Requirements
1. Sony Xperia S smartphone.
2. Make sure the smartphone’s bootloader in unlocked. If not, follow the official documentation herehttp://unlockbootloader.sonymobile.com/.
3. Install the device drivers.
4. Download fastboot drivers from herehttp://xperiadev.wordpress.com/guidelines-xperia/flashtool-fastboot/. Extract fastboot.zip into a directory.
5. Backup important data like Apps, SMS’s, Bookmarks, Contact etc.
6. If possible fully charge the phone before proceeding.
How to install CyanogenMod 10 Jelly Bean ROM on Sony Xperia S
1. Download the CyanogenMod 10 based Jelly Bean ROM from the XDA page.
2. Also download the Google Apps Package.
3. Move the files to the root of phone’s SD Card.
4. Extract the kernel.elf/boot.img file from the firmware .zip file to the fastboot directory.
5. Disconnect and Power off the phone.
6. Reboot Xperia S in the fastboot mode by pressing and holding Volume + Power button simultaneously until a blue light on the device comes up.
7. Connect the device to the PC using USB cable and flash it using fastboot. For that open Command*Prompt*from the fastboot directory and execute the following commands
fastboot flash boot kernel.elf/boot.img
fastboot reboot
8. Enter the Recovery Mode by pressing Volume button several times as soon as the FreeXperia logo is shown with an Amber light.
9. From the Recovery Menu choose install zip from SD Card and select the ROM file downloaded and saved to the SD card in step 3.
10. Repeat step 9. This time select the Google Apps Package.
11. Once the installation is finished. Select go back to open the Main Menu.
12. Now select wipe data/factory reset. Confirm it to wipe the data completely.
13. Once the data wipe is complete, select Reboot System Now from the Recovery Menu.
That's it..... You're good to go now.
Sent from my Xperia SL using Tapatalk 2
Look here:
Can I use this on my ICS 4.0?Or I need to be on 4.1.2?
What is the nickname of Xperia S?
X.DragonSlayer.X said:
Can I use this on my ICS 4.0?Or I need to be on 4.1.2?
What is the nickname of Xperia S?
Click to expand...
Click to collapse
NOZOMI
What's about CM10.1??
What was wrong with the instructions given by FXP in the development thread...
FXP said:
HOWTO
Install instructions:
first time
- power off the phone:
- hold vol+ and plug usb to boot into fastboot (blu led)
- fastboot flash boot boot.img (from cm10 zip)
- fastboot reboot
- enter recovery, on boot led will be violet for 3'', during this period press vol+
- flash rom zip
- flash gapps zip
- wipe
- reboot
for update just flash rom zip from recovery
Google Apps are not included in this ROM. You'll need to find those yourself if you want them.
ENJOY AN UNOFFICIAL CM10 RELEASE BROUGHT TO YOU BY FreeXperia Team
PLEASE DONT MIRROR OUR ROMS
Click to expand...
Click to collapse
How about looking up this thread by DooMLoRD on everything you need to know about the xperia S
or any of the guides from this thread. ALL-IN-ONE thread
I am sure that your only trying to help users. However having multiple threads across different phone forums repeating the same information provided by the ROMs developer could be seen as an attempt to pad your stats to apply for a Recognized Contributor.
As talked about here by Pandemic (and others if you read the thread) in your Xperia Neo thread
Pandemic said:
i think yes because he is begging for thanks bro
Click to expand...
Click to collapse
Please search before creating new threads with duplicate information, reported for closing
Thanks
~Jaramie
Thread closed. There is already one which covers the subject.
Not sure if this has been posted already but, this exact process for rooting works for almost ANY android device the program is very easy to use and I will do my best to try and explain how it works.
First, download this ROOTING TOOL
BLU Tank 4.5 Recovery Provided by lopestom: DOWNLOAD
SuperUser: DOWNLOAD
MobileUncle Tools: DOWNLOAD
Now that you have all of these files I will teach you step by step to achieve root + CWM.
ROOTING:
1. Extract the rooting tool to your computer the folder should be called "VROOT" now open the file Root.exe and this image will appear. (MAKE SURE YOUR PHONE IS CONNECTED VIA USB WITH INSTALLED DRIVERS)
2. CLICK ROOT.
The program will install a chinese version of superuser which we will delete after CWM installation. (YOUR PHONE WILL REBOOT, THIS IS NORMAL)
3. After reboot, you may now exit the program.
CWM:
1. Now that we are rooted, we can install CWM. While your phone is still plugged into your computer place the MobileUncleTools.apk into your phones storage.
2. Exract the recovery "BLU Tank 4.5.zip" to your computer and put the recovery image file into your phone.
3. Go to your phone and load the application "File Manager" and install the program MobileUncletools.apk that you just put on your phone.
4. Run the program Mobile Uncle Tools on your phone:
Next:
5. Once you Select the recovery.img your phone will prompt you to flash the recovery, click YES, it will then prompt you to reboot your phone into recovery then choose YES.
6. You should now be in CWM.
NOW TO REMOVE CHINESE SUPERUSER.
1. Choose to install a zip from SD CARD > Choose UPDATE-SuperSU-v1.41.zip > Install
2. CWM will remove chinese SU and you now have Chainfire SU.
Done.
swindillon said:
Not sure if this has been posted already but, this exact process for rooting works for almost ANY android device the program is very easy to use and I will do my best to try and explain how it works.
First, download this ROOTING TOOL
BLU Tank 4.5 Recovery Provided by lopestom: DOWNLOAD
SuperUser: DOWNLOAD
MobileUncle Tools: DOWNLOAD
Now that you have all of these files I will teach you step by step to achieve root + CWM.
ROOTING:
1. Extract the rooting tool to your computer the folder should be called "VROOT" now open the file Root.exe and this image will appear. (MAKE SURE YOUR PHONE IS CONNECTED VIA USB WITH INSTALLED DRIVERS)
2. CLICK ROOT.
The program will install a chinese version of superuser which we will delete after CWM installation. (YOUR PHONE WILL REBOOT, THIS IS NORMAL)
3. After reboot, you may now exit the program.
CWM:
1. Now that we are rooted, we can install CWM. While your phone is still plugged into your computer place the MobileUncleTools.apk into your phones storage.
2. Exract the recovery "BLU Tank 4.5.zip" to your computer and put the recovery image file into your phone.
3. Go to your phone and load the application "File Manager" and install the program MobileUncletools.apk that you just put on your phone.
4. Run the program Mobile Uncle Tools on your phone:
Next:
5. Once you Select the recovery.img your phone will prompt you to flash the recovery, click YES, it will then prompt you to reboot your phone into recovery then choose YES.
6. You should now be in CWM.
NOW TO REMOVE CHINESE SUPERUSER.
1. Choose to install a zip from SD CARD > Choose UPDATE-SuperSU-v1.41.zip > Install
2. CWM will remove chinese SU and you now have Chainfire SU.
Done.
Click to expand...
Click to collapse
I tried with no luck. Phone is already rooted with the same method you mentioned. I flash the recovery image using the app, and the phone reboots to the stock recovery mode.
I'm not running the phone on a stock firmware.. Could that be the problem?
Manar Aleryani said:
I tried with no luck. Phone is already rooted with the same method you mentioned. I flash the recovery image using the app, and the phone reboots to the stock recovery mode.
I'm not running the phone on a stock firmware.. Could that be the problem?
Click to expand...
Click to collapse
I have the SAME problem! SU ok but the phone reboots to the stock recovery.... My firmware is original... What I do now?
Sorry, but VROOT threads are being closed by the moderation team because they appear to be collecting information off of devices. So, until this method is verified to be working safely and without malware, I would advise everyone not to use this method. Please report them to the moderation team.
Thanks!
Hello,
To All Motorola XPRT Users,
Motorola XPRT Is An Old Phone From Motorola Still With Android 2.2 Froyo. Due To It Is An Old Phone It Does Not Have Any Good Developer Support Or Choice Of Customizing With Custom Roms.
So Here I'll Be Instructing You On How To Root , Install CWM - Clock Work Mode Recovery And Flash A Few Custom Rom.
Let's Get Started Then !
Click to expand...
Click to collapse
Official Disclaimer
1. I Am Not Responsible For Any Damage To Your Phone Please Proceed At Your Own Risk.
2. The Methods Given Here Are Tested And If You Follow The To The Word It Sure Won't Brick Your Phone.
3. Even If You Somehow Brick Your Phone Or Get Stuck On Anything Please Let Me Know.
Click to expand...
Click to collapse
Pre-Requites :
1. It Is Recommended To Fully Charge Your Phone Or At Least Keep 80% Charge Just To Be Safe.
2. Keep A Backup Of Everything . It Will Help You To Get Your Data If You Do Something Wrong.
3. Go To Your Phone's Settings > Applications > Check The Box With Unknown Sources Written .
Go To The Development Options > Check USB Debugging
Click to expand...
Click to collapse
Root Your Device :
Download These File(s)
1. Super One Click
Follow As Written :
1. Download and place the SuperOneClick archive onto your Desktop.
2. Unzip files from the archive to your Desktop.
3. Turn ON the USB debugging option on your device by going to Menu>>Settings>>Applications>>Development>>USB debugging.
4. Once enabled, connect your device to your PC using the USB cable.
5. Double-click on the SuperOneClick executable file and it’ll launch.
6. Click on Root button in the app and it’ll start rooting your device.
7. Once your device’s rooted, reboot it.
8. And you’re all done!
Excellent! Your device has been successfully rooted and is equipped with the Superuser app for managing root permissions.
Click to expand...
Click to collapse
Install Clock Work Mode Recovery [CWMR]
Download These File(s):
1.Droid 2 Recovery Bootstrap
Follow As Written :
1. Download and install the Droid 2 Bootstrap app on your device using the link given above.
2. Once installed, launch it from your App Drawer.
3. Tap on Bootstrap Recovery button in the app.
4. Follow the on-screen instructions.
5. And you’re done!
Great! The recovery’s been successfully installed on your XPRT and you should be able to boot into the same by choosing Reboot Recovery option in the app!
Click to expand...
Click to collapse
Flash Custom Roms,
[Note : Please Make A Backup Using The CWMR To Revert back If Something May Go Wrong]
Rom Links For Your Phone :
1. Cyanogenmod 7 (Unofficial) for the Motorola XPRT
2. CyanogenMod 9 for Motorola XPRT
I'll Update If I Get Something More
Instructions To Install
1. After you download the .zip to your computer, plug in your device via USB cable.[Choose Any Rom For Your Device]
2. Copy the .zip file to the SD Card (do NOT extract it, just copy the whole zip file).
3. Unplug your device.
4. Now, open Droid 2 Bootstrap app .
5. Select Reboot into Recovery and wait for the device to reboot.
6. Once in recovery mode, use the volume buttons to navigate and power button to select Backup and Recovery.
7. Then select Backup and hit yes to confirm. Wait for it to finish backing up your current system (this will save you if something goes wrong).
8. Select Wipe Data / Factory Reset.
9. Select Flash zip from sdcard.
10. Select Choose zip from sdcard.
11. Find the ROM we copied to the sdcard in .zip format and select it. Then select yes to confirm. Wait for it to finish flashing.
12. Select Reboot System Now. Once it reboots (which will take a while the first time), you’ll be running the new ROM
Click to expand...
Click to collapse
So,
Enjoy.
Credits
1. Short fuse
2. Rom Authors
Click to expand...
Click to collapse
Written By
Pranto Roy
XDA
Click to expand...
Click to collapse
Post Your Experience.
Reserved
Reserved For Future
***
All thanks go to our awesome XDA-Developers, the developers at Oppo, and also to scumpicule for this working root method.
It doesn't require any alterations to the recovery system, just stick with the one that Oppo has provided.
This has only been tested on the X9076, it should theoretically work for other versions of the Find 7 as well, but please do this under your own discretion.
**Update: It has been reported that the newest Rom release of 1.2.2i or 1.2.3i and onward might not work with this root method! If this is the case, you will need to use these instructions from this post: http://forum.xda-developers.com/showpost.php?p=53902937&postcount=10
________________________________________________________________________________
CONTINUE with these instructions if you have Rom Version: 1.2.1i, otherwise if you have updated, click on the above link ^
INSTRUCTIONS:
Download the "Find7_ROOT4.3_bbs.oppo.cn.zip" file.
** It is also available at:
http://forum.xda-developers.com/showthread.php?t=2739102&highlight=find+7 **
Then Copy/Paste it in your phone on your root folder
Turn Off your phone
Simultaneously press the buttons ' power ' and 'volume down ' until you feel a vibration.
Your phone will reboot into recovery mode. ( Should be the OPPO recovery ! )
Select ' Choose English ' & Install zip file
Then choose the zip file that you have downloaded in step 1 & click "YES" to install.
Hit "Reboot" once everything is completed.
Go into app drawer and select the SuperSU app. Update the binary by selecting the "NORMAL" method.
Reopen SuperSU and make sure binary is okay.
Try downloading "Root Checker" or a app that requires root.
Congratulations, your device is now Rooted!!
________________________________________________________________________________
If you run into any errors, try updating the SuperSU binary again, or check under "NOTES" on the link above that scumpicule has posted.
________________________________________________________________________________
HIT THE THANKS BUTTON IF THIS HAS HELPED YOU.
Credits & Thanks
@karben @kedro @tk @Jimmy McGee
@scumpicule
installation failed unfortunately
i followed your steps and my device number is X9076
crackjas said:
installation failed unfortunately
i followed your steps and my device number is X9076
Click to expand...
Click to collapse
I'm pretty sure I used the same .zip file earlier today with the stock recovery, installation failed here too. (X9076).
Fortunately this worked perfectly: Click Here
binaryfalcon said:
I'm pretty sure I used the same .zip file earlier today with the stock recovery, installation failed here too. (X9076).
Fortunately this worked perfectly: Click Here
Click to expand...
Click to collapse
Thanks. It works!:good:
crackjas said:
installation failed unfortunately
i followed your steps and my device number is X9076
Click to expand...
Click to collapse
Were you able to get to SuperSU in the app drawer? Make sure that the binary was installed properly.
It's interesting because I was able to get it to work perfectly.
See attached photos of Root Checker.
Does not work on ColorOS 1.2.2i
I just got my Find 7 phone and after the OTA upgraded the system to 1.2.2i, when I tried to install the root file and it failed to install.
Installation Failed
No luck. Failed at the zip file installation part. Please let me know if you have any solution. Thanks. Cheers.:cyclops:
KoTP said:
No luck. Failed at the zip file installation part. Please let me know if you have any solution. Thanks. Cheers.:cyclops:
Click to expand...
Click to collapse
I'm having the same problem. When installing the zip from Oppo Recovery, it fails immediately every time. Tried both the Find7_ROOT4.3 and the Find7_GSM4.3 files. Any suggestions?
I think that after the update to 1.2.2i, the root might not work anymore. For all those that don't have it working, can you confirm if you have the 1.2.2i Rom version?
Sent from my X9076 using XDA Free mobile app
Good news!
I have found the Rooting method and instructions for Rom version 1.2.2i
It should work for every Oppo Find 7 and 7a (not confirmed) with any system (till 1.2.2i at least).
In the end system, bootloader and recovery will be intact - > stock rooted.
WORKING ON: x9077, x9076, x9006 (confirmed by #Oiler)
(NOTE):
Android SDK is required (which gives ADB and FASTBOOT files), if you have these files already on your computer, then you can just download TWRP, STOCK RECOVERY (oppo), and SUPERSU.
All the files are located below:
Preparation:
1. Phone with at least 30% battery.
2. Install Oppo drivers from "OPPO Driver" phone partition.
3. Download and unzip: AndroidSDKSlim - https://mega.co.nz/#!SEhFXbzL!Xy4PrX_NKFnAZvPaggQL-1Vw1PESzRCyqXiPrMlvWVM
4. Download: TWRP - https://mega.co.nz/#!gF0GhBzT!HGaWCcQfqr_ns2z7ZEIeeF-0KvXFliEOAFZ_Z-wHcdw and put it in "platform-tools" folder wich u get from zip above. (img file)
5. Download: Stock Recovery - https://mega.co.nz/#!rVQWXKhD!Ljy9pw_sy0VlKzxqJwuD4UoZGMwF_dOmOYWgR1mMRc4 Mod or Stock Recoveryhttp://ge.tt/2EQ5h2m1/v/0?c *2 and put it in "platform-tools" folder. (img file)
6. Download: SuperSU - http://download.chainfire.eu/451/SuperSU/UPDATE-SuperSU-v2.01.zip?retrieve_file=1 and put it on phone internal storage. (do not unpack)
Changing Recovery Menu:
1. Turn Off phone.
2. Press Volume UP + Power
3. Now u should see small discription on screen: fastboot
5. Plug the phone to PC.
4. Open command prompt inside "platform-tools" folder -> press SHIFT + Right Mouse Click, pick open command prompt here.
5. Write:
Code:
fastboot devices
6. You should see:
Code:
"your phone product code" Dartmoor
7. If you don't see your device listed, make sure drivers are installed properly. Next, write:
Code:
fastboot flash recovery twrp-x9077.img
after few second you should see OKAY. (No need to turn off phone) *1
Rooting the phone:
1. Power off the phone.
2. Hold volume DOWN and the POWER button to get into the TWRP Recovery.
3. Pick install and find the SuperSU zip file, confirm the flash.
4. Reboot the phone. (cash and davlik wipe not nessesary)
5. Phone is now rooted. (Check if there is working SuperSU app. Update binary if needed.)
Restoring stock Recovery Menu:
1. Power off the phone.
2. Press Volume UP + Power
3. Open command prompt on your PC inside "platform-tools" folder -> press SHIFT + Right Mouse Click, pick open command prompt here.
4. Write:
Code:
fastboot flash recovery x9077-official-recovery-mod.img
after few second you should see OKAY.
5. REBOOT, or turn off phone by pressing POWER for 3 sec.
6. Check Recovery Menu (Volume DOWN + Power)
____________________________________________________________________
NOTES:
*1 turning off after installing Recovery Mod is unnecessary, this is because the phone won't startup automatically into the installed Recovery Mod.
*2 Stock Recovery is provided as genuine by #Zeus (Oppo Official Staff). The other one - Stock Recovery Mod is provided by #Kedros which have removed checking of Oppo system (provides possibility to install custom files like roms or SuperSU etc.). #Kedros confirmed that OTA update is still available on it.
____________________________________________________________________
Give a Like if it helped
SOURCE: Jach0o from OPPO forums
JiraffeLeung said:
I think that after the update to 1.2.2i, the root might not work anymore. For all those that don't have it working, can you confirm if you have the 1.2.2i Rom version?
Sent from my X9076 using XDA Free mobile app
Click to expand...
Click to collapse
Yes. Mine is 1.2.2i
Same for me on the version number. 1.2.2I I was hoping the process would be easier. Oh well.
The link to the TWRP recovery is down. I tried to download it in every possible way, but I always get an error. WHen I click download once I get to MEGA, it is saying "temporary error, retrying". Please fix, thanks.
Edit - NM working now, thanks just in case you fixed it.
Edit - Rooted phone, left TWRP on if I ever go to CM11s. Had to do a few things diffrent than what you said, but got it to work. Thanks
JiraffeLeung said:
Good news!
I have found the Rooting method and instructions for Rom version 1.2.2i
It should work for every Oppo Find 7 and 7a (not confirmed) with any system (till 1.2.2i at least).
In the end system, bootloader and recovery will be intact - > stock rooted.
WORKING ON: x9077, x9076, x9006 (confirmed by #Oiler)
(NOTE):
Android SDK is required (which gives ADB and FASTBOOT files), if you have these files already on your computer, then you can just download TWRP, STOCK RECOVERY (oppo), and SUPERSU.
All the files are located below:
Preparation:
1. Phone with at least 30% battery.
2. Install Oppo drivers from "OPPO Driver" phone partition.
3. Download and unzip: AndroidSDKSlim - https://mega.co.nz/#!SEhFXbzL!Xy4PrX_NKFnAZvPaggQL-1Vw1PESzRCyqXiPrMlvWVM
4. Download: TWRP - https://mega.co.nz/#!gF0GhBzT!HGaWCcQfqr_ns2z7ZEIeeF-0KvXFliEOAFZ_Z-wHcdw and put it in "platform-tools" folder wich u get from zip above. (img file)
5. Download: Stock Recovery - https://mega.co.nz/#!rVQWXKhD!Ljy9pw_sy0VlKzxqJwuD4UoZGMwF_dOmOYWgR1mMRc4 Mod or Stock Recoveryhttp://ge.tt/2EQ5h2m1/v/0?c *2 and put it in "platform-tools" folder. (img file)
6. Download: SuperSU - http://download.chainfire.eu/451/SuperSU/UPDATE-SuperSU-v2.01.zip?retrieve_file=1 and put it on phone internal storage. (do not unpack)
Click to expand...
Click to collapse
Great stuff.
Feel free to share how you got it Rooted and which steps you took. It will help others here as well.
Sent from my X9076 using XDA Free mobile app
JiraffeLeung said:
Great stuff.
Feel free to share how you got it Rooted and which steps you took. It will help others here as well.
Sent from my X9076 using XDA Free mobile app
Click to expand...
Click to collapse
Total newbie. Could you explain preparation step 2 to me? (2. Install Oppo drivers from "OPPO Driver" phone partition.)
Will this method work with version 1.2.3i?
Many thanks.
Hey, yes the method should work for the most recent version as well. When you plug in your phone to you pc, it prompts you install the drivers from OPPO, just continue and install them.
If you don't see "Developer Options" in your settings ( in "More" ) then go into "About Phone" and click on "Build number" 5 times until you receive a message indicating that developer options is enabled.
Then plug in your phone and see if the drivers get updated. This process has been tested to work on Windows 7.
Sent from my X9076
I'm eager to try
JiraffeLeung said:
Hey, yes the method should work for the most recent version as well. When you plug in your phone to you pc, it prompts you install the drivers from OPPO, just continue and install them.
If you don't see "Developer Options" in your settings ( in "More" ) then go into "About Phone" and click on "Build number" 5 times until you receive a message indicating that developer options is enabled.
Then plug in your phone and see if the drivers get updated. This process has been tested to work on Windows 7.
Sent from my X9076
Click to expand...
Click to collapse
Thanks. Just waiting to find the time to try. I'll post the result.
Thanks again.
One more thing, you'll have to enable "USB Debugging" in developer options, then try plugging the phone in again.
Failed
JiraffeLeung said:
One more thing, you'll have to enable "USB Debugging" in developer options, then try plugging the phone in again.
Click to expand...
Click to collapse
Hi,
Thanks a lot for your help.
Though I'm pretty sure I've followed your instructions to the letter the phone would fail to install the update.SuperUser file so I can't get to get it rooted.
Any idea, suggestion, tip etc, will be much appreciated.
Thanks
How far were you able to get to? Any errors or freezing? What version of Rom are you on?
Please quick answer !!!
http://forum.xda-developers.com/galaxy-note-10-2014/general/root-root-stock-kernel-t3240218
And could someone explain to me step by step how to upload the root and recovery ? Because I too unknown to android .
kacper12897 said:
And could someone explain to me step by step how to upload the root and recovery ? Because I too unknown to android .
Click to expand...
Click to collapse
You can find how to root here. FULL CREDITS GO TO Zionator as he wrote up the instructions.
Easy Guide to Root :
1. Go to Rooting Guide - http://forum.xda-developers.com/gala...6#post63637426
Download only the P605 modded boot IMG and then come back here. Move the tar to tablet. "In my opinion that guide is very confusing" This is much more simple...
2. Go to TWRP (download version 2.8.7.0) - https://dl.twrp.me/lt03wifiue/
Download the img.tar This file you keep on pc to flash via Odin.
3. Go to SuperSU v2.52 Beta - https://download.chainfire.eu/743/Su...erSU-v2.52.zip
Download the zip. Move the zip to tablet.
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
5. When finished booting into TWRP pull Spen and click Install then find modded boot img "remember to switch between IMG & ZIP mode in the lower left hand corner" Now flash the boot img. Do not reboot just go back and switch back to ZIP mode and flash SuperSU when done reboot.
6. Wait for the boot to finish. You are now rooted.
I hope this makes it easy for you!!!
thank you for the guide buhohitr.
worked perfectly for me
buhohitr said:
You can find how to root here. FULL CREDITS GO TO Zionator as he wrote up the instructions.
Easy Guide to Root :
1. Go to Rooting Guide - http://forum.xda-developers.com/gala...6#post63637426
Download only the P605 modded boot IMG and then come back here. Move the tar to tablet. "In my opinion that guide is very confusing" This is much more simple...
2. Go to TWRP (download version 2.8.7.0) - https://dl.twrp.me/lt03wifiue/
Download the img.tar This file you keep on pc to flash via Odin.
3. Go to SuperSU v2.52 Beta - https://download.chainfire.eu/743/Su...erSU-v2.52.zip
Download the zip. Move the zip to tablet.
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
5. When finished booting into TWRP pull Spen and click Install then find modded boot img "remember to switch between IMG & ZIP mode in the lower left hand corner" Now flash the boot img. Do not reboot just go back and switch back to ZIP mode and flash SuperSU when done reboot.
6. Wait for the boot to finish. You are now rooted.
I hope this makes it easy for you!!!
Click to expand...
Click to collapse
404 Page Not Found
Oh snap! Something broke! A genius monkey has been alerted.
Until he fixes it, use our glorious search tool to find ROMs, apps, tools, and other sweet mods for your phone.
haha.... http://forum.xda-developers.com/gala...ernel-t3240218