.
Generic ics/jb Wlan0
Netd ndc master
Send Netd max client cmd checked
wifidriver reload checked
Router fix checked
Wifi fix checked
I have access control checked as well but that doesn't matter.
I've yet to be able to get this app working. I've tried these setting before and several other settings to no avail. When I try these, everything but the first item in the log and the last two say they failed. Now it does broadcast it's SSID and I can join the network, but there is no data connection.
I'm on stock Jelly Bean rom. The funny thing is, I used Wifi tether app on Lifeless and Imperium and it worked with a few different settings.
Check your version. I use WIFI Tether TrevE Mod.
Mine version is 3.2-beta2-modv5 ***synergized***
I had similar issues until I found the right version to use. I never got regular Wifi Tether to work.
bruiserman said:
Check your version. I use WIFI Tether TrevE Mod.
Mine version is 3.2-beta2-modv5 ***synergized***
I had similar issues until I found the right version to use. I never got regular Wifi Tether to work.
Click to expand...
Click to collapse
You got a link to that version I don't see it in the thread with all the other versions. All I see are versions dated 11/20 or 11/22, no beta's or anything called synergized that I see.
flukeSG2 said:
You got a link to that version I don't see it in the thread with all the other versions. All I see are versions dated 11/20 or 11/22, no beta's or anything called synergized that I see.
Click to expand...
Click to collapse
I had the apk file somewhere, I'll look for it.
Send me a pm, I found the apk.
Try this one.
bruiserman said:
Try this one.
Click to expand...
Click to collapse
Thanks I'll let you guys know if it works.
Edit: Nah, still doesn't work with that copy with all the settings checked in the OP. Everything fails still.
---------- Post added at 05:36 PM ---------- Previous post was at 05:26 PM ----------
flukeSG2 said:
Thanks I'll let you guys know if it works.
Edit: Nah, still doesn't work with that copy with all the settings checked in the OP. Everything fails still.
Click to expand...
Click to collapse
By Changing some settings I can get everthing to work EXCEPT for the Nat Rules, that fails still. If someone can tell me how to fix that perhaps I can get this to work. Seems though the Nat Rules keeps my laptop from detecting the new network I made.
flukeSG2 said:
Thanks I'll let you guys know if it works.
Edit: Nah, still doesn't work with that copy with all the settings checked in the OP. Everything fails still.
---------- Post added at 05:36 PM ---------- Previous post was at 05:26 PM ----------
By Changing some settings I can get everthing to work EXCEPT for the Nat Rules, that fails still. If someone can tell me how to fix that perhaps I can get this to work. Seems though the Nat Rules keeps my laptop from detecting the new network I made.
Click to expand...
Click to collapse
Glad to see other people are able to contribute. I'm not a developer so not much I can do except dig around other forums and see what helps. I'm using Imperium Initiative v2.0.1 with wifi tether, with the settings in my op. Maybe there are some adjustments in imperium/lifeless that cause this to work. I will try the file posted and report back to see if I can re-enable wifi after disabling tether.
BUMP!
eeeeeeeeek said:
Glad to see other people are able to contribute. I'm not a developer so not much I can do except dig around other forums and see what helps. I'm using Imperium Initiative v2.0.1 with wifi tether, with the settings in my op. Maybe there are some adjustments in imperium/lifeless that cause this to work. I will try the file posted and report back to see if I can re-enable wifi after disabling tether.
Click to expand...
Click to collapse
Bump!
This one works for me with these settings:
Generic ics/jb Wlan0
Netd-Ndc (master)
Send Netd max client cmd - checked
Enable WiFi-Encryption - checked
WiFi-driver reload 2 - checked
Enable Access-Control - checked (If this is checked the first time the client connects, you have to grant it access from your phone. You'll notice a new icon on the top of your phone where all of your running program icons are. When you see it just pull down the list and select it and check your client and then hit apply)​Routing fix - checked
Hope this helps
something probably worth mentioning on this, I'm currently on Lifeless 14, and the connections optimizer was screwing with this app. I turned it off and it worked like a charm.
Not of concern to anyone AOSP/AOKP/CM/PA but for stock/lifeless/imperium(i think) this is worth looking into for some folks.
eeeeeeeeek said:
So I know there are quite a few threads out there about wifi tether. The general concensus is that WiFi Tether is the best app to use, however I've found that very particular settings are needed to get this to work. While I am not a dev and have not had sucess in getting this app to work on our phone. I thought I would start a thread for those who have had success using the application in hopes that they could share their settings with the rest of us so we can take advantage of 4g as it continues to roll out. I have also tried Barnacle and not had any success either.
I found this on another thread, it was a couple pages deep so I'm reposting here, please swing over to other thread here http://forum.xda-developers.com/showthread.php?t=2138144&highlight=wifi+tether&page=2 #13 and give jdock a thanks for his fix. This works, but there is currently a bug in JB that only allows one tether session per boot. Once you disable wifi tether, it will not work again until you reboot the device
TY jdock
Try this:
device profile = generic ics/jb (wlan0)
setup method = netd-ndc (master)
wifi driver reload = checked
enable wifi encryption = unchecked (you can enable it later when it's working unencrypted)
enable access-control = unchecked (you can enable it later when the basics are working)
Now, when I first started with this app, my devices would connect to the AP but then give up because they couldn't get a dhcp address. I found that if I went into the 'change lan' menu and picked a different lan, that it started working (I currently use 10.10.3.0/24).
If you can't get it working, I came up with another method you may be able to use that does not use any app (I have the at&t model but it's probably the same). Basically you turn off wifi, then run a few commands (as root) that bring the wifi interface back up without disabling mobile data. It will connect to your local wireless lan as if you had enabled wifi. Then you can run a socks or http proxy and point your other device at it (easy if you're wanting to tether a pc, maybe not so easy if you're using something else). I haven't tried yet to see if it will route between the networks, which would mean you can just manually change your default gateway to your phone's wlan address and have all traffic go through it.
Click to expand...
Click to collapse
These settings worked for me using the Stock Odex JB 4.1 rom. and the TrevE mod version below. I had to reboot first after installing the apk, and reload the binaries.
throttling
Well since it seems the tethering problem hasn't been remedied yet (touchy and have to restart), has anyone figured out a way to get around sprint's throttling? Unfortunately I for the life of me can't get my MSL, and also unfortunately I hate using the phone to call sprint. hrm.
May I suggest jellybeer? Tethering is built in!
Sent from my LG-LS970 using xda app-developers app
Now that S-OFF is available and many people have root, I thought I would help everyone get Wifi Tether working.
Download the attached APK. WifiTether APK
It's available all over the internet, so I don't have a link to the source.
Use the following settings (you must have root):
Device-Profile: Generic ICS/JB (wlan0)
Setup-Method: Auto
Enable Wifi-Encryption: Checked
Change SSID and Passphrase to your liking
Wifi-driver reload: Unchecked
Wifi-driver reload 2: Checked
MSS clamping: Checked
Routing fix: Checked
That should do it. Hope that helps anyone that was having issues. Start tethering and grant superuser permissions. It may ask you to grant twice. Make sure you accept both.
Enjoy!
This will appear as a regular AP, not via ad-hoc.
Not working here. Starts without errors but I can't see it as an available on any device
Edit: got it working using this app version: https://db.tt/pMu7HVV1. Settings as follows:
Generic ics/jb (wlan0)
WiFi encryption
WiFi driver reload
Unchecked everything else and it works perfectly . Thanks for the guidance and post.
HTC One and Only
SSID doesn't broadcast.
Windows 8 showed a hidden network.
Entered the SSID/password and it worked perfectly.
Verified on an iPad as well.
hotelmrrsn said:
Not working here. Starts without errors but I can't see it as an available on any device
Edit: got it working using this app version: https://db.tt/pMu7HVV1. Settings as follows:
Generic ics/jb (wlan0)
WiFi encryption
WiFi driver reload
Unchecked everything else and it works perfectly . Thanks for the guidance and post.
HTC One and Only
Click to expand...
Click to collapse
That's strange. The settings above worked on two HTC ones and a Droid DNA. Sorry it didn't work for you. I'll post up a short video.
VA_Joe said:
SSID doesn't broadcast.
Windows 8 showed a hidden network.
Entered the SSID/password and it worked perfectly.
Verified on an iPad as well.
Click to expand...
Click to collapse
That's interesting. I will take a look into it. If I change the SSID, it immediately shows the new network name.
Is everyone starting with Wifi off?
isdnmatt said:
That's strange. The settings above worked on two HTC ones and a Droid DNA. Sorry it didn't work for you. I'll post up a short video.
Click to expand...
Click to collapse
No problem! Mine was probably assembled on a Monday morning. =-O
HTC One and only
I did this:
http://forum.xda-developers.com/showpost.php?p=46463396&postcount=34
I did change the SSID (as I always do) and used the wifi tether posted in that comment. Worked without security. Did not try to set any up since I was testing and only use tethering about 3 times a year...
I use Wireless Tether 3.2 Beta 2. Have used it since it came out. I have tried newer versions that didn't work for me, and always went back to this one.
Device profile: Generic ICS/JB (wlan0)
Setup method: Netd-Ndc (master)
And enable access control
That setup has worked on multipe Viper Rezounds, Viper DNAs, and this NOS One.
freddie813 said:
I use Wireless Tether 3.2 Beta 2. Have used it since it came out. I have tried newer versions that didn't work for me, and always went back to this one.
Device profile: Generic ICS/JB (wlan0)
Setup method: Netd-Ndc (master)
And enable access control
That setup has worked on multipe Viper Rezounds, Viper DNAs, and this NOS One.
Click to expand...
Click to collapse
I'm using same app for my rooted ONE. I did not have to adjust the setup to netd-ndc, however.
Thank You
I just got my HTC One this week off Swappa ! came from step child Droid Bionic. So far
S-off
[ROM] BoneStock v1.2 (ty)
I did firmware update to .10
No red text
Now Wiresless tethering works again! ( sad thing only need 100 megs download my nook stuff )
Thank You
Mardoon
PS - I am loving a 100% unlock Phone! reminds me of my droid day's
Hi,
I just upgraded to kitkat. Using the setings mentioned above, when I try to start the tether it appears to hang. Are the settings different under kitkat?
rlewis19 said:
Hi,
I just upgraded to kitkat. Using the setings mentioned above, when I try to start the tether it appears to hang. Are the settings different under kitkat?
Click to expand...
Click to collapse
Look under apps n theme for WiFi hotspot
if I have helped you please press the thanks button.
There is s thread that allows you to enable the native tethering if you want to keep the stock operating system and not use an aftermarket Rom. It's a lot less hassle than trying to get WiFi tether to work. Most Roms out already has native tethering working. I feel the connection is way better using the native tethering over the app.
Sent from my HTC6500LVW using Tapatalk