Related
Hi, has anyone replaced their digitizer on their desire z/g2? How did it go? It looks easy on the youtube vid.. have any problems? What way did you use to melt the glue? What digitizer did you use, where from?
Any info much appriciated as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Thanks..
Sent from my HTC Vision using XDA App
Never done it on a g2 but should be pretty straight forward especially with a video lol. Use a heat gun to melt the glue, pretty much the only tool you SHOULD use to do something like that.
I replaced the digitizer on my third G2 after getting a refurb replacement from T-Mobile that had a black spot inside the actual digitizer glass, not on the outside or inside.
The process is very easy with the video, however, trying to keep dust and fingerprints from getting on the inside of the phone while you're trying to get it back together is a serious pain in the rear! If it's the same video that I watched, just use a hair drier blowing hot air to heat the adhesive on the inside of the digitizer and then pop the digitizer off very very slowly, because you don't want to accidentally bend the metal bezel around the screen.
You also may want to leave the original leftover adhesive on the inside, because when I cleaned mine off, light now always leaks out around the bottom edge of the digitizer, below the menu, home, and search buttons, even though I used the double sided adhesive strips covering the entire length of the bottom, so light shouldn't technically be leaking out. No biggie, though... it works like brand new, now!
Thanks for the reply.. I have seen that video and that's what I was using as a guide.. I ordered the digi today, should be here tomorrow.. the only thing I was wondering was the glueing process, as I have not ordered the double sided glue/tape stuff, as I was just hopeing to still use the original glue as I think you are saying.. I hope that works! Have to be careful like u say with dust/fingerprints etc..
Sent from my HTC Vision using XDA App
Hmm, after reading your post again, maybee I should of bought the double sided tape afterall? Do you think the old leftover glue is enough for the new digi?
Many thanks..
Sent from my HTC Vision usingall XDA App
Run over to radio shack they must have some kind of glue you can use lol. google cell phone screen glue see what info you can find.
Ok, just incase anyone is interested, got my new digitizer, followed the video, used a heat gun cerfully to melt the glue, pulled the old digitizer out, and used the original glue whilst still warm to hold the new digi in, as all of glue stayed on the case rather than on the digi, which was pretty lucky.. put it all back together and everything perfect, touchscreen back to how it should be.. cost me 17 pounds.
Sent from my HTC Vision using XDA App
How was this accompilshed?
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
So which digitizer did you end up buying and which guide or video did you follow? I am about to tear mine apart and could use the info.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
Hi, I did buy mine from amazon.co.uk, there were a few for sale,, the one I bought was supposed to be a genuine t-mobile g2 replacement (refurb I think, pressumably this just means that it was from a second hand g2 that had problems and the digi was taken out - and I'm pretty certain this is the case as mine has a thin film (which u leave on) over the back of the digi covering the tracks etc, which had a few very small air/dust bubbles under it (just noticeable when screen off), where I own a desire z, so now it sais t-mobile instead of htc, but I can live with that.
The small grey bits that you talk about were floating about or stuck on my digi when I pulled it off the main chassis. I had a look, and as far as I could work out, were possibly just for giving colour to the tiny led's that give you light to the home/search keys etc (I may be wrong on their use), but if you look closely, the tiny grey things have even smaller rectangles on them that relate to the positions of the led's on the circuit board. So I picked the remaining ones off the old digi, put them back in their correct holes and stuck the new digi in. I've had no problems (with a digi from amazon with no little grey things on it) so far, but maybee this is due to mine being a second hand original part..
Edit : Now after reading your post again, you're talking about bits that are actually on the digi itself, not the white caps that I'm talking about! Whoops. I didn't notice any grey spots on the digi itself, but I guess I must have them..
Sent from my HTC Vision using XDA App
ian577416 said:
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
Click to expand...
Click to collapse
I rekon u replaced the wrong thing! Maybe the lcd?
Sent from my HTC Vision using XDA App
i just replaced mine with this one:
http://www.ebay.de/itm/230685692541?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
actually it says HTC on it and looks a lil bit differently than on the picture.
never the less, i replaced it really carefully and checked every connecting.
But somehow the Touchscreen doesn't work at all.
Can anyone help me ? what could be the problem ?
Wrong digitzer ?
is it okay, that the digitizer has direct contact to the frame where it is glued to ?
jmpcrx said:
... as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Hi!
I have the same problem, I have asked it already here
So you had invisible finger press in the screen, and the screen was bad responsive?
...Just to make sure my problem is digitizer problem! The service wont change it in warranty unless the problem is there all the time! But its driving me crazy! why is it happening randomly, why isnt it all the time? How could i make the screen to do this problem when i'm at the service?
Hi.
my question says it all.
i have a perfect galaxy nexus screen. no weird grid. no weird uneven colors. nothing. just perfect. however, i have few scratches by mistake on the screen " digitizer it self "
is it possible to replace the digitizer without replacing the screen ? money isnt an issue even if its the price of a new phone. its just i have OCD and i do like my screen perfect.
so . is it possible to replace the digitizer alone ? " even if i have to buy them both lcd screen and digitizer ", i will keep the new screen extra for future
I don't think the digitizer is up for sell separately yet.
Sent from my Galaxy Nexus using XDA App
Smokeey said:
I don't think the digitizer is up for sell separately yet.
Sent from my Galaxy Nexus using XDA App
Click to expand...
Click to collapse
thats fine BUT if i buy the sceen and the digitizer, can someone seperate them and install the digitizer on another screen ?
ll_l_x_l_ll said:
thats fine BUT if i buy the sceen and the digitizer, can someone seperate them and install the digitizer on another screen ?
Click to expand...
Click to collapse
I've read that the glass is fused to the housing and display but I'm interested in this as well as I have a spec of dust under my screen.
Sent from my Galaxy Nexus using xda premium
ll_l_x_l_ll said:
Hi.
my question says it all.
i have a perfect galaxy nexus screen. no weird grid. no weird uneven colors. nothing. just perfect. however, i have few scratches by mistake on the screen " digitizer it self "
is it possible to replace the digitizer without replacing the screen ? money isnt an issue even if its the price of a new phone. its just i have OCD and i do like my screen perfect.
so . is it possible to replace the digitizer alone ? " even if i have to buy them both lcd screen and digitizer ", i will keep the new screen extra for future
Click to expand...
Click to collapse
I'm unable to post links yet, so go to iFixit and search for "Galaxy Nexus teardown". Seems the screen and digitizer are fused together, sorry
ll_l_x_l_ll said:
...money isnt an issue even if its the price of a new phone...
Click to expand...
Click to collapse
Buy a new phone, keep other as a backup/media device?
zeekiz said:
Buy a new phone, keep other as a backup/media device?
Click to expand...
Click to collapse
like i said, i am OCD. i go buy new one, i will look for dead pixels/ un even colored screen/ stupid grid that shows weird lines in weird positions of the screen. its like hell for me to go through all that again.
firephoenix1985 said:
I'm unable to post links yet, so go to iFixit and search for "Galaxy Nexus teardown". Seems the screen and digitizer are fused together, sorry
Click to expand...
Click to collapse
i did go to that site before you post it. thanks for trying to help. however i am just wondering that even if they are fused together, can i still take them apart ?
i really dont want to lose that screen
Hopefully the overall quality will improve with the samoled displays in the near future and buying a replacement housing/digitizer will almost guarantie you a good result (dont hold me to it though, just wishfull thinking).. i have some micro scratching aswell (seems to be a normal problem with this device) but only really visable under a really strong super-led flashlight. I'm starting to feel ok with it however and decided to wait with getting a replacement till the price has gone down.
Sent from my Galaxy Nexus using xda premium
I read that one of the members here used a blow dryer on the screen and used a suction cup to remove the screen on their Galaxy S II. If these two devices were constructed similarly then this method may have some merit.
Sent from my Galaxy Nexus using xda premium
the "super" in super amoled means the digitizer and screen are fused together.
i dropped my phone from about 3 feet and broke under my screen but not the screen itself can anyone recommend a good company to buy these parts from??
There's a guy from HK selling it on eBay here. However that means that you'd need to change it yourself. I have looked at the ifixit website about the assembly of the device; however it depends on how comfortable each one is with changing it themselves.
It is quite expensive as well... I will still get a quote from Samsung prior to venturing with this option.
---------- Post added at 09:23 AM ---------- Previous post was at 09:15 AM ----------
To the OP
Where are you getting the digitizer from? If it is sold as fused with the screen, then there's not much trying to tear the combo apart and getting it to look like a machine job will be a challenge. I assume you'd need to build a clean room setup somehow...
Anyways you could possibly verify if the screen quality is to your standards with the eBay seller I mentioned above and buy on that arrangement; however getting the other side to agree/be honest may not be easy.
Instead, why not buy the best screen protector? Those wet ones you get nowadays. Not only will it get rid of the scratches but will also protect your phone for a long time...I think that is a better cheaper investment unless you are sitting on a pile of....cash...
Tjotte said:
Hopefully the overall quality will improve with the samoled displays in the near future and buying a replacement housing/digitizer will almost guarantie you a good result (dont hold me to it though, just wishfull thinking).. i have some micro scratching aswell (seems to be a normal problem with this device) but only really visable under a really strong super-led flashlight. I'm starting to feel ok with it however and decided to wait with getting a replacement till the price has gone down.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I have since this post received 2 more scratches and both is showing quite easy with screen off in normal lighting, last one i got today and that oneĀ“s really bugging me since it looks like something rubbed against the screen a few times.. I always.. always always! only keep my phone in my pocket on my jacket with a plastic zipper and only a microfiber cloth goes in the same pocket.. digitizer actually feels weaker then my old X10's which (apart from that i dropped it and cracked a corner a month before getting the GN) looks rather good to have been tossed around and been riding my workpants which has been everything BUT clean.. a few deep scratches but 18 months of abuse, i'd say it's in good condition! I refuse to put a screenprotector on this phone, initially i did get one.. that one scratched during installation using a regular creditcard and it just looked terrible with the peeling around the edges so, no more protectors.... and i (along with other here at the forum) believe that it is not actually the glass that scratches but rather the oleophobic coating getting scratches.. because the scratches are really really thin but clearly visible.. it's a shame.. but when the next scratch comes, i'm gonna stop being anal about it and just toss it in my right jeans pocket where the phones usually go.. never in my workpants though.. that would kill the coating in a day.
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I remember seeing that thread as well, I tried to find it, but could not.
justbecuz123 said:
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
Click to expand...
Click to collapse
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
707BeastMode707 said:
I remember seeing that thread as well, I tried to find it, but could not.
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Are we talking about the glass or the whole display? It makes a big difference. Assuming all 3 displays are the same (i9250, L700, I515), the problem is separating the display from the frame plate. Its very difficult and you can crack it very, very easily if you try to remove it. The cheaper GN LCD's on eBay are from working units and those already have the frame plate attached to it. The only way to remove it is to use a heat gun and apply it on the top and bottom front areas (as well as the sides). The apply heat to the back frame plate to loosen up the adhesive in the mid section of the screen. Then, slowly and I mean very, very slowly try to pry it open using a thin blade. Start from the top and work your way down. You should stop if you meet too much resistance and reapply heat. Like I said its a pain in the ass and not for the timid. I got to successfully remove an LCD from a frame for a Galaxy S (i500) not too long ago, its a similar in process as the GNex
I also tried to remove a L700 LCD (cracked glass) from a frame a while back and cracked it even more. I know what I did wrong and I think I wont make that mistake again. My mistake was that I did not know the exact location of the adhesive and applied too much heat in the front. Another mistake was that I thought I could remove the front glass from the digitizer. Now I know this is almost impossible and I don't know how people can buy front lenses without using some type of special tools (a true hot air bga station for instance) or a technique that I'm not aware of.
So, that's my long rant right there. I would really appreciate if any of you can confirm that any all 3 displays are the same (i9250, l700, i515). If it is then I would dare to try it out and take some pictures in the process if all goes well.
What about the oven?
I used to be into cars, and it was popular to smoke the headlamps on Nissans. They also have a lot of glue in them, and it was recommended to put em in an oven lol.
I'm sure it would get hot enough to loosen the screen, but 400 degrees may break something else in the process...
Sent from my Galaxy Nexus using xda premium
Did anyone ever find the answer to this question? I am wondering the same thing.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
You can't use the i9250 screen on the i515. The battery metal thingies and the vibration thing are in different places.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
I have asked a bunch of eBay sellers for the last few days and have gotten mixed responses... I don't think that most of them get that I am talking about separating the display from the front case/plate. One guy told me that the digitizer/LCD combo is interchangeable from the i515 and i9250, but it won't work on the L700. One guy told me that he thought that the entire assembly including the front plate were the same between the L700 and i515. Several have said that they are model specific, but I don't think that most of them realized that I am not expecting to use the front plate from an L700 if i9250 on the i515...
It doesn't seem like Samsung would have a different display for each model. I can see the plates and cases being different because some of the other parts are different, but it seems like the LCD panel and the glass should be the same for each model. To me all of the screen connectors look the same from the pics I've seen...
Edit- I just found this online store that indicates they are the same screens http://www.globaldirectparts.com/OEM-Galaxy-Nexus-L700-LCD-Digitizer-Assembly-p/smsng6115350-qs.htm
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post.
Click to expand...
Click to collapse
Finally found the post that you are referring to (http://forum.xda-developers.com/showthread.php?t=1780491). Sounds like he ran into problems because he tried to use the i515's front housing on the i9250. I think if he had removed the screen from the frame and re-used the frame that was original to his phone he would have been fine. It looks like it takes some heat and care to do that, but it looks do able.
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
MrAreCool said:
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
Click to expand...
Click to collapse
L700 screen (not including frame) worked on my i515. Details here.
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
perusmuro said:
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
Click to expand...
Click to collapse
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
MrAreCool said:
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
Click to expand...
Click to collapse
I have found few videos where that glass is possible to remove.
http://www.youtube.com/watch?v=JlfO6TUj1DQ
But I think that I would buy that whole set and change that. But what is the best place to buy that? So I can real deal.
Ok guys, just wanted to confirm that front glass for the L700 and GT-i9250 the same. And I assume that i515 as well.
I got for repair Nexus Sprint (L700) with cracked front glass but then was surprised that glass for L700 on ebay about $15 and the same glass for i9250 less then $10. Not big deal but anyway.. So I bought the glass for i9250 and it fits great as original.
Good luck!)
When the purchase of parts and mobile phones are not matched, the proposed replacement.
Hey guys. My wife just broke her gs3. She lost it in the snow on some stairs and while looking for it it fell off the side of the stairs and dropped about 6 ft onto concrete. I have an otterbox defender case for her but no matter how much I tell her to put it om she rarely does. Needless to say, I am less than thrilled. So.... the phone turns on and the capacitive buttons light up, she can hear notifications but the screen is black. Looks fine until close inspection but then you can see a small crack under the glass (im assuming its the lcd panel.) So how can I fix this? I am fairly good at taking stuff like this apart as im always working on radios, tv's, and other electronics at work.
Search here or youtube there is a vid with step by step on replacing the gorilla glass and im not sure if that includee the digitizer or not.
My sister cracked that screen underneath too. She took it into Sprint and they said there was no way they could replace it, because its not the glass on top, its the one underneath
She had to activate her old OG EVO and is just stuck waiting for her next upgrade now.
Sent from my PG06100
Please read forum rules before posting
Questions and help issues go in Q&A
Thread Moved
Thank you for your cooperation
Friendly Neighborhood Moderator
Same thing happened to me a couple months ago, yeah Sprint said they couldn't fix it, I had to pay for a new one, even with full insurance. Honestly I'd just try searching eBay or something for a Samsung Galaxy S3 OLED panel, and YouTube for instructions. I wish you luck sir!
Sent from my SPH-L710 using Tapatalk 2
BDawgTrap said:
Hey guys. My wife just broke her gs3. She lost it in the snow on some stairs and while looking for it it fell off the side of the stairs and dropped about 6 ft onto concrete. I have an otterbox defender case for her but no matter how much I tell her to put it om she rarely does. Needless to say, I am less than thrilled. So.... the phone turns on and the capacitive buttons light up, she can hear notifications but the screen is black. Looks fine until close inspection but then you can see a small crack under the glass (im assuming its the lcd panel.) So how can I fix this? I am fairly good at taking stuff like this apart as im always working on radios, tv's, and other electronics at work.
Click to expand...
Click to collapse
You would need to replace the screen and the LCD which i believe are sold seperatly but have been known to be prone to issues if you don't purchase them together that being said it will cost you around 70-80 to replace yourself and sprint WILL replace the screen you just have to pay around 100-150 for the new screen and installation
Sent from my SPH-L710 using xda app-developers app
jazz995756 said:
You would need to replace the screen and the LCD which i believe are sold seperatly but have been known to be prone to issues if you don't purchase them together that being said it will cost you around 70-80 to replace yourself and sprint WILL replace the screen you just have to pay around 100-150 for the new screen and installation
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
It's not the screen that's cracked, it's only the LCD (actually an OLED screen). Trust me I went to the corporate Sprint store by me in NYC and they said they could not fix it, they could only replace the front glass screen.
like everyone said its the digitizer underneith, theres a guy on you tube, name is L35505 or L3SSONS or some stuff. he does a FULL replacement i think. will help you alot. be careful, take a saterday, kick out the kids and everyone and you shouldnt have any problems
http://www.youtube.com/watch?v=_70-W9JjVjg
but watch this one first http://www.youtube.com/watch?v=zs8NVl74uYs haha i about died laughing.
same here
BDawgTrap said:
Hey guys. My wife just broke her gs3. She lost it in the snow on some stairs and while looking for it it fell off the side of the stairs and dropped about 6 ft onto concrete. I have an otterbox defender case for her but no matter how much I tell her to put it om she rarely does. Needless to say, I am less than thrilled. So.... the phone turns on and the capacitive buttons light up, she can hear notifications but the screen is black. Looks fine until close inspection but then you can see a small crack under the glass (im assuming its the lcd panel.) So how can I fix this? I am fairly good at taking stuff like this apart as im always working on radios, tv's, and other electronics at work.
Click to expand...
Click to collapse
Same happened to my galaxy s3, it was still on after it broke but when i plug it in the screen went off, even with the screen blank was still working
---------- Post added at 09:34 PM ---------- Previous post was at 09:32 PM ----------
BDawgTrap said:
Hey guys. My wife just broke her gs3. She lost it in the snow on some stairs and while looking for it it fell off the side of the stairs and dropped about 6 ft onto concrete. I have an otterbox defender case for her but no matter how much I tell her to put it om she rarely does. Needless to say, I am less than thrilled. So.... the phone turns on and the capacitive buttons light up, she can hear notifications but the screen is black. Looks fine until close inspection but then you can see a small crack under the glass (im assuming its the lcd panel.) So how can I fix this? I am fairly good at taking stuff like this apart as im always working on radios, tv's, and other electronics at work.
Click to expand...
Click to collapse
Please help, what can I do
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
May i ask how you replaced the glass, and where you bought it? Shattered mine couple of days ago...
Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
My English is not my native language, but considering the word adhesive, you must referring to the double side tape part that holds the digitizer and the glass together.
Assuming that, from my own experience it is a no-go. If you are experiencing sticking parts (ie. it's not properly glued) I am afraid you might have to replace the whole adhesive.
I had the same issue on my Desire HD and about 1 month after replacement, same as you kept pushing it to take the haze away, the inevitable happened. A tiny opening not being able to see with the naked eye, left enough room for dust to enter under the glass. One month later, there was so much dust in it that I had to buy a new full screen.
However, months later, I tried some old trick for future experiments You can eventually take a paint dryer, and try to heat up the lose part then applying some light pressure onit. This process should make the glue on the adhesive very soft and with a bit of luck it might stick on the glass.
I'd say perhaps 60-70 degrees. Don't worry, even 100 degrees won't break your screen unless u're heating it up for more than 10 minutes or so
GL
Fantastic, I'll give heat a try to get it to stick. Unfortunately I can't find the double sided tape anywhere otherwise I'd replace it. I'm in Australia so shipping is pretty expensive from most places outside of the country. I really appreciate the reply
I bought the glass alone off eBay, I believe it was around $30. To replace it took a lot of patience, a hairdryer on low for 15 mins to heat the glue up, finding a spot to slowly pry the glass away from the LCD. As I said, a lot of patience and a lot of mess since my screen was badly cracked and kept breaking off. Was worth it to save $300 though. Figured I could do it for $30 myself and if it broke I'd have had to of paid for both either way
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order
matzone said:
It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order
Click to expand...
Click to collapse
Im from the netherlands too, which shops do you recommend? I bought my phone at coolblue, but I dont want to lose my phone for 2 weeks with repair..
Sent from my GT-N7100 using xda app-developers app
Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
Check out the link in my signature. You'll find what you're looking for with regards to the adhesive.
Sent from my GT-N7100 using xda premium