[Q] Xperia play having problems starting - Xperia Play Q&A, Help & Troubleshooting

So my Xperia Play (CDMA) has been fine until earlier today, i had the phone on, but then when i try to wake the device, it won't wake, but the device is still on cause cause some buttons cause vibration and the back light is on, just nothing on the screen.
so i go to reboot the device, now i can't even get it turn on. i hold down the power button and it briefly starts up (no boot screen) then the led flashes green/pink/blue then stops trying, back light stays on. i keep trying still same thing. can't even get it into fastboot mode. the battery is fully charged (plugged it into a charger.) and I was last using fxp cm9 rom with lupus kernel.
after repeatedly unplugging device, removing battery, i got it to display the battery charging screen. but when trying to get out of that screen i get the whole not turning on thing again. and i should say i can tell the back light is on.
once in a while it will connect to the computer and then i can access the logcat, which is right here: http://pastebin.com/FiJFrEGE
the only thing that causes entries to write to the log is by opening/closing the touchpad.
I am very confused what the whole green/pink/blue led light is about, and why this issue is happening, is it kernel related, rom related, or hardware related, i have no idea. i'd appreciate any help i can get on this or if anyone else has had this issue. thanks.

Try flashing a stock FTF from flashtool. Might make things go back to normal.....

When I was using CM9 I use the included FXP kernel, so maybe thats why you're having a problem. Or perhaps the Lupus kernel you flashed was a GB build opposed to ICS.
Flash stock FTF an re try.

Thanks for the replies, I'll try to install a stock ftf. Also I do know which lupus kernel is which at the moment I'm running the cm10 blend with jb lupus kernel since i got the device to boot after x tries.
Sent from my ADR6400L using Tapatalk 2

Related

[Q][PRO] Dead phone, it never boots, i woke up to find it like this,

it was normally working at night. I turned off the screen and went to sleep. the battery was about 90%
When i woke up,i found that the screen was lit. it was a little dark blue-ish. The phone did not respond to anything i do !
I made a battery pull and tried to reboot. the same dark blue-ish screen appeared again, the kernel's logo never shows up. i tried to charge it for a while then turning it on. the kernel's Logo appeared. I can now access both CWM and TWRP. but when it's turn for the boot animation. the dark blue screen pops in again
any ideas ??
Specs: Xperia Pro
ROM: Ultimate HD v2.0.3
Kernel: E-kernel (the dual recovery one)
MODS installed:
uHD MOD v2.4
Cybershot
walkman
Recharge it for a while
Try to clead cache and dalvik, fix permissions, try to boot
If it dont work, then change your kernel and try to boot.
If it dont work, revert back to a old backup or flash a stock rom
Thanks for your help.
I fixed it by formatting the system partition and reflashing the rom.
Now it's all good
if at some point the kernel logo doesn't show up, I'd put my two cents on the kernel for an issue... just saying... but as long as you are able to still connect the phone in fastboot mode, you can always try flashing a kernel to recover it.
Just saying. ... good you figured it out.
atmos929 said:
if at some point the kernel logo doesn't show up, I'd put my two cents on the kernel for an issue... just saying... but as long as you are able to still connect the phone in fastboot mode, you can always try flashing a kernel to recover it.
Just saying. ... good you figured it out.
Click to expand...
Click to collapse
I don't think it was a problem with the kernel.
At first the kernel's logo didn't show up because the mobile was low on battery. The screen was lit the whole night. When I charged it a little the kernel booted normally and I accessed recovery without any issues.
I really don't know what the heck happened.
The only thing the mobile should do at night is backing up apps with titanium backup.
I'll try to see if any apps didn't get backed up. Maybe it hangs on a certain app...
Sent from my Sony Xperia Pro using Tapatalk 2

[Q] Is it bricked?

So I flashed a JB backup and then the kernel with fastboot, and the screen would shake from side to side nonstop whenever I wasn't touching it. So I pick up my laptop to flash a new kernel (old one must of been corrupted, I assumed) and I drop the damn thing when it's turned on. I'm pretty sure that it messed up the HD files to where fastboot was messed up (it would force close when I tried a command) So I found another application to flash a kernel, but it said I wasn't rooted. So I, desperate, hit the delete kernel button. When I tried booting, sometimes the red light would flash three times,other times nothing.
I have since gotten a new phone (was already due for an upgrade) but as a hobbyist, I'd like to try to fix my old phone to maybe give it to someone else.

[S/SL/AS/Ion]General bricked device thread

So, I've been seeing A LOT of threads regarding bricked devices (be it soft or hard bricks). So, I decided to create this thread, so everyone with bricked devices post here for help, instead of filling our forums and XDA servers with a load of topics with the same stuff.
If someone knows of a general unbricking thread, please PM me or tag me with a link so I can post on this post.
I will PM a mod to pin this thread to top.
To all brickers,
Before posting, try this thread:{RECOVER SOFT-brick}[2012 XPERIA's]Recover ALL 2012 XPERIAs from SOFT-brick
Remember to give the author thanks
Xperia S Return Back To Stock!
Pre-Requisites
For All The New Users..
If You Did Something Wrong
If nothing is working out
Not Able to Fix
Need to Return Back To Original Firmware?
Here is the Guide For You
Click to expand...
Click to collapse
Return Back To Stock
GUIDE for Better Understanding With Pictures And Images For New Users
Explained Step By Step
Click -- [HERE]​
Just a tip: Try downloading Sony Update Service and following the instructions if you get a green LED blink on your phone, which is way simpler to recover without any problems.
Guys My ION LT28h got bricked during a recovery using CWM.
First It was a soft brick, i did something , random pressing of buttons made it worse. its on HARD BRICKED STATE now. Its been more than 5 weeks.
So after some research i found out that my Kernel is ****ed up. My phone is Boot loader Locked, so i cant flash the Kernel separately.
Now few of our fellow xda members told me to unplug the battery cable from the motherboard.
I have successfully disconnected the battery cable from motherboard, i kept it disconnected for one whole night.
Whats the next step ?
Will i be able to flash it with flash tool after connecting the battery to motherboard back ?
Will i be able flash the busted Kernel to a working stock kernel ?
Accidentally messed up and soft bricked Ion- LT28h.
xperia Ion LT28h
ROM: JB 4.1 Pure CyanogenMod Based on CM 10 FXP 218
kernel: GI Kernel v3 or v5
Recovery: TWRP and CWM
Rooted and Unlocked Bootloader
Hi guys, above mentioned were my previous settings. Had occassional reboots and sometimes it was kinda laggy that's why i decided to flash it to another ROM - supposedly to ParanoidAndroid. After following steps to install PA, my phone was on bootloops, was in a hurry then freaked out, i tried soft and hardreset, and tried booting on recovery both on twrp and cwm to flash properly as what was instructed however i may have flashed the wrong zips interchangeably with other roms and kernels resulting to a total messed up ion. i could have restored immediately to a saved CWM or TWRP backup right away however, i only stopped resetting when my phone suddenly stopped responding, no Sony logo, no Xperia logo, no boot, just backlight on, does not turn off, soft and hard reset no nothing. i guess until the battery went dead, then i charged it the whole night.
after reading most threads on recovering softbricked phone, mainly this {RECOVER SOFT-brick}[2012 XPERIA's]Recover ALL 2012 XPERIAs from SOFT-brick thread, and after a couple of days of red led, i constantly charged, i patiently waited(2days) still no green led, however i found out that i can access fastboot. (blue led).. i managed to get to this fastboot mode(blue led) ONLY after i soft reset or power+vol.up/1 vibrate the phone once the backlight lits up- on&off - for about less than a minute then it goes back to red led. (i'll be calling that stage as backlit-on&off-then-back-to-solid-red-led cycle) but then again if i go to fastboot, it will stay in fastboot mode during flashes and it stays there until the battery runs out and goes back to red led. then i charge my phone again, but
during fastboot mode, i have tried flashing the kernel, system and boot image. all via Fastboot command prompt.
and all were successful. there were combinations like, flashing only the kernel, tried flashing kernel and system, tried boot image only, tried all the same time, tried system only, tried different kernels, system and boot img, BUT STILL my phone wont even give me the sony logo screen.
then i thought i may need to wipe cache and userdata so i also erased cache and userdate a couple of times via fastboot mode command prompt. and yes fastboot does detects my phone. it can reboot to bootloader or just the normal fastboot reboot. so i have no issues regarding phone and pc via using fastboot command prompt. and Same thing - all flashes were successful,
i have flashed i think more or less than a total of 50 times, flashing different combinations. Still it goes back to brick mode.. backlit-on&off-then-back-to-solid-red-led cycle.
i'd like to add that i have also tried flashing via fastboot mode using Flashtool. (thunder icon+selecting 'fastboot mode'). i have flashed the kernel and system, tried kernel only, tried both same time, tried system with boot.img tried flashing kernel with boot.img too, tried different combinations. again, all were successful, but still same result.
it only goes back to backlit-on&off-then-back-to-solid-red-led cycle.
a couple of days after it went to green. flashmode finally! thinking everything will now be alright, i decided to flash it using flashtool via flashmode. I connected phone to pc, after the solid red led and after backlit-on&off-then-back-to-solid-red-led cycle. and the it goes back to red led then the backlit on&off cycle, after observing my phone for hours i then knew that after, i guess about a hundred cycle of backlit on&offs it really does go to green led by itself and if i'm connected to the pc and flashtool it stays on green led or flashmode, however if im connected only on a wallcharger it goes to green led but will only stay there for like 1-2 seconds then goes back to red led and then the backlit on&off cycle.
then i thought just maybe my battery really needs to die as mentioned, since upon plugging my phone on to a wall charger it goes immediately to red led and there's really no response on the phone except only if you gonna wait for the backlit on&off cycle the n press power + vol up then it will respond and go to fastboot mode or power+vol down which goes to flashmode. then i decided to reset the battery by carefully unplugging the ribbon cable and i did. well, initially it did (led was off for a moment then changed to blinking red then solid red) but i have to go to work that time and had to continue only after coming home from work, and that did not resolved it.
i may have flashed my ion a hundred times or so to this date, still no luck. i have finally decided to re-locked my bootloader- and yes it is successfully locked now. - thinking PCC/SEUS/SUS would get it back to life but i'm wrong - it just cant detect my phone. PC companion detects it as Phone/Tablet only then after selecting Ion on the phone list it always says my device is upto date and no available software. (sad)
I also noticed that flashtool does not detect my phone as LT28h. It only says that it is connected to flashmode. Is that an issue too. I have tried diff versions of flashtool from 9.6 to 9.11 all same. i have also installed fastboot and adb as well as flashtool drivers, it sayas all were successfully installed however if im connected via flashtool flashmode, none seems to be detected on device manager, tried reinstalling and manually installing the sony sa0103 adb interface driver however after installing i get an error unable to start device. even if my phone is connected still the device on devicemanager still has an excalamation point. i'm using windows 8. i have flashed successfully before when my phone was in good state, however now that im on brick mode it seems that all flashes i've done did not push thru. also those times that i have flashed my ion via flashtool it says something like:
phone should be connected with usb debugging on and enabled install on unknown sources. i have tried flashing it using win7 pc phone was not detected still, however flashtool stated and detected my device was connected on usb debugging mode, but have has errors during flashing though.
since my bootloader is now locked im unable to flash now via fastboot. before bootloader status says- rooted now bootloader status is- ROOTABLE.
i previously owned xperia neo and have managed to flash it successfully without any issues, also this is the 3rd time i had bricked my ion and managed to fix it before..
i also want to ask regarding flashing back to stock - does that mean any stock firmware can be selected? can be .233 / .68 /.20 or the latest ICS 6.1.E.3.7? coz i have basically tried to all of those mentioned. also is the reason that my flashes were not successful is it because i was currently on 4.1 JB ROM and im flashing 4.0 ICS stock? I also have TWRP and CWM backups on my PC and on internal SD card, is there a way for me to flash or restore those backups via flashtool?
I'm running out of options, i'm desperate and on the verge of giving up.
i dont want to believe that i have totally messed up and hard bricked my phone. I do believe that there is a solution to this, and my phone can be recovered without sending it over to repairshop.. Today is the 3rd week and still struggling to get my phone back to life (even just the sony logo) . any suggestions before i unlock again my bootloader? please help. Any help will be gladly appreciated, and many thanks to everyone for spending time on reading my messed up and soft/hardbrick ion experience.
If you brick your device while flashing kernel and device do not respond any way then follow this little difficult but 100% sure method.
- Dissemble your phone.
- Disconnect battery ribbon from motherboard.
- Reconnect battery ribbon.
- Fastly connect USB cable while holding vol +/-
- Flash Kernel or FTF FW.
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Droiiiiiiiiid said:
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Click to expand...
Click to collapse
Did you try SUS ? Official update service ?
Droiiiiiiiiid said:
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Click to expand...
Click to collapse
I think that you should charge it more to be able to go into flashmode. Maybe until the red light will go off or it'll turn into green. Then try to go into flashmode. Good luck
MozzieZ said:
Did you try SUS ? Official update service ?
Click to expand...
Click to collapse
I was going to but that requires my device be in Flashmode.
Droiiiiiiiiid said:
I was going to but that requires my device be in Flashmode.
Click to expand...
Click to collapse
Read this, maybe it will help you.
http://forum.xda-developers.com/showthread.php?t=2344896
This is my first time got hard brick on my phone. I'm flash wrong ROM (it made for S but I flash it on SL) now my phone totally dead. When I put on wall charger it show constant red led and off several minutes later, try disassemble phone and disconnect and connect ribbon doesn't help to get flashmode and fastboot mode. Any help would be very appreciated.
EDIT: After disconnect ribbon battery I got notification on flashtool "device connected with usb debugging off" but led remains on constant red. Should I try rubber band tricks?
ahlulnugraha said:
This is my first time got hard brick on my phone. I'm flash wrong ROM (it made for S but I flash it on SL) now my phone totally dead. When I put on wall charger it show constant red led and off several minutes later, try disassemble phone and disconnect and connect ribbon doesn't help to get flashmode and fastboot mode. Any help would be very appreciated.
EDIT: After disconnect ribbon battery I got notification on flashtool "device connected with usb debugging off" but led remains on constant red. Should I try rubber band tricks?
Click to expand...
Click to collapse
After disconnecting and connecting back the battery cable , you wont get access to flashboot/flashmode instantly. disconnecting the cable will reset the phone.
If you are getting red led means , its charging on low power. You should keep on wall charging for some hours , say 12 + hours.
After that try flashing the kernel alone , first . you will have to hold the flash mode button for sometime. say 5-10 minutes. then if u have enough charge in your phone it will flash the kernel alone. if u are successful in flashing the kernel, then charge again for some hours , 2-4 hours then try to flash the entire ROM.
Read the Thread Recovering Bricked Phones. This will help. I recovered my phone following the method shown in that thread.
Be patient bro, you can recover your phone, just that it will take some time
Captain Droid said:
After disconnecting and connecting back the battery cable , you wont get access to flashboot/flashmode instantly. disconnecting the cable will reset the phone.
If you are getting red led means , its charging on low power. You should keep on wall charging for some hours , say 12 + hours.
After that try flashing the kernel alone , first . you will have to hold the flash mode button for sometime. say 5-10 minutes. then if u have enough charge in your phone it will flash the kernel alone. if u are successful in flashing the kernel, then charge again for some hours , 2-4 hours then try to flash the entire ROM.
Read the Thread Recovering Bricked Phones. This will help. I recovered my phone following the method shown in that thread.
Be patient bro, you can recover your phone, just that it will take some time
Click to expand...
Click to collapse
Thanks for your fast reply, but I'm already put on wall charger 1 day, and the red led got turn off (no led at all). I think I'll try rubber band trick tonight and leave it till morning.
Hey guys I'm having a problem with my Acro S... It's bootloader is unlocked.
It was soft bricked due to a command I ran on Terminal Emulator (dd if=/dev/zero of=/dev/block/mmcblk0). After inputting that command I safely turned off the phone (Long press Power button, Choose Power off). After turning off, phone was completely dead, no response. It was on 80% battery for sure. It happened last week Saturday (July 20). I then charged my phone for 2days+. On the first day (July 21), no red LED appeared, on the 2nd day (July 22), constant red LED appeared, 3rd day (July 23), red LED disappeared. I then prepared my flashtool for flashing the JB firmware .211 KERNEL ONLY. So I plugged in my phone with volume down pressed, I pressed it for 15mins! My finger was f*cked, after 15mins... nothing happened, RED LED just disappeared and I just heard the Windows USB sound. Flash process didn't start, phone didn't give me a GREEN LED. I tried it again and again and miserably same thing happens, can't go to flash mode. Tried the same with volume up button for fastboot mode but still nothing happens, the RED LED just disappears!
Should I just leave my phone charging on the wall socket even if the RED LED disappeared? To get green LED?
SOMEBODY PLEASE HELP ME! I NEED MY PHONE SO BAD! :crying:
i was installing the prerooted/deodexed stock lt28h rom through cwm in the middle of instalation my phone rebooted and came into a sony bootloop i forced it shutdown by pressing power and volume up now its not starting not even charginig what to do please help :crying::crying:
Flash Tool
Be calm and sit back now put your phone to charger for whole night and then next day download flashtool and a firmware for you device and fladh it your device will breath again.......
tejasvi1 said:
i was installing the prerooted/deodexed stock lt28h rom through cwm in the middle of instalation my phone rebooted and came into a sony bootloop i forced it shutdown by pressing power and volume up now its not starting not even charginig what to do please help :crying::crying:
Click to expand...
Click to collapse
we have desame problem my phone is not charging no ligths/led and cant power on after pressing power and up because im stuck in boothllop after afgrading via OTA.
theprint said:
we have desame problem my phone is not charging no ligths/led and cant power on after pressing power and up because im stuck in boothllop after afgrading via OTA.
Click to expand...
Click to collapse
thks for sharing but i have alraedy solved my hard brick problem my phone is back and running normally

[Q] Blank screen, constant reboots, etc

Alright so I'm guessing i might have a broken flex cable, i don't know because of what is happening.
Don't even know where a good place to buy one.
But; first off, I don't use the phone anymore, it just its on my desk, sometimes I touch it, sometimes I don't.
When I was first getting the blank screen issue, the phone just had been sitting on my desk with the screen on (stay awake), several days later, the screen would be off and refused to come on.
Back then I was using a JB rom. Which I was told JB kernels had problems.
I can boot into fastboot and flash a new kernel and it doesn't change anything.
But now if I load up Flashtool, and boot the phone into flashmode, it will reset itself while flashtool is trying to read from it, then boot itself back into flashmode, then a few seconds later reboot itself again.
Last time I got the phone's display to come on, it was because I was able to use flashmode to flash to it before it rebooted itself.
If I try to boot the device, it will display a white LED for several seconds, then flash a few colors before going back to white and the phone resetting again.
Are these all symptoms of a broken flex cable? It makes no sense to me why fastboot mode is fine, but everything else constantly reboots.
I've tried different kernels and roms to make sure there wasn't a problem in that area.
Ellises said:
Alright so I'm guessing i might have a broken flex cable, i don't know because of what is happening.
Don't even know where a good place to buy one.
But; first off, I don't use the phone anymore, it just its on my desk, sometimes I touch it, sometimes I don't.
When I was first getting the blank screen issue, the phone just had been sitting on my desk with the screen on (stay awake), several days later, the screen would be off and refused to come on.
Back then I was using a JB rom. Which I was told JB kernels had problems.
I can boot into fastboot and flash a new kernel and it doesn't change anything.
But now if I load up Flashtool, and boot the phone into flashmode, it will reset itself while flashtool is trying to read from it, then boot itself back into flashmode, then a few seconds later reboot itself again.
Last time I got the phone's display to come on, it was because I was able to use flashmode to flash to it before it rebooted itself.
If I try to boot the device, it will display a white LED for several seconds, then flash a few colors before going back to white and the phone resetting again.
Are these all symptoms of a broken flex cable? It makes no sense to me why fastboot mode is fine, but everything else constantly reboots.
I've tried different kernels and roms to make sure there wasn't a problem in that area.
Click to expand...
Click to collapse
had that problem too. you have to enter CWM and flash any room that you can

[Q] Carbon ROM + lightning kernel kill my phone

I have installed this ROM (CARBON-KK-UNOFFICIAL_odin_build35.zip) then I installed lightning kernel stock .283 Version 5. The phone work fine for many hours, but it overheat, and the battery drain too fast. I put it to charge, I turned on my phone, so far so good, I made I video call and the phone overheat too much and turned off by itself. Now when I try to turned on it, the phone turned off automatic, I can connect it in Fastboot and Flashmode, I could install the stock ROM via flashtool, but the phone turn off after show the logo. I can flash a recovery and I can get in, and re-flash other roms but after the logo the phone turned off. What can I do? put it on the trash? :crying:
melquisedec said:
I have installed this ROM (CARBON-KK-UNOFFICIAL_odin_build35.zip) then I installed lightning kernel stock .283 Version 5. The phone work fine for many hours, but it overheat, and the battery drain too fast. I put it to charge, I turned on my phone, so far so good, I made I video call and the phone overheat too much and turned off by itself. Now when I try to turned on it, the phone turned off automatic, I can connect it in Fastboot and Flashmode, I could install the stock ROM via flashtool, but the phone turn off after show the logo. I can flash a recovery and I can get in, and re-flash other roms but after the logo the phone turned off. What can I do? put it on the trash? :crying:
Click to expand...
Click to collapse
help someone the same thing happened with me was using the beta4 paranoid and did the flash of lightning to cm11 kernel and now my zl only works plugged into the charger .
already tried going to stock by flashtools have not solved the unlocked bootloader
someone help please
did anyone find a solution ??
thnx
Very interesting. I had also Carbon ROM and then installed lightning kernel and had the same issues as you mentioned. Phone reboots suddenly when using too much processor power for example navigation.
Then I was only able to use the phone when it was plugged in the charger. I thought it has nothing to do with the lightning kernel because many others have also the same problem:
http://forum.xda-developers.com/xperia-zl/general/phone-starts-connected-to-charger-t2864009
or
http://forum.xda-developers.com/showthread.php?t=2534327
And now you say it happened after flashing the lightning kernel, its weird.
Mine is being repaired right now. I managed to lock bootloader back and restore original firmware.
Hope it gets the defect parts replaced.
the problem where phone will only run while plugged into charger, seems almost certainly due to heat.
lightning kernel, when installed is set at overclocked values for cpu/gpu, which naturally will generate more heat.
5-10 minutes after installing lightning kernel, my phone will start randomly rebooting on its own even if i am doing nothing at all with it. also feels extremely warm to the touch.
so the first thing i do after installing lightning kernel is lower the cpu/gpu values to thier default settings. problem solved. i do not use the kernel for overclocking....only need it for the DT2W/S2W features, and a few other tweaks. works perfectly fine for my needs. :good:
keeping fingers crossed that i do not run into this issue :fingers-crossed:
Your battery is dead!
Replace it and works fine!!
Also happened to me.

Categories

Resources