Develop Bugs

How to Replace your Scratched Galaxy S2 Screen DIY

I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!

thanks for the write up, do you have any more photos of your process?

OMG, it's like watching an autopsy.

Could a better resolution screen or even 3d screen be used/upgraded later on?

Nice to know for something happens, Hope not

Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.

Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.

On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App

wow that is the definition of T H I N !!!!!

Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site

psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.

I wonder how these replacement parts compare to the quality of the original parts.

Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?

psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.

It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.

BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL

Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB

DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.

I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance

buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB

[Q] LCD Replacement???

Hi guys, I got my hands on a MT4G with a broken LCD.
First Q, is it worthy getting a replacement off cheapbay? What other options are there?
Second Q, is it hard to replace it? Is it possible to do it myself?
Thanks for your advise...

I haven't replaced an LCD myself but I am looking to replace a digitizer for my wife's phone.
Someone posted up this link for me in another thread I started.
http://www.ebay.com/itm/FULL-LCD-DI...984?pt=LH_DefaultDomain_0&hash=item2a12834fe0
This should take out the hard part of disassembling the digitizer from the lcd and reattaching and the adhesive itself.
It's the complete the front housing, digitizer AND LCD in one. Already assembled.
I haven't ordered it myself yet but I AM tempted. Especially after watching some of these disassembling videos.
Let me know what you decide and how it worked out.
Just PM me.
Thanks bro and good luck.

Thanks a lot, I will check it out, the adhesive part really has me in doubt.

I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.

allenmehrer said:
I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.
Click to expand...
Click to collapse
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.

nguyendqh said:
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.
Click to expand...
Click to collapse
I have to clean the dirt out between my digitizer and lcd! Can't tell you how annoying that is. Suppose someone could do a better job resealing it... It would be nice if a digitizer/lcd kit came with new adhesive.

http://www.papadigitals.com/advance...uch+4g&sgmid=aa6a532f59b343f82afc0aaa2d55c02d
I saw lcd screen and touch screen digitizer for HTC mytouch 4G there.

I've been taking electronics apart since I was 7 tears old. The MyTouch 4g finally beat me.
There are a lot of really delicate connectors that break easily. Be careful

dr_tracker said:
is it worthy getting a replacement off cheapbay? What other options are there? Second Q, is it hard to replace
Click to expand...
Click to collapse
You'd better to buy non-working phone (maybe from ebay) and make one from two phones. You should have the screwdriver. Easy to replace.

It is not really hard i saw a vid on youtube just search it up super easy actually

I bought a digitizer LCD already together for like 75 and it wasn't too bad to exchange and put this new one in but when I powered the phone the bottom left of the screen didn't work and it impossible to take it back out of the silver bezel without breaking it so I sent it back to get my money and lost the bezel. Its not too hard but be careful take your time and don't pull or yank anything.
Sent from my SGH-T959 using xda premium

I replaced my digitizer. I agree, there are many delicate connectors, but nothing to be afraid of. You should watch the YouTube video over and over. Also, be careful not to push on the bottom buttons while taking it apart. This was the most frustrating thing because they wouldn't sit properly when reassembled. I took it apart 5 times before I forgot to detach the power ribbon and ripped it off! There are motherboards available to fix this, but saving it for another day.
Sent from my HTC Glacier using Tapatalk

That's funny that's the same exact thing I did pulled the power ribbon right out so I just said screw it and just bought a new phone on eBay
Sent from my SGH-T959 using xda premium

Replace Chrome trim on SGS2?

I'm trying to find a source on whether I can replace the trim know my phone since it's been dinged from the previous owner as well as myself.
I've found some the link to the replacement screen thread but it doesn't say if the lcd is part of the top or how to get it out? I've seen some oem housings online but not sure if I can remove my lcd which is fine and put it in the newer housing?
Is there glue or adhesive that holds it in?
Thanks for any help.
Sent from my GT-I9100 using xda app-developers app

You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.

supermult said:
You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.
Click to expand...
Click to collapse
Sorry - but I think we have a misunderstanding. I'm talking about the chrome trim around the entire LCD not the camera.

oh.. honestly i don´t think that the part you described is chrome. Atleast not on my GSII
and the thing i posted is the shiny ring around the headphone plug.

OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.

Nyssa1104 said:
OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.
Click to expand...
Click to collapse
Thanks - that's what I wanted to hear. So it's more effort than I'd like to spend on it. Looks like I'll just move the phone to try something else.

[Q] How to repair a broken screen!?

Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/

http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html

I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-

Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?

Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...

I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.

Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!

litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.

Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.

litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.

prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:

repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.

Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...

That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.

Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?

I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.

There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.

litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?

Screen replacement

Hey I just recently broke my screen and I bought my phone last july. Its not completely broken but its shattered most of the screen and its incredibly annoying. Is there anyway I could get a new phone or get a cheap screen replacement within 30-50$ range? Or should I just go ahead and get a new phone?
Sent from my SGH-I747 using xda premium

Tyler.Boston1 said:
Hey I just recently broke my screen and I bought my phone last july. Its not completely broken but its shattered most of the screen and its incredibly annoying. Is there anyway I could get a new phone or get a cheap screen replacement within 30-50$ range? Or should I just go ahead and get a new phone?
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
If the digitalizer isn't damaged, replacing the glass only is cheap and easy. Look it up :good:

BWolf56 said:
If the digitalizer isn't damaged, replacing the glass only is cheap and easy. Look it up :good:
Click to expand...
Click to collapse
How would I tell if the digitilizer is broken? It may look just like the glass is broken. If I didn't have my screen protector on I'm pretty sure it would fall apart
Sent from my SGH-I747 using xda premium

Tyler.Boston1 said:
How would I tell if the digitilizer is broken? It may look just like the glass is broken. If I didn't have my screen protector on I'm pretty sure it would fall apart
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
If the screen usable? Any color/light bleed? Or color distortion/fading?

BWolf56 said:
If the screen usable? Any color/light bleed? Or color distortion/fading?
Click to expand...
Click to collapse
Oh ok well then its still working
Sent from my SGH-I747 using xda premium

Tyler.Boston1 said:
Oh ok well then its still working
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
Check out this thread for replacing your screen
http://forum.xda-developers.com/showthread.php?t=1945494

I highly recommend against trying to replace just the glass. That is what I tried to do, but the LCD is glued to the digitizer which is glued to the glass. I didn't use enough heat and though I got through the edge tape holding the glass to the frame, I shattered the digitizer and LCD as well as busted through the menu buttons.
If you think you can do it, go for it. Not real tool intensive, but there will be lots of heat and the success rate is probably 50/50.
The next step from that is to replace the whole LCD/DIGITIZER/GLASS. But that will set you back around $200. Same process, but you pretty much scrape the glass, digitizer and LCD from the metal frame. Lots of effort, lots of time, and little pieces of glass flying everywhere.
For about the same price, get the FRAME/LCD/DIGITIZER/GLASS asssembly. It only requires removing a few screws, unhooking a couple of cables, and replacing the hole front end. It can be done with care in about 15 minutes.
If you do that, be sure you get the right model number. If you are on AT&T in the US, you'll need the i747. The i9300 may come up a few bucks less, but it's not compatible. Color doesn't matter - you can change now, if you want.
The biggest disadvantage of removing the glass only is the risk of getting dust inbetween the LCD and the glass front. With the other two methods, the LCD/DIGITIZER/GLASS are already fused together. However, if you pull it off, no one will ever know you messed with it, and the warranty cheat won't be tampered with as it will be with a frame replacement.
According to the other post, you are still 13 months from an upgrade. That means around $450 to replace your S3 and $630 if you want to go the S4. For less than half that, you can get the frame replaced. I might even suggest that once you replace the frame, you spend that $10 to replace the glass and try it without any fear of consequences on the one you remove. If you do it well, you might could sell that assembly for $150-$200.
Good luck!

i9300 screen (no frame) will fit i747 frame
can you advise if a i9300 screen (no frame) will fit i747 frame? Mine is 747, I can see lots of posts on Ebay for screens with both 9300 and 747 compatible. Want to make sure before order.

k2lc said:
can you advise if a i9300 screen (no frame) will fit i747 frame? Mine is 747, I can see lots of posts on Ebay for screens with both 9300 and 747 compatible. Want to make sure before order.
Click to expand...
Click to collapse
Lcd, digitizer, and glass are all identical except color. Once you see the word "frame", the model matters.

I just recently did this successfully. The key is a good source of heat and patience. I used a heat gun and it took me about thirty minutes to do. There are screens you can order that come with the little tools to use. Start heating it slowly and use the tools to take the glass off. Heat it until its relatively easy to get the glass off but do not over heat it! Keep going until all the glass is off. Once its off, apply some sticky tape (or you can use the tape that was already on the phone if you don't destroy it) and it will be good to go. Make sure that you take the protective paper off the glass you ordered.
Should you have any issues feel free to PM me.
Sent from my SAMSUNG-SGH-I747 using xda premium