Related
OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.
I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB
Yep, I broke my galaxy. Screen and touch sensor works awesome, but screen is fully shattered. Searching at the forum gave me one positive result: http://forum.xda-developers.com/showpost.php?p=23644712&postcount=6
But i cant find any guide anywhere. If someone know how to make this kind of operation please leave your post or guide, it would be great. Thanks in advance!
Hello,
youtube is your friend
http://www.youtube.com/watch?v=65pvAINg2ME&feature=my_favorites&list=FLhOahoxI-440fS-S2edtp7w
glass only video - hmmm...
exeq said:
Hello,
youtube is your friend
http://www.youtube.com/watch?v=65pvAINg2ME&feature=my_favorites&list=FLhOahoxI-440fS-S2edtp7w
Click to expand...
Click to collapse
the above is for the digitizer w/glass - the below is for glass ONLY
http://www.youtube.com/watch?v=CfuTVjI_Wao
It is very risky to replace the glass only. Doing it this way increases the risk of damaging the AMOLED panel, either by overheating it or scratched/cracked by the broken glass. I've explained it before; if you want to replace the glass only, you'll need to separate the screen assembly from the frame first, then separate the glass from the AMOLED panel. You might end up breaking the panel anyway, so might as well replace the whole thing. But you can give it a go. It should be possible to remove the glass while keeping the AMOLED panel in the frame, because the panel itself is very fragile.
I replaced only the glass on mine.
igor45 said:
the above is for the digitizer w/glass - the below is for glass ONLY
Click to expand...
Click to collapse
Hi. This is my story about SUCCESSFULLY replacing only the glass of s2.
Background, you can skip this:
Few months ago I broken the glass of my beloved S2 in an accident, but because I had a screen protector the pieces of glass were kept together and the phone was 100% usable, only the image was distorted because of broken glass.
So I searched the available options: replace the whole display for a price of more than 100euro. Buy a defect s2 with good screen, but didn't found any lower than the previous price.
I had a previous experience with an Ipod Touch with the same problem, when I ordered the glass from ebay and went to a local phone repair shop that destroyed the Ipod. It was usable before going to that shop.
So I decided to give it a try and try to change it myself. I'm a programmer with what can be called poor electronic and hardware skills. So if I was able to do it, and you were able to find this post, you can replace it too. But after seeing some videos I had more confidence on my skills than of those repair specialists that were not careful with the other device.
First I found a clip on youtube about why you CAN'T change only the glass on S2. But I found also the above video with a interesting method, but it required a Molybdenum string that I couldn't found at a good price. Actually I believe that the shipment to Romania made the price to high for the string.
After researching I found the SOLUTION: on a page or youtube clip about how to remove the broken glass. But I've lost the link. Anyway, the procedure was simple. I remember that the video was about replacing the glass on a Galaxy S3.
So I ordered the replacement glass and some adhesive (finally not used) from ebay.
After I got the replacement parts, I opened the phone, you can find somewhere online the instructions how to do it.
For removal I used a pack of plastic poker card. It's needed something to not be to hard to scratch the digitizer, but hard enough to remove the broken pieces of glass.
I started removing the pieces around the Home button to get a feel of the process, and proceeded to remove all the pieces of glass and glue. It took around 3 hours to finish it and 48 cards. You need to lift the broken pieces with great attention and patience. It's not a hard job, but it takes time. Maybe with a hot gun is easier to remove, but when I received the replacement I was anxious to start and did not wait to procure one. During the whole process I kept the phone started to be sure that I did not broke the screen. In case of possible breakage or of a bad scratch I thought that I don't need to continue the procedure. Maybe is not recommended to keep it running, but it gave me a positive feedback that everything is ok.
After removing all the pieces of glass and glue I was able to see some fine scratches with a black background. I used some dust removing solution and then I attached the new glass. I only fitted the new glass on the place and I believe there were some glue left on edges that keep it in place because I did not added any other glue and it did not moved until now. With the new glass the scratches from the digitizer are not visible at all. And the phone works as new, the touchscreen was not damaged at all.
So it's completely possible to replace it.
Before fitting the new glass the cleaned touchscreen was like the touchscreen on S4: it was only needed to hoover with a finger at some distance above, but not touching . I remember that the replacement of my glass was before the release of S4 and when I found about this feature I knew that I already had something like this on my S2.
I don't remember having any other difficulties during the replacement except the removal of broken glasses. And I used this phone continuously without problems since.
Only last night the phone stopped charging and I had to replace the charging port, flex ribbon; but it was not related to glass replacement.
I don't remember if it was needed to open the phone for glass replacement because I opened it when it broke to inspect it and I opened it also few time since then for various tasks.
The total price of replacement parts was below 10$, with glass, screen protector and adhesive ordered from ebay. I ordered also a case to protect the edges for future dropping and was a smart investment. The pack of cards I had from poker set, but It shouldn't be so expensive.
Success with your replacement.
KAWIN tempered glass screen protector for SAMSUNG GALAXY S2
buffon95 said:
Yep, I broke my galaxy. Screen and touch sensor works awesome, but screen is fully shattered. Searching at the forum gave me one positive result: http://forum.xda-developers.com/showpost.php?p=23644712&postcount=6
But i cant find any guide anywhere. If someone know how to make this kind of operation please leave your post or guide, it would be great. Thanks in advance!
Click to expand...
Click to collapse
KAWIN tempered glass screen protector for SAMSUNG GALAXY S2 top quality with best price !
http://www.xkxfilm.com/en/samsung/40-41.html: :good:laugh:
Don't try this at home kids...
I now back to my desire z after the galaxy screen is toast. JUST the heating alone destroyed it. ... Now gonna buy the LCD/screen assembly and do it right.
Sent from my Desire Z using xda app-developers app
if you are not a technician, I suggest you give it to someone REALLY capable of, what do you mean it is not at all easy and the risk of doing damage is very high.
Otherwise follow the advice that was given to you, buy the whole block
Necro thread, but I agree, it is not worth doing so. In order to be done properly, you need to have a very thin wire to separate the two pieces. Not something i would do myself. Much better to replace the whole assembly instead.
Relevant
test
Hello All,
Just recently dropped my screen for AT&T Samsung Galaxy Note 2. The phone still works but has cracks everyone. I was wondering if anyone has attempted to change just the screen itself, if so, where did you buy the screen from and what tools did you use? Also, what is the metal frame around the phone called and is it possible to get it replaced? Thank you and have a nice day!
wangasore said:
Hello All,
Just recently dropped my screen for AT&T Samsung Galaxy Note 2. The phone still works but has cracks everyone. I was wondering if anyone has attempted to change just the screen itself, if so, where did you buy the screen from and what tools did you use? Also, what is the metal frame around the phone called and is it possible to get it replaced? Thank you and have a nice day!
Click to expand...
Click to collapse
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Nate8315 said:
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Click to expand...
Click to collapse
How hard was it to do a replacement on the screen glass itself? and is it easy to do a bezel replacement?
Nate8315 said:
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Click to expand...
Click to collapse
You replaced the glass for the Note 2? Yes I am just talking about the glass itself. Do you have a link to where you bought the item and any link to videos you used to assist you in replacing the glass? Thank you so much for all your help!
wangasore said:
You replaced the glass for the Note 2? Yes I am just talking about the glass itself. Do you have a link to where you bought the item and any link to videos you used to assist you in replacing the glass? Thank you so much for all your help!
Click to expand...
Click to collapse
I purchased the glass off of ebay, I cant post a link due to not having enough post here, but just search "galaxy note 2 replacement glass"
I looked at a bunch of Galaxy S3 glass replacement videos. just search "s3 glass replacement" on youtube.
It is time consuming, I used a hair dryer to be safe because heat guns get too hot if not careful.
I did get a chance to test if the 11pin still pushed video to a tv with a broken screen (using an MHL adapter). It did not for me. I plugged a phone in with a broken digitizer that the s pen still worked on and would let me make calls from. The phone is still function able, just no picture on the screen (working in the dark with the s-pen). Nothing showed up on the tv screen. I plugged another note 2 in to verify and the other note 2 pushed video just fine.
What's the easiest way to tell if I just need to replace the glass versus the entire digitizer?
Glass replacement
Ok for every thread on the internet the digitizer is NOT part of the glass. The glass is just that......glass. Stop calling it a digitizer these are not iPhones!!!!!! The digitizer is laid on top of the amoled and has a connector that runs under the display and plugs in there with a flip type switch connector. The glass can be removed with heat approx. 160 deg with a heat gun on low and keeping track of the temp with a infrared thermo. I've done this a few times now be careful with white as these tend to break easier than the grey not sure why laminate must be weaker. Takes 45mins to do. You can buy the glass for approx. $25 shipped be careful near the bottom with the button flex they are glued on. You must reuse your speaker trim and button trim also. I have only 1 single question can you buy a replacement digitizer by itself without having to buy the amoled? Anyone know and how much they are please point me to one for the i317m.
Why the are you answering a 3 month old thread?
Op says he dropped his screen...lol
Sent from my SAMSUNG-SGH-I317 using xda premium
Better late than never. ...imho...lol
So I dropped my screen a few months back and the glass cracked. It still worked $100 percent and since the glass wasn't shattered it didn't prevent me from using it. It was only annoying me so i decided to order a new glass and replace the glass. During this replacement I completely ****ed the phone up.
From what I understand there are 3 separate pieces, the LCD, the touchscreen digitizer, and the glass itself. I was supposed to pull the glass apart from the digitizer but instead pulled both up leaving only the lcd behind. In the process I completely shattered both glass and digitizer and severed a ribbon cable.
I couldn't link to an imgur album and the images were too large to attach so i put them in a rar file. As you can see in the pictures my new glass is completely transparent and the old broken one has a tint to it, and an extra layer attached. That was how I came to the conclusion it was the digitizer. I have tried to see if I could just replace the digitizer but all the pictures I've seen don't show the cable that I severed. I have no idea what that cable does, only that it was connected to the tinted portion of the glass.
Important to note is that the phone works. I hear it power on and if i get a notification it plays the sound and vibrates no issue. I just can't SEE anything. Does this mean the LCD is broken too? Or will it only power up when it has the digitizer attached? Is this repairable, if so, how? if not, where did I go wrong?
At this moment I am not due for an upgrade til June, and I don't have more than $100 to spend on a replacement so if I can I'd like to fix this one to both save money and not have to downgrade to a lesser phone.
Brooklyn11218 said:
So I dropped my screen a few months back and the glass cracked. It still worked $100 percent and since the glass wasn't shattered it didn't prevent me from using it. It was only annoying me so i decided to order a new glass and replace the glass. During this replacement I completely ****ed the phone up.
From what I understand there are 3 separate pieces, the LCD, the touchscreen digitizer, and the glass itself. I was supposed to pull the glass apart from the digitizer but instead pulled both up leaving only the lcd behind. In the process I completely shattered both glass and digitizer and severed a ribbon cable.
I couldn't link to an imgur album and the images were too large to attach so i put them in a rar file. As you can see in the pictures my new glass is completely transparent and the old broken one has a tint to it, and an extra layer attached. That was how I came to the conclusion it was the digitizer. I have tried to see if I could just replace the digitizer but all the pictures I've seen don't show the cable that I severed. I have no idea what that cable does, only that it was connected to the tinted portion of the glass.
Important to note is that the phone works. I hear it power on and if i get a notification it plays the sound and vibrates no issue. I just can't SEE anything. Does this mean the LCD is broken too? Or will it only power up when it has the digitizer attached? Is this repairable, if so, how? if not, where did I go wrong?
At this moment I am not due for an upgrade til June, and I don't have more than $100 to spend on a replacement so if I can I'd like to fix this one to both save money and not have to downgrade to a lesser phone.
Click to expand...
Click to collapse
You can buy a replacement screen with a digitizer attached but it will cost over $100 and the way your phone is now it may not be worth doing yourself. You can get a pro install for around $200. You may want to wait for your upgrade then.
avruma said:
You can buy a replacement screen with a digitizer attached but it will cost over $100 and the way your phone is now it may not be worth doing yourself. You can get a pro install for around $200. You may want to wait for your upgrade then.
Click to expand...
Click to collapse
Yeah I was hoping there was a cheap fix but I screwed myself. I ended up buying one off eBay that has a bad charging port for $100. I'm just going to swap the mobo and I should be good to go.
Sucks I had to spend the money, it was a gift from my brother for a birthday tattoo, butit's a learning experience. If I ever try to tackle a glass replacement again I know what NOT to do.