Need support from Virgin Mobile, want to return to stock - HTC One V

I have an issue where everything works fine on my rooted Stock ROM except the 3g.
Previously I had rooted this device (before I activated), kept everything stock except I wanted to be able to make backups with TWRP and to run Adaway so I didnt have ads everywhere. Everything was working fine on my wifi connection.
My older LG phone started having battery issues so I decided it was time to switch to the rooted HTC One V. Activated it, all seemed fine (phone works and wifi works) then I discovered the 3g is intermittent. I suspect there is something wrong at VM with my account because when I bought the next month's service after swapping phones on their site it remained at the old rate of $25. (should have gone up to $35).
This seemed great until i realized my 3g only seems to work 30% of the time, so I put in a support ticket and waiting on a return email or call.
ANYHOW, I'm guessing I'd be better off if I returned this phone to its original unrooted state before I deal with support. Is it as simple as relocking the bootloader then running the RUU on it?
In other words:
1. `fastboot oem lock`
2. Run the RUU
3. I'm good to go?
Or is there more?
TIA

To return to stock yeah that works. Bootloader will say relocked instead of locked though so that may cause some trouble with support but this is the closest you'll get to the state your phone was in when you received it.
Sent from my One V using xda premium

You will also need to reflash the original stock recovery. I attached it for you (pulled from the RUU).

riggerman0421 said:
You will also need to reflash the original stock recovery. I attached it for you (pulled from the RUU).
Click to expand...
Click to collapse
Ugh... It's not flashed when the RUU is run? I did have TWRP on there.
So far I:
-re-locked
-ran RUU
-booted into stock ROM.
So now I go into fastboot and:
fastboot flash recovery recovery_signed.img ??
HTC is confusing compared to my LG phone and my Kindle Fire Tablet Pardon my ignorance!

I think I resolved the issue myself, the email VM finally sent basically had me shut off wifi and run the stock diags for the 3g connection, which seemed to work about 20-30% of the time. It then had me manually do the ##847446# re-program which seemed to do nothing. it turned out it was all a waste and a silly SNAFU.
The errors I would get intermittently were:
Data Call Failure - Error Code 104
Data Call Failure - Error Code 129
Data Call Failure - Error Code 67
Mostly 104.
How did it get fixed? Well, it's now running 3g steadily for 30 minutes 6 hours now, before it was a minute tops before failure.
Apparently, I left the phone I had swapped out running, planning to use it around the house for various boring things. It had the same MSID and MDN obviously, and apparently this was causing conflicts whenever it tried to grab an IP address from Virgin Mobile. I fixed the issue by pulling the battery on the old phone I had swapped from.
Doh!
[edit] edited to verify it actually is fixed this time. So sick of fiddling with everything over the last 2 days.

Related

my desire died out of nowhere... :( please help!, rooted with R5, MCR 3.1 for 2weeks

dear all,
My Telstra branded HTC Desire 8183 died out of nowhere.
Here's what I did:
Rooted with R5
MCR 3.1 ROM (custom kitchen with A2SD+) and r17 froyo rom (mostly MCR3.1)
everything went well, and i was happy with it for 2 weeks (blasting fast HSDPA speed and runs perfectly fine)
i noticed the signal strength was really low two days ago, i thought it was my area having service outage. (called and confirmed) I had my girlfriend's Nexus One AT&T version side by side she's getting full bars.
now the phone will show Emergency Call Only all the time, sometimes even with signal, i wont be able to use the data connection (it's show H, but cant even load google.com with the browser)
Diagnostics that i had done:
unroot with generic WWE rom with goldcard (since the telstra rom that people posted on here have 0.75 bootloader and mine is 0.8 so i can only use 1.21 generic WWE rom)
root again with R5 method
update radio
install MCR 3.1 again
replaced my sim card at AT&T store just to make sure
called AT&T to inquire about service outage
none of them works, now i'm stuck with a phone that doesnt make phone calls and data connection.
did i do anything wrong that mess up the radio of the phone? are these rooting guide and custom rom don't support 8183?
please help me! i really like this phone and it's such a waste to let it sit there
best regards,
ted
The emergency calls only thing is usually associated with a sim problem - like invalid sim, unactivated sim etc.
Have you paid your account?
thanks for the advise
yes i did...same thing happened, sometimes when i get signal, i cant seem to use data connection...cant even make phone calls...if im lucky i can make 1 out of 10 times..
i suspected the sim card problem, that's why i went to AT&T store for a replacement.
Solved
I had the same problem, I also have the A8183
To solve it, I went fastboot mode with USB plugged.
then on Android SDK, I did :
./fastboot-mac enableqxdm 0
./fastboot-mac oem boot
just fastboot for pc
and the phone reboot, turn it off and insert your SIM.
I knew it was fix first boot because sdcard was now mountable.
Then SIM was recognized.
But then I have USB problem in recovery, I think I'll need to flash the misc partition.
blauze said:
I had the same problem, I also have the A8183
To solve it, I went fastboot mode with USB plugged.
then on Android SDK, I did :
./fastboot-mac enableqxdm 0
./fastboot-mac oem boot
just fastboot for pc
and the phone reboot, turn it off and insert your SIM.
I knew it was fix first boot because sdcard was now mountable.
Then SIM was recognized.
But then I have USB problem in recovery, I think I'll need to flash the misc partition.
Click to expand...
Click to collapse
What you are describing is the fix for the usb brick issue. This is not the problem here.
To me this sounds like a faulty handset, as all the software fix options seem to have been done. I'm no expert though!
what is fastboot-mac
im using windows xp with androidsdk tools
i have fastboot command...how do i type that?
socktug said:
What you are describing is the fix for the usb brick issue. This is not the problem here.
To me this sounds like a faulty handset, as all the software fix options seem to have been done. I'm no expert though!
Click to expand...
Click to collapse
is it really? i got my hopes up for a second...i really wanna get this thing fixed...
teddyonair said:
is it really? i got my hopes up for a second...i really wanna get this thing fixed...
Click to expand...
Click to collapse
You can give the commands a go, but I doubt they will help with this. Have a look at the threads on usb brick.
socktug said:
You can give the commands a go, but I doubt they will help with this. Have a look at the threads on usb brick.
Click to expand...
Click to collapse
tried the first command, it says "waiting for device"...no response from phone and command prompt at all
hey guys, keep the opinions coming...thanks in advance!
Try flashing to a different compatible radio version as the version you currently have may be causing the poor reception/signal strength issues.
-------------------------------------
Sent via the XDA Tapatalk App
MasDroid said:
Try flashing to a different compatible radio version as the version you currently have may be causing the poor reception/signal strength issues.
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
i did tried 3 different radio...its not just signal being weak...kept on showing X and whenever i tried to use the data connection when H shows up, it will just stuck there when loading google.com in browser.
teddyonair said:
thanks for the advise
yes i did...same thing happened, sometimes when i get signal, i cant seem to use data connection...cant even make phone calls...if im lucky i can make 1 out of 10 times..
i suspected the sim card problem, that's why i went to AT&T store for a replacement.
Click to expand...
Click to collapse
Hmmmm - the rooting process does not affect the A8183 - cos that's what I've got and it works fine. Maybe try and flash the Telstra ROM? That's the one that would have come with the phone in the first place. Who knows, that might reset something? Probably a long shot but you sound desperate!
You can get that ROM in the ROM sticky in this topic.
Now i have 0.80 bootloader it wont let me install the telstra rom since bootloader version being different (0.75)
any idea how i can override that?
After the rooting process when i first got the phone everything was working fine til two days ago
teddyonair said:
Now i have 0.80 bootloader it wont let me install the telstra rom since bootloader version being different (0.75)
any idea how i can override that?
After the rooting process when i first got the phone everything was working fine til two days ago
Click to expand...
Click to collapse
you could try this: http://android.modaco.com/content/h...-com/310186/mcr-telstra-8183-mod-version-3-5/
I think that will work with 0.80 bootloader.
I guess it's not easy to take the device for repair as I'm tippin you got it through eBay or similar, and HTC in the US probably won't support the warranty.
I believe that i had sort of the same issue as you are describing, sometimes my 3G connection died, and there was nothing i could do too get it back, and it sometimes failed to make a connection when i tried to make calls with full coverage.
I don't know how i got the problem, because the phone has been fine since i rooted it 1 week ago.
I decided to go back to the latest radio update I had before I rooted, and now it works fine again.
I used 32.34.00.28U_4.05.00.30_2 from the stock HTC radios thread. (new users not able to post links)
Hope this solves your issue as well, I have an unbraded Desire A8181.
JoakimCarli said:
I believe that i had sort of the same issue as you are describing, sometimes my 3G connection died, and there was nothing i could do too get it back, and it sometimes failed to make a connection when i tried to make calls with full coverage.
I don't know how i got the problem, because the phone has been fine since i rooted it 1 week ago.
I decided to go back to the latest radio update I had before I rooted, and now it works fine again.
I used 32.34.00.28U_4.05.00.30_2 from the stock HTC radios thread. (new users not able to post links)
Hope this solves your issue as well, I have an unbraded Desire A8181.
Click to expand...
Click to collapse
im going to give the radio you mentioned a try...would u mind telling me where are you located and what network provider are you with?
Tried that radio already now it shows signal but the behaviors are the same, feels like its trying to establish connection but got stuck on upload (not sure if thats the case since only the up arrow stay lit but not the other one)
@teddyonair: did u drop down ur mobile by any chance ??? might be some hardware disconnection inside is giving u this trouble i guess.... otherwise with so many software reflashing & modding,ur mobile should have been working by now....
u better get a professional help either from the htc or from someone who deals with htc repairs.... this is my sincere advice if u wish to listen to me.... hope u have not screwed up ur mobile.... might be a hardware problem... just try this once... ok ????
i've managed to unroot the phone with telstra shipped rom. phone has been acting the same way.
so im not sure if it's the hardware issue. anybody has experience how to send the phone back to Telstra Australia for repair?
thanks!
It sounds to me like you may have a faulty antenna in your phone

[Q] WiFi Not Working after Unlock and Root

I have a PrimoC phone that I unlocked and rooted then I installed TWRP and made a backup. I did not bother connecting to WiFi before doing this, but the phone was showing that it wwas receiving signal from VM. After installing TWRP with Hasoon2000's AIO and making a backup, I went to Settings so I could connect to WiFi and download MSL reader. WiFi is on, but the phone can't find any networks and it is no longer connecting to VM.
Any ideas what's wrong?
Phone is Primo C, CDMA
flash boot. img in bootloader via cmd...
Sent from my HTC One V
Where can I get that for the stock ROM? I've flashed the boot.img of custom ROMs on other phones, but not stock.
Open up the ROM zip from a stock ROM and pull out the boot.IMG. I'm sure there's some rooted stock ROMs posted in your dev section. Or from a nandroid backup from a stock ROM, if you have one.
Sent from my EVO using xda premium
So would this work?
http://forum.xda-developers.com/showthread.php?t=1754036
or the Sprint one here?
http://www.filefactory.com/f/0eafb9c43276c308/
Alright, I flashed the boot.img, but it didn't make a difference. Still no WiFi or connection to VM.
Flashed boot.img a couple of times and rebooted a couple of times. No WiFi or service. What can I do?
Hi, maybe your device has lost It's IMEI. Would you mind posting the first 4 numbers of your imei found in about phone? Thanks.
Sent from my awesome HTC One V using Tapatalk 2
I don't see an IMEI anywhere... Do you mean IMSI? If so, first 4 digits are 3100
Thanks for the help, I really appreciate it. I ported my number to P+, so I don't have a working phone until I get this to work. I flashed another one of these HTC One Vs last weekend without this problem, so I'm not sure how I ran into it this time...
I recommend using SickKernel for Sense roms. Did you flash a kernel through fastboot yet? And did you flash any module files?
No I didn't flash a kernel through fastboot, nor did I on another HTC One V that worked fine last weekend.
I unlocked the phone with this:
http://forum.xda-developers.com/showthread.php?t=1598964
rooted with this:
http://forum.xda-developers.com/showthread.php?t=1751004
Then I installed TWRP and perm rooted by following Hassoon2000's guide and while using his AIO.
This is the same process I followed last week and it worked fine then. The only difference I can think of this time was I didn't even attempt to connect to WiFi before starting this process.
Thanks for the help.
Someone on another forum gave me a .zip called "Jmz-PrimoC-kernel-ICS-20120820". I flashed the boot.img from it and now the phone boots to the VM loading screen and then turns off and continuously reboots and the process repeats.
EDIT: I flashed the .zip and still have the same problem. I'm wiping the cache, dalvick cache, and doing a factory reset and then restoring a backup.
EDIT 2: Restored the backup, it loaded up the phone normally without the reboot this time. I unlocked the phone and a second later it powered off again and now it's rebooting continuously, but it makes it to the normal screen now before doing so.
Really need a phone for work guys. Please help me.
Alright, I did this on a second phone I got for my wife to try and figure out where I went. I unlocked the bootloader and rooted by following these instructions: http://forum.xda-developers.com/showthread.php?t=1598964
WiFi worked after that and VM bars were showing up.
I then booted into Bootloader and opened Hasoon2000's HTC One V AIO Kit. I clicked on TWRP CDMA 2.1.0 and then clicked 'Flash Recovery'. The recovery flashed successfully.
I then made a backup successfully and rebooted. When I rebooted, I was getting 'No Service' and my WiFi doesn't work either.
I may have actually had WiFi and service after I flashed TWRP, but before I made the backup. I think I did, but I'm not sure. Anyways, all that is above is everything I have done with this phone since taking it out of the box. No idea what's wrong.
Please help.
EDIT: When I scan for WiFi on the 2nd phone, I am now finding my network, but strength is always poor or fair and it won't connect.
If the imei really is lost, you will not have a chance but taking it to the HTC service try flashing cwm instead of twrp, maybe that changes something
Sent from my awesome HTC One V using Tapatalk 2
How would I know if the IMEI is lost? I just don't see anywhere it would be in the settings under about phone. Can I just flash CWM over TWRP?
I followed this:
http://www.androidauthority.com/one-v-clockworkmod-recovery-6-0-1-2-custom-recovery-115527/
and flashed CWM.
Still no WiFi or service. I don't need service with this phone, but I do need WiFi.
EDIT:
OK, so I am getting WiFi on the 2nd phone, but it's weak. When I'm right next to my router only the circle fills up on the meter and occasionally one bar will with it. Still no service though.
Hi, well I do not know the exact noun for this, but you can see it at settings, about phone, phone-identity. Sort for my bad English sometimes, I'm from Germany
Sent from my awesome HTC One V using Tapatalk 2
Under phone identity I only see Phone Name, Model Number, Device Serial Number, MEID, MEID Decimal, Phone Number, and IMSI. No IMEI. I checked a friend's working HTC One V he got on the CM sale too and he doesn't have an IMEI under phone identity and his phone works fine.
Also, I am now getting WiFi on the 2nd phone, but it's weak. When I'm right next to my router only the circle fills up on the meter and occasionally one bar will with it. Still no service though. When I go up to my room where another HTC One V running AOKP says ~35% signal, this phone drops.
Thanks for helping me.
You do have the back cover on right? Did you root both phones with Hasoons program?
Sent from my HTC One V using xda app-developers app
Strange. I've set the language of my phone to english for testing, and I'm getting this (1st screenshot).
Instead of using About Phone, you could try opening the dialpad and dialing *#06# (star pound zero six pound). Now a text box like in my 2nd screenshot should pop up. Please only tell me the first four digits, because an IMEI is unique and private.
EDIT: zmk76 is right, in the back cover is the antenna built-in, so signal drop without the back cover is normal (I have really heavy signal drops without the back cover)

[Q] Sprint Galaxy Nexus; signal/3G issues

Sprint Galaxy Nexus
4.2.1
Not rooted
I performed a factory reset on my phone yesterday due to it bogging down and being rather slow. I never did a reset after getting the 4.2.1 update so I figured it was a good time. I woke up this morning, putzed around the house, and setup Tasker again. I laid my phone down for ten minutes while I got ready for work. Whenever I tried to wake my phone and nothing happened. I tried a few more times and the screen would not wake up. I pulled the battery, hard reset, reinserted battery and the phone wouldn't turn on. Then, I wiped the contact terminals (on the battery and the phone) and reinserted the battery and the phone booted up. However, since then I have had some major problems.
1. Power button does not always work properly. I have to press it several times to sleep or wake the phone. (Okay, not major, just inconvenient and probably unrelated to the issues below)
2. No data connection whatsoever.
3. In the data usage menu, there is no longer a data toggle switch.
4. Under the Network Mode option, LTE/CDMA produces absolutely no cell signal whatsoever. I have to switch to CDMA only. (WiFi works fine)
5. Toggling airplane mode, as some have suggested, does not cause the phone to connect to mobile data. Another factory reset did not restore mobile data. Rebooting did not restore mobile data.
6. All of these problems are true before and after factory reset. No new problems were created and nothing was exacerbated as a result of performing a factory reset.
I've been from one end of the internet to another looking for solutions to this problem and I have found that many are having a similar issue but toggling airplane mode or rebooting fixes it. Not the case for me. Most also seem to be having this problem after rooting. Again, not the case for me.
Any suggestions? I would prefer to not return the phone. Purchased from Radioshack and the 30-day warranty has expired. This is my second gnex already, as the first one's charging port broke. It took over a week to get this one from another store which graciously shipped it in to my store. There's also the issue of being broke and not really being able to afford another $30 activation fee on top of the deductible for a new phone.
Why not try reflashing the stock image and updating again to 4.2.1?
Beauenheim said:
Why not try reflashing the stock image and updating again to 4.2.1?
Click to expand...
Click to collapse
Wouldn't I have to root first?
nburns1825 said:
Wouldn't I have to root first?
Click to expand...
Click to collapse
Not at all. You'd use Odin . Myself I have very spotty sprint signal in my home. Spoke to a corporate executive and they mailed me an AirRave free . Never have less then full bars 3g all around home. You should a- flash to stock using Odin following posts in sprint sextjon . b - call up and try to get an airavana.
Sent from my Galaxy Nexus using Tapatalk 2
n0ve said:
Not at all. You'd use Odin . Myself I have very spotty sprint signal in my home. Spoke to a corporate executive and they mailed me an AirRave free . Never have less then full bars 3g all around home. You should a- flash to stock using Odin following posts in sprint sextjon . b - call up and try to get an airavana.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
Excellent. I will give it a shot at some point today or tomorrow and then let you know how it worked out. Thanks!
So, I restored the phone to stock. Signal is still non-existent on LTE/CDMA mode. Cannot perform Profile or PRL updates. Still no mobile data. I'm guessing hardware failure?
Also, on setup it asks for a SIM card. And at the bottom of the drop-down menu, it says "No SIM card|Sprint" or "No SIM card|No Service" depending on if I am in CDMA or LTE/CDMA.
Also, in the Status menu:
My phone number
Unknown
MIN
Unknown
PRL Version
Unknown
ICCID
Unknown
Seems a little odd to me.
Attempted fully rooting and flashing radios. No luck there either. It's also not wanting to update. Tells me my phone is up-to-date (connected via WiFi). Downloading Cyanogen now to see if it will work in the morning.
And while attempting to flash a new ROM, got the famous "can't copy anything to the device ever, under any circumstances" error.
Update: Got CM10 installed. Still "No SIM" error, no 3G, no data, no LTE. Found some more information on this No SIM error. Apparently a few others have had this same problem and in the end had to get a new phone.
Anyone know anything?
You should a- flash to stock using Odin following posts in sprint sextjon
I've been back to stock twice now. The first thing I did was flash to stock. Then I played around a bit and now I'm back to stock again.
Is there a difference between using Odin and Nexus Root Toolkit to return to stock?
Bump
Wow, one day and my thread is buried!
After battling for about a day, I got updated to JB 4.2.1, I can do profile and PRL updates again, but there is still no 3G/mobile data, and I still have zero bars on LTE/CDMA and have to use just CDMA. I am currently stock but the bootloader is unlocked, no root.
If anyone has heard any solution, please help. Also, if there's a difference between flashing to stock with Odin vs NRT, please say so.
nburns1825 said:
Wow, one day and my thread is buried!
After battling for about a day, I got updated to JB 4.2.1, I can do profile and PRL updates again, but there is still no 3G/mobile data, and I still have zero bars on LTE/CDMA and have to use just CDMA. I am currently stock but the bootloader is unlocked, no root.
If anyone has heard any solution, please help. Also, if there's a difference between flashing to stock with Odin vs NRT, please say so.
Click to expand...
Click to collapse
Try fastboot flashing your LTE and CDMA radios again. As far as I know, fastboot commands do NOT require root. I had a similar issue.
Edit: link to post with directions http://forum.xda-developers.com/showthread.php?p=39446679
Sent from my R2-D2 unit on the far side of the moon
Indeed, fastboot does not require root. I've flashed my radios several times now in various different ways. I even flashed different versions. I attempted again but with no luck. I have normal service when using CDMA but nothing on LTE/CDMA. Still no data, still "No SIM card" error.
Pretty sure I'll have to get it replaced. I've gone from stock JB back to stock ICS, rooted, CM10, back to stock ICS, rooted, back to stock JB unrooted, and flashed three different radios. I'm surprised I haven't managed to brick it yet.
UPDATE: Sprint is sending me a new phone, for free.

[Q] Lost IMEI now stuck in boot loop after ODIN to stock

Hello,
I'm having a lot of difficulty getting my Note II (SGH T889V) in working order . I'll try to explain the situation in an organized way. Thank you for your time and kind help!
Background
I have a Note 2 from Wind Mobile in Canada - SGH T889V. I got it 2.5 months ago. It was rooted, was running TWRP and I only loaded one ROM, flashed once, on it - 4.1.2 modified touchwiz ROM. Never once had an issue. The ROM was super stable and in great working order.
I got it unlocked about 2 weeks ago because I was visiting the states. When I got to the states, I put in a T-Mobile sim card which was working great for a few days. One afternoon during my vacation I was having slow data issues, so I thought to change the modem/radio from a Wind Mobile radio to a T-Mobile radio. That gave me 4G data speeds but killed my calls. So I tried to go back to the Wind Radio and that had my phone complaining that there was no SIM card. I went back to the T-Mobile radio and I got calling back but only 2G data.
My IMEI was corrupted - it showed up as zero. I left the T-Mobile radio on the phone when I got back. My home network wouldn't recognize me and thought I was still roaming.
Attempted Fixes
Tried a basic factory reset. Tried a different ROM. Tried wiping all internal data.
I got home and tried to flash to stock ROMs found on XDA for Wind Mobile phones. That didn't solve the issue. The IMEI remained null. The phone would reboot automatically every few minutes unless I turned Airplane Mode on. I figure the phone was looking for a signal and couldn't because of the IMEI problem.
So I looked around on the net and found a link about injecting the IMEI back using QPST (http://forum.xda-developers.com/showthread.php?t=1206275) but I couldn't get the program to detect my phone so I gave up and thought I could just get my binary count to 0 and stock and I'll just take it back for warranty.
I tried Triangle Away but I couldn't get the counter to go to 0 even with stock ROM and recovery. So I thought I would take it to a cell repair shop locally. I took it there and all they did was cause an issue on the phone to make it appear that KIES firmware upgrade failed so that it would be repaired under warranty. You would see a emergency firmware upgrade error the minute you turned the phone on. However, download mode still showed the custom binary count at 1, they didn't get it down to 0.
I spoke with my carrier and with Samsung anonymously, they said the counter would be an issue if I sent it in.
I came back home and tried doing the following, with the hopes of trying Triangle Away again:
1. Installed TWRP via ODIN and ran the restore on the backup I created in TWRP when I first got the phone. I restored everything including EFS. Phone boots to the stock samsung rom but it would restart automatically every few minutes. Even with Airplane mode on, it would still reboot on it's own.
The KIES error message doesn't appear anymore.
2. Went back to ODIN. It was getting stuck on SYSTEM in ODIN version 3.07 when flashing a stock rom. So I switched the USB port on my computer and used ODIN 3.04 then the flashes went through properly with no hang ups.
So I tried to flash a prerooted (http://forum.xda-developers.com/showthread.php?t=1975560&highlight=wind) stock ROM
and
also a basic stock ROM (http://forum.xda-developers.com/showthread.php?t=2061031), along with a stock recovery
Both just get stuck in a bootloop. I tried going to the stock recovery and wiping data, cache, factory reset several times. No luck - still boot loops. Wont go into the ROM.
I did not try "Re-partition" in ODIN. I'm not sure if that'll hard brick the device but maybe that way I can repair all of the partitions? - http://forum.xda-developers.com/showthread.php?t=860432&page=2
__________
Im hoping to get back into a prerooted ROM or stock ROM to try this Triangle Away Method - http://forum.xda-developers.com/showthread.php?t=2272966 to get the custom binary down to zero.
I tried to use the Triangle Away ODIN method but it doesnt go through in ODIN, it just gets stuck.
If I can get into the ROM without it boot looping or rebooting automatically- I think I can fix my IMEI like this person did - http://forum.xda-developers.com/showthread.php?t=2145967
Outcomes Im hoping for
To stop the bootlooping/ automatic reboots, then
1. To get the custom Binary count to 0 so I can send it back in for warranty to Samsung or my carrier, Wind Mobile. The binary says Samsung Official. - http://forum.xda-developers.com/showthread.php?t=2068156
or
2. To get the phone to working order so I can try this persons method - http://forum.xda-developers.com/showthread.php?t=2145967
The phone is still responding and it's still working with ODIN. It makes me think the issue is software or partition related and not hardware related per se. If it is hardware, I just want to get this phone back to Samsung but I need to unroot/clear the binary counter.
The phone has never been dropped or damaged physically. I've really babied the phone. This is my third Samsung Galaxy phone (I've had a Vibrant and S2x before this one.)
This has really ruined my week. I need my phone for work. I greatly appreciate any kind help or guidance. I know the collective genius here at XDA will be able to find a solution.
Thank you so much!
If you have flashed the tmobile modem you will now have to keep the tmobile one in order to get your phone to boot. Flashing a t889v modem will cause loops. Dont know of any way to get back to t889v modems.
Hey, don't worry, you aren't the first to experience this problem. Many users have reported that the T889V will bootloop with the T889V modem after flashing another modem. Many have also restored IMEI and service to their phones, so there is a solution. I don't have the specifics, but there are many threads about this problem with solutions. I have quickly searched for one and I believe it has everything you need to fix it.
http://forum.xda-developers.com/showthread.php?t=2119074&page=3
Byangmang said:
Hey, don't worry, you aren't the first to experience this problem. Many users have reported that the T889V will bootloop with the T889V modem after flashing another modem. Many have also restored IMEI and service to their phones, so there is a solution. I don't have the specifics, but there are many threads about this problem with solutions. I have quickly searched for one and I believe it has everything you need to fix it.
http://forum.xda-developers.com/showthread.php?t=2119074&page=3
Click to expand...
Click to collapse
Thank you. I'm going to give that a shot. I'll install CWM then install a T889 TMobile Radio to see if it boots.
I'll report back. Fingers crossed.
I had same issue... this is how I fixed it
http://forum.xda-developers.com/showthread.php?t=2274843
sniperess said:
I had same issue... this is how I fixed it
http://forum.xda-developers.com/showthread.php?t=2274843
Click to expand...
Click to collapse
Thank you all!
I got the boot loops to stop by flashing CWM recovery, then flashing a TMobile Radio.
From there, I followed the QPST instructions of installing a QCN file on the phone to reenable the AWS spectrum. Then I used the IMEI creator and NV Writer programs and I was back.
Data seems alright, getting alright speeds on Wind right now. I just found my bluetooth a little hard to hear in the car this morning.
So with this process, I should stick with a Tmobile radio from now on right? If I flash a Wind/ T889V modem it'll boot loop?
Have you guys noticed any signal or performance issues after restoring the phone this way? I'm wondering if it's worth the trouble to get the custom binary counter to clear and return this phone for warranty. Seems to be working for the most part so far.
Thank you so much again! I thought I was going to have to pay $100 to get it JTAGed.
Glad to here your back and running.
I have a t889v using it on telus, and since I am stuck on tmobile modem I get lower phone signal but never loose signal. On a plus I now get lte speeds.
First day back it seems good for the most part.
Only issue I had was Bluetooth in my car would cut out at a high rate of speed (when I was on the highway). It worked really well while I was on local roads but once I hit the highway I couldn't hear the other side at all pretty much. I had to put them on speaker to hear them. They could hear me really well, better than before when I was driving on local roads.
Never occurred in the past. Could it be a radio issue? Signal seemed okay and I was able to continue the conversation over the phone speaker on the highway.
lilroach said:
First day back it seems good for the most part.
Only issue I had was Bluetooth in my car would cut out at a high rate of speed (when I was on the highway). It worked really well while I was on local roads but once I hit the highway I couldn't hear the other side at all pretty much. I had to put them on speaker to hear them. They could hear me really well, better than before when I was driving on local roads.
Never occurred in the past. Could it be a radio issue? Signal seemed okay and I was able to continue the conversation over the phone speaker on the highway.
Click to expand...
Click to collapse
The bluetooth issue doesn't seem to be a problem anymore. Disappeared on it's own.
lilroach said:
The bluetooth issue doesn't seem to be a problem anymore. Disappeared on it's own.
Click to expand...
Click to collapse
I noticed I have serious data issues when the network goes into HSPA+ mode. I get really good data for a minute then it'll cut out totally for like an hour. I tried rebooting, tried battery pulling. It seems the T-Mobile radio doesn't interface well with Wind's HSPA+ . I had full bars but the internet wouldn't load. It was pretty non-functional for most of the day.
It works decently when it's not on HSPA+
Tried switching to a Wind modem, went into boot loops. Went back to T-Mobile radio. Should I try a different T-Mobile radio?
how to fix your T889v if you accidentally overwrite the radio
If you get stuck with no IMEI, in my case, flashed omnirom 4.4.1 t0ltetmo, which uses Tmobile radio... it killed the Wind Mobile radio... restoring form nandroid did not help.
solution:
flash omnirom t0lte (not t0ltetmo) and your problems are gone!
lilroach said:
I noticed I have serious data issues when the network goes into HSPA+ mode. I get really good data for a minute then it'll cut out totally for like an hour. I tried rebooting, tried battery pulling. It seems the T-Mobile radio doesn't interface well with Wind's HSPA+ . I had full bars but the internet wouldn't load. It was pretty non-functional for most of the day.
It works decently when it's not on HSPA+
Tried switching to a Wind modem, went into boot loops. Went back to T-Mobile radio. Should I try a different T-Mobile radio?
Click to expand...
Click to collapse

Keep losing data connection and apn setting access

I picked up a Sprint prepaid HTC 816 recently and decided to flash this rom below
[ROM][UNOFFICIAL][CM12.1][5.1.1][VirginMobileUS][A5][single sim][1/1/2016 security]
That one
It installed great, had everything everything working after I added my Sprint APN settings. The phone still displayed it as Virgin Mobile and only 3g seemed to be working. But I was making and receiving calls, text messages and had mobile data.
Fast forward a couple of hours, I installed a custom theme from the Play store, rebooted and ever since then I lost the ability to pickup a network signal and access my APN settings.
If I re-seat the sim and toggle airplane mode it will pickup a network signal and I can regain apn setting access again but it drops within minutes.
Ive reflashed the rom, wiped everything reflashed again, same thing. Any ideas on what has happened?
Thanks and appreciate your time!
monsai83 said:
I picked up a Sprint prepaid HTC 816 recently and decided to flash this rom below
[ROM][UNOFFICIAL][CM12.1][5.1.1][VirginMobileUS][A5][single sim][1/1/2016 security]
That one
It installed great, had everything everything working after I added my Sprint APN settings. The phone still displayed it as Virgin Mobile and only 3g seemed to be working. But I was making and receiving calls, text messages and had mobile data.
Fast forward a couple of hours, I installed a custom theme from the Play store, rebooted and ever since then I lost the ability to pickup a network signal and access my APN settings.
If I re-seat the sim and toggle airplane mode it will pickup a network signal and I can regain apn setting access again but it drops within minutes.
Ive reflashed the rom, wiped everything reflashed again, same thing. Any ideas on what has happened?
Thanks and appreciate your time!
Click to expand...
Click to collapse
Are these the APN codes you used(poster corrected a mistake in green text)? Looks like there is a different APN for prepaid /postpaid.
http://androidforums.com/threads/working-sprint-prepaid-apn-settings.920752/
I indeed use the apn settings in the green from that post. They were working fine until I had a reboot. Then everything went to ****. It wont even let me access the apn settings and when I can its briefly and then I lose signal and apn access.
monsai83 said:
I indeed use the apn settings in the green from that post. They were working fine until I had a reboot. Then everything went to ****. It wont even let me access the apn settings and when I can its briefly and then I lose signal and apn access.
Click to expand...
Click to collapse
I had an issue with something on my Virgin mobile 816 a5_chl a while back and a member @wxppro was very knowledgeable about APN settings and their intricacies. He had a MVNO 816 at the time with an APN issue and I bet he could help you with this as that was my best suggestion for a fix and it didn't help you.
See if you can direct him here to this forum so that if he can help out the info is here to help others as well. Good luck.
Not sure how much I can help. APN is a tricky business. If your APN settings disappear after some time, it is generally because the cellular network the phone connects to does not match the APN's MCC/MNC numbers. Or it could be the phone is in 3G mode (CDMA EvDo mode).
You can try these things:
Switch network types, from LTE to 3G, wait a minute, and then back to LTE. APNs do not show up in 3G mode. They only show up in LTE (or global) mode.
When you have the APNs show up, check the parameters are correct, you can do a "Restore to default" and then add the new one following that post.
Hope this helps.
I'm having a similar issue as well (except on virgin mobile)
A month ago I flashed squid's version of CM 13 on my phone and everything was fine for a few days, until I completely lost LTE and access to APNs. I reverted to stock and still was unable to get LTE, although I could get a shaky 3g connection if I changed the network mode to CDMA only. I called virgin mobile and they walked me through the troubleshooting steps and eventually determined it was a network outage (even though two desires in my house belonging to other family members had LTE). I called again after they verified that the network was working again and they were still unable to fix the issue.
Recently, a friend upgraded from a desire to a different phone on a different network, and gave me his old phone. I plugged in my sim card and activated this new phone and I got LTE. Figuring everything was good, I decided to flash squid's ROM once again. The same issue happened, I got LTE for a day or two until it cut out service again. No access to APNs, not even any service in stock or on the official build of CM12 with the APN fix (I can't access APNs there either). I'm out of ideas and would appreciate if anyone had any input on my issues.
Techdude154 said:
I'm having a similar issue as well (except on virgin mobile)
A month ago I flashed squid's version of CM 13 on my phone and everything was fine for a few days, until I completely lost LTE and access to APNs. I reverted to stock and still was unable to get LTE, although I could get a shaky 3g connection if I changed the network mode to CDMA only. I called virgin mobile and they walked me through the troubleshooting steps and eventually determined it was a network outage (even though two desires in my house belonging to other family members had LTE). I called again after they verified that the network was working again and they were still unable to fix the issue.
Recently, a friend upgraded from a desire to a different phone on a different network, and gave me his old phone. I plugged in my sim card and activated this new phone and I got LTE. Figuring everything was good, I decided to flash squid's ROM once again. The same issue happened, I got LTE for a day or two until it cut out service again. No access to APNs, not even any service in stock or on the official build of CM12 with the APN fix (I can't access APNs there either). I'm out of ideas and would appreciate if anyone had any input on my issues.
Click to expand...
Click to collapse
I have this same phone a5_chl Virgin Mobile. Did you factory reset your device before flashing back to your stock rom? The other thing is and this is just my opinion not a statement of fact or a knock on the wonderful Bigsupersquid but that 13 CM ROM is nowhere close to being stable enough for me to risk flashing it to my daily driver phone. Just read all the posts and his candid responses. You were basically a beta tester .
I'm not an expert in APN's but if you can't get that fixed your last resort might have to be wiping your system and then flashing or running the executable RUU (rom utility upgrade) file found for our device on HTC/downloads . This is a last resort option and wiping your system will remove your existing firmware so have the correct RUU for your phone downloaded to your computer before attempting a wipe. If it's an exe, which I believe the U.S. Virgin Mobile one is ,you will hook up your phone fully charged in fastboot mode then from your computer run the exe RUU like any other exe executable program and wait. It will reformat all partitions and reinstall pure stock ROM. Hope someone else had an easier fix for your data issues and good luck.
EDIT: you will need your stock recovery flashed back and a relocked bootloader before flashing the RUU but I've read that some have flashed their RUU over a custom recovery with a locked bootloader and it wrote over the custom recovery with the stock recovery. I have never personally tried this just the first way I mentioned and that worked for me.
thoctor said:
I have this same phone a5_chl Virgin Mobile. Did you factory reset your device before flashing back to your stock rom? The other thing is and this is just my opinion not a statement of fact or a knock on the wonderful Supersquid but that 13 CM ROM is nowhere close to being stable enough for me to risk flashing it to my daily driver phone. Just read all the posts and his candid responses. You were basically a beta tester .
I'm not an expert in APN's but if you can't get that fixed your last resort might have to be wiping your system and then flashing or running the executable RUU (rom utility upgrade) file found for our device on HTC/downloads . This is a last resort option and wiping your system will remove your existing firmware so have the correct RUU for your phone downloaded to your computer before attempting a wipe. If it's an exe, which I believe the U.S. Virgin Mobile one is ,you will hook up your phone fully charged in fastboot mode then from your computer run the exe RUU like any other exe executable program and wait. It will reformat all partitions and reinstall pure stock ROM. Hope someone else had an easier fix for your data issues and good luck.
EDIT: you will need your stock recovery flashed back and a relocked bootloader before flashing the RUU but I've read that some have flashed their RUU over a custom recovery with a locked bootloader and it wrote over the custom recovery with the stock recovery. I have never personally tried this just the first way I mentioned and that worked for me.
Click to expand...
Click to collapse
I did try factory resetting and I am on stock after flashing the RUU. It makes no sense as the RUU should have reset everything. That perplexes me the most
Techdude154 said:
I did try factory resetting and I am on stock after flashing the RUU. It makes no sense as the RUU should have reset everything. That perplexes me the most
Click to expand...
Click to collapse
OK then you did get back to stock not from a nandroid backup but from flashing or running exe stock RUU? If that's the case then it replaced everything that might have been changed and your issues shouldn't be related to any APN changes. You also removed and reinserted your sim card as I believe, correct?
EDIT: that perplexes me as well my friend!
Techdude154 said:
I did try factory resetting and I am on stock after flashing the RUU. It makes no sense as the RUU should have reset everything. That perplexes me the most
Click to expand...
Click to collapse
i posted about my lte issues i had for nearly two weeks, running stock just to verify the data service problem wasn't my rom...
i had to install stock recovery, relock bootloader, download the ruu.exe from htc and extract the .img file in Wine, then rename it onto the sdcard and reboot into hboot so it'd flash. neither Wine nor virtualbox xp talk correctly to any of my phones over usb. and i wasn't about to native install Windoze.
factory reset stock didn't fix it, even trying activation, update profile, etc.
i learned i could get 3g data but switching to lte instead of cdma shut down data entirely.
virgin eventually directly escalated me to tier 2 tech support in my last call, they sent a couple service programming pushes to the phone that got my lte back online.
i tried the various service programming menu options repeatedly, with no results but the prl updated once; but the trigger to fix my lte seemed to come from upstream.
i tried various apns, in cm12, cm13, and stock lollipop. rebuilt init_a5.cpp with different mccmnc and adjusted apns. i really tried most tricks in the book plus a few more.
as far as alpha testing goes, at this point I'm just sharing something cool... i always enjoyed flashing latest greatest on my ov way before i was building.
not too many actual logs to really bug report for either rom.
bigsupersquid said:
i posted about my lte issues i had for nearly two weeks, running stock just to verify the data service problem wasn't my rom...
i had to install stock recovery, relock bootloader, download the ruu.exe from htc and extract the .img file in Wine, then rename it onto the sdcard and reboot into hboot so it'd flash. neither Wine nor virtualbox xp talk correctly to any of my phones over usb. and i wasn't about to native install Windoze.
factory reset stock didn't fix it, even trying activation, update profile, etc.
i learned i could get 3g data but switching to lte instead of cdma shut down data entirely.
virgin eventually directly escalated me to tier 2 tech support in my last call, they sent a couple service programming pushes to the phone that got my lte back online.
i tried the various service programming menu options repeatedly, with no results but the prl updated once; but the trigger to fix my lte seemed to come from upstream.
i tried various apns, in cm12, cm13, and stock lollipop. rebuilt init_a5.cpp with different mccmnc and adjusted apns. i really tried most tricks in the book plus a few more.
as far as alpha testing goes, at this point I'm just sharing something cool... i always enjoyed flashing latest greatest on my ov way before i was building.
not too many actual logs to really bug report for either rom.
Click to expand...
Click to collapse
Some of that was over my head but happily not all of it. Basically what your saying is the fix needs to come from the carrier and it's a reset issue on their end not a custom rom issue? By the way I'm a big fan of your work. Hell I might be on one of your older ROMs right now I've flashed so many I forget. Thanks for the education.
thoctor said:
OK then you did get back to stock not from a nandroid backup but from flashing or running exe stock RUU? If that's the case then it replaced everything that might have been changed and your issues shouldn't be related to any APN changes. You also removed and reinserted your sim card as I believe, correct?
EDIT: that perplexes me as well my friend!
Click to expand...
Click to collapse
The first time it happened, I flashed back to stock using the RUU.exe. I tried again but the second time I took out the SIM card before running the program, I still can't get LTE.
bigsupersquid said:
i posted about my lte issues i had for nearly two weeks, running stock just to verify the data service problem wasn't my rom...
i had to install stock recovery, relock bootloader, download the ruu.exe from htc and extract the .img file in Wine, then rename it onto the sdcard and reboot into hboot so it'd flash. neither Wine nor virtualbox xp talk correctly to any of my phones over usb. and i wasn't about to native install Windoze.
factory reset stock didn't fix it, even trying activation, update profile, etc.
i learned i could get 3g data but switching to lte instead of cdma shut down data entirely.
virgin eventually directly escalated me to tier 2 tech support in my last call, they sent a couple service programming pushes to the phone that got my lte back online.
i tried the various service programming menu options repeatedly, with no results but the prl updated once; but the trigger to fix my lte seemed to come from upstream.
i tried various apns, in cm12, cm13, and stock lollipop. rebuilt init_a5.cpp with different mccmnc and adjusted apns. i really tried most tricks in the book plus a few more.
as far as alpha testing goes, at this point I'm just sharing something cool... i always enjoyed flashing latest greatest on my ov way before i was building.
not too many actual logs to really bug report for either rom.
Click to expand...
Click to collapse
It does sound a lot like a carrier/account issue as I managed to kill 2 different 816s. I don't think it's the SIM card itself because I put it into a 3rd phone and got LTE, although since it was someone else's phone, I didn' t bother activating it.
I guess you got lucky with support, I tried talking to them and they tried the same thing with me. Although all I got was excuses saying they're logging a ticket with their "network engineers" and to call back in a few days. This continued on for a few weeks until they determined I needed a new phone, which I was also bounced around for another few weeks (I still don't have it).
I'm just completely lost now. I'm almost certain it's my account and it needs to be reset, but I can't get a tech who can help me. How did you manage to get someone in tier 2?
Techdude154 said:
The first time it happened, I flashed back to stock using the RUU.exe. I tried again but the second time I took out the SIM card before running the program, I still can't get LTE.
This is starting to scare me as well because I'm thinking of going back to stock once Marshmallow gets pushed to our phone to get my beats drivers back and this is making me think twice. Sorry your having so much trouble.
Click to expand...
Click to collapse
thoctor said:
Some of that was over my head but happily not all of it. Basically what your saying is the fix needs to come from the carrier and it's a reset issue on their end not a custom rom issue? By the way I'm a big fan of your work. Hell I might be on one of your older ROMs right now I've flashed so many I forget. Thanks for the education.
Click to expand...
Click to collapse
seemed that way.
i took radio logs before and after it worked, and worked only on 3g, and it looked to me like the sim card responded differently to the ril after things were running right again.
mine might've been a special case, though, it came from ebay with no sim, and virgin had to go to a little effort to get it programmed when i installed the sim initially.
they also claimed for several days that the local Sprint tower was down for lte service.
---------- Post added at 10:37 PM ---------- Previous post was at 10:32 PM ----------
Techdude154 said:
The first time it happened, I flashed back to stock using the RUU.exe. I tried again but the second time I took out the SIM card before running the program, I still can't get LTE.
It does sound a lot like a carrier/account issue as I managed to kill 2 different 816s. I don't think it's the SIM card itself because I put it into a 3rd phone and got LTE, although since it was someone else's phone, I didn' t bother activating it.
I guess you got lucky with support, I tried talking to them and they tried the same thing with me. Although all I got was excuses saying they're logging a ticket with their "network engineers" and to call back in a few days. This continued on for a few weeks until they determined I needed a new phone, which I was also bounced around for another few weeks (I still don't have it).
I'm just completely lost now. I'm almost certain it's my account and it needs to be reset, but I can't get a tech who can help me. How did you manage to get someone in tier 2?
Click to expand...
Click to collapse
tier 2 takes luck, time, many calls, and eventually you learn the answers to all the questions tier 1 outsourced from India asks so you can feed it to them so fast they want to shuffle you along. takes a couple of weeks to over a month to get to tier 2 and sometimes they have to be involved multiple times as well.
I've been dealing with virgin since 2009... replaced only two phones, eventually got the rest of the issues hammered out with persistence.
for a little while, twice, i had direct toll free numbers to American tier two even because my issues were so hard to solve. it didn't take too long for those numbers to be disconnected, though.

Categories

Resources