Okay I Unrooted My Sprint GS3 Through the SUPERSU App Now It Wont Turn On Please Help Asap
Did you do anything else to it? Did you try a battery pull; did you do it at low charge?
teh roxxorz said:
Did you do anything else to it? Did you try a battery pull; did you do it at low charge?
Click to expand...
Click to collapse
i think my battery was low
nunuhodge said:
i think my battery was low
Click to expand...
Click to collapse
well i'd try putting it on the charger, in a wall outlet, for like 45s, then try to turn it on.
teh roxxorz said:
well i'd try putting it on the charger, in a wall outlet, for like 45s, then try to turn it on.
Click to expand...
Click to collapse
what if that doestnt work?
nunuhodge said:
what if that doestnt work?
Click to expand...
Click to collapse
Then you'll have to try something else. I never used the supersu unroot, but it shouldn't have broken anything serious.
teh roxxorz said:
Then you'll have to try something else. I never used the supersu unroot, but it shouldn't have broken anything serious.
Click to expand...
Click to collapse
well what should i do since it still wont come on even after i charged it?
Try putting it in Download mode by pressing the Power, Home, and Volume down button until the phone screen turns on. If it turns on you should see a Warning message, press the Volume up button. Once you're there follow the guide here: http://www.qbking77.com/how-to-unroot/unroot-unbrick-the-samsung-galaxy-s-iii.html
porshce2 said:
Try putting it in Download mode by pressing the Power, Home, and Volume down button until the phone screen turns on. If it turns on you should see a Warning message, press the Volume up button. Once you're there follow the guide here: http://www.qbking77.com/how-to-unroot/unroot-unbrick-the-samsung-galaxy-s-iii.html
Click to expand...
Click to collapse
Got it covered via pm, though good looking out.
porshce2 said:
Try putting it in Download mode by pressing the Power, Home, and Volume down button until the phone screen turns on. If it turns on you should see a Warning message, press the Volume up button. Once you're there follow the guide here: http://www.qbking77.com/how-to-unroot/unroot-unbrick-the-samsung-galaxy-s-iii.html
Click to expand...
Click to collapse
but my phone wont connect too the computer
nunuhodge said:
but my phone wont connect too the computer
Click to expand...
Click to collapse
If you can get into download mode on the phone, make sure you have the proper drivers installed on your computer. I believe this is what you need.
Can you enter in Recovery Mode?
Try flashing a ROM. If you don't have any ROM, try downloading one in your PC, put it in a sdcard and then flash it.
Sent from my SPH-L710
Related
Bell Galaxy S3 running stock JB rooted
I went to flash to Cyanogenmod 10.1 Nightly, it failed (Error status 7) so I attempted to reboot. Screen went black and stayed black, I left it for a few minutes, nothing happened then tried a battery pull. Now nothing. When I plug into my computer it makes the connect/disconnect chime but nothing else. If I hold down the power for ~10sec my laptop makes the disconnect chime, then when I release the power button it reconnects to my laptop (not sure if that helps any)
Just to further clarify, I cannot get to the download or recovery mod, screen is blank, no led when plugged in either.
Is it hard bricked?
I am looking at mobiletechvideos.com at their JTAG repair service. Is that my only/best option?
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-iii-jtag-brick-repair/
If all you did was try to flash cm10.1 then you are not bricked. You might not be doing the 3 button combo correctly to get back into recovery. Do this...
Pull Battery so power down device and then put it back in.
Hold volume Down, Home, then Power Button.
Release all of them when the 1st screen pops up. It's all about timing here.
That should take you back into recovery so you can just restore the nandroid backup you should've made prior to flashing anything.
No good, the screen is pure black no matter if I just try to power on, vol up + power + home, or vol down + power + home. Black screen.
Pull your battery, leave it out, and then plug it in.. no buttons or anything, it should turn on and see if it gets to the battery charging screen (which should show a lightning bolt only).
If it gets that far, power button and home button until you feel it vibrate, let go and it should boot.. post if it doesn't..
Don't press volume buttons, just home/power combo until it vibes..
Ok, so I did like you said, pulled battery and plugged the phone in to charge. I now get a solid red LED (this did not happen with the battery in), no lightning bolt though. The red LED turns off after about 2 minutes.
mooseknuckles1 said:
Ok, so I did like you said, pulled battery and plugged the phone in to charge. I now get a solid red LED (this did not happen with the battery in), no lightning bolt though. The red LED turns off after about 2 minutes.
Click to expand...
Click to collapse
Well, at least the power connector inside isn't busted.. that's a good thing..
with it plugged in, does it turn on like normal? Just regular "boot my phone" mode, no recovery or download?
Try while the LED is on, and if nothing, try it after it goes out.. as I'm not entirely sure what that could mean..
Wiltron said:
Well, at least the power connector inside isn't busted.. that's a good thing..
with it plugged in, does it turn on like normal? Just regular "boot my phone" mode, no recovery or download?
Try while the LED is on, and if nothing, try it after it goes out.. as I'm not entirely sure what that could mean..
Click to expand...
Click to collapse
doesnt turn on at all, still just black screen. I tried the home+power button when the LED goes out, no luck.
mooseknuckles1 said:
doesnt turn on at all, still just black screen. I tried the home+power button when the LED goes out, no luck.
Click to expand...
Click to collapse
Just the power button.. no volume/home buttons..
If all that was done was updating CWM on an already rooted phone, then only your recovery is borked, which is still repairable.. but if you were flashing something else, say CF-AutoRoot or a ROM, then I need to know..
Since you said Error=7, then I can assume you already had a working copy of CWM on it.. correct?
Ya I already had CWM on it. I was trying to flash Cyanogenmod 10.1 nightly (todays release) on to the phone. I had Cyanogen10 on it a while back then switched back to stock firmware. I was curious as to the new JB4.2 so I wanted to try out Cyanogenmod 10.1
Wiltron said:
Just the power button.. no volume/home buttons..
If all that was done was updating CWM on an already rooted phone, then only your recovery is borked, which is still repairable.. but if you were flashing something else, say CF-AutoRoot or a ROM, then I need to know..
Since you said Error=7, then I can assume you already had a working copy of CWM on it.. correct?
Click to expand...
Click to collapse
the OP said in 1st post that he was flashing a rom. never mentioned cwm. the only way to have flashed a rom in the first place and gotten a status 7 would have been in a custom recovery.
reserved
Any chance you flashed an international ROM?
upndwn4par said:
Any chance you flashed an international ROM?
Click to expand...
Click to collapse
exactly.
but what all is actually accomplished before an error message?
xBeerdroiDx said:
exactly.
but what all is actually accomplished before an error message?
Click to expand...
Click to collapse
I still have a copy of the zip file on my computer, exact file name is cm-10.1-20130422-NIGHTLY-d2att.zip i cross checked with the Cyanogenmod site it says it is the proper ROM .zip to use
xBeerdroiDx said:
exactly.
but what all is actually accomplished before an error message?
Click to expand...
Click to collapse
I am not familiar with the partitions on that device, so I can't say for sure. But all it takes is one file installed in the wrong place and you'd be in trouble. And if that file gets installed in the recovery partition....
Edit:
mooseknuckles1 said:
I still have a copy of the zip file, exact file name is cm-10.1-20130422-NIGHTLY-d2att.zip i cross checked with the Cyanogenmod site it says it is the proper ROM .zip to use
Click to expand...
Click to collapse
Yup, that's the right one.
Could be the SGS3 sudden death???
upndwn4par said:
I am not familiar with the partitions on that device, so I can't say for sure. But all it takes is one file installed in the wrong place and you'd be in trouble. And if that file gets installed in the recovery partition....
Click to expand...
Click to collapse
i hear ya.
i thought thats why the script was set to check the recovery partition to ensure it was a compatible (up-to-date) platform to install from. i dont understand why it would begin installing and then check. but then, i'm no recovery coder
What about forcing download mode ? I.e. volume down+home and no battery and then plugging in the usb cord. Then put in battery after its in download mode ?
(IIRC)
Sent from my SAMSUNG-SGH-I747 using xda premium
hednik said:
What about forcing download mode ? I.e. volume down+home and no battery and then plugging in the usb cord. Then put in battery after its in download mode ?
(IIRC)
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Nope, nothing.
I want to thank everyone for the help and input so far!
There is no one in town here than can unbrick a hard bricked phone, but Toronto is only a 50min drive and there are a few places that will do it (~$70), or I can order one of those jigs online that plug into the microUSB port for about $60. It's looking like I will be going one of those routes.
mooseknuckles1 said:
Nope, nothing.
I want to thank everyone for the help and input so far!
There is no one in town here than can unbrick a hard bricked phone, but Toronto is only a 50min drive and there are a few places that will do it (~$70), or I can order one of those jigs online that plug into the microUSB port for about $60. It's looking like I will be going one of those routes.
Click to expand...
Click to collapse
um, usb jigs are about $3 on eBay.
i'm assuming you mean send it in for jtag?
xBeerdroiDx said:
um, usb jigs are about $3 on eBay.
i'm assuming you mean send it in for jtag?
Click to expand...
Click to collapse
Jig can work for the gs3. They are cheap no matter what. I used them on my cappy.
Sent from my SAMSUNG-SGH-I747 using xda premium
Hi.
I got all the files downloaded, used fastboot got it unlocked to re flash it , but says battey low, just about to run the script to charge the battery then phone went dead. I cant get the phone into bootloader, its totally dead, so how can I move on from this?
Thanks, Dan.
Rectro30 said:
Hi.
I got all the files downloaded, used fastboot got it unlocked to re flash it , but says battey low, just about to run the script to charge the battery then phone went dead. I cant get the phone into bootloader, its totally dead, so how can I move on from this?
Thanks, Dan.
Click to expand...
Click to collapse
try to plug it into the wall charger and leave it for about one hour... then try to wake it and see if you can charge it in some way
lukes91 said:
try to plug it into the wall charger and leave it for about one hour... then try to wake it and see if you can charge it in some way
Click to expand...
Click to collapse
Thanks for reply. I got a fully charged battery from another phone of the same model, put it in my phone, and its dead, wont start up what so ever?
Rectro30 said:
Thanks for reply. I got a fully charged battery from another phone of the same model, out it in my phone, and its dead, wont start up what so ever?
Click to expand...
Click to collapse
have you tried to keep the power button pressed for about 10 seconds? do the soft touch buttons flash if you do so?
lukes91 said:
have you tried to keep the power button pressed for about 10 seconds? do the soft touch buttons flash if you do so?
Click to expand...
Click to collapse
Iv tried holding power in for a while, also with combos of up, and down vol buttons unto 2 min, nothing, totally dead.
Rectro30 said:
Iv tried holding power in for a while, also with combos of up, and down vol buttons unto 2 min, nothing, totally dead.
Click to expand...
Click to collapse
so i fear it's broken
Hello everyone.
I apologize for my bad English.
My Htc is dead and will not turn on. I make a list with the details hoping someone can help me.
** The phone will not turn on and the display remains black.
**The phone does not emit any sound and makes no vibration.
**If I connect the charger the phone is charging properly. You turn on the red light and after 10/15 seconds the green one.
**If I connect the phone to the PC 4 devices are recognized but one is not installed. (Attach photo)
**Try and try again to connect the phone to the PC on one occasion, the display has flashed 3 times and for a split second it appeared the inscription HTC.
---- List of tests done:
*I tried to hold down the power button for several seconds (10 to 40).
*I tried to press both volume keys and the power button.
*Replaced FLEAT the power button.
I really hope that someone can help me!!
Thank you!! Thank you!!
Does anyone have any advice?
Can you enter hboot?
Sent from my One X using XDA Premium 4 mobile app
Usura666 said:
Does anyone have any advice?
Click to expand...
Click to collapse
Try to go in bootloader when the phone is off pres volume down + power button until you go in bootloader if you can go in bootloader you can Unlock bootloader after this flash Philz 5.15.9. recovery and then custom rom or nand backup and it will be good when you are in bootloader to post here result from command fastboot getvar version-main
I tried to get into bootloader mode but nothing happens ...
You need to hold power and volume down until you get into bootloader
Sent from my One X using XDA Premium 4 mobile app
Usura666 said:
I tried to get into bootloader mode but nothing happens ...
Click to expand...
Click to collapse
and disable fast boot in power settings
Thant said:
and disable fast boot in power settings
Click to expand...
Click to collapse
The phone will not turn on. The only thing that happens is that charges the battery and if I connect it to the PC recognizes 4 devices.
Usura666 said:
The phone will not turn on. The only thing that happens is that charges the battery and if I connect it to the PC recognizes 4 devices.
Click to expand...
Click to collapse
ok then press power button for 10-15 sec to turn off the phone after this press volume down + power buttton until you are in bootloader
Thant said:
ok then press power button for 10-15 sec to turn off the phone after this press volume down + power buttton until you are in bootloader
Click to expand...
Click to collapse
I tried. Nothing happens.
[
Usura666 said:
I tried. Nothing happens.
[
Click to expand...
Click to collapse
please post picture on your phone when you go in bootloader not on the computer
portssra with
Thant said:
please post picture on your phone when you go in bootloader not on the computer
Click to expand...
Click to collapse
No, I can't because it doesn't switch on.
Usura666 said:
No, I can't because it doesn't switch on.
Click to expand...
Click to collapse
man are you able to go in bootloader???? yes or no what happend when you pres volume down + power button hold the keys until you go in bootloader
Thant said:
man are you able to go in bootloader???? yes or no what happend when you pres volume down + power button hold the keys until you go in bootloader
Click to expand...
Click to collapse
Nothing happens. The phone remains off.
Usura666 said:
Nothing happens. The phone remains off.
Click to expand...
Click to collapse
are the phone have battery connect the phone to charger and hold volume down+power button and report back
If again not see anything on the display after this maybe fault display or BSD/black screen of dead/ try do pressure between the display and the right down side on the main camera
Thant said:
are the phone have battery connect the phone to charger and hold volume down+power button and report back
If again not see anything on the display after this maybe fault display or BSD/black screen of dead/ try do pressure between the display and the right down side on the main camera
Click to expand...
Click to collapse
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?
Usura666 said:
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?
Click to expand...
Click to collapse
you must to see something on the display see have new thread for apx mode PJ4610000
My 2 cents
Usura666 said:
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?
Click to expand...
Click to collapse
You never stated what happened to get your device in the state it is and i'm just assuming you did something to brick it, so here
So firstly you need to get the drivers for your device installed.
my advice download WinDroid Universal HTC Toolkit v1.1. It will allow you to easily know if your pc is recognising your device.
Once that is done you need to get your device changed sufficiently.
Go to http://www.hackmyandroid.com/comprehensive-guide-on-unbricking-the-htc-one-x/4216 and follow the instructions.
Charge HTC One X in Fastboot Mode section from the link should help you charge your device
With the ADB folder where it should be on your computer C drive and your device plugged in and recognized, charging shouldn't be a issue
this should cause your device to restart repeatedly until it reaches about 10% battery
I advice once you have completed the charging of your device to the 10% mark that you continue on to the Unbrick the HTC One X as well as the Restoring the nandroid backup sections. You can always install a custom rom like CM11 or a sense based rom instead of doing restoring a nandroid backup
Hopefully your device will be up and running
Goodluck and let me know how it went.
i have a tmobile galaxy s2 sgh-t989. i did a hard reset on the phone and something went wrong. When it rebooted and powered on i now have a black screen and a no sync error in little box. the time, bluetooth, wifi all still work. My computer doesnt recognize the phone is plugged to usb, So using odin isn't working. the phone won't go into DOWNLOAD MODE. i have kies, samsung drivers all installed on pc. I have tried using a sd card and using .zip files to recover. "E: signature verification failed" error is all i keep getting when trying the sd card method. i believe the rom is stock, ANDROID SYS RECOVERY <3e> blue screen comes on when holding vol+/-. is my phone a brick or can it be fixed is my question. i dont want to keep wasting my time if this cant be fixed.
MoneyJohnnYinCLeveland said:
i have a tmobile galaxy s2 sgh-t989. i did a hard reset on the phone and something went wrong. When it rebooted and powered on i now have a black screen and a no sync error in little box. the time, bluetooth, wifi all still work. My computer doesnt recognize the phone is plugged to usb, So using odin isn't working. the phone won't go into DOWNLOAD MODE. i have kies, samsung drivers all installed on pc. I have tried using a sd card and using .zip files to recover. "E: signature verification failed" error is all i keep getting when trying the sd card method. i believe the rom is stock, ANDROID SYS RECOVERY <3e> blue screen comes on when holding vol+/-. is my phone a brick or can it be fixed is my question. i dont want to keep wasting my time if this cant be fixed.
Click to expand...
Click to collapse
You will not be able to flash anything in stock recovery. To get into download mode, unplug the battery, plug into computer with Odin opened, hold power and two volume buttons, insert battery. You can then flash stock ROM in Odin.
Sent from my SGH-T989
jrc2 said:
You will not be able to flash anything in stock recovery. To get into download mode, unplug the battery, plug into computer with Odin opened, hold power and two volume buttons, insert battery. You can then flash stock ROM in Odin.
Sent from my SGH-T989
Click to expand...
Click to collapse
i have tried every method on this site. phone just wont go to download mode for sh*t. all i get is the recovery menu
MoneyJohnnYinCLeveland said:
i have tried every method on this site. phone just wont go to download mode for ****. all i get is the recovery menu
Click to expand...
Click to collapse
Did you try what I just posted? If you can get into recovery, you have to be able to boot into download mode somehow.
Sent from my SGH-T989
jrc2 said:
Did you try what I just posted? If you can get into recovery, you have to be able to boot into download mode somehow.
Sent from my SGH-T989
Click to expand...
Click to collapse
yes sir. tried vol+/vol- + power and plugging usb into phone. also tried leaving cord in pc and phone with battery out, then putting it back in while holding vol buttons. i release power button after the little vibrate when first turning phone on. nothing still. i ordered a jig off ebay hoping it will get into download mode.
MoneyJohnnYinCLeveland said:
yes sir. tried vol+/vol- + power and plugging usb into phone. also tried leaving cord in pc and phone with battery out, then putting it back in while holding vol buttons. i release power button after the little vibrate when first turning phone on. nothing still. i ordered a jig off ebay hoping it will get into download mode.
Click to expand...
Click to collapse
The jig should work. I found that it works better to hold it in passed the vibration until you see the download mode screen. And it is plug USB into computer and phone without pushing any buttons and then hold the 3 button combo in. If you want and easy way to root and install custom recovery once you are all fixed up, just let me know and I'll send ya some instructions.
Have a good evening,
jrc2
jrc2 said:
The jig should work. I found that it works better to hold it in passed the vibration until you see the download mode screen. And it is plug USB into computer and phone without pushing any buttons and then hold the 3 button combo in. If you want and easy way to root and install custom recovery once you are all fixed up, just let me know and I'll send ya some instructions.
Have a good evening,
jrc2
Click to expand...
Click to collapse
thanks for the help. when i get the jig in a few days will post back
MoneyJohnnYinCLeveland said:
thanks for the help. when i get the jig in a few days will post back
Click to expand...
Click to collapse
OK, that sounds great.
Have a good night
jrc2
Sent from my SGH-T989
jrc2 said:
OK, that sounds great.
Have a good night
jrc2
Sent from my SGH-T989
Click to expand...
Click to collapse
Got jig dongle in mail today. took battery off for a minute, put it in then jig. nothing still. dont know whats wrong with this phone. just wont go to download mode
MoneyJohnnYinCLeveland said:
Got jig dongle in mail today. took battery off for a minute, put it in then jig. nothing still. dont know whats wrong with this phone. just wont go to download mode
Click to expand...
Click to collapse
Put the battery in and insert the jig maybe. Make sure it is charged.
Sent from my SGH-T989
jrc2 said:
Put the battery in and insert the jig maybe. Make sure it is charged.
Sent from my SGH-T989
Click to expand...
Click to collapse
yes nothing happening. when the phones battery is dying i do get a chance to hit battery usage button. it brings up a menu where i can change vpn, tehtering, etc menus. but tethering is not lit up as option. (not recognized) i can bluetooth, NFC transfer between 2 devices, i see all these options
Try this.
Unplug phone
Remove battery and wait 10 seconds
Plug phone into computer
Hold in three button combo
Insert battery
Keep holding 3 buttons until you see download mode.
Sent from my SGH-T989
---------- Post added at 01:05 PM ---------- Previous post was at 01:04 PM ----------
How to use jig
- Turn off your phone and pull out the battery for 2 seconds.
- Put the battery back in the device and don't turn it on.
- Plug the jig into the micro USB port on the phone.
- After about few seconds, your phone should boot up automatically and bring you straight into download mode.
- Unplug the jig.
- Connect your phone with USB cable to computer and then flash your phone via the program "odin".
Click to expand...
Click to collapse
From http://forum.xda-developers.com/galaxy-s2/general/ref-usb-jig-faq-frequently-questions-t1402286
Sent from my SGH-T989
Jig
jrc2 said:
Try this.
Unplug phone
Remove battery and wait 10 seconds
Plug phone into computer
Hold in three button combo
Insert battery
Keep holding 3 buttons until you see download mode.
Sent from my SGH-T989
From http://forum.xda-developers.com/galaxy-s2/general/ref-usb-jig-faq-frequently-questions-t1402286
Sent from my SGH-T989
Click to expand...
Click to collapse
when i hold all three buttons the phone doesnt go download mode. it just pulses until i let go of power button
MoneyJohnnYinCLeveland said:
when i hold all three buttons the phone doesnt go download mode. it just pulses until i let go of power button
Click to expand...
Click to collapse
i took out battery for 10 seconds. did what you said the phone starts and just resets if i dont let go of power button.
FWIW, you only have to push both volume buttons when plugging into the computer to get to download mode.
meekrawb said:
FWIW, you only have to push both volume buttons when plugging into the computer to get to download mode.
Click to expand...
Click to collapse
I was trying to trouble shoot since he said he had tried combos like that already. Idk why the jig didn't work when the phone boots, though. Would adb reboot download work without root?
Sent from my SGH-T989
jrc2 said:
I was trying to trouble shoot since he said he had tried combos like that already. Idk why the jig didn't work when the phone boots, though. Would adb reboot download work without root?
Sent from my SGH-T989
Click to expand...
Click to collapse
i tried the jig in my note 3. turned right into download mode. wont work on the s2. i have tried 3 button and 2 button combos. recovery mode when i plug cord in holding both vol+/-
MoneyJohnnYinCLeveland said:
i tried the jig in my note 3. turned right into download mode. wont work on the s2. i have tried 3 button and 2 button combos. recovery mode when i plug cord in holding both vol+/-
Click to expand...
Click to collapse
the phone hasnt been rooted. i believe it is stock. i have the android recovery <3e> blue wiriting in recovery top screen
MoneyJohnnYinCLeveland said:
the phone hasnt been rooted. i believe it is stock. i have the android recovery <3e> blue wiriting in recovery top screen
Click to expand...
Click to collapse
when the phone is on. the screen is black and i get 1 "unable to sync" popup, and a few "application installer is not responding" wait/ok options
MoneyJohnnYinCLeveland said:
when the phone is on. the screen is black and i get 1 "unable to sync" popup, and a few "application installer is not responding" wait/ok options
Click to expand...
Click to collapse
i can take out the battery and put it in the phone, phone does not power on unless i hit power button. if i have the phone plugged in to usb, powered off/ battery in, it powers on the phone, no buttons needed, but does not recognize the usb on pc. has had a new port put in the phone also, was told thats why phone wouldnt sync. had port replaced and still cant sync
when i try to turn on my htc 10 it turns on for less than a second then immediately shuts off. also when its charging it repeatedly turns on and off. is there a fix for this?
twistedominoes said:
when i try to turn on my htc 10 it turns on for less than a second then immediately shuts off. also when its charging it repeatedly turns on and off. is there a fix for this?
Click to expand...
Click to collapse
Yes, take it for repairs.
twistedominoes said:
when i try to turn on my htc 10 it turns on for less than a second then immediately shuts off. also when its charging it repeatedly turns on and off. is there a fix for this?
Click to expand...
Click to collapse
It seems either or both are kaput:
- battery
- charging system
Rolo42 said:
It seems either or both are kaput:
- battery
- charging system
Click to expand...
Click to collapse
I think it's because I flashed the wrong ruu
twistedominoes said:
I think it's because I flashed the wrong ruu
Click to expand...
Click to collapse
Can you boot to download mode?
yldlj said:
Can you boot to download mode?
Click to expand...
Click to collapse
no
twistedominoes said:
I think it's because I flashed the wrong ruu
Click to expand...
Click to collapse
Why do you think you flashed the wrong RUU?
Why do you think flashing had anything to do with the device's current behavior?
Rolo42 said:
Why do you think you flashed the wrong RUU?
Why do you think flashing had anything to do with the device's current behavior?
Click to expand...
Click to collapse
I had clicked something when I did it but I cant remember what
twistedominoes said:
I had clicked something when I did it but I cant remember what
Click to expand...
Click to collapse
Very unlikely as it wouldn't even flash if it doesn't match your CID
yldlj said:
Very unlikely as it wouldn't even flash if it doesn't match your CID
Click to expand...
Click to collapse
then idk I cant even boot to download mode
twistedominoes said:
then idk I cant even boot to download mode
Click to expand...
Click to collapse
Have you tried holding volume down and power button?
yldlj said:
Have you tried holding volume down and power button?
Click to expand...
Click to collapse
is it possible I can post a video?
yldlj said:
Have you tried holding volume down and power button?
Click to expand...
Click to collapse
is it possible for me to post a video?
yldlj said:
Have you tried holding volume down and power button?
Click to expand...
Click to collapse
posted twice on accident
twistedominoes said:
is it possible I can post a video?
Click to expand...
Click to collapse
Not sure
twistedominoes said:
I had clicked something when I did it but I cant remember what
Click to expand...
Click to collapse
Stuff like this is why "technical support" is the way that it is.
OK, so we have no idea what you did since you're not telling us. Help us help you.
How long are you letting it sit and reboot (and leave it plugged into the charger)? The phone will do this after RUU, give it 20 mins or so before interacting with the device. To reach download mode, hold the power button and volume down button, after phone vibrates, release the power button and after menu displays, release volume down button. If this doesn't work, hold all three buttons until after back/recent buttons blink and device reboots.
What--EXACTLY--did you do before this happened? Which variant is your phone? Version? File(s) you used?
Rolo42 said:
Stuff like this is why "technical support" is the way that it is.
OK, so we have no idea what you did since you're not telling us. Help us help you.
How long are you letting it sit and reboot (and leave it plugged into the charger)? The phone will do this after RUU, give it 20 mins or so before interacting with the device. To reach download mode, hold the power button and volume down button, after phone vibrates, release the power button and after menu displays, release volume down button. If this doesn't work, hold all three buttons until after back/recent buttons blink and device reboots.
What--EXACTLY--did you do before this happened? Which variant is your phone? Version? File(s) you used?
Click to expand...
Click to collapse
I don't remember what I did
twistedominoes said:
I don't remember what I did
Click to expand...
Click to collapse
Take it for repairs.
yldlj said:
Take it for repairs.
Click to expand...
Click to collapse
now its stuck on white screen of death
twistedominoes said:
now its stuck on white screen of death
Click to expand...
Click to collapse
I'll say this one more time. Take it back for repairs.