I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
May i ask how you replaced the glass, and where you bought it? Shattered mine couple of days ago...
Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
My English is not my native language, but considering the word adhesive, you must referring to the double side tape part that holds the digitizer and the glass together.
Assuming that, from my own experience it is a no-go. If you are experiencing sticking parts (ie. it's not properly glued) I am afraid you might have to replace the whole adhesive.
I had the same issue on my Desire HD and about 1 month after replacement, same as you kept pushing it to take the haze away, the inevitable happened. A tiny opening not being able to see with the naked eye, left enough room for dust to enter under the glass. One month later, there was so much dust in it that I had to buy a new full screen.
However, months later, I tried some old trick for future experiments You can eventually take a paint dryer, and try to heat up the lose part then applying some light pressure onit. This process should make the glue on the adhesive very soft and with a bit of luck it might stick on the glass.
I'd say perhaps 60-70 degrees. Don't worry, even 100 degrees won't break your screen unless u're heating it up for more than 10 minutes or so
GL
Fantastic, I'll give heat a try to get it to stick. Unfortunately I can't find the double sided tape anywhere otherwise I'd replace it. I'm in Australia so shipping is pretty expensive from most places outside of the country. I really appreciate the reply
I bought the glass alone off eBay, I believe it was around $30. To replace it took a lot of patience, a hairdryer on low for 15 mins to heat the glue up, finding a spot to slowly pry the glass away from the LCD. As I said, a lot of patience and a lot of mess since my screen was badly cracked and kept breaking off. Was worth it to save $300 though. Figured I could do it for $30 myself and if it broke I'd have had to of paid for both either way
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order
matzone said:
It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order
Click to expand...
Click to collapse
Im from the netherlands too, which shops do you recommend? I bought my phone at coolblue, but I dont want to lose my phone for 2 weeks with repair..
Sent from my GT-N7100 using xda app-developers app
Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
Check out the link in my signature. You'll find what you're looking for with regards to the adhesive.
Sent from my GT-N7100 using xda premium
Related
My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Dillsnik said:
My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Click to expand...
Click to collapse
I am no expert, but it would seem that if anything under the glass was broken, you would need to replace the lcd (that is, if you could see the lcd "leaking" or being distorted)
Sent from my ARCHOS 80G9 using Tapatalk 2
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Dillsnik said:
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Click to expand...
Click to collapse
Unfortunately I have had the pleasure of replacing my digitizer twice. You definitely wanna buy it WITH the frame or housing. The adhesive is like industrial strength and you will end up breaking the original anyways when trying to remove the digitizer from it. I have to warn you that doing this repair yourself will void your warranty. Make sure the digitizer you get comes with the tools required to get the phone apart. You can get this as a package on eBay fairly cheap too. There are about 3-4 circuit strips that will have to be removed from their clips, don't be intimidated by them, but be gentle. Your first time is gonna take you a while, just be patient. If you need to do it a second time, its gonna be a breeze. PM me if you have any concerns during your repair.
yea get a digitizer also,
I had the same thing happen to me, it was a pain but there are a few videos on youtube
that should help you through it, though it doesn't sound like its that bad
Definitely go with the digitizer and housing replacement together. Bottom line, it will make your life so much less of a headache while replacing it.
Sent from my ADR6300 using XDA
I just replaced mine this weekend. I attached some before, during, and after pictures...
These were the guides that I followed:
Part 1: http://www.youtube.com/watch?v=TfpPS7oO4Q8
Part 2: http://www.youtube.com/watch?v=GJMAmKpk20c
Personally, I went with just the glass/digitizer (your first link) and it went fine. The glass is difficult to get out of the housing, but it's not that bad. It probably took me 20 minutes to get the old glass out, maybe 5 minutes of cleaning goo from the old adhesive, and probably another 5 minutes to put the new glass back on.
Some Tips:
The pry tool that comes with it is very cheap. I would suggest using it sparingly until you get to the LCD panel extraction and glass removal. You want it to be as in good of condition as can be when you get to those later steps.
Use a blow-drier to heat up the adhesive, and get it to the point where you almost cant touch it. I used some yellow kitchen gloves so I could get it a little hotter and still be able to hold it. I used a combination of my hands and the pry tool and worked mostly along the sides and top first, then separated the bottom last.
The guy in the youtube videos uses glue, but you shouldn't need that. It comes with pre-cut adhesive strips, which work great. One word of caution though... The sheet that they come on is scored for you, but I suggest using an x-acto to cut them out. This is especially important for the thin rectangle that goes around the outside of the glass. You really don't want to pull on that... you don't want it to get stretched or twisted. Summary: the strips work great, just be careful extracting them from the sheet they come on, and placing them on the phone.
Don't forget to get the red earpiece grill off of the old glass before throwing it away. You'll need to super glue that back onto the housing, but it's really easy to see where it goes. This should be the only thing you need glue for.
When removing the glass, cleaning up gunk from the old adhesive, and applying new adhesive, be careful of the electronics at the bottom for your capacitive buttons... you definitely don't want to harm or obstruct those.
This should probably go without saying, but make sure not to touch the inside of the new glass, or the LCD panel. You don't want fingerprints or dust inside the phone. Even if you don't touch it, I would still give it a shot of compressed air right before putting it in, just to make sure there's no dust.
I would say that it's probably worth the extra $10-12 bucks to get it with the housing already included, but it's definitely not necessary if you want to save a little money. As I said above, it only took me about a half hour to get the old glass out and the new glass in, and from what it sounds like, there is still some effort involved even if you get it with the housing (moving the circuitry from the old one). I wouldn't worry about breaking the frame... it's pretty strong. If you break it, you're doing it wrong. Although, if your frame has some scrapes and other assorted road rash on it like mine does (see first picture), then maybe you might want a new one anyway. Another consideration... the reviews on Amazon for the one without the housing are much better, but that could just be because of people who don't know what they're doing... who knows.
If you have any questions, I'd certainly be willing to help... PM me if you want. And if I'm going to be around when you go to actually do the replacement, I can give you my gchat address in case you have any questions during the process.
Guys
I observed that there is a crack in the benzel of my sgs2. Benzel i mean The plastic lining that wraps around the front glass.
The crack is near the volume buttons.
How easy it is to replace this plastic strip ? Is it risky ?
Sent from my GT-I9100 using Tapatalk
Pretty sure you mean bezel, not benzel.
You would probably have to replace the entire housing which is quite risky to do in my opinion. If you don't know what you are doing you could short the board or break something.
Happened to me too.
Is it really so bad that you need to replace it?
Happend to me too. Seems like that part is very fragile.
I think the only way you can replace it is replacing the whole screen and touch panel.
After that one little crack and that mysterious burn mark right next to it (damn alcohol ) i finally decided to buy a case
TheSniperFan said:
Happened to me too.
Is it really so bad that you need to replace it?
Click to expand...
Click to collapse
Its not so bad. But there is an another minor crack on the exactly other side of the benzel where power button is present !
Is it because of overheat ? I use my phone while charging and battery temps are at 46 celcius when I do that.
I never dropped my phone.
If I go for a new benzel then will I have to pay for new screen too ? Is the benzel glued to the screen ?
Sent from my GT-I9100 using Tapatalk
DaPhinc said:
Happend to me too. Seems like that part is very fragile.
I think the only way you can replace it is replacing the whole screen and touch panel.
After that one little crack and that mysterious burn mark right next to it (damn alcohol ) i finally decided to buy a case
Click to expand...
Click to collapse
Buying a case is not an option for me. I nvr dropped my phone. I use it very carefully , I love my sgs2.
Why would I have to replace screen also ?
Sent from my GT-I9100 using Tapatalk
You can probably have it replaced at an official Samsung repair center. I'm pretty sure they carry one or two sets -- or can order one for you -- but it'll probably set you back a little.
sachinaik said:
Why would I have to replace screen also ?
Click to expand...
Click to collapse
I am not sure about this. But looking at the screen replacement tutorial (http://forum.xda-developers.com/showthread.php?t=1253969) it seems like screen+touchpanel+bezel is a single part. I guess it is somehow glued together. But again, that is just a guess.
just put a little glue in the crack
went to samsung service center.
They said they will replace the Glass panel, Pled screen and benzel.
Oh what the hell, I'll get a new Oled screen. Will go for SGS4 directly
Sent from my GT-I9100 using Tapatalk
I guess it is not covered by warranty, is it? How much do they charge you for replacing it?
DaPhinc said:
I guess it is not covered by warranty, is it? How much do they charge you for replacing it?
Click to expand...
Click to collapse
Approximate 6000Rs I.e, 120$
Sent from my GT-I9100 using Tapatalk
yeah I noticed a crack on my bezel above the volume button. You can kind of see it on the enclosed picture.
I've got a crack in almost exactly the same place as the above pic, slightly closer to the top of the volume button.
Mine has been in an official flip case since day one and has never been dropped. I only noticed the crack when I looked after reading this thread (just like the plastic cover over the home button thread!).
I wouldn't have noticed the crack because of the case. So, is this a design fault? Is it heat or flex that is causing the crack?
The benzel is the most fragile part I think.
I must be because of heat. As the processor, gpu and antenna are near camera module. The top portion gets a lot hotter when accessing 3G.
On top of that if any pressure you put on it going to worsen it. Putting it in a tight jeans and then when u try to remove it out of pocket, u tend to grab the benzel a lot.
All in all, I would go for a metal/polycorbonate benzel in my next phone. That disqualifies SGS3.
Obviously I dont want to pay a hell lot of amount just to get a thin plastic strip (benzel) to be replaced.
Just because samsung did stupid move to glue them together and chose a cheap plastic for benzel I now have to pay a lot.
Waiting for HTC One XL(unibody) with S4 chipset. At least it would come for 3 yrs rather than breaking within 11 Months.
End of rant. Sh**ty cheap plastic Samsung.
Sent from my GT-I9100 using Tapatalk
same issue for me
i discovered that few weeks after buying the device
i kept the device with that crack but i worried about it
"happy" to see that i'm not the only one
Incredible! Saw this thread and wondered what the hell a 'benzel' was. After reading that it had happened to more people, I just checked my phone and it has the same crack.
Had never noticed this until now. Fortunately mine is a black phone, so not as noticeable as the white.
check my post open in may
http://forum.xda-developers.com/showthread.php?p=13714534#post13714534
Wow i had one also at the power button side, i thought it os scratch first but not. Interesting how could this be happen
Sent from my GT-I9100 using XDA
sachinaik said:
Just because samsung did stupid move to glue them together and chose a cheap plastic for benzel I now have to pay a lot.
Waiting for HTC One XL(unibody) with S4 chipset. At least it would come for 3 yrs rather than breaking within 11 Months.
End of rant. Sh**ty cheap plastic Samsung.
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
the phone isnt exactly broke though is it?? a part of the phone could have been designed better maybe but it isnt broke and doesnt stop he phone from working its also very hardly noticeable
ive had one sgs2 for around a year now and used it hard and it works great
oh and watch these videos and then try and say the sgs2 wont last 3 years if looked after properly
http://www.youtube.com/watch?v=nXOezJKpOsg
http://www.youtube.com/watch?v=uFKmvJ0zIiY
also the bezel scratches easy is there any point in replacing it when you could pay to have it fixed then drop the phone or scratch it against something??
wear marks are never good to see but they do happend
Ive never dropped a cellphone but today was that day. I had bought an invisible shield to put it on today when i got home. Right when i got home i put the phone in my pocket but it had it had hole. BAM. it dropped down my leg and hit the concrete face down. It shattered the digitizer but the lcd is intact. My question was, would i be able to buy a digitizer and change it without having to pay 180 for a new digitizer/lcd ? any help would be appreciated.
Sent from my SGH-T999 using xda app-developers app
I'm fairly sure I've read that the digitizer is fused with the screen.
Yeah there's no way going around it. They're glued together as one piece.
FFFFFFFUUUUUUUU dammit
Sent from my SGH-T999 using xda app-developers app
I spoke to some rep from samsung yesterday on my phone and they said it would be 179.99 to fix it. But my question is, do i have to include the lcd ? Because my lcd isnt broke and they sell the glass on ebay for 20 bucks. I would rather try and fix it myself and break it, THEN send it to samsung if i cant fix it instead of paying 180 bucks for just some glass since my lcd is not broken and have them rip me off because they will def reuse my lcd and win anyways.
kobe4rings said:
I spoke to some rep from samsung yesterday on my phone and they said it would be 179.99 to fix it. But my question is, do i have to include the lcd ? Because my lcd isnt broke and they sell the glass on ebay for 20 bucks. I would rather try and fix it myself and break it, THEN send it to samsung if i cant fix it instead of paying 180 bucks for just some glass since my lcd is not broken and have them rip me off because they will def reuse my lcd and win anyways.
Click to expand...
Click to collapse
It's been answered.. if you want to do it yourself you're going to end up breaking your LCD and need to buy the part or send it to Samsung anyways. There is no way around it.
There is a video on YouTube with somebody changing only the glass. Check on YouTube so you will have an idea about how to do it and if you will be able.
Sent from my GT-I9300 using Tapatalk 2
I dont believe they are "fused" together. from my history in repairing phones, there is just a small sliver of double sided tape holding the digitizer to the LCD screen. and all you need to do is use a plastic seperating tool to slowly seperate the two. Also, use a good hot hair dryer to help melt away the adhesive. good luck!
Go to a hardware store and pick up a heat gun. Take the phone completely apart, take out all the electronics. Heat the screen evenly and slowly start pulling the screen up little by little while hitting it with the heat gun.
Take your time and don't rush. It can be done but it's not easy and can damage the LCD.
Sent from my SGH-T999 using Tapatalk 2
If you do this HEAT the **** out of the LCD and digitizer. It will be very hard to separate the two. Please take pictures and tell us you're approach to help other S3 users.
I had a long ass post written but now it's gone. boo.
anyways. Here's something to consider as to why you can't separate it. If you believe there's a way to get around it then good luck.
http://www.youtube.com/watch?v=es8gezSdKv4&feature=youtu.be
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I remember seeing that thread as well, I tried to find it, but could not.
justbecuz123 said:
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
Click to expand...
Click to collapse
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
707BeastMode707 said:
I remember seeing that thread as well, I tried to find it, but could not.
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Are we talking about the glass or the whole display? It makes a big difference. Assuming all 3 displays are the same (i9250, L700, I515), the problem is separating the display from the frame plate. Its very difficult and you can crack it very, very easily if you try to remove it. The cheaper GN LCD's on eBay are from working units and those already have the frame plate attached to it. The only way to remove it is to use a heat gun and apply it on the top and bottom front areas (as well as the sides). The apply heat to the back frame plate to loosen up the adhesive in the mid section of the screen. Then, slowly and I mean very, very slowly try to pry it open using a thin blade. Start from the top and work your way down. You should stop if you meet too much resistance and reapply heat. Like I said its a pain in the ass and not for the timid. I got to successfully remove an LCD from a frame for a Galaxy S (i500) not too long ago, its a similar in process as the GNex
I also tried to remove a L700 LCD (cracked glass) from a frame a while back and cracked it even more. I know what I did wrong and I think I wont make that mistake again. My mistake was that I did not know the exact location of the adhesive and applied too much heat in the front. Another mistake was that I thought I could remove the front glass from the digitizer. Now I know this is almost impossible and I don't know how people can buy front lenses without using some type of special tools (a true hot air bga station for instance) or a technique that I'm not aware of.
So, that's my long rant right there. I would really appreciate if any of you can confirm that any all 3 displays are the same (i9250, l700, i515). If it is then I would dare to try it out and take some pictures in the process if all goes well.
What about the oven?
I used to be into cars, and it was popular to smoke the headlamps on Nissans. They also have a lot of glue in them, and it was recommended to put em in an oven lol.
I'm sure it would get hot enough to loosen the screen, but 400 degrees may break something else in the process...
Sent from my Galaxy Nexus using xda premium
Did anyone ever find the answer to this question? I am wondering the same thing.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
You can't use the i9250 screen on the i515. The battery metal thingies and the vibration thing are in different places.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
I have asked a bunch of eBay sellers for the last few days and have gotten mixed responses... I don't think that most of them get that I am talking about separating the display from the front case/plate. One guy told me that the digitizer/LCD combo is interchangeable from the i515 and i9250, but it won't work on the L700. One guy told me that he thought that the entire assembly including the front plate were the same between the L700 and i515. Several have said that they are model specific, but I don't think that most of them realized that I am not expecting to use the front plate from an L700 if i9250 on the i515...
It doesn't seem like Samsung would have a different display for each model. I can see the plates and cases being different because some of the other parts are different, but it seems like the LCD panel and the glass should be the same for each model. To me all of the screen connectors look the same from the pics I've seen...
Edit- I just found this online store that indicates they are the same screens http://www.globaldirectparts.com/OEM-Galaxy-Nexus-L700-LCD-Digitizer-Assembly-p/smsng6115350-qs.htm
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post.
Click to expand...
Click to collapse
Finally found the post that you are referring to (http://forum.xda-developers.com/showthread.php?t=1780491). Sounds like he ran into problems because he tried to use the i515's front housing on the i9250. I think if he had removed the screen from the frame and re-used the frame that was original to his phone he would have been fine. It looks like it takes some heat and care to do that, but it looks do able.
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
MrAreCool said:
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
Click to expand...
Click to collapse
L700 screen (not including frame) worked on my i515. Details here.
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
perusmuro said:
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
Click to expand...
Click to collapse
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
MrAreCool said:
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
Click to expand...
Click to collapse
I have found few videos where that glass is possible to remove.
http://www.youtube.com/watch?v=JlfO6TUj1DQ
But I think that I would buy that whole set and change that. But what is the best place to buy that? So I can real deal.
Ok guys, just wanted to confirm that front glass for the L700 and GT-i9250 the same. And I assume that i515 as well.
I got for repair Nexus Sprint (L700) with cracked front glass but then was surprised that glass for L700 on ebay about $15 and the same glass for i9250 less then $10. Not big deal but anyway.. So I bought the glass for i9250 and it fits great as original.
Good luck!)
When the purchase of parts and mobile phones are not matched, the proposed replacement.
So, I shattered the glass on my Galaxy S3 today. It's pretty messed up (see the attached picture), but the touch works, even in the damaged areas. So it seems it's only the glass that needs to be replaced, with something like this:
http://www.ebay.co.uk/itm/Blue-Fron...K_Replacement_Parts_Tools&hash=item417515ee67
Correct?
Yep, goodluck. Replaced the same on my Galaxy Note 2. all good now.
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
1slow4G said:
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
Click to expand...
Click to collapse
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
MadsBen said:
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
Click to expand...
Click to collapse
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Actually the glass on an s3 is just that, glass. The digitizer is fused together with the LCD. However glass is glued to the LCD which can make it very difficult to replace. If you've never taken on the repair of a screen before then I would say you'll be more likely to break the LCD than not in your replacement of the glass. But again it is possible if you are very slow and very careful. As someone else mentioned though it's much easier to replace the whole assembly.
It didn't went well. I wasn't too carefull. In the bottom, the glass was too shattered, so when I tried to lift it, a piece with glue got stock and lifted the digitizer. So now that don't work. I'm not gonna spend £100-120 on a new digitizer, I'm gonna settle for my good old Nokia 6300i (and Nexus 7...) and wait for the Nexus 5.
I would wait for the n5.. gs3 is a dying trend already.
Its hard like everyone said , if your really gunna do it watch videos online and be prepared. If you know anyone that has done it successfully ask for help or tips
ouch didnt see u tried it already
the same happened to me on my wife's white sgs3 trying to be the savior of the day turned out to be an expensive digitizer replacement of $200 instead of the $8 glass replacement. I rushed the glass removal and cracked the lcd screen. I could have ordered one on ebay for $100 but wife needs the phone the next day so i decided to get it repaired locally.
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
My 2 cents
bidibull14 said:
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
Click to expand...
Click to collapse
Wanted to warn that changing the glass is not for everyone. It takes patience and zen. If you rush it, you will likely break LCD and spend even more $$$ that you would have otherwise. Also following notes:
1. Watch at least a couple of youtube videos before starting.
2. Heavy duty heat blower works much better than a hair dryer. Of course, don't go crazy, as it's possible to melt the phone with it
3. S III has a wire at the bottom (the one which goes to the buttons). If you damage it, you will need to replace whole LCD, there is [almost] no chance you will be able to fix this wire. So, always start removing glass starting with the top of the phone
4. Heavily cracked glass is hard to remove, as it crumbles. To make it easier, a) put a scotch tape on top of glass, so that the small pieces stick to it, and b) use a lot of heat
5. Everybody advises to use plastic tools, personally I used swiss army knife with high level of success, and never had a problem scratching LCD. Your mileage may vary, but using metal blade certainly makes life much easier, especially in heavily cracked glass situation.
6. If you do use blade, it often is enough to get blade just a little bit under a glass, and then simply apply heat. Big chunks will unglue all by themselves.
7. Remember, that failure is always an option. Don't use it on the phone, if you know that you desperately need it working right this day, if you don't have a plan B.
1slow4G said:
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Click to expand...
Click to collapse
same freezing issue on mine... apparently the hardness of Gorilla2 is much greater than the knockoff glass replacements. The replacement glass on ebay and kijiji may not be authentic and that is why it bends slightly when pressed harder (in fact mine cracked completely when I applied too much pressure)
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
hani93 said:
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
Click to expand...
Click to collapse
I've heard about that glue too. I'm considering switching mine, because when I repaired I reused the glue of the original glass, and know I had dust between the glass and the lcd -.-
My concern is about the uv light, don't know if we could put in the sun to substitute it.
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
m1batt1 said:
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
Click to expand...
Click to collapse
it's not that hard to remove factory gle there..
for example, i removed mine, by rolling the glue with fingers.
just make sure, that you don't apply too much pressure to lcd.
and after that, clean up lcd form dust/fingerprints, and you are good to go.
and for removing glass, i used usual/ stronger kitchen knife (attached picture).
i replaced my glass 3 months ago.
i use normal hair dryer to remove glass and glass comes out almost as whole except for small broken pieces.
i think my scratch guard help in that.
i didnt use any additional glue or uv light.
nonresponsive screen is issue but only when you press too hard and press of power button resolve this issue.
but whole process of replacing galss took 2hrs