Related
i just flash this http://www.multiupload.com/OABIOPUGX7 ftf file then fastboot DooMKernel-v8
and install bravia engine.
Bravia engine work perfectly for now, but the wireless cant use,
i tried install wifi module, provide by doomlord, and its still same,
there is some method that i dont understand,
7. reboot phone and enter recovery mode
8. flash the wifi modules update.zip for my kernel (is it suppose to mean this ' Select Install ZIP from SD Card and then Choose ZIP from SD Card, then from the browser select the ZIP folder you copied earlier and enter. )
9. reboot phone
If what i mean is true...does it mean that what i've doing right now is totally right.
so guys any solution ?
p/s : english not my primary lang.
Hello Everybody!!
Recently when going through the xda forums for the devices Karbonn Titanium S1, Cherry Mobile Flame 2.0, K-Touch Hornet u86 kiss , I noticed that a lot of people have questions regarding Stock rom, Recovery rooting and Solutions for Brick.However most of the posts have been left unanswered or died for some reason.
Hence I decided to open a thread that can be used to solve general problems and issues regarding the Device.
NOTE:- Archos 45 Platinum too has similar device specifications.The same CWM version worked for @best98 who is using an Archos 45 Platinum.
Tip:Using CWM touch recovery
When using the CWM Touch recovery you may notice that it is not really working properly and that touch is not doing anything. The fact is the touch is being registered and that the touch method is different than normal android because of limited drivers in recovery.
The working
Use one finger touch to scroll
Use two finger touch to select item
Installing a Recovery Menu
Using PC
1) Install the Mobile Drivers.
2) Download Minimal ADB And fastboot [Windows users] Linux and Mac users might have to download the whole Android sdk as of now.
3) Download the recovery you want from the attachments below.
4) Rename them to recovery.img after extracting and copy it to a folder of know location.
5) Boot your device into fastboot mode.i.e Power on your mobile by pressing and holding Power button and vol+ Key.until you see A green screen.
6) Connect your device to the PC and open Minimal ADB and fastboot
7) Run the command " fastboot flash recovery C:\USERS\MYNAME\DESKTOP\ANDROID\RECOVERY.IMG".
Without the quotes replace C:\USERS\MYNAME\DESKTOP\ANDROID\ with the location where you extracted recovery.img.
8) Wait untill it completes and VOILA new recovery installed.
Note: In case you want to preserve your stock recovery, run the command "fastboot boot C:\USERS\MYNAME\DESKTOP\ANDROID\RECOVERY.IMG"
Without the quotes replace C:\USERS\MYNAME\DESKTOP\ANDROID\ with the location where you extracted recovery.img.
Using Mobile
Simple Method.
Just install the TACK Manager from here and install the recovery .Enjoy .
Not so simple method
Download the flashable recoveries from Below and flash it through CWM Or TWRP [Yes, you need custom recovery for this to flash]
Click to expand...
Click to collapse
Rooting Your Device
Method 1: Through CWM/TWRP
1) Download the SuperSU package provided below.
2) Copy it to the root of your SDCard
3) Select Install zip from SDCard
Method 2:Through Framaroot
Personally I Did not get any success by this method.But lot of users reported it to to work by using the Gandalf exploit.
Also some versions of framaroot work better on some devices as compared to others.So maybe just have to check which version works for our Mobile.
1) Download and install Framaroot.apk
2) On the exploits list select Gandalf
3) It'll probably crash the first time and apparently work the second time you launch it.
As I Am not sure which version of framaroot works for this mobile hence no upload
Click to expand...
Click to collapse
Reserved
Flashing Roms and Fix Soft brick
1) Copy Rom to SDCard
2) Boot into Recovery by Powering on while holding power and vol+ Button.Initially you'll see a green screen...Keep holding untill the screen turns red.
3) Goto Mounts and storage and format /Cache and /Data. Format /SYSTEM if installing new rom.
4) Goto Advanced and format Dalvik Cache
5) Select Apply Zip from SD Card
6) Select zip file of rom to install and wait.
7) Reboot and voila.
Note:This is assuming you are using CWMR
Note: Do not format /SYS_BOOT Partition.You'll end up bricking your device and then will not be able to boot into Fastboot mode.
If this happens by mistake.Follow the next Guide.
Click to expand...
Click to collapse
Fixing RESET FOR ENTRY QPST DOWNLOAD
In case you end up Formatting /SYS_BOOT Partition then you'll most likely end up in this.There might be few other cases when this can happen but none that i am aware of.
If you Have a Linux Desktop
If you have access to Linux PC then connect your mobile to it and mount the partition which is around 50 MB. Download the Images.zip from below.unzip the file and copy the whole folder to the 50 MB partition.
Your File structure should look something like this
-\50MBPartition
-\image
-\AMSS.MBN
-\AMSSHD.MBN
If you have Windows
http://www.filefactory.com/file/2n5ygdzybijv
I'll soon put up a guide for windows users.
This is the guide I found on facebook's CM Flame 2.0 group.
DISCLAIMER:
This fix worked for me. I WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE TO YOUR PHONE, YOU DO THIS AT YOUR OWN RISK!!! Please do the process step-by-step. DON'T SKIP any step as I don't know what will happen and there's a possibilty that your phone will be dead permanently.
TOOLS NEEDED:
Roadkill and StockROM
DOWNLOAD STEPS:
1. Go to www.dropbox.com
2. SIGN-IN using MY credentials
E-mail: [email protected]
Password: dropbox-pemaustria
3. Navigate to the folder cmflame2, there you can find the file.
4. Right click cmflame2stock.zipx, and click download.
(THIS STEPS LEAVE ME NO CHOICE BUT TO GIVE MY DROPBOX ACCOUNT TO YOU. AS A RESPECT, PLEASE DO NOT CHANGE ANY ACCOUNTS AND SECURITY SETTINGS ON MY PROFILE. THANK YOU)
NOTE: Please use WinZip for extracting files. Thanks
TUTORIALS:
1. Disconnect all USB drives especially flash drives, including memory cards.
2. Turn on your device to QPST Mode, and connect it to computer. When a window prompt you to format card. CANCEL.
3. Extract the contents of cmflame2stock.zipx and run Roadkill.exe. Click 'Yes' if administrative privilages prompt you.
4. In the left side of 'Write image to' choose PHYSICAL DISK 1(3.61GB). In my case it is 3.61 GB. Your size must be approximately 4GB. CHOOSE THE RIGHT DISK. CHOOSING THE WRONG DISK WILL RESULT DAMAGE to the selected disk.
5. In your extracted folder, you will see an image file named CM-Flame2.0-StockROM.img.
6. On source file, browse for the image file you just extracted.
7. Click 'START', wait for the process until it's finished.
Click to expand...
Click to collapse
Custom ROM's
Stock Rom
Karbonn Titanium S1
Flashable ZIP
CWM Backup
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Cherry Mobile Flame 2.0
Flashable ZIP
K-Touch Hornet U86 Kiss
K-Touch 1.3.4 Rom
Archos 45 Platinum
Archos 45 CWM Backup
Click to expand...
Click to collapse
Custom ROMS
LeWa OS 14.05.16
Download
One of the most stable ROMs I've seen for our device.It is Continiuosly developed and supported at Lewatek and has weekly updates at friday.OTA update are available so you don't have to download the whole ROM
MIUI ROM 4.1.17
Highly Customizable ROM.
MIUI Is known for the amount of customization you can do with it.From Statusbar to Lockscreen to everything normal android OS can do.
MIUI ROM Download
Lenovo Magic 4.0
With Support for over 11 Languages and
Download
CM10.1
CM10.1 Base ROM
Update File
CM10.2 Alpha
CM10.2 ROM
CM11 Alpha 3
CM11 ROM
Nokia X ROM Port
This ROM is ported by our friend rdis.
You can find the ROM here
AOSP KitkatFlare
More like Stock ROM with KitKat touch in it.Cooler and more Powerful
This is a KitKat Look alike and not the actual kitkat. For KitKat Check CM11 Above.
AOSP KitKatFlare
IXYNOS
Based on stock
Fully themed with color combination of cyan, yellow, purple and white
Slim rom around 189 Mb
init.d tweaks
build.prop tweaks
ttpod
mifileexplorer
pre rooted
zipaligned
net speed in status bar
good battery life
extremely smooth high performance rom
camera with smile detection
Ixynos ROM
Xperia Z
Xperia Z Download
Click to expand...
Click to collapse
Reserved
Reserved
Thanks idrogon81
idragon81 said:
Hello Everybody!!
Recently when going through the xda forums for the devices Karbonn Titanium S1, Cherry Mobile Flame 2.0, K-Touch Hornet u86 kiss [Hence reffered to as TCK-SU186, Simply because it is easier to refer to ], I noticed that a lot of people have questions regarding Stock rom, Recovery rooting and Solutions for Brick.However most of the posts have been left unanswered or died for some reason.
Hence I decided to open a thread that can be used to solve general problems and issues regarding the Device.
Stock Rom
Custom Recovery
Rooting Method
Click to expand...
Click to collapse
Framarook-1.7.0.apk works fine to root karbonn s1 titanium without any crash. use gandalf exploit and its done.
sunilneelam said:
Framarook-1.7.0.apk works fine to root karbonn s1 titanium without any crash. use gandalf exploit and its done.
Click to expand...
Click to collapse
That's strange :/
Didnt work for me
Any Cynogenmod roms
idragon81 said:
Hello Everybody!!
Recently when going through the xda forums for the devices Karbonn Titanium S1, Cherry Mobile Flame 2.0, K-Touch Hornet u86 kiss [Hence reffered to as TCK-SU186, Simply because it is easier to refer to ], I noticed that a lot of people have questions regarding Stock rom, Recovery rooting and Solutions for Brick.However most of the posts have been left unanswered or died for some reason.
Hence I decided to open a thread that can be used to solve general problems and issues regarding the Device.
Stock Rom
Custom Recovery
Rooting Method
Click to expand...
Click to collapse
I loved Cynogenmod and I also want it to be on my device
Any help will be appreciated
LOLya said:
I loved Cynogenmod and I also want it to be on my device
Any help will be appreciated
Click to expand...
Click to collapse
There is CM10.1 for Our device. However i didnt find it to be stable.Didn't find ways to connect to data and some people had issues with microphone not working.
I'll be uploading more unbrick solutuions first, followed by MIUI rom and then CM10.1
TY
idragon81 said:
There is CM10.1 for Our device. However i didnt find it to be stable.Didn't find ways to connect to data and some people had issues with microphone not working.
I'll be uploading more unbrick solutuions first, followed by MIUI rom and then CM10.1
Click to expand...
Click to collapse
If uget it bugfree plz upload it
Thanks
English TWRP
idragon81 said:
Hello Everybody!!
Recently when going through the xda forums for the devices Karbonn Titanium S1, Cherry Mobile Flame 2.0, K-Touch Hornet u86 kiss [Hence reffered to as TCK-SU186, Simply because it is easier to refer to ], I noticed that a lot of people have questions regarding Stock rom, Recovery rooting and Solutions for Brick.However most of the posts have been left unanswered or died for some reason.
Hence I decided to open a thread that can be used to solve general problems and issues regarding the Device.
Stock Rom
Custom Recovery
Rooting Method
Click to expand...
Click to collapse
The TWRP is in Japanese Language can u upload english twrp.img
I googled for it but did'nt get it
Hi,
Great to read that.. at least after crawling the web and finding that Karbon S5 is equivalent to Archos 50 Platinum.. I find from the specs that this Karbonn S1 is the same as the Archos 45 Platinum that I own.
Specs are : here for the Archos 45..
http://www.archos.com/gb/products/smartphones/platinum/archos_45platinum/specs.html?#a
Finally.. I can't wait to see Cyanogen on it.. maybe a chance to have a CM11 ?
Regards
at last i could successfully port android 4.2.2 to karbonn titanium s1...
the rom is being uploaded...its named as "CHEEKUMOD" as it is edited by me
whats working:
ALMOST EVERYTHING :fingers-crossed:
whats NOT working:
CAMERA FOCUS
REST ALL ITS JUST FINE AND AWESOME !!
see the screen shots mean while
Karbonn Titanium S1 custom rom
VOILA !!
At last the first custom rom for Karbonn Titanium S1 is here !!
the most waited Android 4.2.2 for Karbonn Titanium S1
Custom DPI for better looks...
========================================================================================================
Whats WORKING:
VERSION 1
ALMOST EVERYTHING
VERSION 2
ALMOST EVERYTHING
========================================================================================================
Whats NOT WORKING:
VERSION 1
CAMERA FOCUS
SOMETIMES MICROPHONE IN CALL WONT WORK !!
VERSION 2
CAMERA FOCUS
Will give the fix soon,or someone please help me out to fix it...
========================================================================================================
HOW TO INSTALL THE ROM:
Download the rom and gapps and place it in the root of the SD card (Root meaning directly in ur SD card and not in folders so u can find it easily in the recovery)
VERSION 1:
ROM DOWNLOAD: drive.google.com/file/d/0Bz2-ARVuWcM9ZjNvNkJTLWZidnM/edit?usp=sharing
Gapps DOWNLOAD: drive.google.com/file/d/0Bz2-ARVuWcM9LW5TV2xMS2cydnc/edit?usp=sharing
INSTALL CLOCKWORKMOD
How to install clockwork mod for newbies (IF U HAVE CWM ALREADY INSTALLED U CAN SKIP THIS)
Things required:-
Recovery.img (Find in attachments below)
AIO flasher (Find in attachments below)
And of-course ur phone and USB cable
1.Switch off your phone.
2.Boot into fastboot (to boot into fastboot hold volume up+power button for few seconds untill u see a whole green screen and release both the buttons)
3.plug in your phone to pc via USB cable.
4.Download the AIO flasher from attachment below,extract it and open it (Run as admin in pc if required).
5.Select recovery in the AIO flasher and click on select file and select the recovery.img which u downloaded from the attachments below.
6.Now check the erase option and click on flash and wait till it reads "finished" in the AIO flasher dialog box.
7.Remove the cable and pull the battery and re insert it to exit fastboot.
Congratulations !! You have successfully installed CWM on ur device.
BOOT INTO RECOVERY MODE
To boot into recovery mode u need to hold the volume up+power buttons untill the screen turns green and do not release the buttons now hold untill the screen turns red and release the buttons.Wait for sometime untill it boots into the recovery.
navigate using the volume keys and select using the power keys.
1.Select Wipe data/factory reset.
2.Navigate to Advanced and select it.
3.Wipe dalvik cache and go back to main.
4.Now select install zip from sd card.
5.Now select choose zip from sdcard.
6.Select the rom which u downloaded and copied to the root of the SD card.
7.And select yes.
8.Wait until it reads installation complete.
9.And using the same method from step.4 also install the gapps. to flash Gapps u need to select the gapps file instead of rom file.
NOW reboot and enjoy !! IF IT DOSENT REBOOT DONT PANIC PULL THE BATTERY AND POWER ON MANUALLY
Congratulations !!
Your device is running Android 4.2.2 now.
And if u liked this please +1 this
========================================================================================================
DOWNLOAD THE VERSION 2 OF MY ROM HERE WITH MIC FIX AND GAPPS !!
IMPORTANT !!!!!!!!!!!!!!!!!!!!!!! <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
DO NOT FLASH GAPPS WITH THIS VERSION OF MY ROM IT IS PRE INSTALLED IN THE ROM...!!
VERSION 2:
ROM DOWNLOAD: https://drive.google.com/file/d/0Bz2-ARVuWcM9SUVkUnJSSnV3WEU/edit?usp=sharing
GAPPS DOWNLOAD: ITS PRE INSTALLED IN THE ROM DO NOT FLASH AGAIN !! < < < < < < < < < < < < < < < < <---------------------NOTE
Changelog:
1:Fixed "Mic not working in call".
2:have added gapps in the rom file to minimize flashing procedure of flashing each at a time.
========================================================================================================
DISCLAIMER:
NOTHING WILL GO WRONG NORMALLY BECAUSE I HAVE TESTED THESE PERSONALLY BUT IF IT HAPPENS TO U I AM NOT RESPONSIBLE..!!
HAVE A BACKUP OF UR DEVICE so if something goes wrong u can revert the phone to the earlier working stage.
I AM NOT RESPONSIBLE FOR BRICKING OF YOUR PHONES DUE TO THIS PROCEDURE DO IT AT YOUR OWN RISK !!
pls..
idragon81 said:
Flashing Roms and Fix Soft brick
Fixing RESET FOR ENTRY QPST DOWNLOAD
Click to expand...
Click to collapse
Pls.. post a guide for windows users.thanks
CWM is the solution
claymisteryo said:
Pls.. post a guide for windows users.thanks
Click to expand...
Click to collapse
Its not necessary to flash or reset the soft brick using any OS,
U can do it by CWM also.
1]For softbrick u can just factory reset and wipe cache
2] for flashing u can mount and remount sdcard and copy the .zip file to it and choose install zip from sdcard
Plz accept my request
ROM DOWNLOAD: drive.google.com/file/d/0Bz2-ARVuWcM9ZjNvNkJTLWZidnM/edit?usp=sharing
Click to expand...
Click to collapse
Hey Cheetan I just requested u for rom from the link plz accept it I want to try it
LOLya said:
Hey Cheetan I just requested u for rom from the link plz accept it I want to try it
Click to expand...
Click to collapse
me too not able to download
Mincrophone not working!!
when you call, the other person cannot hear your voice.... plz fix this!
its quite a major BUG!
Original Site
chetan007cheeku said:
VOILA !!
At last the first custom rom for Karbonn Titanium S1 is here !!
the most waited Android 4.2.2 for Karbonn Titanium S1
Custom DPI for better looks...
Whats WORKING:
ALMOST EVERYTHING
Whats NOT WORKING:
CAMERA FOCUS
SOMETIMES MICROPHONE IN CALL WONT WORK !!
Will give the fix soon,or someone please help me out to fix it...
HOW TO INSTALL THE ROM:
Download the rom and gapps and place it in the root of the SD card (Root meaning directly in ur SD card and not in folders so u can find it easily in the recovery)
ROM DOWNLOAD: drive.google.com/file/d/0Bz2-ARVuWcM9ZjNvNkJTLWZidnM/edit?usp=sharing
Gapps DOWNLOAD: drive.google.com/file/d/0Bz2-ARVuWcM9LW5TV2xMS2cydnc/edit?usp=sharing
INSTALL CLOCKWORKMOD
How to install clockwork mod for newbies (IF U HAVE CWM ALREADY INSTALLED U CAN SKIP THIS)
Things required:-
Recovery.img (Find in attachments below)
AIO flasher (Find in attachments below)
And of-course ur phone and USB cable
1.Switch off your phone.
2.Boot into fastboot (to boot into fastboot hold volume up+power button for few seconds untill u see a whole green screen and release both the buttons)
3.plug in your phone to pc via USB cable.
4.Download the AIO flasher from attachment below,extract it and open it (Run as admin in pc if required).
5.Select recovery in the AIO flasher and click on select file and select the recovery.img which u downloaded from the attachments below.
6.Now check the erase option and click on flash and wait till it reads "finished" in the AIO flasher dialog box.
7.Remove the cable and pull the battery and re insert it to exit fastboot.
Congratulations !! You have successfully installed CWM on ur device.
BOOT INTO RECOVERY MODE
To boot into recovery mode u need to hold the volume up+power buttons untill the screen turns green and do not release the buttons now hold untill the screen turns red and release the buttons.Wait for sometime untill it boots into the recovery.
navigate using the volume keys and select using the power keys.
1.Select Wipe data/factory reset.
2.Navigate to Advanced and select it.
3.Wipe dalvik cache and go back to main.
4.Now select install zip from sd card.
5.Now select choose zip from sdcard.
6.Select the rom which u downloaded and copied to the root of the SD card.
7.And select yes.
8.Wait until it reads installation complete.
9.And using the same method from step.4 also install the gapps. to flash Gapps u need to select the gapps file instead of rom file.
NOW reboot and enjoy !! IF IT DOSENT REBOOT DONT PANIC PULL THE BATTERY AND POWER ON MANUALLY
Congratulations !!
Your device is running Android 4.2.2 now.
And if u liked this please +1 this
DISCLAIMER:
NOTHING WILL GO WRONG NORMALLY BECAUSE I HAVE TESTED THESE PERSONALLY BUT IF IT HAPPENS TO U I AM NOT RESPONSIBLE..!!
HAVE A BACKUP OF UR DEVICE so if something goes wrong u can revert the phone to the earlier working stage.
I AM NOT RESPONSIBLE FOR BRICKING OF YOUR PHONES DUE TO THIS PROCEDURE DO IT AT YOUR OWN RISK !!
Click to expand...
Click to collapse
Actually Cheetan this is the site with the same ROM,no offence.You might have modified much in this ROM(Your ROM(Cheeku ROM))
Site: http://www.needrom.com/mobile/k-touch-u86-7
Problem is u just need to make account
LOLya said:
The TWRP is in Japanese Language can u upload english twrp.img
I googled for it but did'nt get it
Click to expand...
Click to collapse
can i use any twrp version instead?
ROOT + CWM + ROM (cleaned stock ~ custom) for HCL Me Connect 2.0 Tab V2
WARNING , THESE PROCEDURES WILL MAKE YOUR DEVICE OUT OF WARRANTY AND MAY BRICK YOUR DEVICE. PROCEED AT YOUR OWN RISK.
Make sure USB Drivers are installed on your PC.
------------------------------------------------------------
X. Rooting Steps:
1. Turn on USB Debugging on Tab
2. Download Vroot on your PC ( Google it or www.mgyun.com/en/getvroot )
3. Run Vroot & Connect your Tab to PC. Vroot will auto detect the device and root it..
------------------------------------------------------------------
XX. Installing CWM
1. Download and install two apps like File Manager with root access and SManager ( Script Manager) for console.
2. Grant root access to both apps.
3. Download recovery and flash from link:
http://www.mediafire.com/download/vf5xy1hb7kb12ha/HCL_Tab_CWM.rar
4. Extact the file (flash_image and recovery.img) on your internal sd card and after extarction, copy both files to root folder named "/dev" using File Explorer(with root access).
5.Enter root shell by running SManager Console.
6. Type the following commands:
Command 1:
chmod 755 /dev/flash_image
Command 2:
/dev/flash_image recovery /dev/recovery.img
( type the command exactly, care for no uppercases, better copy and paste)
6. After entering the command, u will get " recovery successfully updated"
7. Now u have recovery installed, u may boot into recovery by shutting down ur tab and pressing power and volume dowm button together for around 7 secs until logo shows up.
Congrats now u have rooted tab and a custom recovery CWM.
--------------------------------------------------------------------
XXX. ROM ( will update later)
I have not prepared custom rom but instead i have cleaned rom of my tab with all bloatwares and nice UI and launcher ( Screenshot attached) .
You may download the file ( ~ 220 MB ) and restore with CWM recovry by following below steps:
DOWNLOAD LINKS (FILE UPLOADED IN PARTS, DOWNLOAD ALL 3 PARTS BEFORE UNZIPPING):
http://www.mediafire.com/download/8prnbeuybkptnca/clockworkmod.zip
http://www.mediafire.com/download/cq9t74v0pdk4l4k/clockworkmod.z01
http://www.mediafire.com/download/7ukn7psr2byb2cw/clockworkmod.z02
1. First make backup of current rom through CWM.
2. Backup rom on ur pc by switching on the device.
3. Extract the contents of downloaded files into internal sd.
4. Goto CWM Recovery, then format system, format data, format cache and wipe format dalvik cache.
5. Now choose restore option to restore the downloaded clean rom..
WARNING , THESE PROCEDURES WILL MAKE YOUR DEVICE OUT OF WARRANTY AND MAY BRICK YOUR DEVICE. DO IT AT YOUR OWN RISK.
Thanks man i 've successfully installed clock work mod recovery 6.I am waiting for the ROM
Sent from my Connect-2G-2.0 using xda app-developers app
BackupTA
You forgot to mention BackupTA application before doing all of this..
It helps u revert ur phone to the original stock state as if there was never any tweaking..
Great way for not making the warranty void..
Cheers..
---------- Post added at 01:57 AM ---------- Previous post was at 01:52 AM ----------
Oh!!
Here's the link..
http://forum.xda-developers.com/xpe.../tutorial-backup-ta-partition-to-drm-t2234627
rom
waiting for the rom man
connect 2g 2.0
Thank You So much for this wonderful tutorial ,Now i've got CWM working on my HCL me connect 2g 2.0,All the other tutorials on other sites were not working
good work bro but waiting for the rom
Bro i have rooted and installed CWM Recovery by using your tutorial but Unfortunately i have deleted my rom and i have downloaded the stouk rom from the hcl (official website) but it is also in .img , so i can't even flash it throw the CWM Recovery, and if i switch on my tablet, it stuck on boot logo,
So, please bro made the custom rom fast as possible :crying:
and bro good luck for your future
Thanks
rom link added
rom link added, you may recover your device...
gautam908 said:
Bro i have rooted and installed CWM Recovery by using your tutorial but Unfortunately i have deleted my rom and i have downloaded the stouk rom from the hcl (official website) but it is also in .img , so i can't even flash it throw the CWM Recovery, and if i switch on my tablet, it stuck on boot logo,
So, please bro made the custom rom fast as possible :crying:
and bro good luck for your future
Thanks
Click to expand...
Click to collapse
I need help while extracting the file :/
The one file is in .zip and another two files is in .z01 and .z02 file and cannot be extract, Bro help me please
If you can give the screen shot please it would help me a lot
Thanks
MD5 mismatch
Bro I have extracted the backup file of the ROM and while restoring it I was getting an error of MD5 mismatch???? Any solution???
Waiting for rom
I hav install cwm recovery.can you post the link of cyanogen mod custom rom
hello everyone, please help me to port cm 12 for my tablet: HCL me connect 2.0. above stock rom files are missing.. techincal speciation are: 1 GHz cortex A9 CPU , 1GB DDR3 RAM currently running on android 4.1 jelly bean os.
please guide and help me to update my tablet andriod version..
I saw this in facebook group "xperia t3 - india".. it seems we just need the camera to work
and 4G, and sdcard1...
vmlc said:
I saw this in facebook group "xperia t3 - india".. it seems we just need the camera to work
Click to expand...
Click to collapse
Hi i'm the guy how have cyanogen on my T3 , I just wanted to warn you for the rom, select the FXP-cm12-20150412...
And not the FXP-cm12.1 ...
otherwise your phone will bootloop, and when you make the first start of the phone , don't worry if after the bootanimation there's a black screen just wait 2-3 minutes for the update
So enjoy Cyanogen Xperia Users
fastbooking said:
Hi i'm the guy how have cyanogen on my T3 , I just wanted to warn you for the rom, select the FXP-cm12-20150412...
And not the FXP-cm12.1 ...
otherwise your phone will bootloop, and when you make the first start of the phone , don't worry if after the bootanimation there's a black screen just wait 2-3 minutes for the update
So enjoy Cyanogen Xperia Users
Click to expand...
Click to collapse
so, you confirm no 4g and camera working?
vmlc said:
so, you confirm no 4g and camera working?
Click to expand...
Click to collapse
yes no camera and 3G/4G
fastbooking said:
yes no camera and 3G/4G
Click to expand...
Click to collapse
also, you should do a detailed tutorial how to try the seagull build, i tried it the other day, but I couldnt do it....
vmlc said:
also, you should do a detailed tutorial how to try the seagull build, i tried it the other day, but I couldnt do it....
Click to expand...
Click to collapse
I will try tomorow there's a french tutorial about that here's the link for the one's who speak french
phonandroid.com/forum/post1800321.html (www . before its just because i can't now)
Cyanogen ROM are distributed in zip format, so you have to :
- push the zip file to your sdcard
- you need a kernel with recovery (for the time being, the Philz one)
- you enter in recovery mode
- you select "install zip" and the zip file.
once it's finished, install the right kernel
for that, on your PC, extract the boot.img file from the ROM zip file and flash it with flashtool or fastboot
reboot and enjoy
dan15 said:
Cyanogen ROM are distributed in zip format, so you have to :
- push the zip file to your sdcard
- you need a kernel with recovery (for the time being, the Philz one)
- you enter in recovery mode
- you select "install zip" and the zip file.
once it's finished, install the right kernel
for that, on your PC, extract the boot.img file from the ROM zip file and flash it with flashtool or fastboot
reboot and enjoy
Click to expand...
Click to collapse
ok, the part I dont get is: "once it's finished, install the right kernel
for that, on your PC, extract the boot.img file from the ROM zip file and flash it with flashtool or fastboot"
how do you do this?
dan15 said:
Cyanogen ROM are distributed in zip format, so you have to :
- push the zip file to your sdcard
- you need a kernel with recovery (for the time being, the Philz one)
- you enter in recovery mode
- you select "install zip" and the zip file.
once it's finished, install the right kernel
for that, on your PC, extract the boot.img file from the ROM zip file and flash it with flashtool or fastboot
reboot and enjoy
Click to expand...
Click to collapse
I don't install cyanogen like that,
First I update my phone with EMMA with the Open devices TA
-After I open the zip of the rom and i extract it somewhere you can find it
-take the zip AND THE GAPPS and connect your phone on usb for sending the zip on THE ROOT of your sdcard
-Enter in fastboot, and open flashtool (not emma the other)
-Flash the kernel called : boot.img
-Once Flashed reboot your phone in recovery (up button when the led is purple or violet)
-The led became gold color
- You now are (normaly) in cyanogen recovery
-Wipe data/Factory reset
-Wipe Cache for avoid bugs
-Now the fun part
-Apply update select the ROM and after the GAPPS
-Reboot and enjoy !
If the screen is black for a while after boot it's normal it's the system update
I also recommand you to take the
FXP-cm-12-20150412-UNOFFICIAL-seagull.zip
file because the other in cm12.1 are bootlooping
Now you can enjoy properly without camera and 3G/4G cyanogen
Sorry for my english I'm just a 14 french kid
btw, is this for 5102 or 5103? also, what do I have to be installed on my computer so I can flash boot for fastboot?
vmlc said:
btw, is this for 5102 or 5103? also, what do I have to be installed on my computer so I can flash boot for fastboot?
Click to expand...
Click to collapse
This is for D5103 the D5102 isn't the seagull this name is ONLY for the D5103
For the manipulation you will need emma (called flashtool by sony,for updating the bootloader)
And flashtool by Androxyde (this only is for flash kernel)
:highfive: now you're ready
Enjoy cyanogen on our t3 :laugh:
fastbooking said:
This is for D5103 the D5102 isn't the seagull this name is ONLY for the D5103
For the manipulation you will need emma (called flashtool by sony,for updating the bootloader)
And flashtool by Androxyde (this only is for flash kernel)
:highfive: now you're ready
Enjoy cyanogen on our t3 :laugh:
Click to expand...
Click to collapse
Im having problems flashing the kernel. I cant find my device in fastboot, and when I use flashtool to go ADB mode it says I dont have usb debugging on because I installed zip from recovery, the seagull file...
vmlc said:
Im having problems flashing the kernel. I cant find my device in fastboot, and when I use flashtool to go ADB mode it says I dont have usb debugging on because I installed zip from recovery, the seagull file...
Click to expand...
Click to collapse
Ok let's start off zero
you installed the zip via the philz recovery and after you wanted to flash the kernel ?
dan15 said:
Cyanogen ROM are distributed in zip format, so you have to :
- push the zip file to your sdcard
- you need a kernel with recovery (for the time being, the Philz one)
- you enter in recovery mode
- you select "install zip" and the zip file.
once it's finished, install the right kernel
for that, on your PC, extract the boot.img file from the ROM zip file and flash it with flashtool or fastboot
reboot and enjoy
Click to expand...
Click to collapse
thats what it says...
vmlc said:
thats what it says...
Click to expand...
Click to collapse
follow my tutorial it's the steps i followed and it works for me :good:
fastbooking said:
follow my tutorial it's the steps i followed and it works for me :good:
Click to expand...
Click to collapse
I got bricked meanwhile. Battery problem I think, not the first time...
ok, i think there is a missunderstanding.
in order to flash the kernel, you need to be in fastboot mode (with the blue light). so, once you have installed the zip file, shut down the phone (in recovery mode, select "power options/power off" , disconnect the phone and reconnect it in fastboot (maintain the vol up before and during the USB connection ).
you can now use "flashtool" (the Androxyde's one. to avoid confusion, the Sony's one is called EMMA or if it is more easy for you fastboot.exe
to use fastboot, you open a command line (Windows+R + type "cmd") , you go to the folder where the boot.img is and you enter the comand "fastboot flash boot boot.img". after ~2s the kernel is flashed, you can disconnect the phone and restart.
the first time, the boot time is about 5 min with a black screen after the animated screen, so wait a moment.
it's for that it's very important to have a well charged phone (min 40%) because the first start use a lot of battery, and you can't see anything.
I want to restore, I just installed the zip. Why cant I enter recovery?
edit: ok, I entered cyanogen recovery. will try to boot now. but I dont have backup/restore option....
edit2: ok, It booted but I still want to know how to back to previous version...
vmlc said:
I want to restore, I just installed the zip. Why cant I enter recovery?
edit: ok, I entered cyanogen recovery. will try to boot now. but I dont have backup/restore option....
edit2: ok, It booted but I still want to know how to back to previous version...
Click to expand...
Click to collapse
go on emma and select the android 4.4.4 update KK in the services line under open devices TA
It will restore the like the 1 st day but you will loose your data, but after you can install the philz recovery and restore the backup
Hey Guys,
After following all the steps properly with caution i was able to make the stock rom in a CWM recoverable file
I AM NOT RESPONSIBLE FOR ANY DAMAGES MADE TO YOUR DEVICE IF YOU MAKE A MISTAKE IN BETWEEN
BUT I WILL ASSURE YOU THAT I WILL TRY MY BEST TO HELP YOU
This are the files that were backed up , just check to be sure you have all files in the folder / zip
~ System . ext4 . tar
~ Recovery . img
~ uboot . img
~ Boot . img
~ nandroid.md5
TUTORIAL
Step 1 : Unlock Bootloader to flash CWM / TWRP recovery
GUIDE : UNLOCK BOOTLOADER
RECOVERY : DOWNLOAD
I DID NOT MAKE THE FILES TO UNLOCK BOOTLOADER : EVERYTHING WAS DONE BY :
SALMAN986 AND PRIYANSH21
I recommend using cwm
STEP 2 : Extract the stock rom to CLOKWORKMOD/PHILZ/TWRP in sdcard/sdcard1
IF YOU CANT FIND THIS FOLDER > YOU CAN BACKUP YOUR ROM AND CANCEL IN BETWEEN SO THE FOLDER IS CREATED AUTOMATICALLY
STEP 3 : select restore or advance restore
VOILA - The stock rom will be restored
WITH ROOT (KINGROOT) AND BUSYBOX
IF YOUR DATA IS NOT INTACT / PHONE DOESNT REBOOT , CLEAR DATA & CACHE FROM RECOVERY
BE SURE TO LIKE MY WORK , AND HIT THE THANKS BUTTON
MAIN CONTRIBUTORS:
SALMAN986
PRIYANSH21
PLEASE LIKE THEIR WORK TOOO , WITHOUT THEM WE COULD NOT HAVE THE TAIWAN STOCK ROM FOR OUR DEVICE
DOWNLOAD STOCK ROM HERE:
MEGA
Hey, you can do as follows:
~~~~~~~~~~~~~~~~~~~~~~~
Requirements:
* PC
* CWM/TWRP Backup
* CWM/TWRP Installed
* Winrar/7Zip
* Brain
Now the real-deal..
1. Copy the backup from Phone to PC
2. Extract system.ext4.tar file with winrar/7zip, you
will get the system folder
3. Collect the boot.img from the backup
4. Now collect a META-INF folder from any custom
rom/small update zip which is made for HTC Desire 526G+
5. Now select META-INF,system & boot.img, click
right button of your mouse and select 'Add to archive'
now select archive format 'ZIP' and press ok
6. Your flasable zip rom is ready. Just copy it
to your sd card and flash with CWM or TWRP
7. Done!! This will flash the stock Taiwan System to your device.
Make sure to hit the thanks button!!
P.S. Can you give the link for Indian Stock ROM.
Thanks.. i followed the procedure suggested by you. Really it is working. Is there any possibility to edit the source code and (As per my customization) compile, generating the images and flashing back. If yes which cross compile tool is required and how to get source code.
Philz touch recovery download for STEP 1 , Instead of using CWM / TWRP
Mega