Related
Hi, guys i just thought that when we mess up our galaxy y then we have to search again and again, separately for root file, stock firmware and odin so i bring to you a complete file that contains the stock firmware, the root file, and odin also. it is a rar file and none of the components have been created by me.
Credits:
stock firmware: doky
odin: google
root file: i don't remember sorry
guide for new ones:
stock firmware recovery:
1)get ur mobile to download mode or odin mode by shutting down and then pressing vol down + power button + home button. then press vol up when the warning comes ( don't worry nothing will happen )
2)connect mobile to pc and open odin. make sure u have mobile drivers. get them by installing kies.
3) click on pda and choose the file pda_s5360_dxlc1. now on csc and choose the file csc_s5360_dxlc1. now on phone and choose modem_s5360_dxlc1.
4) check auto reboot and f.reset time but make sure to uncheck all others. click start. if pass comes written on one of the upper boxes then it's done.
root guide:
1)shut down mobile.
2)get to recovery by pressing vol up + power button + home button.
3) choose install from sd card and choose direct root file.
4) it is done
5)reboot
get it here: here
just to let you know its not a good idea for people from europe to flash that stock firmware - its Indonesia, Malaysia, Philippines, Singapore, Vietnam firmware
its also out dated
you also dont need kies to instal the drivers - there is a usb drivers file from samsung which is much smaller so unless you actually use kies there is no need for it
later firmware and firmware for other countries can be found
http://forum.xda-developers.com/showthread.php?p=48462297#post48462297
I ThinK
xday123 said:
Hi, guys i just thought that when we mess up our galaxy y then we have to search again and again, separately for root file, stock firmware and odin so i bring to you a complete file that contains the stock firmware, the root file, and odin also. it is a rar file and none of the components have been created by me.
Credits:
stock firmware: doky
odin: google
root file: i don't remember sorry
guide for new ones:
stock firmware recovery:
1)get ur mobile to download mode or odin mode by shutting down and then pressing vol down power button home button. then press vol up when the warning comes ( don't worry nothing will happen )
2)connect mobile to pc and open odin. make sure u have mobile drivers. get them by installing kies.
3) click on pda and choose the file pda_s5360_dxlc1. now on csc and choose the file csc_s5360_dxlc1. now on phone and choose modem_s5360_dxlc1.
4) check auto reboot and f.reset time but make sure to uncheck all others. click start. if pass comes written on one of the upper boxes then it's done.
root guide:
1)shut down mobile.
2)get to recovery by pressing vol up power button home button.
3) choose install from sd card and choose direct root file.
4) it is done
5)reboot
get it here: here
Click to expand...
Click to collapse
Well You Should GaVe The Original 2.3.6 For Every Country
It They Install ThiS Via odin in other countrt They Wont Be Able To Regain Back Warranty.
Well I also Think ThaT There Are Many Threat About This Topic Already.
Thanks
sent from terminal emulator
Hi, Just like the title says, I have the 10.5 tab, I'm currently on the us ota for 5.0.2 rooted. I was wondering what the best and safest way to downgrade was? I'm having alot of problems with 5.0.2. I mean it runs smoothly and everything it's just alot of the games i play that worked great on kitkat no longer work on lollipop they just crash when i try to open them. Also there is no wanam xposed for 5.0.2 yet which is also a bummer. any advice or a steering in the right direction would be greatly appreciated as I don't want to try to do it without knowing what im getting into and make my nice little tablet a brick. thanks for your help.
Just flash the stock Kitkat 4.4.2 firmware
Sent from my SM-T805 using XDA Free mobile app
Don't fret. I am a total noob too. I got the following information from a different site, Unfortunately I cannot post the link as a noob. Once I have enough post count, I will add the link to the source (fairness to the author of the source).
How to flash Samsung Stock Rom using Odin
Home > Tutorials > Last update on February 1st, 2015
These are the instructions to flash Samsung Stock ROM (original firmware) using Odin on Windows Computer.
Requirements: Your Samsung device should have at-least 30-40 percent of phone batter to perform the flashing process.
Flash Samsung Stock Rom using Odin
Step 1: Download and install Samsung USB Driver on your computer. In case you have already installed the Samsung USB Driver on your computer then Skip this step.
Step 2: Download (Stock ROM compatible with your device) and extract it on your computer. After extracting you will be able to see these kind of files:
T800XXU1ANJ6_T800XAC1ANI1_HOME.tar.md5
Step 3: Now, Enable USB Debugging on your Samsung Galaxy Device. To enable USB Debugging: Open Settings > Developers Option > USB Debugging > Tick to enable.
(Developers Option is hidden for Android 4.2.2 or above, to show the developer option Go to Settings > About Phone > Built Number (Tap on it for 5-8 times).
Step 4: Power Off your Samsung Device.
Step 5: Now, you have to boot into Download mode. To boot into Download Mode: Press and Hold Volume Down Key, Home Key and Power Key. When phone vibrates Leave the Power Key but Keep holding the Volume Down Key and Home key. You will boot into the Download Mode.
Step 6: In the Download mode you will be able to see a Warning Yellow Triangle Sign. In this situation you have to press the Volume up key to continue.
Step 7: Download and extract Odin on your computer. Use Odin 1.85 (Successful in downgrading to KitKat from Lollipop)
Step 8: Now, Open Odin3 and connect your phone to the computer.
Step 9: Once you have connected the phone to the computer, Odin will automatically recognize the device and show “Added” message at the lower-left panel.
Step 10: Once your device is detected by Odin, click on the “PDA” (or AP) button and select the tar.md5 file that you have extracted in Step #2.
Step 11: Now, click on the “Start” button in Odin to begin the Flashing process.
Step 12: Once you see, the Green Pass Message then remove the USB cable from the device (during this process, your device will restart automatically).
Step 13: Your Samsung Device will now stuck at boot (boot loop). Now, You have to boot into Stock Recovery Mode, To Enable Stock Recovery mode: Press and Hold Volume UP key, Home Key, Power Key. When phone vibrates Leave the Power Key but Keep holding the Volume UP Key and Home key. You will boot into the Recovery Mode.
Step 14: In Recovery Mode, Wipe Data/factory reset.
Step 15: Once Cache Data is cleared, Select Restart Phone Now from the recovery menu.
Step 16: Now, your Samsung Device will restart without any issue with the Stock Rom you have flashed.
I ran into problems flashing the ROM twice and I went into a complete panic (could be Odin 3.10, or corrupted ROM). My region is XAC. Initially I tried XAR, and failed miserably. Eventually I downloaded the XAC ROM from a different source (SamMobile), also using Odin 1.85 instead of 3.10. Everything went smoothly (with the above stated boot loop). Should you get a Fail message in Odin, use the instructions from droidviews (do a web search on droidviews and "firmware-upgrade-encountered-an-issue-solution". Again, I will post the link once my post count is slightly higher.)
Step 3 is not required at all. Odin 3.10 should work fine.
As for factory reset, that shouldn't be required, that should be a last resort. Just wipe cache partition. I would simply install twrp for this.
It should then boot.
Work only on Oreo 8
You must be Stat Normal
Oem Unlocked
Enable USB Debugging Mode and OEM Unlock in your mobile. To do this; go to settings >>> about >>> Tap on the “Build Number” 7-10 times consistently to enable “Developer Options,” then go to the “Developer Options” and enable USB Debugging Mode and OEM Unlock. There is no complicated process in the Samsung Galaxy J7 Duo.
Download and install the Samsung USB driver to your computer system.
Also, download the ODIN software. Select above Oreo version in the ODIN list. Install ODIN in your PC.
Download Magisk.Zip (Download Latest version) and forced encryption disabler, Copy it to Your Phone Memory. We Need to flash encryption disabler to avoid Boot Warnings in the future after the Root process.
Download and save the TWRP File. Select Correct TWRP file from Below. This TWRPs can support Up to Oreo.
SM-J720F
SM-J720M
Flash TWRP using ODIN
Samsung Galaxy J7 Duo Download Mode
Connect your USB Cable with PC. Switch off your device. Then, enter into Download mode. To do this; press and hold down the Volume Down + Home + Power buttons and connect your micro USB Cable.
Samsung Galaxy J7 Duo Download Mode Warning Screen
Press the Volume Up button to continue when you see the warning message.
Now, connect the Samsung Galaxy J7 Duo mobile to the computer via USB cable.
Launch the Odin app on your computer. If the device is detected by this app (Odin), it will show you a message that reads – added!!!
ODIN Added Message
However, if the device is not correctly connected to the PC, you won’t see this message. So, you have to check the USB cable if it is reasonable and reconnect the device.
After connecting the Samsung device, click on the PDA/PA button to browse/search and get the TWRP from where you saved it on your PC. Also, navigate to “options” and tick the Auto Reboot.
Odin Auto Reboot
Click on “Start”
Once the file is loaded into the device, reboot your device.
Kudos, you have just Installed the TWRP on your Samsung Galaxy J7 Duo. If you installed TWRP, Don’t turn on your mobile. Immediately, move to Magisk Installation steps.
You should not Boot into Normal OS Booting, after TWRP. After TWRP Flash, Immediately Boot into Recovery or twrp will gone
Boot it Into recovery mode->Volume Up + Power Button.+Home
Now it Will Boot into TWRP Recovery Mode.
Install Magisk, forced encryption disabler in your Samsung Galaxy J7 Duo using TWRP
Select Wipe->Advance Wipe->Select Cache Data.
Return to Home of TWRP select Install.
Select Magisk.Zip.
After Installation again Navigate to Home select Install. Select forced encryption disabler.
After the Installation Reboot Your Mobile.
You can also install Magisk.apk in your Mobile Applications. Forced encryption disabler is used to avoid the boot loop issue after rooting.
enjoy
SM-J720F
SM-J720M
encryption disabler
Samy6699 said:
Work only on Oreo 8
SM-J720F
SM-J720M
enjoy
SM-J720F
SM-J720M
encryption disabler
Click to expand...
Click to collapse
Can it be used on the Dual-Sim version SM-J720F/DS released in 04/2018 ?
Can i install it on Galaxy J7 Duo running Android pie
Nitin devarasetty said:
Can i install it on Galaxy J7 Duo running Android pie
Click to expand...
Click to collapse
i also need that man.
Please make one thing clear
Do we have to turn off "Auto reboot"
Or keep the "Auto reboot" option checked on?
Android 9.0
Hello, when it will be possible ? If never, why ?
I followed the exact process but everytime i tried to boot into TWRP recovery immediately after the flashing, the device still boots into stock recovery instead of TWRP
Please help me with this
Thank you
I figured out a way to root the Galaxy J7 duo
Actually i have tried lot of ways to root using TWRP flash and all.. but one day i accidentally bricked my device
So i downloaded the stock ROM to flash my device
And i downloaded the 8.0 android ROM
So this root method basically tested on android 8.0
So now i have android 8.0 stock ROM downloaded
Step 1 -
So make sure you also downloaded the ROM
And extract the ROM file (you must have got the "AP" "CP" "BL" "CSC" and "HOME CSC" file)
Then copy the "AP" file in your phone
Then install magisk manager in your phone
Open magisk, select install, select and patch a file from magisk
Then select "AP" file
And wait while magisk is patching the "AP" file
When flashing is done the patched file will be saved on storage, emulated, 0, download (file will be saved as "magisk_patched.tar")
Then simply copy the patched file in your computer
Step 2 -
Open odin in your Computer
In odin, select "magisk_patched.tar" in "AP" section
Select "BL" from the stock ROM folder in the odin's "BL" section
Select "CP" from the stock ROM folder in the odin's "CP" section
Select "HOME CSC" from the stock ROM folder in the odin's "HOME CSC" section
make sure you select all the official files from the stock ROM folder... just instead of the "AP" file, select the "magisk_patched.tar"
Then connect your phone via USB cable
Odin will detect and show "added" message
Start the flashing process
It will take few minutes
When its done your phone will boot up
But it will show something like "erasing" and "verification unsuccessful"
Just agree with that and erase the phone
(It will cause a data loss because everything will be deleted and your phone will reset, so i suggest to make a backup using samsung smart switch)
Then when your phone will reboot, just follow the steps to setup
Amd install magisk latest apk
Open magisk and boom!
You can already realize that magisk root is activated
Amd magisk will ask you to "setup environment"
Just agree and your phone will reboot withing 5 seconds
And done!
Your phone is now rooted
Install root checker and verify your root status
how to un-brick
Same thing here,
Tell me how you un-bricked your phone
I bricked my phone by installing wrong twrp file to sm-j720f android pie with odin
and now it shows only bootloader screen and I can't even go to recovery mode or home screen just showing " SAMSUNG GALAXY J7 DUO secured by Knox powerd by android" noting else
That is exactly what was happened in my phone
So what i did just downloaded the Stock ROM for J7 duo from the sam mobile website.
Then extract the ROM and you will get few files ("AP", "BL", "CP", "CSC", "HOME CSC")
Then boot your phone into download mode using this method
(Connect the phone to your PC using USB cable, then press and hold Power + volume down + home, then when the "powered by android" logo appears release only the power button... so your phone will boot into download mode, press volume up to continue)
Now, in odin you can see "added" message that means device is connected
Now select the ROM files respectively, BL, AP, CP, CSC
Then click start, and the process will start, will take few minutes
When done, your phone will boot normally
Yeah everything is right until...
[grand_theft;83142325]That is exactly what was happened in my phone
***********
So what i did just downloaded the Stock ROM for J7 duo from the sam mobile website.
Then extract the ROM and you will get few files ("AP", "BL", "CP", "CSC", "HOME CSC") *********
Then boot your phone into download mode using this method
Fact that I cant even go to download mode I tried out many times
Just follow this step
(Connect your computer with your phone using USB cable, then press and hold Power + volume down + home, then when the phone vibrates and appears the samsung logo again just release only the power key, while holding the volume down and home key)
(Just release only the power key when the "powered by android" logo appears)
Thats how you can go to the download mode
No virtual change
Done it as u say,
But my mobile shows noting but just logo screen
*****SAMSUNG GALAXY J7 DUO secured by Knox powered by android*****
again and again
These is not first time, last I did the same mistake before and I went to Samsung service store they recovered it, I don't know how they did but it worked.
These time I want to (tring to) do it on my own bcoz I love playing with ROM's, root, etc.
Thanks for replys
I also did the same mistake by flashing wrong TWRP
But however i managed to enter into downlod mode following those steps
And flashed official ROM to unbrick the phone
You must go into download mode to flash the official ROM using odin
Thanks alot
Thanks man,
I'm able to enter download mode and I installed official ROM. Now in using it as normal but (1)Secure folder and Pay mini are not working.
(2)Do you have any idea on other ROMs that works on SM-J720F other than Samsung's one UI.
(3)can I install android 8 on it in ordered to root as you said it in previous post.
(4)from previous your post on oreo twrp explanation, is twrp works fine. What happens to twrp if I update phone to Q (from system updater)
I'm glad you made it!
Now,
1) Secure folder and pay mini won't work because the phone thinks you rooted your phone and maybe your binary is cracked (so forget using those)
2) I'm not sure about any ROMs which is stable with this model. But you can search the internet (I think pixel ROM is pretty popular)
3) I'm not sure if my process of rooting supports android 9.0 or not, because i personally tetsted it on 8.0, So you can download the oreo ROM from the internet and then follow all the steps i mentioned before
4) If you want to install TWRP, you can still install TWRP after rooting via the method i provided
(You can install TWRP using flashify on a rooted phone)
But if you want root access then you can simply root your phone first..
And whatever custom ROMs you want to install, install it using flashify
Because if you update software via official OTA, the root access and TWRP both will be gone
And if you root your phone, then however you won't be able to perform a official OTA update.
(First root your phone, then simply download your TWRP file and flash it with root permission within your phone)
Instated of Oreo AP file,
grand_theft said:
I figured out a way to root the Galaxy J7 duo
Actually i have tried lot of ways to root using TWRP flash and all.. but one day i accidentally bricked my device
So i downloaded the stock ROM to flash my device
And i downloaded the 8.0 android ROM
So this root method basically tested on android 8.0
So now i have android 8.0 stock ROM downloaded
Step 1 -
So make sure you also downloaded the ROM
And extract the ROM file (you must have got the "AP" "CP" "BL" "CSC" and "HOME CSC" file)
Then copy the "AP" file in your phone
Then install magisk manager in your phone
Open magisk, select install, select and patch a file from magisk
Then select "AP" file
And wait while magisk is patching the "AP" file
When flashing is done the patched file will be saved on storage, emulated, 0, download (file will be saved as "magisk_patched.tar")
Then simply copy the patched file in your computer
Step 2 -
Open odin in your Computer
In odin, select "magisk_patched.tar" in "AP" section
Select "BL" from the stock ROM folder in the odin's "BL" section
Select "CP" from the stock ROM folder in the odin's "CP" section
Select "HOME CSC" from the stock ROM folder in the odin's "HOME CSC" section
make sure you select all the official files from the stock ROM folder... just instead of the "AP" file, select the "magisk_patched.tar"
Then connect your phone via USB cable
Odin will detect and show "added" message
Start the flashing process
It will take few minutes
When its done your phone will boot up
But it will show something like "erasing" and "verification unsuccessful"
Just agree with that and erase the phone
(It will cause a data loss because everything will be deleted and your phone will reset, so i suggest to make a backup using samsung smart switch)
Then when your phone will reboot, just follow the steps to setup
Amd install magisk latest apk
Open magisk and boom!
You can already realize that magisk root is activated
Amd magisk will ask you to "setup environment"
Just agree and your phone will reboot withing 5 seconds
And done!
Your phone is now rooted
Install root checker and verify your root status
Click to expand...
Click to collapse
************************************************************************************************************************************************************************************************************************************************************************************************************
Ok I agree with you,
But what if I replace Oreo's AP file with android 10's AP file(which I installed recently on my phone), will it boot with root or not.
************************************************************************************************************************************************************************************************************************************************************************************************************
I have not tested this method on any other android version, you can still try it on your own, there is nothing to lose, just make a backup before flashing. If you succeed then that's great
But i have personally tested this method only on android 8.0
(Before doing anything, just make a proper backup using samsung smart switch. So you can restore your important data)
Success
Replaced with android 10's AP file and flashed with Odin. Now my phone has rooted with Magisk manager.
Any suggestions to tweak android
Claudio4780 said:
Can it be used on the Dual-Sim version SM-J720F/DS released in 04/2018 ?
Click to expand...
Click to collapse
Have you ever got the answer or figured it out? I've got the same model and I cannot find anything on the net to help me with rooting this phone.
READ EVERYTHING CAREFULLY!
1.Your phone warranty will be void after this tutorial!
2.Any small mistake and your phone is bricked/bootlooped!
3.All of your data will be lost so back it up somewhere
Click to expand...
Click to collapse
(Fixed the tutorial my bad.)
Click to expand...
Click to collapse
Hey Guys Im Back! Thank you for the support and how it blew up. I have tested this on Android 10 UI 2.0 and it works better then ever!
Also installed lineage os : https://forum.xda-developers.com/galaxy-a10/development/rom-lineage-os-a10-a105f-t4078093
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download TWRP and 2 other important files
1.Dial *#1234# and it will show the AP and some others, focus on AP paste it on google and get the download for it
2.After downloaded move the AP to your download folder in your android device
3.You will get a magisk_patched.tar after its been offically converted
4.Get the twrp for a10
Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.After you got everything open the .tar archive and extract vbmeta.img, boot.img and you should already have recovery.img on your Desktop
6.Grab all the 3 .img files and archive them into a .tar using 7zip, Now continue to step C,
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find Desktop.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
i notice thread title says exynos only.. u do know they are all exynos including a102u and a102u1 right?
Oh. Alright thanks for telling me.
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Cupcake 1.5 said:
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Click to expand...
Click to collapse
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
cmz6996 said:
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
Click to expand...
Click to collapse
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Oh! Im happy to hear that!
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
cmz6996 said:
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
Click to expand...
Click to collapse
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Cupcake 1.5 said:
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Click to expand...
Click to collapse
Alr thanks.
Can you upload it to Mediafire? Mega marks a "temporal error"...
Kyua said:
Can you upload it to Mediafire? Mega marks a "temporal error"...
Click to expand...
Click to collapse
At me it works?
Works on a105m?
Axeggus said:
Works on a105m?
Click to expand...
Click to collapse
Yes
i receive message that i running samsumg not official firmware after odin install recovery.tar
not work
cmz6996 said:
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download Your firmware and TWRP
1.Go in your calls app and dial *#1234# Then You will receive some details about your AP, CP etc. look at the AP then download the firmware by searching it on google and (download it from sites like sammobile etc)
2.After you got your firmware connect your device to your pc after its connected send the entire firmware to the device in the Downloads folder
2.1. Install Magisk Manager
3.After you're in magisk manager press on install (first one) then press install again then press Select and Patch a File
3.1.Chose the firmware you saved on the Downloads folder
3.2.After you tap on it it should've already started modifying it
4.After it finished go back to your pc and move the magisk_patched.tar back to your desktop (It should be located in Downloads)
5.From the magisk_patched.tar extract boot.img and vbmeta.img to your desktop
5.1.Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.2.After recovery.img(TWRP) has been downloaded move it to your desktop
5.3.Select all those three items(vbmeta.img,recovery.img,boot.img) right click then Find 7Zip then press add to archive
5.4.Rename the Archive name to recovery.tar and make sure the archive format is .tar
6.After the Archive has been downloaded follow the steps in C
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find recovery.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
Click to expand...
Click to collapse
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
andrea2o18 said:
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
Click to expand...
Click to collapse
You installed the wrong fir.ware check your right firmware.
BlueFolks said:
i receive message that i running samsumg not official firmware after odin install recovery.tar
Click to expand...
Click to collapse
Be cause you modified the firmware ignore that message
have you fixed the storage reduced to 16gb problem?
I have a Samsung galaxy sm-a10. I've tried everything here, even combination files. The error I ALWAYS get is 'failed flashing ROM... OEM lock'
Of course I have unlocked OEM in developer options, but still I get this error in the bootloader.
Any ideas?
So successfully you have rooted your device and you just messed up the system partition by tweaking some of the build props lines and all. Now you are stuck in the boot logo that is nothing but boot loop so as far there is no TWRP recovery for this device. So the only solution you have got is to totally re flash the ROM into the partition. Wait a minute we've got a new trick to restore the corrupted system partition.
without having to flash the whole firmware you can just follow this tutorial and fix your brick Samsung F62 device.
❄Requirements
1. Windows computer or any Odin supported device for flashing
2. Latest Samsung Odin
3. Extracted system image of Samsung F62 (super.img.tar you can get it from this thread)
4. Hell lot of patience to get back your device
Downloads(Mediafire)ODIN FOR F62/M62
Rose in Samsung Galaxy F62 / M62 | OFFICIAL
t.me
super.img.tar
Procedure Booting the device into download mode
As your device is in a boot loop condition or stuck it logo you just need to hold the volume down and power button until the screen goes off then immediately you should connect the cable to the PC and device then immediately press volume up and down so that you will boot into download mode.
If you are confused then just follow this video tutorial. After booting your device into download mode just press volume up button to continue.
Boot into download mode tutorial
ODIN & flashing system without losing data
After setting up the Odin in your computer just launch the Odin and ensured that device is connected and displayed in the Odin.
now just place the downloaded super.img.tar ( download from this thread) of Samsung F62 device in the Odin AP column.
now after placing the super.img.tar on AP column of the Odin, now press the start button to start the flashing process.
now just wait until the flashing is done. don't disturb the device or cable.
you can see the flashing process in the Odin.
your device will be automatically restarted after flashing.
repeat this process whenever your device gets bricked.
This is the only method to restore the system without losing of personal data as we don't have TWRP recovery this is the only way to restore the system without losing data.
i hope this helped you out guys
now you can safely tweak your system partition.
End linesi'm new to this thread writing.
This is my first biggest thread on my favorite device
my mom just gifted me this flagship device And I just love to tweak this device and I also love to help others from getting out of tough situations
The super.img is extracted from the official firmware and converted to super.img.tar by me and i personally tested this on my device so you can follow this method safely.
This tutorial is done by me & didn't copy it from anyone.
You can also just extract the super.img from the firmware and convert the image to .tar using this 7 zip software in windows 10.
I hope this tutorial helped you out and feel free to reply to this thread.
Just thank me and that will be the biggest appreciation for me
@rc chanu I've changed the prefix of your thread from "Development" to "How To Guide" as the thread didn't qualify for the first one. Please review the sticked guidance prior to your next posting and don't change the prefix back. Thanks for your cooperation.
Regards
Oswald Boelcke
Senior Moderator