Hello,
I still have a problem with pc detecting. I make a picture from my bootloader screen.
I think this is not normal. How is yours?
But in recovery mode the mass storage visible.
That's because you have the usb cable hooked on .... take it off and repeat all precious steps. No such messages again
Mr Hofs said:
That's because you have the usb cable hooked on .... take it off and repeat all precious steps. No such messages again
Click to expand...
Click to collapse
hmmm,it was not pluged in at that time.This happend when i pluged out.
Oke....and what if you enter the bootloader - hboot - recovery without a cable attached from the beginning. Could be bad timing while unplugging it
Mr Hofs said:
Oke....and what if you enter the bootloader - hboot - recovery without a cable attached from the beginning. Could be bad timing while unplugging it
Click to expand...
Click to collapse
Everything as going well, exept PC dosent detect the device
Its any way to put data to the mass storage? If i can put a ROM and installing, i can use the phone without usb connection.
Nah i mean :
Enter the bootloader without a cable connected, hook the cable once you are in and flash the boot.img, unhook it again and enter the recovery and then connect the usb cable once again.....mount the sdcsrd and copy a rom.....install a new rom
Hello everybody. I have next problem: when I try to connect my HOX to computer in mass storage mode, nothing happens on the computer. However on the phone everything goes as it has to go. I have CM 10.2 RC1 installed. And I've noticed one thing: when I get into the fastboot menu and then connect the device to the computer, the phone gets freezed. When I disconnect the device, everything goes well again.
Timofey_K said:
Hello everybody. I have next problem: when I try to connect my HOX to computer in mass storage mode, nothing happens on the computer. However on the phone everything goes as it has to go. I have CM 10.2 RC1 installed. And I've noticed one thing: when I get into the fastboot menu and then connect the device to the computer, the phone gets freezed. When I disconnect the device, everything goes well again.
Click to expand...
Click to collapse
I am glad to tell you that the problem had solved! I did next acts: typed in the command line 'pnputils -e', so I could see all drivers I have installed and their 'oem*.inf' files. I had 4 HTC drivers, it was like they were in a conflict. Then I deleted each driver with such command: 'pnputils -f -d <oem file name>'. So after that, I plugged in the cable and the HOX was recognized by the computer! Please tell me if you had the same problem and it was solved by the method above!
Sent from my HTC One X using xda-developers app
Related
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device
Whilst reflashing my diamond touch with a new rom at the stage where you disconnect and hold vol down and back button to start the rom off I had the back off and the battery fell out. Now if I do the above it comes up saying no image found then says trigger usb host and red flash saying usb retry enter usb. Have I meesed my phone up or is there a way to get the image back any help will be welcomed. I can still connect via mtty but the device doesn't come up in my computer anymore or wont connect via active sync.
tonictone said:
Whilst reflashing my diamond touch with a new rom at the stage where you disconnect and hold vol down and back button to start the rom off I had the back off and the battery fell out. Now if I do the above it comes up saying no image found then says trigger usb host and red flash saying usb retry enter usb. Have I meesed my phone up or is there a way to get the image back any help will be welcomed. I can still connect via mtty but the device doesn't come up in my computer anymore or wont connect via active sync.
Click to expand...
Click to collapse
dont worry .. nothing is lost
bring up the phone in bootloader .. vol down reset
connect the usb cable, on screen should write USB (instead of serial)
and now just run the customRUU.exe file that is usualy in archive you downloaded the rom, and just follow the instruciotions.
(like you are flashing without mtty! from computer)
hi man, have you tryed to reinstall drivers ? i don't know what happends to your phone but i'm really sad for you hope it's nothing That can seriously damage it so if i was you, i'll try to reinstall all drivers and use mtty from the 1st step, may be it will work. feed beck plz
R.seed said:
hi man, have you tryed to reinstall drivers ? i don't know what happends to your phone but i'm really sad for you hope it's nothing That can seriously damage it so if i was you, i'll try to reinstall all drivers and use mtty from the 1st step, may be it will work. feed beck plz
Click to expand...
Click to collapse
Now if I do the above it comes up saying no image found then says trigger usb host
Click to expand...
Click to collapse
he forgot to put image on the phone, or to rename it diamimg.nbh ...
reinstall DRIVERS !?
vicai said:
he forgot to put image on the phone, or to rename it diamimg.nbh ...
reinstall DRIVERS !?
Click to expand...
Click to collapse
yes..youre right..i did the same thing, after i've mtty (after type task 8), i forgot to initiate ROM flash and did hard reset+clear memory, so the image (diamimg.nbh) in movinand memory is erased.
So, we still can flash with custom RUU. bring your device in bootloader, you will see serial mode change into usb, then execute custom RUU.exe. follow the instruction.. but make sure your battery is enough..
Hope it help you..
Thanxs Vicai, did as your post recommended and working fine now, thanxs for the quick response
tonictone said:
Thanxs Vicai, did as your post recommended and working fine now, thanxs for the quick response
Click to expand...
Click to collapse
welcome
glad to help
Today when i connected my Phone to PC, it rebooted.
My phone is UNROOT. So please help me.
It happened 2-3times whenever i connected my phone to PC.
hd2_iFan said:
Today when i connected my Phone to PC, it rebooted.
My phone is UNROOT. So please help me.
It happened 2-3times whenever i connected my phone to PC.
Click to expand...
Click to collapse
Which mode you selected? Is it charge only or storage option. If it is storage option, try using another card and then connecting to comp to check whether its a problem with SD card
bezbeV said:
Which mode you selected? Is it charge only or storage option. If it is storage option, try using another card and then connecting to comp to check whether its a problem with SD card
Click to expand...
Click to collapse
It Reboots as soon as i connect it.
No time to select Charge Only or Storage
If your phone do not have any other problems when not connected to PC, this may probably be an issue with the drivers. Try the following.
1. Backup your comp.
2. Remove all external connections except power from your PC
3. uninstall all drivers and software related to HTC.
3. Restart PC and give a few minutes
4. Connect the phone
5. Check whether all drivers are getting automatically installed (it should)
OR alternatively try connecting the phone to another PC (should not have any preintalled HTC drivers)
Hope that helps.
bezbeV said:
If your phone do not have any other problems when not connected to PC, this may probably be an issue with the drivers. Try the following.
1. Backup your comp.
2. Remove all external connections except power from your PC
3. uninstall all drivers and software related to HTC.
3. Restart PC and give a few minutes
4. Connect the phone
5. Check whether all drivers are getting automatically installed (it should)
OR alternatively try connecting the phone to another PC (should not have any preintalled HTC drivers)
Hope that helps.
Click to expand...
Click to collapse
I'm also having the same issue , but its not working with me. I tried it on my laptop..
Sent from my HTC One V using Tapatalk 2
seniors pls help
coolnitman said:
I'm also having the same issue , but its not working with me. I tried it on my laptop..
Sent from my HTC One V using Tapatalk 2
Click to expand...
Click to collapse
Hi guys,
I am sorry but I have run out of ideas here. Some senior members please pitch in and help these guys.. I would also advice a hard reset (after backing up everything) but its left to you. Do wait for some guidance from our senior members. May be it has a simple solution :fingers-crossed:
try using the USB cable that came with your phone.....(the one you got plugged into the charger)
Lloir said:
try using the USB cable that came with your phone.....(the one you got plugged into the charger)
Click to expand...
Click to collapse
I was using Original HTC USB only. But now suddenly USB started working fine without a reboot
Hi guys,
I hope you can help me, sorry for my english, I'm from France, I wanted to install cyagenmod 10 but the installation was aborted.
I've relock bootloader to install a RUU but not enough battery, I managed with a lot of issues to unlock the bootloader to recharge my hox but now I can't get to fastboot by usb, the hox is no longer recognized on my pc,when it connected on my pc i can go in fastboot but i can't navigate in, i can't up or down in reboot, boot bootloader... it's blocked.
So i can't flash the recovery to charge the device, I can't do anything, i've clockwork recovery touch 5.8.2.4, i can't charge or mount usb with this recovery.
the big problem is that when I charge it, an hour after the phone turns off, no battery, nothing, is it normal ?
I think it goes up to 3600 mV and discharge but why?
I'm looking for a solution since one week, i don't find.
I've buy this used hox on ebay uk 2 weeks ago, it worked perfectly before manipulation.
Sorry again
Thank you for your help.
Good evening all.
http://forum.xda-developers.com/showthread.php?t=1960253
Use this.
Then flash recovery and Rom of choice!
Sent from my HTC One X using xda premium
Got it in .bat already
http://db.tt/aLqeTpPO
Place the file in the fastboot flash folder, put the phone in the bootloader/fastboot usb mode and execute the .bat file, it will reboot the phone constantly and charge it little by little......
And update to CWM 5.8.4.0, it will charge from there and you can mount sd as usb mass storage.
Ok guyz thanks but the problem is when i plug the hox on comp, it isn't recognized
C:\Users\\Desktop\Fastboot>fastboot getvar battery-voltage
< waiting for device >
I plug the cable, i've Fasboot USB but it's like i've plugged nothing, it's since i've re-unlock bootloader with htc dev.
In first i've unlock boot to install CMD 10, then i've relock to install RUU and now i've re-unlock to charge and fix it the problem.
it's could be a problem with htc drivers or may be the pc ??
Try a different usb port, I don't think the HTC drivers like USB3.
I've tried hundred of times all usb2 ports, i've tried in another pc, i've uninstalled et reinstalled many of times htc sync and sdk but always same result, my hox isn't recognize, impossible to do something, i'm blocked, i've tried everything since 10 days.
Please please need help !!!
Did you try this :
Uninstall HTC sync completely and only install these HTC drivers
http://db.tt/gXVxa3Dp
Solved !
i've tried these drivers and last, yesterday i've change usb cable and it was finally recognized!!
I've flashed recovery and boot, now all works, however i've tried with 2 usb cables, third was good.
thank you very much for your helps guyz, have fun.
Sorted then ! Good. :thumbup:
CASE CLOSED !
Hi......
My PC & my laptop won't recognise my phone despite several failed attempts! No mass storage no fastboot, nothing! not even when i mount it via recovery! Android debugging is checked.
My phone is on CM10.1.3
Pls help!
saleh9416 said:
Hi......
My PC & my laptop won't recognise my phone despite several failed attempts! No mass storage no fastboot, nothing! not even when i mount it via recovery! Android debugging is checked.
My phone is on CM10.1.3
Pls help!
Click to expand...
Click to collapse
When you start in bootloader and choise fastboot and connect the phone what you see in device manager. Are you install latest drivers. Are you try only in Windoes7, try on XP. Are you change the cable maybe is broken.
This with RED letter is important first try change the cable
Thant said:
When you start in bootloader and choise fastboot and connect the phone what you see in device manager. Are you install latest drivers. Are you try only in Windoes7, try on XP. Are you change the cable maybe is broken.
This with RED letter is important first try change the cable
Click to expand...
Click to collapse
"Fastboot usb" but when i try to flash kernel or erase cache it gives me <waiting for device>! i should mention that everything used to work perfectely a while ago!
and yes i've tried with W7 & XP and with different cables, but nothing changed! only charging.
saleh9416 said:
"Fastboot usb" but when i try to flash kernel or erase cache it gives me <waiting for device>! i should mention that everything used to work perfectely a while ago!
and yes i've tried with W7 & XP and with different cables, but nothing changed! only charging.
Click to expand...
Click to collapse
Are you using the stock cable and is the usb port your using a 2.0 port? if not then it wont work or well it might but not stable.
saleh9416 said:
"Fastboot usb" but when i try to flash kernel or erase cache it gives me <waiting for device>! i should mention that everything used to work perfectely a while ago!
and yes i've tried with W7 & XP and with different cables, but nothing changed! only charging.
Click to expand...
Click to collapse
Change the cable first!!!! Are you tried with different cable?
fader910 said:
Are you using the stock cable and is the usb port your using a 2.0 port? if not then it wont work or well it might but not stable.
Click to expand...
Click to collapse
Yes, and i don't think that would make any difference! cause if it was "1.1 port" it would work but slower!
Thant said:
Change the cable first!!!! Are you tried with different cable?
Click to expand...
Click to collapse
I've mentioned that i used different cables! htc/sony/samsung
saleh9416 said:
Yes, and i don't think that would make any difference! cause if it was "1.1 port" it would work but slower!
I've mentioned that i used different cables! htc/sony/samsung
Click to expand...
Click to collapse
then if you have the latest drivers and no working again you have hardware problem with the USB port on your hox,
Thant said:
then if you have the latest drivers and no working again you have hardware problem with the USB port on your hox,
Click to expand...
Click to collapse
I hope not! and the confusing part is the phone charges via the USB port!
Thanks anyway.
saleh9416 said:
I hope not! and the confusing part is the phone charges via the USB port!
Thanks anyway.
Click to expand...
Click to collapse
Yes your power pin 1 and 5 work. your pin 2 Tx(from phone to computer) not work and pin 3 Rx(from Phone to computer)work.And for this you see your device fastboot usb becouse the phone receive from computer and know to go in fastboot usb but when you send command from computer fastboot getvar all the computer wait for response from the phone but your Tx is broken and you see waiting for device.
Please try to run the comand fastboot reboot-bootloader and report back
saleh9416 said:
Hi......
My PC & my laptop won't recognise my phone despite several failed attempts! No mass storage no fastboot, nothing! not even when i mount it via recovery! Android debugging is checked.
My phone is on CM10.1.3
Pls help!
Click to expand...
Click to collapse
hello! I had the same issue recently, so I solved it by next actions: I typed in the Windows command line(cmd.exe) 'pnputils -e', so I could see all drivers I have installed and their 'oem*.inf' files. I had 4 HTC drivers, it was like they were in a conflict. Then I deleted each driver with next command: 'pnputils -f -d <oem file name>.inf'. So after that, I plugged in the cable and the HOX was recognized by the computer!
Report back if that helped you!
Thant said:
Yes your power pin 1 and 5 work. your pin 2 Tx(from phone to computer) not work and pin 3 Rx(from Phone to computer)work.And for this you see your device fastboot usb becouse the phone receive from computer and know to go in fastboot usb but when you send command from computer fastboot getvar all the computer wait for response from the phone but your Tx is broken and you see waiting for device.
Please try to run the comand fastboot reboot-bootloader and report back
Click to expand...
Click to collapse
The same message "waiting for device"
saleh9416 said:
The same message "waiting for device"
Click to expand...
Click to collapse
Try the metod on @Timofey_K
Wich recovery are you using? Try enter from there, mount the Phone as mass storage from recovery
Sent from my HTC One X using xda premium
matitorres07 said:
Wich recovery are you using? Try enter from there, mount the Phone as mass storage from recovery
Sent from my HTC One X using xda premium
Click to expand...
Click to collapse
You really have to read the OP again :sly:
Timofey_K said:
hello! I had the same issue recently, so I solved it by next actions: I typed in the Windows command line(cmd.exe) 'pnputils -e', so I could see all drivers I have installed and their 'oem*.inf' files. I had 4 HTC drivers, it was like they were in a conflict. Then I deleted each driver with next command: 'pnputils -f -d <oem file name>.inf'. So after that, I plugged in the cable and the HOX was recognized by the computer!
Report back if that helped you!
Click to expand...
Click to collapse
Unfortunately it didn't work! I've found only 1 HTC driver & I deleted it anyway, but the issue remains unsolved!
I presume the issue is within my phone! maybe it's a hardware problem as @Thant have said.
Thanks anyway.
i was having a similar (not exactly same) problem that on CM 10.2, my phone storage was not being mounted on my pc but it mounted in recovery and fastboot... this is what i did..
Connect your phone to pc, go to device manager from control panel and see if the device shown with a yellow triangle.
right click it, chose to update driver software, select manually from a list, chose android adb interface from list, then either chose google or htc (depending on your rom, for CM, prefer google).. Your phone will be recognised by pc
Khizar Amin said:
i was having a similar (not exactly same) problem that on CM 10.2, my phone storage was not being mounted on my pc but it mounted in recovery and fastboot... this is what i did..
Connect your phone to pc, go to device manager from control panel and see if the device shown with a yellow triangle.
right click it, chose to update driver software, select manually from a list, chose android adb interface from list, then either chose google or htc (depending on your rom, for CM, prefer google).. Your phone will be recognised by pc
Click to expand...
Click to collapse
The phone isn't shown in device manager!
saleh9416 said:
The phone isn't shown in device manager!
Click to expand...
Click to collapse
Then try using a different data cable... also try connecting it to a different pc and also check if otg usb is working or not.. coz if otg does not work then its a problem with your port