I recently upgraded my phone from Stock 2.3.6 to Maclaw 4.0.4. I accidently flashed the ROM twice using CWM 5.0.2.6 without mounting my SD Card (/sdcard)(Not sure if it is important). Anyway, after Wiping data/Factory reset and wiping the Dalvik Cache, I rebooted my phone. After a successful reboot, It displayed a message saying "Encryption Unsuccessful" with a Reset button (which basically didn't do anything). What I did trying (Hopelessly) (using CWM) to remove this error was:
- Re flashing the ROM
- Formatting the sdcard and partitioning again
- Formatting everything (/system /data ....) and re-flashing
- Removing the battery (Hopelessly )
And with every step I re-wiped data and dalvik and rebooted with the same error.
I am thinking of restoring the stock rom and then re-installing this ROM but I'm not sure if it will be useful.
So any suggestions?
[Edit] Logcat:
11-07 09:35:38.099: E/Cryptfs(92): Bad magic for real block device /dev/block/stl13
11-07 09:35:38.099: W/CryptKeeper(469): Incomplete, or corrupted encryption detected. Prompting user to wipe.
11-07 09:35:38.099: E/Cryptfs(92): Error getting crypt footer and key
Try to install the rom with the following steps
- Boot into Recovery
- go to mounts and storage
- format /System and /data Only!
- Mount /data and /sdcard(unmount /system also)
- Flash Maclaw ICS rom
- Reboot device
- Done !
EddyGio said:
Try to install the rom with the following steps
- Boot into Recovery
- go to mounts and storage
- format /System and /data Only!
- Mount /data and /sdcard(unmount /system also)
- Flash Maclaw ICS rom
- Reboot device
- Done !
Click to expand...
Click to collapse
Didn't work! I did it step-by-step.
I posted my logcat, check updated first post.
Any Idea how to push the needed file to this folder via ADB?
Not again! First full wipe then flash ext4- formatter.zip then flash rom.
Sent from my GT-S5660 using xda app-developers app
batman38102 said:
Not again! First full wipe then flash ext4- formatter.zip then flash rom.
Click to expand...
Click to collapse
From where do I download ext4-formatter.zip?
ext4-formatter.zip says (Status 6) Installation aborded
Note that I'm moving from stock 2.3.6 to 4.0.4. Does this matters?
ZiadAk said:
ext4-formatter.zip says (Status 6) Installation aborded
Note that I'm moving from stock 2.3.6 to 4.0.4. Does this matters?
Click to expand...
Click to collapse
Where are you getting the ext4 formatter file from? If it wasn't designed or compiled specifically for the Galaxy Gio, it may not work. Have you tried the file found on this thread? It may be rare, however the ext4-formatter.zip file you downloaded could have become corrupted. If the file on the link above doesn't work, google 'Galaxy Gio ext4 Formatter' and some results should pop up.
Or instal phiexz cm7.2 there is his ext4 formatter inside :screwy:
Verstuurd van mijn GT-S5660
Here the rfs to ext4 formatter http://db.tt/rraDAX7X
Flash this first from cwm, then flash 4.0.4 maclaw or any custom ROM
Sent from my GT-S5660 using XDA Premium App
wiwid.colgate said:
Here the rfs to ext4 formatter http://db.tt/rraDAX7X
Flash this first from cwm, then flash 4.0.4 maclaw or any custom ROM
Click to expand...
Click to collapse
Thank you! I flashed your file then I flashed Maclaw's ROM like this:
EddyGio said:
Try to install the rom with the following steps
- Boot into Recovery
- go to mounts and storage
- format /System and /data Only!
- Mount /data and /sdcard(unmount /system also)
- Flash Maclaw ICS rom
- Reboot device
- Done !
Click to expand...
Click to collapse
Thank you both of you again!
Well, don't thanks to me...
That file from phiexz... I just re-upload since lot user can't download anymore...
Cheers
Sent from my GT-S5660 using XDA Premium App
Related
ClockworkMod Recovery Based 5.0.2.8 - For galaxy gio
I am not responsible for any damage to your phone
Tested & Working:
Reboot into system
Reboot into recovery
wipe data (factory reset) & cache
wipe battery & dalvik-cache
format & mount partition
install
Backup & Restore
Show log
Fix permission
Lock key
Known Issue
Used (gio,GT-S56600) for assert. so if you got assert error while intall zip package you must change assert script on updater-script into:
Code:
assert(getprop("ro.product.device") == "gio" || getprop("ro.build.product") == "gio" || getprop("ro.product.board") == "gio" ||
getprop("ro.product.device") == "GT-S5660" || getprop("ro.build.product") == "GT-S5660" || getprop("ro.product.board") == "GT-S5660");
updater-script can be found inside zip (META-INF\com\google\android\)
Not every Installable zip can handle mount system, data & cache.
so you should mount it manually before flash them. mount menu can found on: Mount & Storage Menu
Download link & Instruction
Download Link:
Recovery
ClockworkMod (cwm)
5.0.2.8
This version working on ext4 & rfs rom
(under construction) (Flash from Recovery)
(under construction) (Flash With ODIN)
5.0.2.7
If you want to use or using CyanogenMod or custom rom with ext4 internal partition, you should use cwm with ext4only
If you use stock rom or custom rom with rfs filesystem, you must use cwm with ext4+rfs
cwm-5.0.2.7-ext4only-odin.tar.md5 (Flash With ODIN)
signed_cwm-5.0.2.7-flashablezip-ext4only.zip (Flash from Recovery)
cwm-5.0.2.7-ext4+rfs-odin.tar.md5 (Flash With ODIN)
signed_cwm-5.0.2.7-flashablezip-ext4+rfs.zip (Flash from Recovery)
Gingerbread Stock Recovery
Samsung DXKT4
stockrecovery-DXKT4-odin.tar.md5 (Flash With ODIN)
signed_stockrecovery-DXKT4-flashablezip.zip (Flash from Recovery)
Tools
ext4-formatter.zip (Flash from Recovery)
NOTE: From cwm-5.0.2.8 not need to choose right cwm for your rom (ext or rfs). one cwm is can used on ext4 & rfs filesystem. but if you want to format from rfs to ext4 (example: installing cyanogenMod rom from official samsung's rom) u need ext4formatter & flash it from cwm-5.0.2.8. ext4formatter link can found above
How to Install:
you can install this recovery with ODIN or Recovery
Install with ODIN
Download & Open ODIN MULTI DOWNLOADER
Choose .ops file
check One Package
Click One Package on bottom & insert path of recovery
Click Start
Install From Recovery
Download & Place this recovery on root of your sdcard
reboot to recovery mode
install this cwm from recovery
Video Tutorial:
by: waqasshahzad1986
I was tested this cwm recovery with 8x format my sd-ext
and after format it, i try to use S2E. and S2E working perfectly.
i hope sd-ext corrupt can fixed with this version of cwm recovery
thanks again phiexz. btw if i update to 5.0.2.7 will it format my sd-ext ? i dont want to loose everything
Don't worry,it won't format your sd-ext
Sent from my GT-S5660 using XDA App
bug found!
the rfs+ext4 version can`t mount my sd-ext(it's ext4)
Sent from my GT-S5660 using XDA App
downloading signed_cwm-5.0.2.7-flashablezip-ext4only.zip (Flash from Recovery) now. i'll post info in 2 min
LE: just flashed signed_cwm-5.0.2.7-flashablezip-ext4only.zip. worked ok. ext4 is still there. it didn't get formated. but can tell you anything about the buggs cuz it was allready working for me
czkwg8 said:
bug found!
the rfs+ext4 version can`t mount my sd-ext(it's ext4)
Sent from my GT-S5660 using XDA App
Click to expand...
Click to collapse
its not bug
on rfs+ext4 version i made sd-ext filesystem on ext2.
it cant read ext4.
hmmmm, maybe i'll add ext4 on sd-ext later
phiexz said:
its not bug
on rfs+ext4 version i made sd-ext filesystem on ext2.
it cant read ext4.
hmmmm, maybe i'll add ext4 on sd-ext later
Click to expand...
Click to collapse
maybe better call it rfs+ext2 then...otherwise deceiving?
hmmmm.i think you should make ext2.ext3.ext4 to be supported at the same time!
Sent from my GT-S5660
I installed cwm 5.0.2.7ext4only, formatted the card from pc in ext4 but if I format sd-ext from recovery it's ext3, it is normal?
phiexz said:
its not bug
on rfs+ext4 version i made sd-ext filesystem on ext2.
it cant read ext4.
hmmmm, maybe i'll add ext4 on sd-ext later
Click to expand...
Click to collapse
wait for this additional first
some one from indonesian report, this cwm also make error on sd-ext
is some one also like this?
i havent found up to now.
Sent from my GT-S5660 using xda premium
but there is another problem
i cannot backup
Sent from my GT-S5660 using xda premium
No problems with new cwm
czkwg8 said:
but there is another problem
i cannot backup
Sent from my GT-S5660 using xda premium
Click to expand...
Click to collapse
where's the problem?
can u send me a log?
do a backup, and then reboot your gio
and upload log on /cache/recovery here
how can i understand what version can i install?
phiexz said:
Which one should i install?:
If you want to use or using CyanogenMod or custom rom with ext4 internal partition, you should use cwm with ext4only
If you use stock rom or custom rom with rfs filesystem, you must use cwm with ext4+rfs
If you want back to stock recovery, install stockrecovery-DXKT4
Click to expand...
Click to collapse
See it on first post.
Msiiek said:
See it on first post.
Click to expand...
Click to collapse
realy? my problem is i don't know what install
Hello,
I'm going to install cyanogenmod 7.2 on my samsung gio.. For the moment, i use the official rom.
I don't know if i have to download cwm-5.0.2.7-ext4only-odin.tar.md5 or cwm-5.0.2.7-ext4+rfs-odin.tar.md5 ? How to know my filesystem?
And i don't know if i have to install ext4-formatter.zip or not?
Someone can help me please?
Thank you and sorry for my bad english
tatchii said:
Hello,
I'm going to install cyanogenmod 7.2 on my samsung gio.. For the moment, i use the official rom.
I don't know if i have to download cwm-5.0.2.7-ext4only-odin.tar.md5 or cwm-5.0.2.7-ext4+rfs-odin.tar.md5 ? How to know my filesystem?
And i don't know if i have to install ext4-formatter.zip or not?
Someone can help me please?
Thank you and sorry for my bad english
Click to expand...
Click to collapse
Use ext4 and rfs version, formattor is not needed
Sent from my GT-S5660 using xda premium
Just as a FYI, RFS is essentially used by the stock rom only. If you come across a rom thats based on stock, chances are it will use RFS. An example would be the ArpegGioMod rom by Darkshado. If you want the most versitality, go with what voetbalremco said.
its really simple, just follow the instructions its what helped me do it on 7.1 and now with upgrading to 7.2
Hi,
Thanks you for your answer, but there are always a thing that i don't understand... I come form a stock rom, so my filesystem is RFS, but to use cyanogenmod, if need ext4 no? So i have to format in ext4 no?
You need to flash ext4-formatter.zip when you come from stock.
Verstuurd van mijn GT-S5660 met Tapatalk
BozeVogel said:
You need to flash ext4-formatter.zip when you come from stock.
Verstuurd van mijn GT-S5660 met Tapatalk
Click to expand...
Click to collapse
you dont if you use clockworkmod v....6
Sent from my GT-S5660 using xda premium
I downloaded cwm 5.0.2.7 so i have to flash in ext4 or not?
tatchii said:
I downloaded cwm 5.0.2.7 so i have to flash in ext4 or not?
Click to expand...
Click to collapse
you dont need ext formattrr
Sent from my GT-S5660 using xda premium
ok, thanks you very much
My CM7 Install guide.
-Note: Install every zip named: "update.zip" and place on the sd.
1 Download latest and install ClockworkMod Recovery (signed_cwm-5.0.2.7-flashablezip-ext4only.zip > ext4 internal partition, you should use cwm with ext4only). ( Place it on root of your sdcard. reboot to recovery mode. install this cwm from recovery)
link recovery: http://forum.xda-developers.com/showthread.php?t=1421650
NOTE 1: From cwm-5.0.2.8 not need to choose right cwm for your rom (ext or rfs). CWM can used on ext4 & rfs filesystem. But if you want to format from rfs to ext4 (example: installing cyanogenMod rom from official samsung's rom) U need ext4formatter & flash it from cwm-5.0.2.8. ext4formatter.
1.5 reboot in recovery en factory reset etc. (And cache wipen. See note 2)
2 Flash Cyanogenmod 7 ROM :
Download and copy the latest CM7 ROM to SD Card
Reboot to Recovery Mode
Select install zip from sd card
Select choose zip from sd card
Select the new CM7 ROM
Select Yes - Install update
Wait till the Installation is finish
Select reboot system now
3 flash Cyanogenmod 7 rom update. Same way as stap 2.
NOTE 2:
It's not automatically wipe your data. if you want to install fresh rom, you must wipe data before install it! If you from stock / custom rom based on rfs filesystem, u must flash ext4-formatter.zip before flash CyanogenMod. link & instruction can fount on This Thread. otherwise you'll stuck on android logo because it cant mount rfs filesystem! have problem after upgrade from earlier cyanogenMod? you should wipe your data!!
4? ext4-formatter.zip (Flash from Recovery) Not needed if: signed_cwm-5.0.2.7-flashablezip-ext4only.zip is flashed.
Sd card can be formated with a uttility form windows or from recovery.
4.5 Make a nandroid backup if you like! (Ore first a Tatanium backup of new progams installed)
5 Install & Enable a2sd Darktremor (Clean up sdcard a bit first if you like)
(This programs comes with CM7)
go to terminal emulator and write:
su
a2sd zipalign
a2sd cachesdreset.
if u want use a2sd extream (move data to sd-ext):
a2sd datasd
6 Install & Enable Simple2Ext (S2E)
(Personally i did skip step 5 and 6 for now.)
Gl
Last note: If you want to be able to install a other rom that uses a frs internal system partition it would be best to install a original rom. A rom made by Samsung (OTA its called i think) After that you're internal partition is on rfs format again.
After flashing CM 7.0.3 a long time ago, I haven't really updated anything or touched anything when it comes to the recovery, SU, etc since.
Seeing ICS, I tried to flash CM 9 RC1 Build 2 the way I've flashed other ROMs before: Loading the ROM and gapps zip to the root of my SD card, rebooting into recovery, wiping phone, wiping cache, then applying a zip. When I try to flash CM9s zip, I get the error:
E:can't open sdcard/name_of_zip.zip (bad)
I've tried various CM9 mirrors with the same result. I have a feeling it might be because I have a much outdated recovery, and SU binary?
My ROM Manager: 5.0.0.8
My ClockworkMod Recovery: 3.0.0.5 (latest 5.0.2.7?)
My SU binary: 2.3.1-ef (latest 3.1.1?)
When trying to update my SU binary it fails when copying su to /system..
Can anyone give me a starting direction on what I need to do to get CM9 flashed and working?
Thank you!
Use the superwipe + 4ext 1st. or change ur recovery.
File sytem needs to be ext4 fore ICS onwards as far as i know.
wileykat said:
Use the superwipe + 4ext 1st. or change ur recovery.
File sytem needs to be ext4 fore ICS onwards as far as i know.
Click to expand...
Click to collapse
You can run EliteMod and CM9 for example on an ext3 filesystem (the zip provided will format whichever filesystem to ext4 when done in the actual recovery).
Though I have not tried CM9 since beta13 I don't see this being a problem. Though I would advise doing a FULL WIPE (factory reset + cache + dalvik) before flashing on any brand new roms especially when going from GB to ICS.
(last time I checked clockworkmod doesn't let you format a specific filesystem or convert backups from ext3 to ext4 , for that I use the 4EXT recovery).
@ OP you should not have to copy the SU binary anywhere, it should come with CM9 anyways (just like busybox and superuser.apk). The only additional thing you may need to flash on top of it is google apps, just like CM7 would have been.
kbeezie said:
You can run EliteMod and CM9 for example on an ext3 filesystem (the zip provided will format whichever filesystem to ext4 when done in the actual recovery).
Though I have not tried CM9 since beta13 I don't see this being a problem. Though I would advise doing a FULL WIPE (factory reset + cache + dalvik) before flashing on any brand new roms especially when going from GB to ICS.
(last time I checked clockworkmod doesn't let you format a specific filesystem or convert backups from ext3 to ext4 , for that I use the 4EXT recovery).
@ OP you should not have to copy the SU binary anywhere, it should come with CM9 anyways (just like busybox and superuser.apk). The only additional thing you may need to flash on top of it is google apps, just like CM7 would have been.
Click to expand...
Click to collapse
Worked like a charm! I installed 4EXT recovery, wipe/factory reset, wipe cache, wipe dalvik cache, and CM9 installed just fine.
Thank you so much!
Problem:
I can't flash any custom rom successfully.
At first, I use CWM but I can't wipe dalvik cache.
Then, I switched to RZ recovery and it can wipe dalvik cache for me.
I wipe dalvik, data, cache before flashing many new roms, however, it just doesn;t work....just stay at s5660, some kind of screens
[solved]:
1. install EXT4 formatter via CWM5.0.2.7 rfs+ext4( I am using Stock RFS system ROM)
http://forum.xda-developers.com/showthread.php?t=1421650
If you have error status 6, unzip and repack it (save only or compressed best)
2.wipe data/factory reset and wipe data
3. advance-> wipe dalvik cache
4. flash a ext4 only CWM
5. flash MIUI ROM and it was successful
Re: frustrated flashing rom
Did you move from rfs to ext4??
Sent from my GT-S5660 using xda premium
I am using RFS format
tried cwm rfs or ext4. both not working to wipe dalvik
tried ext4 formatter but installation aborted (status 6))
anyone have idea?
Where can I find some old CWM to try? I can only find 5.0.2.7.
you need a recovery which supports RFS+EXT4 file system.check on development section.
EvilKing009 said:
you need a recovery which supports RFS+EXT4 file system.check on development section.
Click to expand...
Click to collapse
it is solved thanks
Hello everyone,
I am new here on Desire,
So I S-OFFed my desire,Flashed Custom CWM recovery,
My problem is,
Everytime i try to install a custom ROM,it shows me an error as "Installation aborted : status 0"..i tried to wipe /data,/system/cache,doing factory reset etc.none of them they helps.it always shows me this error.any solution?
Do the ROMs you are trying to install require an sdcard partition. Most do, and you'll need one anyway to install several apps.
- Flash 4EXT recovery.img using fastboot (better recovery, makes good partitions for desire unlike CWM)
- Backup and partition your sdcard using 4EXT recovery (max 2GB ext4 partition, no swap)
- Check md5sum of ROM.zip, to make sure you didnt get a bad download
- Full wipe and flash ROM.zip
EvilKing009 said:
Hello everyone,
I am new here on Desire,
So I S-OFFed my desire,Flashed Custom CWM recovery,
My problem is,
Everytime i try to install a custom ROM,it shows me an error as "Installation aborted : status 0"..i tried to wipe /data,/system/cache,doing factory reset etc.none of them they helps.it always shows me this error.any solution?
Click to expand...
Click to collapse
What rom u trying to flash? If its android 4.4 (kitkat) then u need to use the latest 4ext recovery v1.0.0.6 otherwise it just abort the install.
eddiehk6 said:
Do the ROMs you are trying to install require an sdcard partition. Most do, and you'll need one anyway to install several apps.
- Flash 4EXT recovery.img using fastboot (better recovery, makes good partitions for desire unlike CWM)
- Backup and partition your sdcard using 4EXT recovery (max 2GB ext4 partition, no swap)
- Check md5sum of ROM.zip, to make sure you didnt get a bad download
- Full wipe and flash ROM.zip
Click to expand...
Click to collapse
Is there is anyway to Flash Rom without any Sdext partition doing??
jmcclue,I was trying to installing Cool sense,mildwild roms.
EvilKing009 said:
Is there is anyway to Flash Rom without any Sdext partition doing??
jmcclue,I was trying to installing Cool sense,mildwild roms.
Click to expand...
Click to collapse
Yh so like eddie said u will need to partition ur sdcard for that rom. Theres a good guide in desire general "how to partition sdcard correctly" follow that guide and then u can flash roms. The reason is that the desire has bad/low memory so the sdext partition is needed, definitly for sense roms.