Help recover my Galaxy note 2 - Galaxy Note II Q&A, Help & Troubleshooting

hey
an hour ago i got this massage on my phone after trying to recover my note 2
E:failed to find "cache" partition to mount at "/cache"
E:Can't mount /cache/recovery/log
E:Can't open /cache/recovery/log
E:failed to find "cache" partition to mount at "/cache"
E:Can't mount /cache/recovery/last_log
E:Can't open /cache/recovery/last_log
E:Can't find misc
E:failed to find "cache" partition to mount at "/cache"
and i tried to recover it again using odin but this is the result
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
and the mobile not working now the only thing that works is odin mode so plz help mee
sorry for my bad language

architect_zr said:
hey
an hour ago i got this massage on my phone after trying to recover my note 2
E:failed to find "cache" partition to mount at "/cache"
E:Can't mount /cache/recovery/log
E:Can't open /cache/recovery/log
E:failed to find "cache" partition to mount at "/cache"
E:Can't mount /cache/recovery/last_log
E:Can't open /cache/recovery/last_log
E:Can't find misc
E:failed to find "cache" partition to mount at "/cache"
and i tried to recover it again using odin but this is the result
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
and the mobile not working now the only thing that works is odin mode so plz help mee
sorry for my bad language
Click to expand...
Click to collapse
simply flash the stock firmware using Odin. remember to use pit for note2 in odin while flashing stock,, . happy flashing

tornado92 said:
simply flash the stock firmware using Odin. remember to use pit for note2 in odin while flashing stock,, . happy flashing
Click to expand...
Click to collapse
i didn`t understand :S

I don't know why to use pit. Whenever I flash my phone, I only use PDA, then PIT is for what? can anyone explain to me?
Sent from my GT-N7100 using xda app-developers app

Read Dr. Ketan guide
Pit file is only used under proper expertise.
Sent from my GT-N7100 using xda premium

aukhan said:
Read Dr. Ketan guide
Pit file is only used under proper expertise.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
how can i use it

architect_zr said:
how can i use it
Click to expand...
Click to collapse
Have a look at this: http://forum.xda-developers.com/showpost.php?p=32273406&postcount=5
N7100XXDLL7 FACTORY Firmware has a PIT file. You have to check 'Re-partition' box in Odin and put this PIT file in the related field.

Memphis_ said:
Have a look at this: http://forum.xda-developers.com/showpost.php?p=32273406&postcount=5
N7100XXDLL7 FACTORY Firmware has a PIT file. You have to check 'Re-partition' box in Odin and put this PIT file in the related field.
Click to expand...
Click to collapse
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_XEF_N7100OXADLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
this is what i got and this takes ages and still the problem n`t solved :S

Memphis_ said:
Have a look at this: http://forum.xda-developers.com/showpost.php?p=32273406&postcount=5
N7100XXDLL7 FACTORY Firmware has a PIT file. You have to check 'Re-partition' box in Odin and put this PIT file in the related field.
Click to expand...
Click to collapse
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_XEF_N7100OXADLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)

architect_zr said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_XEF_N7100OXADLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Are you sure you connected in download mode? Turnyour phone off and connect by usb cable and run odin. Some say that worked.
Sent from my GT-N7105 using xda premium

xcly said:
Are you sure you connected in download mode? Turnyour phone off and connect by usb cable and run odin. Some say that worked.
Sent from my GT-N7105 using xda premium
Click to expand...
Click to collapse
this is what i see

plz guys help me

architect_zr said:
plz guys help me
Click to expand...
Click to collapse
can your phone boot?? stucked at Samsung logo?? please at this stage dont try to flash bootloaders..

tornado92 said:
can your phone boot?? stucked at Samsung logo?? please at this stage dont try to flash bootloaders..
Click to expand...
Click to collapse
so what i should do in this stage :S

architect_zr said:
so what i should do in this stage :S
Click to expand...
Click to collapse
can your phone boot?? stucked at Samsung logo??

architect_zr said:
so what i should do in this stage :S
Click to expand...
Click to collapse
Start from scratch. Close Odin.
1. Make sure you have samsung drivers (install kies and then make sure it's not running)
2. Open odin. Choose firmware in the PDA section. Dont touch anything else.
3. Boot your phone into download mode (vol down home power).
4. Connect to pc using cable.
5. Press start.
If the above doesnt work (you said pit file werent there in the previous post), get the correct pit file and select it for pit section and select repartition on odin while doing number 2 as above
Sent from my GT-N7105 using xda premium

xcly said:
Start from scratch. Close Odin.
1. Make sure you have samsung drivers (install kies and then make sure it's not running)
2. Open odin. Choose firmware in the PDA section. Dont touch anything else.
3. Boot your phone into download mode (vol down home power).
4. Connect to pc using cable.
5. Press start.
If the above doesnt work (you said pit file werent there in the previous post), get the correct pit file and select it for pit section and select repartition on odin while doing number 2 as above
Sent from my GT-N7105 using xda premium
Click to expand...
Click to collapse
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
am i doing it wrong ?
or should i send it to pro people ?

architect_zr said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
am i doing it wrong ?
or should i send it to pro people ?
Click to expand...
Click to collapse
You should see some more messages come up after PIT mapping..
Have you tried different firmwares? Different odin version? Used a different USB port? Try flashing CWM using odin and see if that works.

architect_zr said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALJ3_N7100OJVALJ2_N7100XXALJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
am i doing it wrong ?
or should i send it to pro people ?
Click to expand...
Click to collapse
it could be SDS .. anyways goodluck brother

architect_zr said:
so what i should do in this stage :S
Click to expand...
Click to collapse
You should calm down and stop panicking. YOU are the only one who can see YOUR phone and it's responses.
You have to describe it to us so that WE can understand your problem.
Start with Why you needed to recover it in the first place

Related

[Q] Problems flashing I9082 with any ROM

Hello, XDA.
I'm having some trouble using Odin to flash my brand-new chinese I9082.
I successfuly flashed CWM Touch 6.0.3.6 with Odin 3.09 and I'm able to access CWM through PWR+VOL.UP+HOME anytime I want.
However, when I try to flash any other rom I could find online, I get problems when NAND writing.
My Odin screen says:
Code:
[FONT="Courier New"][COLOR="Red"]ODIN MODE[/COLOR]
PRODUCT NAME: GT-I9082I_VE
CUSTOM BIN DOWN: Yes (6 counts)
CURRENT BIN: Custom
SYSTEM STATUS: Official[/FONT]
I've tried the following roms:
I9082ZNAMJ1_I9082CHUAMJ1_CHU (PDA only)
I9082XXUBMJ3_I9082ODDBMJ1_INS (PDA only)
I9082XXUBMGA_I9082XXUBMGA_SER (PDA only)
I9082XXUBMGA_I9082OXEBMGA_SER (PDA only)
I9082XXUBMF2_I9082OXABMF2_OXA (PDA, Modem, CSC, Boot and PIT)
During the first four attempts, I got the following Odin output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
During the last one (with all the files), I get the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when I try to boot my phone, I get stuck at the splash screen.
What else can I do to flash my phone?
Thank you very much!
Best regards.
Just do it again but before dat make check on re partioned. Hope i heled
Sent from my GT-S5282 using XDA Premium 4 mobile app
stephenkall said:
Hello, XDA.
I'm having some trouble using Odin to flash my brand-new chinese I9082.
I successfuly flashed CWM Touch 6.0.3.6 with Odin 3.09 and I'm able to access CWM through PWR+VOL.UP+HOME anytime I want.
However, when I try to flash any other rom I could find online, I get problems when NAND writing.
My Odin screen says:
Code:
[FONT="Courier New"][COLOR="Red"]ODIN MODE[/COLOR]
PRODUCT NAME: GT-I9082I_VE
CUSTOM BIN DOWN: Yes (6 counts)
CURRENT BIN: Custom
SYSTEM STATUS: Official[/FONT]
I've tried the following roms:
I9082ZNAMJ1_I9082CHUAMJ1_CHU (PDA only)
I9082XXUBMJ3_I9082ODDBMJ1_INS (PDA only)
I9082XXUBMGA_I9082XXUBMGA_SER (PDA only)
I9082XXUBMGA_I9082OXEBMGA_SER (PDA only)
I9082XXUBMF2_I9082OXABMF2_OXA (PDA, Modem, CSC, Boot and PIT)
During the first four attempts, I got the following Odin output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
During the last one (with all the files), I get the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when I try to boot my phone, I get stuck at the splash screen.
What else can I do to flash my phone?
Thank you very much!
Best regards.
Click to expand...
Click to collapse
first boot in recovery and wipe data /reset and then flash the firmware and make sure that only auto reboot and f.reset time is ticked
rutvikrvr said:
first boot in recovery and wipe data /reset and then flash the firmware and make sure that only auto reboot and f.reset time is ticked
Click to expand...
Click to collapse
Thanks for your reply!
I did that. after that, with the chinese rom, I got the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I wiped everything again and tried to repartition with baffin PIT file. Got this output:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But whenever I try to flash the rom, I get this output:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> BcmBoot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
By the way, I tried in two different computers but I have the same results in both.
Is there anywhere I can download a different PIT file to try it?
stephenkall said:
Thanks for your reply!
I did that. after that, with the chinese rom, I got the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082ZNAMJ1_I9082CHUAMJ1_I9082ZNAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I wiped everything again and tried to repartition with baffin PIT file. Got this output:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But whenever I try to flash the rom, I get this output:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOT_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9082XXUBMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9082XXUBMF2_REV05.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9082OXABMF2_871997_REV05_user_mid_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> BcmBoot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
By the way, I tried in two different computers but I have the same results in both.
Is there anywhere I can download a different PIT file to try it?
Click to expand...
Click to collapse
u dont need a pit file .....just uncheck repartition .........and make sure u do a data wipe before and after installing
rutvikrvr said:
u dont need a pit file .....just uncheck repartition .........and make sure u do a data wipe before and after installing
Click to expand...
Click to collapse
I only check re-partition when I'm using a pit file. The PDA-only roms didn't have "re-partition" checked but they also didn't work.
I'm guessing from the errors that my partition is somehow buggy, that's why I wanted another partition file (and I can't seem to find it anywhere).
http://www.4shared.com/file/Inh_xaXn/baffin.html here u go
rutvikrvr said:
http://www.4shared.com/file/Inh_xaXn/baffin.html here u go
Click to expand...
Click to collapse
stephenkall said:
I only check re-partition when I'm using a pit file. The PDA-only roms didn't have "re-partition" checked but they also didn't work.
I'm guessing from the errors that my partition is somehow buggy, that's why I wanted another partition file (and I can't seem to find it anywhere).
Click to expand...
Click to collapse
Thank you very much!
However, my problem looks persistent. After I repartitioned the cellphone with your file, I tried another rom and I got the following output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXUBMGA_I9082OXEBMGA_I9082XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> vc-firmware.img
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> BcmCP.img
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I can see the beginning of the progress bar in odin screen.
which fw were u on 4.1.2 or 4.2.2??
rutvikrvr said:
which fw were u on 4.1.2 or 4.2.2??
Click to expand...
Click to collapse
I believe it was the stock chinese 4.1.2.
stephenkall said:
I believe it was the stock chinese 4.1.2.
Click to expand...
Click to collapse
Got it.
I was trying to flash I9082I with I9082 roms.
I downloaded one rom from a chinese website and it solved my problems.
Now I'm using:
Android 4.1.2
Firmware I9082iZNAMJ1
Kernel 3.0.31-1451271
Build JZO54K

Can't Flah CWM

Hello,
why i can't flash CWM at my Grand?
everything looks good but on odin this message appear :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.19.3-i9082.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
any one knows about my problem?and how to solve my problem? need you help plz
Thank you.
yoga.reks said:
Hello,
why i can't flash CWM at my Grand?
everything looks good but on odin this message appear :
any one knows about my problem?and how to solve my problem? need you help plz
Thank you.
Click to expand...
Click to collapse
lol your log reads philztouch tar.
hmm,
Try again with the tar file for clockwordmod recovery

Note 2 (N7100) stuck on white screen

Hi All
my Samsung Note 2 , stuck on white screen so i cant boot into recovery or download mode.
please help me how to fix this.
ahmad83it said:
Hi All
my Samsung Note 2 , stuck on white screen so i cant boot into recovery or download mode.
please help me how to fix this.
Click to expand...
Click to collapse
Try to flash stock / custom rom using odin
i tried Odin it shows :-
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFND4_N7100OJVFND3_N7100XXUFND3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
ahmad83it said:
i tried Odin it shows :-
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFND4_N7100OJVFND3_N7100XXUFND3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
try THIS
or
THAT
if you can't get it to work, then maybe you have hardware issue with emmc

S4 mini gt-I9195 help please

I want to put my stock firmware on my sgs4 mini gt-I9195 but when i flash with odin its says
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195QXXCOA1_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
<ID:0/020> Initialzation..
<ID:0/020> Set PIT file..
<ID:0/020> DO NOT TURN OFF TARGET!!
<ID:0/020> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I cant go in recovery mode
I cant flash anything on the phone, its says this error.
P.S i flashed with pit, without pit says pit error
try to flash with this firmware mate.
https://www.androidfilehost.com/?fid=24459283995298339
I will try but, anything what i try to flash dont work, i try to flash twrp its dont work its says this error..
It failed with same error
this is multifile frimware it should not fail did u tried to select pit from file as well?
Yes, i selected pit too
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I9195XXUCNH5_2659908_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> AP_I9195XXUCNH5_2659908_REV01_user_low_ship_MULTI_CERT_.tar.md5 is valid.
<OSM> CP_I9195XXUCNH5_2659908_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_OJV_I9195OJVCNH1_2502401_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
That's it.
xRENAMEx said:
I want to put my stock firmware on my sgs4 mini gt-I9195 but when i flash with odin its says
I cant go in recovery mode
I cant flash anything on the phone, its says this error.
P.S i flashed with pit, without pit says pit error
Click to expand...
Click to collapse
I had the sam Problem too...
It's a Hardware Problem (Motherboard)
Maybe you can buy an other used s4mini from eBay with working Motherboard and Exchange it.

SM-T900 can't install stock rom. Failure with Odin: there is no PIT partion

Using Unofficial LineageOS 14.1 (v2awifi). During using my Tab Pro 12.2 SM-T900 I got a failure and switched off my tablet. Since that time I can't start my tablet. Can only turn on my tablet in downloadmode. Can't enter recovery. Tried to flash TWRP, but that is not possible. Because the failure was suddenly, I could not and can't switch and change usb-debugging and media-transfer possiblities.
I tried to install Stock Rom with Odin, got the next faillures:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
And sometimes:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
So I can't flash the stock rom for repairing my ROM. Please help me, so that I can use my tablet again. How to fix PIT-partion ?
I have the same problem. Any resolution?
Same but on an SM-T320. Flashed an appropriate PIT, stock firmware...nothing working. I'm thinking it's a physical issue at this point.

Categories

Resources