Develop Bugs

[Q] HELP Plz on how to update to Snap 7.0 for CM6

I really want to try the Snap 7.0 Kernel for CM6 but I need some help before I go and format/delete my SD Card. I dont want to get stuck.
The OP says if you're not comfortable restoring a NAND backup from your pc[ you should not try this. I'm comfortable with doing NAND backup via recovery but i'm not sure about from the PC.
If someone has already installed Snap 7.0 and can help me with any commands I might need during the install that would be awesome. I didnt want to post this in the Snap thread because OP says he's not helping with restore type questions.
Snap Thread below:
http://forum.xda-developers.com/showthread.php?t=733099.
Instructions from the Snap Thread below:
Before you read any further, please do the following:
* 1) Perform a nand backup.
* 2) Copy your nand backup to your PC.
* 3) Use Titanium backup or My Backup Pro to back your apps up and store them on your PC.
If you are not comfortable restoring your phone from a nand backup from your PC, you should probably avoid using the QS kernels. I will not offer support for restore related issues.
Ok, let's get to it:
The cleanest way to install Snapv7 is:
* Flash CM6 8/14 nightly with a complete wipe
* Format your SD Card (as described below)
* Flash Snapv7
You can avoid a wipe with this procedure:
* Install RA Recovery. You can also install RA from the alternate recovery section in ROM Manager.
* Reboot into RA and Parition your SD Card as follows: 0MB Swap, 512MB (or 640MB--whatever you want to use if fine) Ext2. Warning: This will erase your SD card. You have a backup stored on your PC right?
* Toggle USB Mount (on)
* Copy cm6-snapv7.x.zip to your SD Card
* Toggle USB Mount (off)
* Flash cm6-snapv7.x.zip
* Reboot
* After the system boots, you may have to reboot if your icons or widgets do not appear correctly. I've also seen cases where widgets had to be re-added. Tuna informed me during one test, he saw a bunch of FC's that a reboot cured. So if you have any problems on the first boot after a successful flash, just reboot and you should be good to go.
* Congratulations, you're done.
----------------------------------------
I already have my SD card backed up on my PC along with a recent NAND & Titanium Backup. I'm just waiting for some more detailed instructions so that I can pull the trigger. Specifically where it says
* Toggle USB Mount (on)
* Copy cm6-snapv7.x.zip to your SD Card
* Toggle USB Mount (off)"
Is that supposed to be done while in Recovery? Am I supposed to somehow enter a manual command to do this part and then after the phone boots, restore my SD card from my PC?
Sorry for the long post, any help is much appreciated!!

I just did this last night actually went without a hitch. I did a full wipe of my phone, then installed cm6 8-15 nightly(and the new gapps). Let the phone do a reboot until it got to the lockscreen, then just shut down the phone while skipping the set up.
Booted into recovery, partitioned the sd card 0 mb swap and the highest ext2 partition that was under 1GB (i forget what it was)
After that, (I use amon recovery), I connected to usb in recovery, moved the kernel over along with setCPU apk, and flashed the kernel. Let it reboot, installed setCPU and adjusted the values, and set up my accounts.
I just used the 7.0 kernel. Make sure to grab setCPU from the forums here, because as he notes it defaults to 1.15GHz and unless you change it your battery will run down quickly.
Just make sure you have a nandroid backed up to your computer because when you partition the ext2 it formats the whole card. Not sure about the whole recovering from PC, I would imagine if anything goes wrong you should still be able to access the boot loader and put the nandroid back on the sd card.
... to adress the connect usb question, I know that is an option in the amon recovery menu ...

He only mentions recovering from your PC because in tjw beginning of his tuturiol, he tells you to copy the nandroid backup files to your PC. You don't actually use the PC for restoring...
Sent from behind you.

elegantai said:
... to adress the connect usb question, I know that is an option in the amon recovery menu ...
Click to expand...
Click to collapse
This is exactly what I needed. I didnt realize when u enable the USB-MS option in Recovery it lets your SD card be used like the hard drive mode when you're booted. I'm going to go ahead and try this now.
Thanks guys!

[Q] Few questions about flashing custom ROM.

Hi all,
Successfully rooted my Desire today using Unrevoked method.
Since I quite like the Sense UI, I've decided on flashing the "[FroYo Sense] LeeDrOiD V2.3b (17/12 l Official l OC&UV l FAST l STABLE l WWE)" ROM.
My phone software details are as mentioned in the signature.
a. Can I flash Leedroid without upgrading radio, etc?
b. How exactly do I format my SD card in ext3 partition? [Can't find a tutorial/thread to do the same.] --
Also, regarding using gparted in linux, do I directly, say use card reader/connect the phone and format? Since I have a 16GB SD card, I intend to have a 1 GB ext3 partition.
What exactly does "Flash Rom (you may need to toggle signature verifacation)" mean? :-o
and
"# Flash Radio (unless you already have it)"??
I am following the steps/instructions from this link - http://forum.xda-developers.com/showthread.php?t=768703
Thanks in advance.

Radio is fine (don't flash any radio until you really know what you are doing), to toggle signature verification go, in recovery, to 'install zip form sd' there is the option to toggle verification.
How to partition your sd cared with gparted is mentioned enough, do some more searching. There are also some videos on youtube on how to do it. If you have the ability to use a cared reader use it.

TheGhost1233 said:
Radio is fine (don't flash any radio until you really know what you are doing), to toggle signature verification go, in recovery, to 'install zip form sd' there is the option to toggle verification.
How to partition your sd cared with gparted is mentioned enough, do some more searching. There are also some videos on youtube on how to do it. If you have the ability to use a cared reader use it.
Click to expand...
Click to collapse
Thanks!
So, with the radio version I have, I can still flash LeeDroid ROM, right?

cthdesire said:
Thanks!
So, with the radio version I have, I can still flash LeeDroid ROM, right?
Click to expand...
Click to collapse
yes
10char

Although, it is said that flashing the radios recommended by the dev would be better for battery life, but I guess it is quite open to interpretation.
You could also try using Rom Manager (by ClockworkMod) to partition your SD card through your phone. That's what I did. Less hassle (probably?) than using gparted or installing additional software on your PC.

ROM Manager (from the market) is your friend.....
Will allow you to partition an EXT3 (up to 512mb - Im still trying to figure out how to create a 1GB partition) and then will allow you to flash LeeDroid ROM.
ROM Manager is very simple to use. Just copy the ROM (zip) to a folder on your SD card, use ROM Manager to create your EXT3, do a NANDROID backup (!!!), and then flash the ROM.
Best bet is to backup your apps and data first (use Titanium ?).
LeeDroid ROM is great

wilbur-force said:
ROM Manager (from the market) is your friend.....
Will allow you to partition an EXT3 (up to 512mb - Im still trying to figure out how to create a 1GB partition) and then will allow you to flash LeeDroid ROM.
ROM Manager is very simple to use. Just copy the ROM (zip) to a folder on your SD card, use ROM Manager to create your EXT3, do a NANDROID backup (!!!), and then flash the ROM.
Best bet is to backup your apps and data first (use Titanium ?).
LeeDroid ROM is great
Click to expand...
Click to collapse
To easily create your partition up to 1024 MB, you can use an Ubuntu live cd of GParted by either burning it to a cd or boot it from a usb stick: http://www.ubuntu.com/desktop/get-ubuntu/download.
Or, you use it from within Ubuntu (vid: http://www.youtube.com/watch?v=sVK-tJe8pXE&feature=related)
1) Connect your phone to your computer (or use an SD Card adapter...., in this case skip to 4)
2) Pull down the notification bar and mount the phone
3) Start Gparted
4) Gparted will search available drives. (Your phone should show up as a USB drive, and will be something like /dev/sdb1 or /dev/sdc1, etc..)
Warning: double-check you've not selected a hdd by mistake!
5) In the upper right corner, select the correct USB device for your phone. (i.e. check to make sure it is correct size for your SD card)
6) Right click on each partition and select 'unmount'
7) Right click on each partition and select 'delete'
If you know what you are doing, you can re-size the partitions and add a new 2nd partition formatted as ext2/3/4
8) Right click on the big gray bar (should say unallocated x.xx gb) and click 'new'
9) Enter configurations
Free Space preceding = 0
Create as = Primary
New size = [don't touch]
File system = fat32
Free Space Following = 512 (or whatever you want)
10) Click add
11) Right click on the big gray bar (should say unallocated x.xx gb) and click 'new'
12) Enter configurations
Free Space preceding = 0
Create as = Primary
New size = [don't touch]
File system = ext2/3/4 (recommend ext4)
Free Space Following = 0 (or ~32 if you want swap)
Click add
13) Click edit, then 'Apply All Operations' to write changes to disk
14) Quit GParted
15) Unmount your SD Card
16) Reboot your phone
You could also use Amon-Ra custom recovery to do this by flashing it with unrEVOked.

MasDroid said:
To easily create your partition up to 1024 MB, you can use an Ubuntu live cd of GParted by either burning it to a cd or boot it from a usb stick: http://www.ubuntu.com/desktop/get-ubuntu/download.
Or, you use it from within Ubuntu (vid: http://www.youtube.com/watch?v=sVK-tJe8pXE&feature=related)
1) Connect your phone to your computer (or use an SD Card adapter...., in this case skip to 4)
2) Pull down the notification bar and mount the phone
3) Start Gparted
4) Gparted will search available drives. (Your phone should show up as a USB drive, and will be something like /dev/sdb1 or /dev/sdc1, etc..)
Warning: double-check you've not selected a hdd by mistake!
5) In the upper right corner, select the correct USB device for your phone. (i.e. check to make sure it is correct size for your SD card)
6) Right click on each partition and select 'unmount'
7) Right click on each partition and select 'delete'
If you know what you are doing, you can re-size the partitions and add a new 2nd partition formatted as ext2/3/4
8) Right click on the big gray bar (should say unallocated x.xx gb) and click 'new'
9) Enter configurations
Free Space preceding = 0
Create as = Primary
New size = [don't touch]
File system = fat32
Free Space Following = 512 (or whatever you want)
10) Click add
11) Right click on the big gray bar (should say unallocated x.xx gb) and click 'new'
12) Enter configurations
Free Space preceding = 0
Create as = Primary
New size = [don't touch]
File system = ext2/3/4 (recommend ext4)
Free Space Following = 0 (or ~32 if you want swap)
Click add
13) Click edit, then 'Apply All Operations' to write changes to disk
14) Quit GParted
15) Unmount your SD Card
16) Reboot your phone
You could also use Amon-Ra custom recovery to do this by flashing it with unrEVOked.
Click to expand...
Click to collapse
cheers
its the Linux bit that scares me I work in IT but have never touched a LINUX OS so im a bit daunted

Hi, if you have win7 use arcronis disc director home, its the easyest way, i did so, and i'm a non it
I have now 1.5gb of ext3, and it works very fine.
-------------------------------------
Sent via the XDA Tapatalk App

malaivica said:
Hi, if you have win7 use arcronis disc director home, its the easyest way, i did so, and i'm a non it
I have now 1.5gb of ext3, and it works very fine.
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
does the demo version allow this ? otherwise it seems to be £35

wilbur-force said:
does the demo version allow this ? otherwise it seems to be £35
Click to expand...
Click to collapse
It is very easy to follow the instructions posted above, I even linked a YouTube video for you and gave you a link on how to create the live cd. You should be fine, give it a go
You won't believe how easy it is... its just because you are unfamiliar with the OS platform.
If you are really struggling, then try this method but be careful as you will be connecting via USB to the PC and executing an automated script (batch file). While the batch file i running, do not disconnect the USB cable while in recovery mode:
1. Turn on your phone while holding the volume down button.
2. You will see HBOOT on the screen.
3. Use the volume buttons to move up and down and power button to select the RECOVERY option.
4. You will now see a red triangle on the screen, at this point plug your phone into your PC via your microUSB cable.
5. Wait for 10-15 seconds and then double click on recovery-windows.bat inside the pushfiles_windows.zip folder you unzipped as part of the root process. pushfiles_windows.zip
6. Using the optical trackpad select Partition sdcard > Partition SD
7. Select SWAP=0, EXT2=1024 and allow the rest to be FAT32.
8. Select the SD:ext2 to ext3 option in this menu.
9. Go back to the Recovery Console main menu and select Reboot system now. While rebooting, unplug the Desire from the USB port.
Windows Pushfiles attached below for you.

Thank you all! And MasDroid, thanks for the detailed instructions. I do have Ubuntu on my desktop. Tried formatting on a spare SD card using GParted and seems to be just the perfect thing. I'll do some more reading before flashing the phone. I do have some more doubts. Wanna make sure that I know what am doing.

@ wilbur-force
Dont know, a friend of mine gave my arcronis, think it was the full version. G-parted did not find my cardreader. And the 512mb whit rom manager was not enough space for me. Sorry for my bad english...
Its my 3rd language
-------------------------------------
Sent via the XDA Tapatalk App

Are the following steps in order and correct (to flash LeeDroid ROM)?
a. Create Nandroid and Titanium backup of the phone.
b. Copy the contents of SD card to a folder onto the PC.
c. Format the SD card with FAT32 and ext3 partition (A2SD+)
d. Copy the LeeDrOiD_V2.3b_A2SD ZIP folder to the SD card (root)
e. Insert the SD card to the phone and boot into recovery
Doubt here: Do I need to 'Wipe Data / Factory Reset' again??
f. Install zip from SD Card.
g. Choose zip from SD Card.
h. Reboot System Now.
Are these steps correct?
Also, after flashing how do I restore the Nandroid/Titanium backup? Do I have to copy the contents (step b) back to the phone and boot into recover and "restore" using Clockwork MOD??
Thanks!

Yes correct order.
Wipe again? In your list I can't find the first factory reset, but yes you should wipe data/factory reset, cache and dalvik cache (under advanced) at that point.
After flashing you can restore your apps with titanium, restoring the nandroid (in recovery) will revert your phone back to the state it was of the nandroid so leedroid will be gone. Personally i don't use titanium so can't tell you how to do that, but i sync my apps with appbrain and reinstall them again after flashing.
I do know that is you want to use titanium the backup needs to be copied back to the sd card.

TheGhost1233 said:
Yes correct order.
Wipe again? In your list I can't find the first factory reset, but yes you should wipe data/factory reset, cache and dalvik cache (under advanced) at that point.
After flashing you can restore your apps with titanium, restoring the nandroid (in recovery) will revert your phone back to the state it was of the nandroid so leedroid will be gone. Personally i don't use titanium so can't tell you how to do that, but i sync my apps with appbrain and reinstall them again after flashing.
I do know that is you want to use titanium the backup needs to be copied back to the sd card.
Click to expand...
Click to collapse
Do I have to do a factory reset from recovery at first?
Also after formatting the SD card with the FAT32 and ext3 partitions, do I copy back the previous contents of the SD card back to the phone along with the LeeDroid ROM?

Not before the nandroid if you meant that, wipe before flashing leedroid. So once you're in recovery to flash the rom, first wipe data/factory reset, cache and dalvik cache and then flash leedroid in the same session (without rebooting).
Best is to copy back the contend of the sd card, however if you want to start with a clean cart you can also just copy back the clockworkmod folder and the titanium folder.

TheGhost1233 said:
Not before the nandroid if you meant that, wipe before flashing leedroid. So once you're in recovery to flash the rom, first wipe data/factory reset, cache and dalvik cache and then flash leedroid in the same session (without rebooting).
Best is to copy back the contend of the sd card, however if you want to start with a clean cart you can also just copy back the clockworkmod folder and the titanium folder.
Click to expand...
Click to collapse
Thanks again mate.
So here's another of my doubt -- say, I copy the LeeDroid ROM to the SD and boot into recovery to flash the ROM and do a factory reset, would this not delete the ROM also from the SD card? My first ROM flashing and hence these doubts :-o
Thanks for your patience.
Can I just copy back the Titanium backup folder after booting into LeeDroid ROM? :-o

Sd card won't be affected by a factory reset nor by flashing.
You can copy the titanium folder whenever you want.

TheGhost1233 said:
Sd card won't be affected by a factory reset nor by flashing.
You can copy the titanium folder whenever you want.
Click to expand...
Click to collapse
Thanks again! Can't hit the "Thanks" more than 5 times!
Shall get down to flashing the ROM..
Shall drop by here for any further doubts. You've been a great help!
Cheers!

[Q] SDCard Mounting problem

I have the following problem:
-some days ago I root at the phone and followed a tutorial and I wanted to put GingerVillian 1.4 rom.
-I encountered during flashing sdcard problem in the sense that it did not want to partition, after countless attempts on win then on linux failed. It ends almost immediately with full option and run ext2 to ext3 getting error 'ext3 fs' via adb!
Finally (I did not explain why) PartitionSD worked in recovery mode. I realized that I have to go for it took a few seconds (before it ends almost instantly (I say only one point for the work phase)) Then I upgrade ext2 to ext 3.
I installed the custom ROM.
Everything was ok / functional. I moved and dalvin-cache to sd: a2db cachesd.
My problem is yet to come, do not know why I got the impression (or so I understand) that the nand backup will contain information that I needed on the phone (numbers phone, msgs, etc.) and I could choose what I want to restore only. So I reboot in recovery mode and I did the restore.
Unfortunately this has restored my htc phone-sense and goes into a reboot loop as long the card is inserted. I removed the card and I could enter the system.
Unfortunately does not recognize any card (I tested with the default sdcard that came with, it boot even though he just does not mount)
I also entered the recovery mode: and tried to format (same error as at beginnin no chance error "run via adb") and I tried to mount from the recovery options:
Error Can not mount / dev/block/mmcblk0p1
I note that the root has been preserved a2db I no longer recognized in the terminal emulator (somewhere logical since now is htc sense again)
Can anyone help me?

OK. I suggest you should start from scratch. Just take your sd card out your phone.
First fix your sd card:
-Boot a Gparted live cd.
-Format your SD card to one big fat32 partition.
Then do this:
-Download a rom without A2SD or anything like that. For example: Oxygen 2.0.1 (in fact it has kind of A2SD support, but if you don't have an EXT partition it doesn't matter. nothing can go wrong on that)
-Put that rom on your SD card and boot in recovery. (Vol down + power button, you'll enter fastboot. wait 10 seconds. select in the fastboot menu: 'recovery'.)
-full wipe. Everything. data, factory reset, dalvik cache. everything,
-install rom.
Post your results.

[U8650] ClockworkMOD v5.0.2.7 for Huawei

- Unrar "Huawei U8650.rar ClockworkMod 5.0.2.7."
2 - Turn off your cell phone battery 5sec, so put in again and enter fastboot mode: (VOL- and POWER simultaneously for 25sec)
3 - Connect mobile phone to the PC.
4 - Execute: "ClockworkMod 5.0.2.7 (Bootloader-Volum DOWN + POWER)"
5 - Run "reboot" (even DO NOT take the cable)
6 - You are now in ClockworkMod 5.0.2.7
(if windows do not find the drivers, look them in the folder "Drivers for Huawei U8650")

This should of been posted in the dev section on XDA,just giving you some advice
If I helped, give thanks, if you please.
........Death before dishonor........
Team inferno
Leader

Mr.Highway said:
This should of been posted in the dev section on XDA,just giving you some advice
If I helped, give thanks, if you please.
........Death before dishonor........
Team inferno
Leader
Click to expand...
Click to collapse
Thx for the advice.

CWM 5.0.2.7 ignoring ext partition?
Hi everybody. I have installed CWM v5.0.2.7 on my SONIC U8650 smartphone. I'm having a slight problem with this recovery (same occurred with previous version 4.0.1.4). It's not saving the ext partition that I have on the sd card. When I perform a backup through CWM, it skips the saving of sdext as this partition is not being found. Also, with previous CWM version 4.0.1.4, there was an option to manually mount the partition (just in case it is not found at the time of backup) in the "Mounts and storage" option. This option is no longer present in CWM 5.0.2.7 so I can't manually mount the partition (whether this would let CWM recognize the partition and make a proper backup of it). In the end I'm not able to have sdext fully backed up (I resorted at doing a manual backup on my notebook with LINUX with partimage) along with all the other partitions such as /system, /data, /cache etc etc. I therefore wonder if this is a bug and if there's a way to get around this.
I have another smartphone with CWM v5.0.2.3 installed and on this one the backup of the sd-ext partition does work (and it is ext4, not ext3). I wonder if on this 5.0.2.7 version for SONIC, ext3 partitions would be recognized or not.
P.S.: The CWM 5.0.2.7 I installed was taken from here. And this is the installation guide. Is this the same CWM as the one posted here?
EDIT: I have flashed even this version posted here and still the same problem.... it desn't backup my sd-ext partition. It does backup boot_image, recovery_image, system, data, android_secure, cache but not sd-ext (no sd-ext found).

LBTRAVA said:
Hi everybody. I have installed CWM v5.0.2.7 on my SONIC U8650 smartphone. I'm having a slight problem with this recovery (same occurred with previous version 4.0.1.4). It's not saving the ext partition that I have on the sd card. When I perform a backup through CWM, it skips the saving of sdext as this partition is not being found. Also, with previous CWM version 4.0.1.4, there was an option to manually mount the partition (just in case it is not found at the time of backup) in the "Mounts and storage" option. This option is no longer present in CWM 5.0.2.7 so I can't manually mount the partition (whether this would let CWM recognize the partition and make a proper backup of it). In the end I'm not able to have sdext fully backed up (I resorted at doing a manual backup on my notebook with LINUX with partimage) along with all the other partitions such as /system, /data, /cache etc etc. I therefore wonder if this is a bug and if there's a way to get around this.
I have another smartphone with CWM v5.0.2.3 installed and on this one the backup of the sd-ext partition does work (and it is ext4, not ext3). I wonder if on this 5.0.2.7 version for SONIC, ext3 partitions would be recognized or not.
P.S.: The CWM 5.0.2.7 I installed was taken from here. And this is the installation guide. Is this the same CWM as the one posted here?
EDIT: I have flashed even this version posted here and still the same problem.... it desn't backup my sd-ext partition. It does backup boot_image, recovery_image, system, data, android_secure, cache but not sd-ext (no sd-ext found).
Click to expand...
Click to collapse
Hi dude:
If you wanna sd-ext on your sd card you must follow (exactly) this easy steps.
1- Full format in FAT32 your SD card with Mini Partition 7 (windows) or gparted (linux); per example: Primary FAT32
2- put your sd card into your phone and get into recovery menu.
---go to "mounts and storage" and format this parts:
---/boot
---/cache
---/data
---/sdcard
---/system
3- Go to the beggining of recovery menu and select:
..."wipe data/factory reset"...(say YES)
..."wipe cache partition"...(say YES)
Go to ...advanced ..."wipe Dalvik Cache"...(say YES)
...go back...
5- Go to...advanced...partition SD card (say 512Mb to ext and64Mb to swap)
...go back...
...go to...mounts & storage... mount USB storage...
... conect the phone via USB and pass your favourite ROM to the cellular
6- select "unmount"
7- Go to "Go Back"
8- Select "install zip from sdcard"... "chose zip from sdcard" and select your ROM
10- Say YES and wait untill your ROm is installed
Congratz, now you have your U8650 with custom ROM and ext partition with swap
P.S. I know the steps are some tedious think but, it works at 110% man
Greetings from spain

Please help! Huawei u8652 (At&t Fusion)
Am stuck here with an At&t fusion which a friend purchased a not long ago. He set it up with a lock pattern but unfortunately his colleague took it up and tried more than 5times. Now the phone is asking for the gmail account used to set it up. Which he did not change when he got it. I would like you to give a step by step guide to get the cwm on it in other to flash it with custom rom. The menu can't be accessed so I thought your method would be the best.

klurosu said:
Hi dude:
If you wanna sd-ext on your sd card you must follow (exactly) this easy steps.
1- Full format in FAT32 your SD card with Mini Partition 7 (windows) or gparted (linux); per example: Primary FAT32
2- put your sd card into your phone and get into recovery menu.
---go to "mounts and storage" and format this parts:
---/boot
---/cache
---/data
---/sdcard
---/system
3- Go to the beggining of recovery menu and select:
..."wipe data/factory reset"...(say YES)
..."wipe cache partition"...(say YES)
Go to ...advanced ..."wipe Dalvik Cache"...(say YES)
...go back...
5- Go to...advanced...partition SD card (say 512Mb to ext and64Mb to swap)
...go back...
...go to...mounts & storage... mount USB storage...
... conect the phone via USB and pass your favourite ROM to the cellular
6- select "unmount"
7- Go to "Go Back"
8- Select "install zip from sdcard"... "chose zip from sdcard" and select your ROM
10- Say YES and wait untill your ROm is installed
Congratz, now you have your U8650 with custom ROM and ext partition with swap
P.S. I know the steps are some tedious think but, it works at 110% man
Greetings from spain
Click to expand...
Click to collapse
Sorry for the late reply and many thanks for the tip. I have been using the SONIC so far without the need to restore the system which works fine, so it was not urgent and therefore I kept it as it was, never tried again to overcome the problem. Only a question: does this procedure (different from the one I used) let the system correctly generate the backup of /sdext partition in CWM? Because I don't see why it would work with this procedure and not with my current sdext partition, which I created using gparted on a linux notebook.

Easy as pie, thank you.

Upgrading, Modifying and Unlocking > [U8650] ClockworkMOD v5.0.2.7 for Huawei
I've been having similar problems with creating/saving the partitions. I used a procedure like yours and managed to get the partitions created.
But your write hits it on the head......thanks.
klurosu said:
Hi dude:
If you wanna sd-ext on your sd card you must follow (exactly) this easy steps.
1- Full format in FAT32 your SD card with Mini Partition 7 (windows) or gparted (linux); per example: Primary FAT32
2- put your sd card into your phone and get into recovery menu.
---go to "mounts and storage" and format this parts:
---/boot
---/cache
---/data
---/sdcard
---/system
3- Go to the beggining of recovery menu and select:
..."wipe data/factory reset"...(say YES)
..."wipe cache partition"...(say YES)
Go to ...advanced ..."wipe Dalvik Cache"...(say YES)
...go back...
5- Go to...advanced...partition SD card (say 512Mb to ext and64Mb to swap)
...go back...
...go to...mounts & storage... mount USB storage...
... conect the phone via USB and pass your favourite ROM to the cellular
6- select "unmount"
7- Go to "Go Back"
8- Select "install zip from sdcard"... "chose zip from sdcard" and select your ROM
10- Say YES and wait untill your ROm is installed
Congratz, now you have your U8650 with custom ROM and ext partition with swap
P.S. I know the steps are some tedious think but, it works at 110% man
Greetings from spain
Click to expand...
Click to collapse

Worked for me, thanx.
Now running Fundowsky 4.1.1 Rom

klurosu said:
- Unrar "Huawei U8650.rar ClockworkMod 5.0.2.7."
2 - Turn off your cell phone battery 5sec, so put in again and enter fastboot mode: (VOL- and POWER simultaneously for 25sec)
3 - Connect mobile phone to the PC.
4 - Execute: "ClockworkMod 5.0.2.7 (Bootloader-Volum DOWN + POWER)"
5 - Run "reboot" (even DO NOT take the cable)
6 - You are now in ClockworkMod 5.0.2.7
(if windows do not find the drivers, look them in the folder "Drivers for Huawei U8650")
Click to expand...
Click to collapse
It's a really simple guide but download link is broken, please help

useless download link
download link doesn't work anymore
PLZ change it.

Wiped T310, no OS, unable to mount internal SD

Prior to today, I had not installed TWRP or rooted my T310 device. I believed I followed the instructions to root my device correctly (found here). Going through TWRP, I rebooted the system to install the Superuser package. I then rebooted the system, loaded up TWRP, and began to do a system wipe (followed instructions found here) to prep the flash of the rom and gapps.
I selected the following partitions to wipe: Dalvik cache, system, data and data. The instructions werent clear, so I checked both 'data' boxes.
After the wipe executed, I went to flash the rom and GAPPS I loaded to the internal sd card aaaaand... there were no .zip files. Crap. I went to reboot TWRP and it alerted me that my device does not appear to be rooted. Double crap. Not panicking, I went to mount and tried to see if I could mount the internet SD card to my device. Nothing. Windows now shows a 'Samsung_Android' device but it is listed under 'unspecified'. Reloading the drivers have done no good.
I'm guessing SuperUSer was never installed correctly *or* I did something during the reset.
I, of course, did not perform a backup prior to all of these. I have rooted my devices multiple times and it was always a breeze so why backup now? Weell...
So now I'm sitting here with a nonSU device, with no OS, no backup, and I'm unable to connect my device to Windows. Outside of loading a rom from an external SD Card, what options do I have?

jaredmac11 said:
Prior to today, I had not installed TWRP or rooted my T310 device. I believed I followed the instructions to root my device correctly (found here). Going through TWRP, I rebooted the system to install the Superuser package. I then rebooted the system, loaded up TWRP, and began to do a system wipe (followed instructions found here) to prep the flash of the rom and gapps.
I selected the following partitions to wipe: Dalvik cache, system, data and data. The instructions werent clear, so I checked both 'data' boxes.
After the wipe executed, I went to flash the rom and GAPPS I loaded to the internal sd card aaaaand... there were no .zip files. Crap. I went to reboot TWRP and it alerted me that my device does not appear to be rooted. Double crap. Not panicking, I went to mount and tried to see if I could mount the internet SD card to my device. Nothing. Windows now shows a 'Samsung_Android' device but it is listed under 'unspecified'. Reloading the drivers have done no good.
I'm guessing SuperUSer was never installed correctly *or* I did something during the reset.
I, of course, did not perform a backup prior to all of these. I have rooted my devices multiple times and it was always a breeze so why backup now? Weell...
So now I'm sitting here with a nonSU device, with no OS, no backup, and I'm unable to connect my device to Windows. Outside of loading a rom from an external SD Card, what options do I have?
Click to expand...
Click to collapse
You can either download the whole firmware and use Odin to flash or get adb setup and push a rom zip to the internal card using adb.
Sent from my SM-N900V using Tapatalk

hi,
you will need a microsd card 32gb and properly formatted that comes with a card reader for your pc.
download your rom and get it onto the card, insert the card into your device
boot to twrp, and flash,
now, if twrp still spits the no os message at you, which is an issue with twrp,
you next need to go to your wipe options, select advanced and do a full data format/wipe,
NOT SYSTEM, DATA. meaning /data and /data/media. when that completes you should be sorted
but expect your initial boot of the new rom to take a little longer.
never wipe system with twrp. the rom's updater-script will manage that function.
m

Thank you both. I lost my SD cards and card reader in a move so while that orders, I will attempt to utilize ADB. I'm pretty green but I'm certain there are guides out there..

moonbutt74 said:
hi,
you will need a microsd card 32gb and properly formatted that comes with a card reader for your pc.
download your rom and get it onto the card, insert the card into your device
boot to twrp, and flash,
now, if twrp still spits the no os message at you, which is an issue with twrp,
you next need to go to your wipe options, select advanced and do a full data format/wipe,
NOT SYSTEM, DATA. meaning /data and /data/media. when that completes you should be sorted
but expect your initial boot of the new rom to take a little longer.
never wipe system with twrp. the rom's updater-script will manage that function.
m
Click to expand...
Click to collapse
I'm having a hell of a time getting the rom to install from the SD card. I believe I am not formatting the card correctly. Is there a guide on how to do so? I have a primary partition in SD in FAT32 and the other partition as EXT4 but no luck. Any help is appreciated.

jaredmac11 said:
I'm having a hell of a time getting the rom to install from the SD card. I believe I am not formatting the card correctly. Is there a guide on how to do so? I have a primary partition in SD in FAT32 and the other partition as EXT4 but no luck. Any help is appreciated.
Click to expand...
Click to collapse
hi,
your external sdcard should be formatted as single partition fat32 unaligned,
if you running windows, use bootice, look it up
On linux , gparted may give you issues, if so, on debian at least there is another better utility
though the name escapes me at the moment, disk manager i think.
m

moonbutt74 said:
hi,
your external sdcard should be formatted as single partition fat32 unaligned,
if you running windows, use bootice, look it up
On linux , gparted may give you issues, if so, on debian at least there is another better utility
though the name escapes me at the moment, disk manager i think.
m
Click to expand...
Click to collapse
Well I was able to find a good stock firmware download, flashed that via Odin and I'm back to square 1. I am going to forego the external SD route. Perhaps too technical for me or some other hang up is abound but I am leaving that method alone for now. Thank you for your help : )