Hi Guys
Here Is The CWM touch With Some Resolution Issues But With Brightness And Working Perfectly
First of all check out that you have all the things required :
1. A Motorola DefyXT535.
2. Must be rooted.
You would require some apps too:
1. Pimp My Rom
2. stericson Busybox
Here Is The Process
Open busybox and Install it.(smart install recommended)
Open Pimp my Rom and add Universal init.d support.
here is the process:
1)Download and Extract The Attached CWM_Touch.zip
2)Then conncet your device to pc select mass storage mode
3)Paste CWM Folder In Your Sdcard(make sure the CWM folder should be like this sdcard/CWM/bootmenu)
4)Then get out of usb storage mode connect device as camera(by dragging notification area u will see connected as select camera mode there)
5)Then press install bootmenu defyxt.bat
6)Follow the onscreen instructions
after seeing
^^^^^^^^^^^^^Made By [email protected]^^^^^^^^^^^^
Press any key to continue . . .
immediately remove the cable form pc
7)your system will be rebooted automatically don't panic
8)When System Is Rebooting And When You See MotorolaM Logo the soft buttons leds will light up.
Be quick enough to press the Volume down(-) button as you see the leds being lighted then You Will Enter Into Bootmenu
9)Then Select Recovery And Then Select Custom Recovery Finished
YOU ARE NOW IN ClockworkMod Recovery v6.0.3.1{Touch}
NJOY FRIENDS:good:
Note:i am not responsible for any damage to your device do it at your own risk
test it and reply the queries
Srika said:
test it and reply the queries
Click to expand...
Click to collapse
Thanks.,
But do not create new threads., U could have updated your [bootmenu] thread, U have already established a set of followers over there !!!!
Actually i have to try it on friends mobile., will reply aftr that !!!!.,
srijithn said:
Thanks.,
But do not create new threads., U could have updated your [bootmenu] thread, U have already established a set of followers over there !!!!
Click to expand...
Click to collapse
i have asked the mod to delete the thread as we have new cwm
Srika said:
Hi Guys
Here Is The CWM touch With Some Resolution Issues But With Brightness And Working Perfectly
First of all check out that you have all the things required :
1. A Motorola DefyXT535.
2. Must be rooted.
You would require some apps too:
1. Pimp My Rom
2. stericson Busybox
Here Is The Process
Open busybox and Install it.(smart install recommended)
Open Pimp my Rom and add Universal init.d support.
here is the process:
1)Download and Extract The Attached CWM_Touch.zip
2)Then conncet your device to pc select mass storage mode
3)Paste CWM Folder In Your Sdcard(make sure the CWM folder should be like this sdcard/CWM/bootmenu)
4)Then get out of usb storage mode connect device as camera(by dragging notification area u will see connected as select camera mode there)
5)Then press install bootmenu defyxt.bat
6)Follow the onscreen instructions
after seeing
^^^^^^^^^^^^^Made By [email protected]^^^^^^^^^^^^
Press any key to continue . . .
immediately remove the cable form pc
7)your system will be rebooted automatically don't panic
8)When System Is Rebooting And When You See MotorolaM Logo the soft buttons leds will light up.
Be quick enough to press the Volume down(-) button as you see the leds being lighted then You Will Enter Into Bootmenu
9)Then Select Recovery And Then Select Custom Recovery Finished
YOU ARE NOW IN ClockworkMod Recovery v6.0.3.1{Touch}
NJOY FRIENDS:good:
Note:i am not responsible for any damage to your device do it at your own risk
Click to expand...
Click to collapse
"(by dragging notification area u will see connected as select camera mode there)"
can't found this option on my xt535...
Hiro27 said:
"(by dragging notification area u will see connected as select camera mode there)"
can't found this option on my xt535...
Click to expand...
Click to collapse
did you connect your phone to PC r not
Srika said:
did you connect your phone to PC r not
Click to expand...
Click to collapse
of course i did... i'm using stock Asia GB 2.3.7
Hiro27 said:
of course i did... i'm using stock Asia GB 2.3.7
Click to expand...
Click to collapse
hi but onething Touch CWM will not work with GB it only works with ICS
some issue
Hi,
i have some issue with it:
ont 4th step ( Then get out of usb storage mode connect device as camera...) when i do this, the installer can't see my device but if i leave the phone on mass storage it looks like to install the custom recovery. BUT i am not able to get into the recovery mod by pressing the - volume key.
Any idea where i made something wrong ?
k1000dubw said:
Hi,
i have some issue with it:
ont 4th step ( Then get out of usb storage mode connect device as camera...) when i do this, the installer can't see my device but if i leave the phone on mass storage it looks like to install the custom recovery. BUT i am not able to get into the recovery mod by pressing the - volume key.
Any idea where i made something wrong ?
Click to expand...
Click to collapse
when you connecting phone in camera mode just wait for some time till the phone drivers load then install the cwm try once
Failed in my first experiment, i thought it's because i didn't remove it imediately after finished, was it?
Thanks for this.
But I can't flash it with your Paradox Ver 1.0.Why?
ferayn said:
Thanks for this.
But I can't flash it with your Paradox Ver 1.0.Why?
Click to expand...
Click to collapse
r u in stock ics? r what?
Hiro27 said:
Failed in my first experiment, i thought it's because i didn't remove it imediately after finished, was it?
Click to expand...
Click to collapse
m8 b chances r there
I've tried to install 3 times, and all failed. twice bootloop, once succeeded but can't enter recovery and suddenly blackscreen in normal boot.
Srika said:
r u in stock ics? r what?
Click to expand...
Click to collapse
No,I'm using your custom rom now.It succeeded in stock ics but failed in your rom.The cmd says OK,but the soft buttons leds don't light up
Why should it removed immediately? The one can't enter recovery mode and blackscreen in system boot, i thought it because the init.d support from Pimp my ROM (this time i use the beta release and i'm not sure with its init.d add options)
Srika said:
r u in stock ics? r what?
Click to expand...
Click to collapse
I have noticed that the notifylight doesn't blink when received a new sms.
Sorry I'm not allowed to reply in your rom thread in dev board now.
ferayn said:
No,I'm using your custom rom now.It succeeded in stock ics but failed in your rom.The cmd says OK,but the soft buttons leds don't light up
Click to expand...
Click to collapse
If u r using my custom rom then the leds will light in d middle of boot animation
i like your rom
i like your rom and i'm waiting for your next rom~
Related
My arc s went into a boot loop after i replace the ICS software buttons (framework-res.apk) using root explorer and forgot to change it's permissions... =(
Is there anyway to enter recovery mode or root explorer using the pc so i can flash the zip or change the permissions there without booting the phone?
Do you have cwm installed? Are you able to access it? Just adb shell into it and chmod the file to the correct permissions, or you could just replace the original.
Sent from my LT18i using XDA
smartarse93 said:
Do you have cwm installed? Are you able to access it? Just adb shell into it and chmod the file to the correct permissions, or you could just replace the original.
Sent from my LT18i using XDA
Click to expand...
Click to collapse
you mean recovery mode? (power plus vol down)
EDITED : I'm not sure did i install CWM... is there anyway to install it through pc? or change permissions through pc?
This thread contains the tutorial for going into CWM without installing it, and I just copy the most important part out
Copied from vaibhavknockout's thread
--------------------------------------------------
2. – Download attachments below titled recoveryARC.img and RootXperia.zip. Thanks to jlmcr87 and his post. Copy and paste the file recoveryARC.img to the fastboot folder (folder containing fastboot.exe). Also, transfer the file RootXperia.zip 'as it is' to your SD card.
3. - Open the fastboot folder. Right click on the folder background while pressing shift key on windows PC. Click "Open command window here".
4. - A black cmd window will open. Type in the following command - "fastboot.exe boot recoveryARC.img".
5. - Switch off your phone, connect to the USB cable while holding the menu button (rightmost of the three buttons on Arc). A blue led should light up (It is an indicator of entering in fastboot mode).
6. - Let the process run. Look at the cmd window. If it says the process is complete, remove the USB cable.
7. - On your phone, a menu should appear. This is Clockworkmod/ CWM recovery menu (more about this in later questions). Use volume down key to go to 'install zip from SD card' and enter by pressing camera button.
-----------------------------------------------------
After going into CWM, flash the zip containing the framework-res.apk to reboot
natural4862 said:
This thread contains the tutorial for going into CWM without installing it, and I just copy the most important part out
Copied from vaibhavknockout's thread
--------------------------------------------------
1. – Flash any desired stock ROM for Xperia Arc (download 2.3.4 update from link given in "1." of previous question - "I am still not ready to unlock my bootloader. So guide me how to perform rooting on my locked Xperia Arc.") using flashtool (read the question - "I am still not ready to unlock my bootloader. So guide me how to perform rooting on my locked Xperia Arc." to know how to flash a stock ROM using flashtool). This step is optional if you want to root your current stock ROM.
2. – Download attachments below titled recoveryARC.img and RootXperia.zip. Thanks to jlmcr87 and his post. Copy and paste the file recoveryARC.img to the fastboot folder (folder containing fastboot.exe). Also, transfer the file RootXperia.zip 'as it is' to your SD card.
3. - Open the fastboot folder. Right click on the folder background while pressing shift key on windows PC. Click "Open command window here".
4. - A black cmd window will open. Type in the following command - "fastboot.exe boot recoveryARC.img".
5. - Switch off your phone, connect to the USB cable while holding the menu button (rightmost of the three buttons on Arc). A blue led should light up (It is an indicator of entering in fastboot mode).
6. - Let the process run. Look at the cmd window. If it says the process is complete, remove the USB cable.
7. - On your phone, a menu should appear. This is Clockworkmod/ CWM recovery menu (more about this in later questions). Use volume down key to go to 'install zip from SD card' and enter by pressing camera button.
-----------------------------------------------------
After going into CWM, flash the zip containing the framework-res.apk to reboot
Click to expand...
Click to collapse
Thanks! but i had already reflash the sony ICS update again on flashtool resetting all the system file which works fine but sadly i have no idea why the ICS software buttons looks kind of mess up on the stock sony launcher...
simplyjustkids said:
Thanks! but i had already reflash the sony ICS update again on flashtool resetting all the system file which works fine but sadly i have no idea why the ICS software buttons looks kind of mess up on the stock sony launcher...
Click to expand...
Click to collapse
What Rom is this? Or from where you got modified framework file with on screen button?
Sent from my LT18i using Tapatalk 2
Heelp please!!!
hii
im trying to get the on screen buttons for my xperia arc ICS but first time it was a pain to compile the framework-res.apk because a % thing. Then i could compile but when replacing the framework-res.apk with the reframe sh, i get a boot loop =S so i have to reflash and so far my phone still alive.
i still want the on screen buttons what do i miss? whats the permission thing? can you help me to make my phone look like the picture you posted?
pield said:
hii
im trying to get the on screen buttons for my xperia arc ICS but first time it was a pain to compile the framework-res.apk because a % thing. Then i could compile but when replacing the framework-res.apk with the reframe sh, i get a boot loop =S so i have to reflash and so far my phone still alive.
i still want the on screen buttons what do i miss? whats the permission thing? can you help me to make my phone look like the picture you posted?
Click to expand...
Click to collapse
Use rashid.fairus zip. That version is working good.
You could remove SystemUI.apk from zip before flash.
I have one home.apk with alligned home dockbar.
Sent from my LT18i using XDA
still help
vr5411 said:
Use rashid.fairus zip. That version is working good.
You could remove SystemUI.apk from zip before flash.
I have one home.apk with alligned home dockbar.
Click to expand...
Click to collapse
sorry but i dont get what you mean. I read lots of tutorials and the compile part is done with apktool and the replace on the phone with adb shell and reframe sh but that way doesnt work it gets boot loop. Searched what you said but nothing on the web =S
pield said:
sorry but i dont get what you mean. I read lots of tutorials and the compile part is done with apktool and the replace on the phone with adb shell and reframe sh but that way doesnt work it gets boot loop. Searched what you said but nothing on the web =S
Click to expand...
Click to collapse
Here, go to this topic in Arc Themes and Apps section and take cwm zip with already prepared framework.
[mod][ics .562]OnScreen Button+ChromeStyle Recent Panel+AOSP Statusbar
You can remove SystemUI from zip before flash if you only want on screen buttons.
Sent from my LT18i using XDA
THAAANX!
vr5411 said:
Here, go to this topic in Arc Themes and Apps section and take cwm zip with already prepared framework.
[mod][ics .562]OnScreen Button+ChromeStyle Recent Panel+AOSP Statusbar
You can remove SystemUI from zip before flash if you only want on screen buttons.
Click to expand...
Click to collapse
THANX A LOT! now i have on screen buttons =D i have a hard night and you make it worth. Think that the problem was the framework-res i made i think it wasnt created on the right way
Having a bootloop problem help...
in a bootloop situation... first i rooted my device.. then i tried to install a custom rom CW9.. But i forgot to wipe the factory data and cache files.. so after installing the rom i went into a bootloop. I cant even enter into the CWM recovery mode.. plzzz help:crying:
pridas123 said:
in a bootloop situation... first i rooted my device.. then i tried to install a custom rom CW9.. But i forgot to wipe the factory data and cache files.. so after installing the rom i went into a bootloop. I cant even enter into the CWM recovery mode.. plzzz help:crying:
Click to expand...
Click to collapse
try with flash tool installing the factory android, or another room that you are sure works on your phone. Maybe its a prob with the room. wiping all is the safest way but if you are sure its just the room you can uncheck the wipe data box and it will work.
hope it helps
Flash the original the factory image ftf file using flash tool. Then start all over again root, cwm, flash rom
Sent from my LT15 using Tapatalk 2
pield said:
try with flash tool installing the factory android, or another room that you are sure works on your phone. Maybe its a prob with the room. wiping all is the safest way but if you are sure its just the room you can uncheck the wipe data box and it will work.
hope it helps
Click to expand...
Click to collapse
whnever I tried to flash it using a flashtool it gives me an error message like " Your phone is not rooted".. and automatically gets disconnected.
---------- Post added at 05:36 PM ---------- Previous post was at 05:17 PM ----------
hashkan said:
Flash the original the factory image ftf file using flash tool. Then start all over again root, cwm, flash rom
Sent from my LT15 using Tapatalk 2
Click to expand...
Click to collapse
whnever I tried to flash it using a flashtool it gives me an error message like " Your phone is not rooted".. and automatically gets disconnected..
Can you give me the link for factory image of LT18i
That should only happen if your bootloader is locked and you tried flashing a custom kernel.
I would just go with pcc and "repair" the phone.
Sent from my LT18i using xda app-developers app
smartarse93 said:
That should only happen if your bootloader is locked and you tried flashing a custom kernel.
I would just go with pcc and "repair" the phone.
Sent from my LT18i using xda app-developers app
Click to expand...
Click to collapse
Thank u i will try this method....
Help i have install a custom rom on my arc s, and now bootloop.
I have not cwm, how can i do?
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Good Job done
Built from source or using web builder?
i cant flash this through sp - tool
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Credits:
I, Me & Myself..
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
while downloading i got the error
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
First Check if the MTK drivers are installed, check it by going tinto the device managers hardware section in my computer
If it is proper then try connecting your phone without the battery inserted
Same problem..
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
i ported this recovery from a ZOPO Z900 Leader chinese android handset...i tried building from source, but i failed at it because of partition style in a18...
For people facing problems flashing it through sp tools, u all can try to flash it using another pc or alternatively view this youtube video -> http://www.youtube.com/watch?v=969xwsUTkSY
ujjwalk308 said:
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
Click to expand...
Click to collapse
Same problem here.
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
vshlkmr said:
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
Click to expand...
Click to collapse
Ok.now waiting for the bugfix.
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
always usb cable error
Connect usb cable & discconet auto & charging mode
this is usb driver ????
great job. im a noob at this so will try after people posting have successfully ported the cwm to their phone
There are two recovery.img files in your attachments. recovery.img and cwmfinal.img. Which one should be used in sp flash tool?
I recently purchased Karbonn a21, can I try this on it?
Sent from my GT-I9300 using xda app-developers app
Thnx bro worked like a charm.
Sent from my Karbonn_A18 using xda app-developers app
fail root
plz send device manager screen shot
Can anyone please upload stock rom of karbonn a18. My device stock at boot animation screen.
Sent from my GT-P1000 using xda premium
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
same problem any help pz
Cwm flashed
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
will you please give CWM for Micromax A90 specification maybe same as A18
here is Specification
Micromax A90
Super Amoled Plus LCD with 262 k
MTK6575 CPU 1 Ghz
512 MB RAM (350 - 400) User available
512 MB ROM ( its not RAM ) for apps
2.5 GB external SD for media file ( Music/Video,,,etc.)
8 Mega Pixel Camera + 0. Mega Pixel Front Camera
Android OS 4.0.3
with Rooted cell
plz help us to create new CWM + Custom ROM
also its same specification from some Chinese Brand like Zoppo / Hero / Gionnee / HDC
plz help.
Pritesh.mohan said:
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
Click to expand...
Click to collapse
You could do that before flashing Cwm aswell.. Use rom toolbox.. I did it the day I got this phone
Hello,
I've update my Nokia X in new update official (1.2.4.1 & plateforms 1.2) -> update is ok BUT, when i connected my phone on my PC, drivers are not recognized ... :/ .... so i found with web (fb group )
1- Download this How to root without drivers
2 - Copy UPDATE-SuperSU-v2.01.zip in your SD card or internal memory (folder Download for exemple)
3 - Boot into bootloader :
a) switch off your phone
b) then press power and volum down and when your device vibrates release the power button ONLY (no volum down)
c) after 15second release the volume down and connect your phone on USB (PC)
d) click on recovery.bat (folders download) : a command prompt will open,and after closed or whrite "done" -> disconnect your phone
e) remove battery and reinsert battery
f) boot into recovery (power + volum up) and flash UPDATE-SuperSU-v2.01.zip next reboot ...
.. and now, your device is root ... you can swap memory extern for exemple ... no need USB drivers
(NB : after this operation all OK, but USB drivers no found .. so wait for this ...)
i'll try this one
yoann44 said:
Hello,
I've update my Nokia X in new update official (1.2.4.1 & plateforms 1.2) -> update is ok BUT, when i connected my phone on my PC, drivers are not recognized ... :/ .... so i found with web (fb group )
1- Download this How to root without drivers
2 - Copy UPDATE-SuperSU-v2.01.zip in your SD card or internal memory (folder Download for exemple)
3 - Boot into bootloader :
a) switch off your phone
b) then press power and volum down and when your device vibrates release the power button ONLY (no volum down)
c) after 15second release the volume down and connect your phone on USB (PC)
d) click on recovery.bat (folders download) : a command prompt will open,and after closed or whrite "done" -> disconnect your phone
e) remove battery and reinsert battery
f) boot into recovery (power + volum up) and flash UPDATE-SuperSU-v2.01.zip next reboot ...
.. and now, your device is root ... you can swap memory extern for exemple ... no need USB drivers
(NB : after this operation all OK, but USB drivers no found .. so wait for this ...)
Click to expand...
Click to collapse
Fixed the adb drivers though: http://forum.xda-developers.com/nokia-x/general/fix-updated-adb-drivers-nokia-x-v1-2-4-1-t2835827
Still, nice job.
Dom3616 said:
Fixed the adb drivers though: http://forum.xda-developers.com/nokia-x/general/fix-updated-adb-drivers-nokia-x-v1-2-4-1-t2835827
Still, nice job.
Click to expand...
Click to collapse
when i try to install the .zip file .it say installation aborted?anyone?help please?578
Can't enter to Bootloader mode
yoann44 said:
Hello,
I've update my Nokia X in new update official (1.2.4.1 & plateforms 1.2) -> update is ok BUT, when i connected my phone on my PC, drivers are not recognized ... :/ .... so i found with web (fb group )
1- Download this [....]
2 - Copy UPDATE-SuperSU-v2.01.zip in your SD card or internal memory (folder Download for exemple)
3 - Boot into bootloader :
a) switch off your phone
b) then press power and volum down and when your device vibrates release the power button ONLY (no volum down)
c) after 15second release the volume down and connect your phone on USB (PC)
d) click on recovery.bat (folders download) : a command prompt will open,and after closed or whrite "done" -> disconnect your phone
e) remove battery and reinsert battery
f) boot into recovery (power + volum up) and flash UPDATE-SuperSU-v2.01.zip next reboot ...
.. and now, your device is root ... you can swap memory extern for exemple ... no need USB drivers
(NB : after this operation all OK, but USB drivers no found .. so wait for this ...)
Click to expand...
Click to collapse
I can't enter Bootloader mode.. it just nokia logo only for long time...
cheppimme said:
I can't enter Bootloader mode.. it just nokia logo only for long time...
Click to expand...
Click to collapse
Flash stock rom. You did something wrong.
Sent from my Nokia_X using XDA Free mobile app
I'm confused.
Dom3616 said:
Flash stock rom. You did something wrong.
Click to expand...
Click to collapse
Can you tell me more how to do for details?
cheppimme said:
Can you tell me more how to do for details?
Click to expand...
Click to collapse
Search Nokia X General section.
error
Mr.MadScientist said:
Hello.
Me too.
I can not install your update.
I allocated it into the sd card, I started the recovery, but it gave me out "installation aborted" .
I tried to install the cwm recovery with nokia x manager (with the right drivers and everything as you said), but the process hangs at nokia initial logo , and is necessary to remove the battery (after 60 min) for restart the phone. Nokia flash , however, if I try to install it on windows professional 32 bit ( the only windows I have, because I use linux) , tell "is not an application for 32-bit" .
Thanks for your work.
Click to expand...
Click to collapse
Then goto CWM Recovery Thread for Nokia X and learn how to manually flash it.
The update package won't work on Stock Recovery.
Dom3616 said:
Then goto CWM Recovery Thread for Nokia X and learn how to manually flash it.
The update package won't work on Stock Recovery.
Click to expand...
Click to collapse
I apologize for my error but I had write on the wrong thread.
I have not tried the solution proposed here , I tried the solution proposed in the other thread, with the update 1.2.4.1 .
Unfortunately they were open both and I responded to the wrong one.
I hope you will forgive me and especially yoann44 .
I can not download the package because i think that in my country is impossible to pay . I continue to put the code but says it is wrong.
Nor with safari or google chrome I can finish the procedure.
How can I do?
I don't understand about what are you saying, I think you phone is full brick if you are unable to enter in Bootloader Mod, so check your productcode and discribe you problem
Just Download and Follow the Guide from Below Links if you are able to enter in bootloader mode (Half Brick). Otherwise claim you warranty.
Nokia X Flasher are free by Devs.
Nokia X Offical Rom
selmopn said:
i'll try this one
Click to expand...
Click to collapse
and?
Ok now I tried it but without success.
I have done everything.
However :
1) "done" it never arrived even after half an hour
2 ) I repeated the operation
3 ) at the end everything is back (hopefully) normal without root
For me, this method does not work: installation aborted.
So you are removing some apps from system/app
Sent from my Nokia_X
adeebulrehman said:
So you are removing some apps from system/app
Sent from my Nokia_X
Click to expand...
Click to collapse
Yes, facebook , twitter and one drive .
It can be the cause?
If it is necessary I can do a factory reset ...
I do it?
Mr.MadScientist said:
Yes, facebook , twitter and one drive .
It can be the cause?
If it is necessary I can do a factory reset ...
I do it?
Click to expand...
Click to collapse
You can remove app the apps that you don't need.
[MOD][Flashable] Remove all Bloatware apps from system/app Partition within 2 Seconds
Attached is the flash able zip file read the instruction from above post and edit script file from attached as per you requirement.
I have removed Mix Radio, Music, Store, Launcher, Keyboard and replaced them with Google Ones
adeebulrehman said:
You can remove app the apps that you don't need.
[MOD][Flashable] Remove all Bloatware apps from system/app Partition within 2 Seconds
Attached is the flash able zip file read the instruction from above post and edit script file from attached as per you requirement.
I have removed Mix Radio, Music, Store, Launcher, Keyboard and replaced them with Google Ones
Click to expand...
Click to collapse
Thank you very much! But to be sure I 've done the factory reset and I will use after your precious advice , the apps have been restored , but the process does not work've done the factory reset, the apps have been restored, but the process does not work.
OK Try It, If you need help let me know
yoann44 said:
Hello,
I've update my Nokia X in new update official (1.2.4.1 & plateforms 1.2) -> update is ok BUT, when i connected my phone on my PC, drivers are not recognized ... :/ .... so i found with web (fb group )
1- Download this How to root without drivers
2 - Copy UPDATE-SuperSU-v2.01.zip in your SD card or internal memory (folder Download for exemple)
3 - Boot into bootloader :
a) switch off your phone
b) then press power and volum down and when your device vibrates release the power button ONLY (no volum down)
c) after 15second release the volume down and connect your phone on USB (PC)
d) click on recovery.bat (folders download) : a command prompt will open,and after closed or whrite "done" -> disconnect your phone
e) remove battery and reinsert battery
f) boot into recovery (power + volum up) and flash UPDATE-SuperSU-v2.01.zip next reboot ...
.. and now, your device is root ... you can swap memory extern for exemple ... no need USB drivers
(NB : after this operation all OK, but USB drivers no found .. so wait for this ...)
Click to expand...
Click to collapse
Why it's necessary to pay from software that is free form the autor's site?
The proposed solution isn't working on 1.2.4.1 is there another usefull solution to root?
joaofsantosj said:
Why it's necessary to pay from software that is free form the autor's site?
The proposed solution isn't working on 1.2.4.1 is there another usefull solution to root?
Click to expand...
Click to collapse
pay off? who said he had to pay ??? lol ... my tutorial is functional! anyway, there's no point really, because since then, the problem was corrected in USB drivers, so possibility via toolkit x or nokia manager ^^
Hey guys, I decided to update the thread in hopes of clearing confusion.
Currently I've found two methods of rooting that seem to help people.
Method 1 - E.K IT Services: ekitservices.com currently run by senior member @djerick3 *Not a sponsorship*
Method 2 - CF-Auto Root: Very simple and easy to use, all you need a:
Windows PC (7 - 10)
USB Cable
Step 1 - Download CF-Auto Root for the SM-G920P.
Step 2 - Using either adb (adb reboot download) or hardware keys (turn the device off and hold in Volume Down + Home Button + Power Button once prompted, press Volume Up)
Step 3 - Plug the device into the PC and open the included Odin in the CF-Auto zip
Step 4 - Click the "AP" button and choose the included md5 file
Step 5 - Make sure to check the "Option(s)" tab and make sure only "Auto Reboot" and "F. Reset Time" are checked. Then switch back to the main tab and press start.
Step 6 - Wait as CF-Auto Root will begin to boot and root, note that the process can take while. Upon rebooting you should have the SuperSU app (Note. If its not there, you can find it HERE)
Step 6 - Enjoy
< ----- Optional - TWRP Install ------ >
As of right now, current TWRP releases are not working on marshmallow. Lucky though @ram9200 created a custom version of the tool that should work
Step 1 - Download the TWRP Tar file
Step 2 - Boot back into Odin mode and flash via Odin on your PC (use the "AP" tab once more)
Hope this helps:good: as always though, of you need help feel free to to send me a PM
You stole my thunder bro! :silly:
JoeFCaputo113 said:
You stole my thunder bro! :silly:
Click to expand...
Click to collapse
Lol
going to try this now thanks hopefully i can get back my snaprefs thats all i really care about xD
I must be doing something wrong
when I flash it with odin it says it was successful and reboots to home screen, then when I turn the phone off an turn on with power+home+volup it goes to a blue screen saying its installing an update and then to normal recovery
Neto. said:
when I flash it with odin it says it was successful and reboots to home screen, then when I turn the phone off an turn on with power+home+volup it goes to a blue screen saying its installing an update and then to normal recovery
Click to expand...
Click to collapse
maybe, just maybe u didnt turn on OEM unlock in development setting.
yaibakt said:
maybe, just maybe u didnt turn on OEM unlock in development setting.
Click to expand...
Click to collapse
I did turn on
GalaxyS6Noob said:
going to try this now thanks hopefully i can get back my snaprefs thats all i really care about xD
Click to expand...
Click to collapse
Broooo, I had to get rid of snapprefs bc it was like 5+ versions behind the official snapchat.. Have you gotten it to work??
Saafir said:
Untick auto reboot in Odin. The kernel is overwriting to stock recovery on boot.
Click to expand...
Click to collapse
it worked thanks, I don´t know if i did it right butwhen odin finished I forced the phone off and in the same "movement" entered recovery .
all ok now thanks
1619415 said:
Hey guys, after all the confusion on rooting 6.0.1, I decided to throw together a guide real quick (hope this helps)
To do this, you will need:
TWRP (This is a special version only for the Sprint SM-G920P and is meant to be flashed with Odin)
SuperSU 2.68
Odin
Steps)
1) Boot your device into download/odin mode (adb reboot download) or (while the device is off hold home+power+volume down then you will be taken to a light blueish screen saying "Warning", just press volume up)
2) Once your device is in download/odin mode, plug it into your windows PC and open Odin then in odin, click the "AP" button then find where you downloaded the TWRP .tar and press start
3) After that, your device should reboot into the system, if present use "adb reboot recovery" if you don't have adb, turn the device off and hold home+power+volume up and your should get some red text in the upper left hand corner then you should be brought to TWRP where you can flash SuperSU (to get SuperSU onto your device, you can use TWRP's built in MTP function or use adb, I recommend using adb but TWRP's MTP is also good (to enable MTP, click on the "mount" button then make sure to tap the "Cache","Data" and "System" buttons, if your PC does not detect the device, tap "Disable MTP" then tap "Enable MTP". Then your device should be detected where you can then move SuperSU to your device and flash it,
If you need any help, please feel free to PM me:good:
Click to expand...
Click to collapse
As soon as I get home will try this, thanks a bunch!
I need to get my free Hotspot again, I guess I will have to add a new rom, any suggestions?
valbher said:
As soon as I get home will try this, thanks a bunch!
I need to get my free Hotspot again, I guess I will have to add a new rom, any suggestions?
Click to expand...
Click to collapse
I'm hoping to have TeamSPR ready by Sunday:fingers-crossed:
Help
Same issue here. when recovery is booted. blue update screen then original recovery. OEM is on
---------- Post added at 05:19 AM ---------- Previous post was at 04:39 AM ----------
im getting the blue updateing as well. then goes to original recovery/ OEM is on
unchecked the auto reboot and followed directions and am now rooted. Thanks!
This worked for me! Thank you so much!
A few modifications to the overall guide:
a. Turn on OEM unlock (I forgot to do this first)
2. Turn off auto-boot in ODIN (I needed to do this, as TWRP would not load the first time)
d. Move SuperSU zip folder to phone (same as other methods)
Now just need a good custom ROM...
I unchecked auto-boot in Odin and turned on OEM unlock, but it isn't working. I boot into download mode and apply the TWRP, but it is just stuck in download mode with the white bar at like 99% complete. It doesn't hit 100%. I forced my phone off and then booted into recovery right after and now my recovery mode is a white screen. Not really sure what to do.
Saafir said:
Untick auto reboot in Odin. The kernel is overwriting to stock recovery on boot.
Click to expand...
Click to collapse
You are THE MAN, worked perfect, Untick auto reboot worked!
Roms for 6.0.1?
Saafir said:
Untick auto reboot in Odin. The kernel is overwriting to stock recovery on boot.
Click to expand...
Click to collapse
Any good roms now that I have flashed my phone?
Rooted my Sm-g920r4 us cellular tonight perfectly. Thank you very much. =) happy camper with 6.0.1 root now.
I was curious since it said Sprint only method but assured it rooted my us cellular just fine and everything is working. Rebooted and still have root and working twrp recovery. Thanks again.
1619415 said:
Hey guys, after all the confusion on rooting 6.0.1, I decided to throw together a guide real quick (hope this helps)
To do this, you will need:
TWRP (This is a special version only for the Sprint SM-G920P and is meant to be flashed with Odin)
SuperSU 2.68
Odin
Steps)
1) Boot your device into download/odin mode (adb reboot download) or (while the device is off hold home+power+volume down then you will be taken to a light blueish screen saying "Warning", just press volume up)
2) Once your device is in download/odin mode, plug it into your windows PC and open Odin then in odin, click the "AP" button then find where you downloaded the TWRP .tar and press start
3) After that, your device should reboot into the system, if present use "adb reboot recovery" if you don't have adb, turn the device off and hold home+power+volume up and your should get some red text in the upper left hand corner then you should be brought to TWRP where you can flash SuperSU (to get SuperSU onto your device, you can use TWRP's built in MTP function or use adb, I recommend using adb but TWRP's MTP is also good (to enable MTP, click on the "mount" button then make sure to tap the "Cache","Data" and "System" buttons, if your PC does not detect the device, tap "Disable MTP" then tap "Enable MTP". Then your device should be detected where you can then move SuperSU to your device and flash it,
If you need any help, please feel free to PM me:good:
Click to expand...
Click to collapse
Thank U!!!
Rom download: https://cloud.mail.ru/public/5mxC/FNwvnWc4g
Password for unraring: coolpadJUI2017
Extract it in some folder.
Download only Patch, drivers and twrp install from here : https://drive.google.com/drive/folders/0B5vyMGZJJmcnbVUtT3A2UVFtS2M
Than install coolpad assistant from the very first one it has a lot of chines words and its and .exe fail u cant miss, and coolpad setup from the driver folder. After that go to "C: \ Program Files (x86) \ yulong" and install everything that is installable. After that start phone in fastboot mode which is when turn off phone and connect it to pc with usb cable while holding volume and volume down, after that red LED will blink. Or u can go to fastboot trough twrp recovery and find option bootloader confirm it with volume up and there u are. Start coolpad assistant that u installed, browse init.cpb and click check after that and installation will start, w8 it to finish. After that u need to install twrp which u download, start phone again in fastboot, but now using volume up and volume down option cos u dont have twrp anymore( its because JUI needs another one). start MIflash and browse folder TWRP, click refresh and tap on ur phone, its the only option u cant miss click flash. After it is done go to twrp standardly by pressing power button and volume up. Set english language. Go to install folder and Zip file from patch folder. Of course before that u need to transfer it to ur phone.. This patch is important. If u dont install it, it wont boot second time when u reboot phone.
After that download gapps from here : http://opengapps.org/ arm64, 7.1 and aroma check. Go to twrp install and select gapps click flash, Click "Next" - "Customized installation". Uncheck "Load choices". Select "Include" and tick application u want. After clicking finish Click the Home button, go to "wipe" - "advanced wipe", highlight "Dalvik / ART Cache", "Cache", "Data" and wipe. Click "Restart in OS".
After that go to twrp again, and install this chine bloat remover that u firstly transfered to ur phone (this step is not nescessery but I advise u to do it), to delete unnescessery apps. Unrar ROOT file and transfer superuser and apk file to ur phone. Go to twrp again and install superuser. click go to system and install that apk that u transerfed. ROOT STEP IS ONLY FOR THOSE WHO WANT TO ROOT THEIR PHONE. IF U DONT U DONT NEED THIS. I hope that i helpped someone.
Here is my short reviewe. Defenetly uprade eui to this, better interface, less bugs, less heating issues, still some messages dont come, but its around same as eui, even s7 in a very low rate of times have that issue. Battery optimization is much better too.Who didnt upgrade it, do it as soon as possible, cos of lower heating issues which later do damage to your phone and battery of course.
If anyone need help i am here
Can i falsh on c103 what are bugs??
Could we install magisk? I've tried once and it failed.
reddsmokee said:
Could we install magisk? I've tried once and it failed.
Click to expand...
Click to collapse
Same was for me.. I have this one and everything work the same..
pulkitgohil said:
Can i falsh on c103 what are bugs??
Click to expand...
Click to collapse
Fast charging now works, and about buggs, pretty same as on eui, sometimes messeges doesnt come.. and smart look is at this moment unavailble.. Bugs will be fixed in upcoming updates as u have ota update.. Officialy u can but people say that speaker doesnt work, so i wouldnt suggest to install it, w8 for fixed version.
Speaker working or not ?
when it release ? it from Leeco or Coolpad ??? i read somewhaere about Leeeco die, not support software for their product. And how about Coolpad??
roxcky said:
Speaker working or not ?
Click to expand...
Click to collapse
On c106 perfectly.
md07 said:
when it release ? it from Leeco or Coolpad ??? i read somewhaere about Leeeco die, not support software for their product. And how about Coolpad??
Click to expand...
Click to collapse
thi is coolpads product.. 1 month passed since release.
In c103 speaker works ??????
GPS issue
Just updated my Cool 1 c106 and tried to root but failed (QFIL, MI phone... Connected in fastboot mode, recognized as Qualcomm port) programs can't see the phone (before it worked) also a very important issue for me that can't turn on high accuracy GPS. Anyone facing the same issue or any ideas how to solve? :/
Thanks in advance!
I have bricked my phone using this method. It's not starting ,a red light is blinking when connected to the pc. How can I flash stable rom back on it? I have tried using YGDP but the phone is not connecting to the pc . A message is flashed ' usb device not recognised' whenever I connect. Pls guide and give the link of drivers to connect to the pc.
U couldnt brick it if u did all steps i said.. Try to install drivers from programfiles x86/ yulog and install everything fr there.. Pc should then recognize ur phone.. and then try to flash init.cpb with coolpad assistant
.
---------- Post added at 07:53 PM ---------- Previous post was at 07:49 PM ----------
djpingvin said:
Just updated my Cool 1 c106 and tried to root but failed (QFIL, MI phone... Connected in fastboot mode, recognized as Qualcomm port) programs can't see the phone (before it worked) also a very important issue for me that can't turn on high accuracy GPS. Anyone facing the same issue or any ideas how to solve? :/
Thanks in advance!
Click to expand...
Click to collapse
I dont have that issue. Try to install coolpad driver and to install everyting from the folder yulog which is located in Program files(x86). Then your pc shold recognize it. Also install adb, and qualcom driver. Then root it with superuser, not magisk.
GCam with HDR+
Does anyone have the ported GCam with HDR+ working? With a Sony camera sensor and SD652, it should be compatible with the phone under Nougat, and if it does work I would probably try running this ROM.
Use of attachment files???
What use of attachment files??
Does this work on C103?
Can anyone confirm if this works or not with c103?
skraw07 said:
What use of attachment files??
Click to expand...
Click to collapse
First remove chines apps, and second is to root ur phone if u want.
Hi HARSH9080!
Coul you find any solution ? After I successfully flashed TWRP almost the same...
My Cool1 (C106) is bricked. I only can enter to download mode (pushing volume + and - and power ON phone recognized as 'Qualcomm QDLoader 9008') after I installed JUI 7.1 tried to install TWRP recowery as well but now the phone is rebooting after boot logo and can't enter to recovery (stuck on recovery picture). Could anyone please suggest a method (with correct files) to be able to flas first correct recovery then a stock firmware? (YGDP cant see the phone it stucks on 'Entering download mode' only QFIL seems to work). Thank you very much in advance !
gapps stock
can i use arm64 7.1 stock gapps??
Can I flash this stock to Coolpad Cool Play 6 ? It's almost the same with Coolpad Cool 1...