Develop Bugs

Someone, anyone please HELP with an ESN

I know I'm a noob, but I've been struggleing with this for a while now. I put in probibly 6 hours last night and haven't any clue if I'm even close to being complete.
I bought an HTC Touch MP6900SP (Sprint) and was told it had a clean ESN. Turns out it didn't and I'm up the creek because I paid cash. I bought it to replace my motor razr which has a clean ESN, but is quickly dieing. I'm trying to clone my ESN but can't get mtty to work properly. Once the ESN is swapped, the RAZR will go in my junk drawr.
I've tried to follow the steps here:
http://www.mobile-files.com/forum/showpost.php?p=355768&postcount=1
but when I go to fire up mtty I can only enter the rtask a command then the program or phone won't allow me to do anything else, even type the next command.
In the boot loader I have the following info:
VOGU100 MFG
SPL-2.31.CoKe
CPLD-3
Can someone please walk a noob through this. I'm totally new to this whole unlocking thing and could really use some help. The phone is locked to the account of the previous seller who refuses to release it. I've got the 2.31.coke on there now and when I boot it normally I also have the Alltel rom that fires up. HELP!!! PLEASE!
Edit: In MTTY when I run rtask a this is what I see, but I can't type anything after that.
rtask a
Enter Radio Bootloader
POWER ON PMIC VREG_USB : SUCCESS!

This has been covered...
SEARCH!!! MTTY is actually working, you just can't see the text you are typing... Just be careful typing everything in and you will be good to go...

Alright, I got through MTTY, and am not onto working in CDMA workshop.
I put the phone into DM mode, Active sync disconnects, but CDMA shows it is connected to Com1 port successfully, but fails when I attempt to read the ESN.
I can't seem to find the diagnostic modem drivers that I need and think the lack of the drivers is what is causing me grief now.
Believe me, I'm looking everywhere I can to get information. I've got tons of hours into this now.
Edit: Got the drivers installed and working properly. Still having problems reading from the phone with CDMA.
Edit 2: Had to figure out the proper com port in CDMA, getting warmer.

scanning and finding esn addresses right now! If this thing works I'll be so damn happy!

im still reading up on this, but seeing information that has been corrected over time, then finding some old posts that may be outdated.
using MTTY with all of the steps to superCID... is that actually changing the ESN in one failed, fast swoop? Is it actually doing what CDMA does when scanning/writing?

ESN
cox abele said:
im still reading up on this, but seeing information that has been corrected over time, then finding some old posts that may be outdated.
using MTTY with all of the steps to superCID... is that actually changing the ESN in one failed, fast swoop? Is it actually doing what CDMA does when scanning/writing?
Click to expand...
Click to collapse
Hey did you get this to work? I changed my esn last night and the phone works. Can make and receive calls. Only prob is that I can't connect to the internet. I think it is a problem with the user name/password but not sure. I keep getting the 67 error when trying to connect. I only changed the esn and nothing else.
Did you have any luck? If so what about the internet thing? Any help would be much appreciated. Been reading and trying to figure this out for a while now.
Thanks,
-T

Hey man, welcome to XDA
What Airline do you fly for? It's good too see another fellow Pilot on here.
As you can see from my sigpic, I'm with Air Canada Jazz.

b727pilot said:
Hey did you get this to work? I changed my esn last night and the phone works. Can make and receive calls. Only prob is that I can't connect to the internet. I think it is a problem with the user name/password but not sure. I keep getting the 67 error when trying to connect. I only changed the esn and nothing else.
Did you have any luck? If so what about the internet thing? Any help would be much appreciated. Been reading and trying to figure this out for a while now.
Thanks,
-T
Click to expand...
Click to collapse
Have you tried installing the DCD carrier cab. I think this is the link. Just double check.
http://dcd1182.n715dp.com/index.php?dir=carriers/

Help with ESN Change. Phone works just not internet
Csquared said:
Have you tried installing the DCD carrier cab. I think this is the link. Just double check.
http://dcd1182.n715dp.com/index.php?dir=carriers/
Click to expand...
Click to collapse
Thanks for the reply. No I had not tried the DCD carrier cab. First of all let me get this out of the way. NOOB here.
I tried researching the DCD cab because someone else suggested it and then tried it and it didn't work. I think it might be something with the user name and password for vision service. This is what I did:
Flashed the Touch (it is a sprint touch) to the 6.1 wm latest rom (sprint). Then did the esn swap from my razr (also sprint). After the esn swap I flashed again using the 6.1 sprint rom (just wanted to make sure nothing changed after I did a rom flash). Phone works fine on sprint and I even called them on it and they think it is a razr. I can make and receive calls, voicemail etc. Just can't get the internet working. Just get the 67 error. Any ideas?
-T

jmitr said:
Hey man, welcome to XDA
What Airline do you fly for? It's good too see another fellow Pilot on here.
As you can see from my sigpic, I'm with Air Canada Jazz.
Click to expand...
Click to collapse
SWA! Ever in MDW?
-T

b727pilot said:
Thanks for the reply. No I had not tried the DCD carrier cab. First of all let me get this out of the way. NOOB here.
I tried researching the DCD cab because someone else suggested it and then tried it and it didn't work. I think it might be something with the user name and password for vision service. This is what I did:
Flashed the Touch (it is a sprint touch) to the 6.1 wm latest rom (sprint). Then did the esn swap from my razr (also sprint). After the esn swap I flashed again using the 6.1 sprint rom (just wanted to make sure nothing changed after I did a rom flash). Phone works fine on sprint and I even called them on it and they think it is a razr. I can make and receive calls, voicemail etc. Just can't get the internet working. Just get the 67 error. Any ideas?
-T
Click to expand...
Click to collapse
Do you have a data plan setup with Sprint on your Razr?

Csquared said:
Do you have a data plan setup with Sprint on your Razr?
Click to expand...
Click to collapse
Yea I have the old sero plan. It includes unlimited data. I think that is what you mean. I can run opera on it so it is working.
-T

This might be trivial but lets check.
Goto:
Settings/Connections/Connections/Advanced/Select Networks
It should show Sprint in top and Work network in bottom.
Click edit under Sprint and make sure its set to #777

Then try this:
Settings/Personal/Phone/Services/Internet/Get settings
Then have IOTA done by pressing start.

No Internet Still......
Csquared said:
Then try this:
Settings/Personal/Phone/Services/Internet/Get settings
Then have IOTA done by pressing start.
Click to expand...
Click to collapse
Thanks Csquared. I tried this and this is what I got. I also have posted this at http://forum.xda-developers.com/showthread.php?p=3413006#post3413006 . Not trying to double post but was getting some help over there also.
Phone is working great using the donor ESN but no internet. Here is what I've got:
- Sprint Razr (donor ESN phone) and Sprint Touch (Had bad ESN now has Razr ESN).
- Have Data plan on my Account.
- Did the changes from the original post and phone works fine (can make and receive calls)
- When I try and connect to the internet it gives me error 67, can not connect #777 and 1012 error.
What I have tried:
- Start/settings/services/internet/get settings/ and start IOTA.
- Tried making a new connection under start/settings/connections/connections and setup a new #777 connection.
- Changed Active Profile from 0 to 1 in ##3282#
None of this worked. Under ##3282# my settings are:
User Name:
Active Profile - 1
MIP_MODE - Mobile IP Only
User Name - (My Username)@sprintpcs.com
SPI MN-HA - 4D2
SPI MN-AAA - 4D2
ReverseTunnel Pref - Enable
Home Agent IP Address - 0.0.0.0 (for some reason it will not let me edit this setting)
Primary Home Agent - 0.0.0.0
Second Home Agent - 0.0.0.0
HA Shared Secret (HEX) – Blank
AAA Shared Secret (HEX) – Bunch of characters
Advanced:
ESN - Donor ESN (From Razr)
MSID - My Phone number
Not sure if any of this makes sense. I am just trying to get the internet working. Please let me know if anyone has any ideas. It does say "Preparing vision services" when I try to connect to the internet but always fails with error 67 Username and/or Password incorrect. Also get Cannot Connect Dialed #777. Also get error code 1012 could not prepare Vision services please try again later.
Thanks very much in advance for the help!
-Tony

Well I know this is prolly not the right thread to put this under however I am not sure which is and the person who started this thread is doing what I wanted to know was possible to do. And second I was wondering how to do it. I am completely noob on this. I did as he did and bought a new phone which ended up having a bad ESN.
I have a Nokia with Verizon and it broke. They wont replace it for me so I went and bought an LGVX9100M. I have been researching for around 4 hours now and cant find a thing if I can take the ESN from my Nokia which is clean and working and put it to the LG to make it work. I am not familiar with any thing that has to do with programming cell phones or using the programs. I am however a pretty quick learner.
Is there a way to do this? Is there a program I need or a way to just do it in the phone? IF I can do this with a program how do I do it and what stuff do I have to replace the numbers with?

Bad ESN's= Unrecovered lost or stolen property, or property with a bill due over its usage.
Helping with Bad ESN's, is like helping repaint a stolen car.
WR

A "Pro" Flashing my Epic 4G to Metro

Bought an Epic 4G Touch and found a local guy on craigslist who's going to do a full flash to MetroPCS. I'm wondering if anybody has any suggestions as to what questions I should ask the guy. I'm new to this whole thing, this is my first smart phone, but I'm a quick learner.
From what I understand from my research, he's going to have to flash a custom rom on it in order for the phone's features to be fully operational. Is it important I find out which rom so I can perform my own updates, or is it going to be obvious what he did simply by looking in the settings?
Am I going to have to avoid OTA updates? Or do I just install Rootkeeper to get the updates?
I also assume that by doing this I will be stuck using the custom rom, right? Or as long as my ESN is added to the Metro system I can change it to any rom I can find that is fully operational with Metro?
Is there any other vital information I should make sure to ask for in case I need to configure anything in the future?
Would it be smarter for me to just ask him to add my ESN to metro and then flash it myself? (If I can find a guide online-- links, anybody?)
Feel free to add any information that you think might help!
Thanks in advance.

its pretty much about manually programming in your data settings 100% correctly. anyone can add an meid/esn into their database and program in your phone number(##SPC#). if you research online you can find the exact settings. i dont believe metro uses wap anymore so that certainly makes things easier.
you should be able to use ANY rom and be able to call/text/use data. the only issue you will run into(maybe.. i dont use metro) would be mms. mms sometimes is custom built for a specific phone/carrier. when you see metro/cricket custom roms.. thats generally the big modification.. the mms. you may get some little edits here and there.. changing the word sprint to metro etc... but otherwise thats pretty much it. as is.. the epic 4g touch can be manually programmed with any cdma carriers data profiles for 3g.
if you dont care about mms.. its a 100% no brainer.. take the time and do it yourself. if mms is a must.. do a little research to see if others on metro got mms working.. there will be people talking about it somewhere on the internet.
and just to add.. if u do use a custom rom for metro.. you will be stuck with that rom(unless its a freely available custom rom.. but those are rare these days.. most are sold on cdma forums for lots of $$$).

I will preface this with I've never done this before so I don't know the outcome. That said, at least in my area, the 4g is not compatible with lte, metro doesn't have 3g but 2g rttx1 should work. I don't know about you but if it were me, I wouldn't do it. That's like putting a restricting device on a Porsche so that its top speed is 30mph. 2g is practically dial up speeds. Do what you will though...

autoprime said:
its pretty much about manually programming in your data settings 100% correctly. anyone can add an meid/esn into their database and program in your phone number(##SPC#). if you research online you can find the exact settings. i dont believe metro uses wap anymore so that certainly makes things easier.
Click to expand...
Click to collapse
Thanks so much, great information. Question- Do you mean I can add my own ESN into the Metro Database myself? I thought only Metro reps could do that (independent ones for under the table).
As for the rest of the data settings, when searching for this information online, do I need to look specifically for Epic 4g Touch, or the data settings will be the same no matter what phone?
autoprime said:
if you dont care about mms.. its a 100% no brainer.. take the time and do it yourself. if mms is a must.. do a little research to see if others on metro got mms working.. there will be people talking about it somewhere on the internet.
Click to expand...
Click to collapse
Actually I don't care about mms, as long as I can do regular text messages (sms). Does this mean that if I don't care for MMS I can actually get the Epic Touch fully operational on the stock rom?
autoprime said:
and just to add.. if u do use a custom rom for metro.. you will be stuck with that rom(unless its a freely available custom rom.. but those are rare these days.. most are sold on cdma forums for lots of $$$).
Click to expand...
Click to collapse
So I couldn't re-flash it to a different rom? It's not "reversible"? (If it is possible- would I lose all the Metro data if I changed the rom?)
Thanks for the help, I've been Googling around like crazy trying to find more info, but not finding a lot. I probably should of gotten a more commonly metro flashed phone, lol. I'll keep looking around and see if I can find any guides, if I find one and can do everything myself I'd rather go that route (not to save money, just to be able to troubleshoot any issues that may arise in the future).
Edit: I've found this thread http://forum.xda-developers.com/showpost.php?p=8395950 that looks like it might be exactly what I need to do (up to step 28), and someone on this Epic Touch Forum recommended another member to this thread http://forum.xda-developers.com/showthread.php?t=1303507 but it's for Evo 3D, so not sure if it would work for the Epic. The guide starts off for phones already "flashed to metro with text and talk", though. I think I still need to pay the "Pro" to get my ESN added to the Metro Network? Are they able to add the ESN to the Metro Database and get text/talk working without flashing a custom rom?
Sorry... so many questions. I'll give lots of thanks =(
EDIT #2:
Think I got it now. Looks like I will need to get the phone Metro Flashed through my guy for talk and text (I can ask if his MMS/Web method involves a custom rom, if so I'll pass) then I can activate web (and MMS I guess) myself through these steps: http://forum.xda-developers.com/showthread.php?t=1303507
At this point (correct me if I'm wrong) I won't be locked into any custom roms and I can freely upgrade to any freely available rom (ie CM7) without affecting my Metro settings?

really not sure what the best procedure is for getting your esn added to the DB.. i would think any 3rd party metro store would be able to add it into system... as well as some people on craigslist. just look for the cheapest option.
once your esn ins in the system.. you pick a plan.. program in your phone number and msid (##SPC#) as well as write a metro PRL to the phone... and thats it for working talk/text. thats the "basic flash" most people do. only thing you cant do yourself is add meid.
and then you will eventually program data. the steps for evo 3d should be very similar to epic. other than how to get the phones into DIAG mode.. what to manually add is the same across the board... tho your username/password will be unique to you. (ppp password is based off esn.. username will be based on phonenumber).
i believe metro has recently added 3G in SOME areas.. so theres a small chance youll have that. and as for 4G... see my epic 4g touch thread on how to edit wimax settings...
ive said enough.. you should be able to take it from here.
edit: as for being "stuck" with a custom metro rom.. youd have the option to reflash anything youd like.. but the custom metro settings would probably no longer work. it would suck to pay for a custom rom that you end up wanted to switch out anyway(since it wouldnt be updated like he rest of the roms). i say pay the $10.. 15..20.. whatever it is to have esn added to the system.. then do the rest yourself.

If you search on ebay. There is a guy that can add your esn to metro for $25. Then you can flash your own custom rom, but you would have to setup your own data. If you search around, there are threads about how to setup data for metropcs around the web.

Ran outta thanks, I'll get you tomorrow
I looked it up on ebay and there's only a couple up atm and they end up being a lot, ie the cheapest is $20 but then they charge $25 shipping lol <.<
Luckily, the local guy I found on Craigslist (there are actually a lot independent metro stores in the area advertising actually) will add ESN and get talk & text working for $35. So it's not a bad deal. From there I'll get the rest working myself.
Although I'm gonna ask him about his MMS method, if it involves a custom rom I have been contemplating getting it. I been researching and it looks like all I have to do is backup the custom rom with nandroid, and I can flash to whatever rom I want, then I can always revert to the custom rom if I really want MMS working again-- if I'm unable to get it working myself.

My used Epic 4G Touch arrives in a few hours!
First thing I plan on doing is a full restore and then installing EL13+CWM. After this I'll get take it to the independent Metro store to get it flashed over to Metro. Then I'll make my first nandroid backup.
Question- By making the nandroid backup I can always revert back to the Metro data settings my guy configured, right? (In the case they get deleted through rom flashing).
Can I see all the settings he configured by reading the values set through CDMA Workshop? Would this include everything needed to make the phone fully functional on Metro again (outside of the possible custom rom to make MMS work)?
Thanks in advance.

Godswrath said:
My used Epic 4G Touch arrives in a few hours!
First thing I plan on doing is a full restore and then installing EL13+CWM. After this I'll get take it to the independent Metro store to get it flashed over to Metro. Then I'll make my first nandroid backup.
Question- By making the nandroid backup I can always revert back to the Metro data settings my guy configured, right? (In the case they get deleted through rom flashing).
Can I see all the settings he configured by reading the values set through CDMA Workshop? Would this include everything needed to make the phone fully functional on Metro again (outside of the possible custom rom to make MMS work)?
Thanks in advance.
Click to expand...
Click to collapse
nandroid wont restore data settings... but you wont need to as 3g data profiles(as well as talk/text) stick after new roms. only a ##786# full reset will wipe those settings.
you should be able to see most if not all settings with cdma ws/qpst service programming.
1. Phone number/msid has to be programmed.
2. Metro PRL Flashed
3. after step two you now have talk/text.
4. Program in 3G Profile 0/1.
5. Program PPP data profile.
6. Done. Only thing I skipped is MMS.. which will most likely be covered by a custom metro rom.. tho maybe you could take the mms ap out of the custom rom to use... but im just guessing at this point.

autoprime said:
really not sure what the best procedure is for getting your esn added to the DB.. i would think any 3rd party metro store would be able to add it into system... as well as some people on craigslist. just look for the cheapest option.
once your esn ins in the system.. you pick a plan.. program in your phone number and msid (##SPC#) as well as write a metro PRL to the phone... and thats it for working talk/text. thats the "basic flash" most people do. only thing you cant do yourself is add meid.
and then you will eventually program data. the steps for evo 3d should be very similar to epic. other than how to get the phones into DIAG mode.. what to manually add is the same across the board... tho your username/password will be unique to you. (ppp password is based off esn.. username will be based on phonenumber).
i believe metro has recently added 3G in SOME areas.. so theres a small chance youll have that. and as for 4G... see my epic 4g touch thread on how to edit wimax settings...
ive said enough.. you should be able to take it from here.
edit: as for being "stuck" with a custom metro rom.. youd have the option to reflash anything youd like.. but the custom metro settings would probably no longer work. it would suck to pay for a custom rom that you end up wanted to switch out anyway(since it wouldnt be updated like he rest of the roms). i say pay the $10.. 15..20.. whatever it is to have esn added to the system.. then do the rest yourself.
Click to expand...
Click to collapse
You can change your meid. ##YOURMSL#
Sent from my SPH-D710 using xda premium

locoboi187 said:
You can change your meid. ##YOURMSL#
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
yes it is possible to change an meid... but i'm not sure why ##MSL# is mentioned... the two are not related.

Hmmm... I'm stuck on this step :
USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default]
When I click on USB Connected it just sends me back to Home. Any ideas?
(Step 1 from http://forum.xda-developers.com/showthread.php?t=1342728)
EDIT: figured it out, had to re-install drivers and change the default location to 32-bit
Nope, still no go... Hmm Maybe I'll uninstall drivers and reinstall them. Problem is my PC isn't recognizing phone as a drive, just a device.
Yeah I dunno, gonna give up installing EL13+CWM for now and go get it flashed.
I think the problem is, when I connect the device I get "Samsung Mobile MTP Device Failed"
I downloaded the Samsung USB/Android drivers [USB/Android] and have Kies installed (Kies can't even recognize it though).

autoprime said:
yes it is possible to change an meid... but i'm not sure why ##MSL# is mentioned... the two are not related.
Click to expand...
Click to collapse
Your MSL code entered at the dialer with the "#" brings up a menu in which you can edit. I used this with a sprint tech when trying to fix my gps
Sent from my SPH-D710 using xda premium

Godswrath said:
Hmmm... I'm stuck on this step :
USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default]
When I click on USB Connected it just sends me back to Home. Any ideas?
(Step 1 from http://forum.xda-developers.com/showthread.php?t=1342728)
EDIT: figured it out, had to re-install drivers and change the default location to 32-bit
Nope, still no go... Hmm Maybe I'll uninstall drivers and reinstall them. Problem is my PC isn't recognizing phone as a drive, just a device.
Yeah I dunno, gonna give up installing EL13+CWM for now and go get it flashed.
I think the problem is, when I connect the device I get "Samsung Mobile MTP Device Failed"
I downloaded the Samsung USB/Android drivers [USB/Android] and have Kies installed (Kies can't even recognize it though).
Click to expand...
Click to collapse
Maybe you need USB debugging enabled by going to Settings > Applications > Development
Sent from my SPH-D710 using xda premium

Thanks, but no go. Have debugging checked. (I followed the tutorials to the letter)

youre trying to root?

I successfully rooted with the full restore, what I tried to do next was install EL13+CWM and I noticed 2 things:
1st) I can't get past this step: USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default - pic] (ie when I tap on "USB Connected" it just takes me back to the home screen.
2nd) I continued with the tutorial since it says it should be set correctly as default, but then when the E4GT automated rooting package (not to root, but to install EL13+CWM) it hangs saying "Waiting for device to be connected"
When looking for an answer I discovered this:Why is the install stuck waiting for device to be connected? which gave me some ideas to try, although I've tried all of them to no avail.
I should note that when I go to start->run->devmgmt.msc this:
Code:
Android Phone
SAMSUNG Android ADB Interface
Modem
SAMSUNG Mobile USB Modem
isn't listed there, like it says it should here.
I think I'm going to try to reinstall all the drivers again... Should I do this before or after connected the phone? (The first time I installed the USB/Android drivers from the tutorial before connecting my phone, but I notice after connecting the phone windows goes through the automated process of installing drivers)

<face palm>
http://androidadvices.com/enable-usb-storage-android-devices/
It was so simple, lol... To my own defense this wasn't anywhere in the tutorials
Thanks again for the help guys
EDIT: Well, looks like my problem is still here, the E4GT automated rooting package still hangs searching for device to be connected.
EDIT #2: Omg... Finally figured it out. I thought debugging was enabled (it shows a freakin' check mark) but it has to be a green check mark apparently...
Weee installed CWM, now to create a nandroid and start flashing! Think I'm going for Calkulin's rom with the ICS Theme

Another question!
Hey guys, question:
I got 2 E4GT's flashed over to MetroPCS, both are working fine, but one of them gives me this error on bootup:
Code:
Error 67: Registration failure. Your Sprint data service username
and/or password may be incorrect. Please try again.
Any ideas? Aside from the nuisance, it hasn't seemed to cause any hindrance to the features. The other phone has never given this error, though. Both are running on Calk's rom. Thx guys.

Godswrath said:
Hey guys, question:
I got 2 E4GT's flashed over to MetroPCS, both are working fine, but one of them gives me this error on bootup:
Code:
Error 67: Registration failure. Your Sprint data service username
and/or password may be incorrect. Please try again.
Any ideas? Aside from the nuisance, it hasn't seemed to cause any hindrance to the features. The other phone has never given this error, though. Both are running on Calk's rom. Thx guys.
Click to expand...
Click to collapse
if its only at bootup i wouldnt worry too much. its just the firmware trying to get a sprint connection and it failing.. since youre connected to metro. i would check ##data# > view > data profile/username.. compare whats listed for the one thats working to the one thats giving the error. are they both the same? if not, make them the same and perhaps you can avoid the error. if they are the same... its probably some little data setting somewhere that the phone doesnt like and likely not worth the hassle of poking at it more. like i first said.. the error at boot really isnt a huge deal. if it was a constant error that kept popping up then its something to look at.

Flashing Epic to Boost, quick question before purchasing donor

I have been in the process of attempting to flash my Epic 4g to boost for about a week now (with very limited time each day). Thanks to the help of some awesome people here on the forum I have made quite a bit of progress. I have however, hit a wall. I am currently attempting to use a Samsung Replenish which I purchased with GB 2.3.6 pre-installed. I have gotten to the point where I need to extract the HA/AAA keys from the donor and it is locked down tighter than (insert random virgin joke here...). I have tried two methods, method 1- reading NV Items 465,466,1192, and 1194, this method gives me four text files, each of which say access denied toward the top and give me nothing but goose eggs. method 2- using QXDM typing password (spc) which works fine, I have the right SPC and it accepts it, but then when I type the requestnvitemread ds_mip_ss_user_prof command (and I have tried prof 1 and prof 0) it says "error recieved from target". I am not familiar with anything more technical than what I explained, I know my way around these phones a bit and am technically savvy, but I do not know any code or anything like that.
I stated in my first post that I dont mind having to spend money to get my epic to boost but I would like to avoid it. With that being said, I would like to know if there is anything that I can try before pulling the trigger on a Sanyo Incognito (which to my understanding is one of the easier phones to use for this process). I have read that flashing back to froyo might help, but I cant find anything on flashing the Replenish back to Froyo as no one seems to want to do it. If anyone has any advice on flashing back to Froyo or anything else that I can try to get those keys I would be eternally grateful (well maybe for a day or two, after that I'd probably forget...anyways...)
thanks in advance for any help!!

Even though you're trying to flash an Epic 4G, this question is more applicable to a Replenish forum (if there is one), where people have experience reading these NV items on that particular model.
Some things to try:
Try first sending "password 01F2030F5F678FF9" in QXDM. (I wouldn't be surprised if this password did not work for the Replenish. Some Samsung devices have unique passwords.)
Try DFS CDMA Tool.
Try reading /nvm/num/ in QPST EFS Explorer.

etirkca said:
Even though you're trying to flash an Epic 4G, this question is more applicable to a Replenish forum (if there is one), where people have experience reading these NV items on that particular model.
Some things to try:
Try first sending "password 01F2030F5F678FF9" in QXDM. (I wouldn't be surprised if this password did not work for the Replenish. Some Samsung devices have unique passwords.)
Try DFS CDMA Tool.
Try reading /nvm/num/ in QPST EFS Explorer.
Click to expand...
Click to collapse
Yeah, unfortunately for me, this phone isn't very popular...especially in the hacking/flashing community so my resources are limited, I did not see a thread dedicated to this phone on here. I tried using the password that you gave me and it did accept it but did not change my result. I also tried using efs explorer and each file that I save/view says secret and nothing else....

Usually reading EFS is blocked until you send the 16 digit password, but it sounds like you did that already. Sorry, I've never used a Replenish, so I'm not sure what else to do.

etirkca said:
Usually reading EFS is blocked until you send the 16 digit password, but it sounds like you did that already. Sorry, I've never used a Replenish, so I'm not sure what else to do.
Click to expand...
Click to collapse
NP thanks anyway, I went ahead and bought an Incognito. I got a deal on ebay, for a nonfunctional unit with guaranteed ESN as well as USB capabilities for $35, the dealer sells them specifically for the purpose of donor/flashing. Guess I'll have to wait a few more days for an almost fully functional Epic...At least now I get to play around with some roms and fine tune that sucker to my exact liking

One more quick question though, When I get the phone, should I transfer my boost account to it BEFORE I flash the epic? or can I just flash it, call from the epic and transfer it all that way?

You need to have the incognito on boost first. When you transfer the account to incognito they will program the phone for you. I would suggest you to talk to a live person at boost when you activate the incognito. Write down the spc code and mdn number. This will save you some time. After that everything else should be easy. Program the epic with the information from incognito.
bugzy3188 said:
One more quick question though, When I get the phone, should I transfer my boost account to it BEFORE I flash the epic? or can I just flash it, call from the epic and transfer it all that way?
Click to expand...
Click to collapse
Sent from my PC36100 using XDA Premium App

help. wiped my carrier settings on boost

I have/had a Note 2 flashed to boost mobile. I messed up and wiped my carrier setting using billards custom twrp. now it won't activate. I'm gonna try the guides but I did that vbefore and had no success . Please help if you can. IKR i'm a dumbass for not doing a backup. had one. reformatted my computer though and lost it. I'll make sure to dropbox that **** next time. If anyone can team viewer me and help it would be so very helpful. yes I have the the donor incognito also. The esn and all that stayed but the phone # is all messed up

c'mon. I know someone out there knows how to help! Please PM me! PLEASE

If its just the phone# and MIN missing dial ##72786# select edit, enter your MSL then put the # and MIN back manually and reboot
SoA: Son's of Android™
I like to break stuff
We are legion, for we are many!

dcc0011 said:
I have/had a Note 2 flashed to boost mobile. I messed up and wiped my carrier setting using billards custom twrp. now it won't activate. I'm gonna try the guides but I did that vbefore and had no success . Please help if you can. IKR i'm a dumbass for not doing a backup. had one. reformatted my computer though and lost it. I'll make sure to dropbox that **** next time. If anyone can team viewer me and help it would be so very helpful. yes I have the the donor incognito also. The esn and all that stayed but the phone # is all messed up
Click to expand...
Click to collapse
Well if you MEID is still the same as the incog, no big deal, just call boost and tell them you were having issues with data on your incog and you reset the phone now you lost all your settings and need to reactivate. They will reactivate/reprogram via ##MSL#, reboot then update your PRL/Profile and you should be good to go.
Dont be afraid to call boost this is a easy fix.

thanks for all the info guys! I'm gonna try the boost thing. To clarify, my phone # and MIN are now 000000xxxx and 000000xxxx. The numbers don't relate to anything I can think of that's why I put xxxx instead of the #'s. I used cdma workshop to put my correct info for these. I'm worried about the fact that HDR AN Long password is missing when I read with DFS. I would re write it but it's the free version and the settings won't stick no matter what I do! Would the $50 paid version make them stick? I don't have the extra cash (car in the shop) @ the moment but it would be nice to know. I would hate to spend $50 and not get anything different. I've been reading for 2 days on how to do that via some other program but it's not going well. PST errors for me and I saw something about the prl being the problem and use DFS to change it. IDK how to do that exactly so I'm not gonna risk bricking this $600, marble white, sweetheart without a clear understanding how to do it and how to get the settings to stick with DFS or another program. I see comments that are very vague telling you how to do it and have purchased a manual but with DFS not sticking and QPST producing errors on the 10+ downloads I've tried I'm afraid I'm lost. If someone can tell me how to get QPST to work I would be fine!
After I give the "CALL BOOST" a try I'll report back. One things for sure, I'm kicking myself in the ass for not backing up my EFS. Deeerdider :silly:

Unknown Zone said:
Well if you MEID is still the same as the incog, no big deal, just call boost and tell them you were having issues with data on your incog and you reset the phone now you lost all your settings and need to reactivate. They will reactivate/reprogram via ##MSL#, reboot then update your PRL/Profile and you should be good to go.
Dont be afraid to call boost this is a easy fix.
Click to expand...
Click to collapse
This is nuts. lol. I went to the boost site and logged in to my account (by clicking "MY ACCOUNT". Then I clicked on update hadset (like I was changing phones) I coppied and paisted the MEID/ESN that is given for the incognito (yes, this stuck in my phone under settings/about device/Status). Then I activated the same phone again! My service bar showed the no service symbol and I rebooted my phone. Hands free activation failed. I tried to make a call and got the same old "your device is not activated" message and figured it didn't work. I put the phone on airplain mode and started installing my drivers and qpst and such on a new fresh install of windows black. 15 minutes or so passed and I took it off airplain mode and PING got a message from boost giving my account info. I dialed ##000000## and clicked edit. I viewed and checked and my phone # and MSID. It showed them correct.I backed out and hit done. the phone rebooted. Then I got a message that profile couldn't be updated and then it updated the prl and worked! I then tried to make a call and I got the Boost message "not enough money in this account to make the call" NEVER have I been so happy to hear those words!!! It's been about 45 minutes now and I still have no data. Now I will root and backup all my EFS and anything else I can. Will report back when I get data fixed!!!

[Q] Sprint to Boost with Galaxy Rush as donor

Ok I have gone through several guides, trying to get this to work. All guides mention using the incognito, but that cant possibly be the only phone that works.
I have the Galaxy Rush, Boost Mobile, 3g. I know it wont support 4g. I just want a nicer phone and happened to have teh E4GT.
I have the tools from the various incognito guides, and I get stuck at the step where I get CDMA Workshop to read my phone. I connect, I dial ##DIAG# and enter my MSL, then connect and click read. I get a failed message. Since I know my MSL already, I try skipping ahead to getting the NV items, using the MSL as the SPL and get failed.
Any idea what I can do to get this working? I have my eyes set on this phone upgrade and will not rest until I get it working xD

Have you tried this?
http://forum.xda-developers.com/showthread.php?p=20850052
Sent from my SPH-D710BST using xda premium

Yeah thats the guide ive been following but it talks about the incognigto. I tried the same steps for my rush, but I cant get my cdma workshop to read my phone, only connect to it.

Cortal said:
Ok I have gone through several guides, trying to get this to work. All guides mention using the incognito, but that cant possibly be the only phone that works.
I have the Galaxy Rush, Boost Mobile, 3g. I know it wont support 4g. I just want a nicer phone and happened to have teh E4GT.
I have the tools from the various incognito guides, and I get stuck at the step where I get CDMA Workshop to read my phone. I connect, I dial ##DIAG# and enter my MSL, then connect and click read. I get a failed message. Since I know my MSL already, I try skipping ahead to getting the NV items, using the MSL as the SPL and get failed.
Any idea what I can do to get this working? I have my eyes set on this phone upgrade and will not rest until I get it working xD
Click to expand...
Click to collapse
I'm Also Trying to find a way to access the NV items on my galaxy rush and any help would be much appreciated. So far ive gotten my MSL/SPC and connected using cdmaworkshop, but one thing I noticed is even after I send the MSL/SPC the NV items containing the AAA/HA passwords always say access denied. and the galaxy rush doesnt unlock with the default samsung password. Im not familiar with using QXDM to know how to connect it to the phone, but I think thats the direction we need to go to find our HA/AAA passwords

any luck with reading ha aaa?

yeah any progress would be extremely helpful