For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
*Note* If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone. The Stock ROM contains the Bootloader which should never be downgraded. Fyi: the Bootloader is not the Baseband, the Baseband is just what Modem you're using.
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
bullet2binary said:
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
spongdangly said:
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
Click to expand...
Click to collapse
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
bullet2binary said:
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
exodus454 said:
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
Click to expand...
Click to collapse
I'm glad to hear that this seems to be the proper fix. That's odd that you were having trouble with 4.2 ROMs, but then again I'd been running 4.2 ROMs on my phone since they first started rolling out. It's kind of annoying that everyone's S3 seems to be slightly different then the next.
Yeah this was a weird one all right. Just glad this post had a solution
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
glad i found this otherwise my first noob post would have truly been a noob move. Thanks wouldn't have guessed that fix for a few days at least.
verified it works. but it did require some weird time dealing with a bootloop issue on stock recoveries. had to find a .tar version of CWM to flash via odin for the final result.
Still Stuck at Splash Screen after trying to upgrade to 4.3
Background:
I had been running task's rom since 4.1.x. Upgraded to 4.2 with not problems and I kept the rom current. Tried to upgrade to 4.3 and that is where the problems started. It appeared to work, saw that Google was updating a number of apps but then then I kept getting error messages regarding various about various processes stopping unexpectedly. Rebooted the phone and it came up with Task's kernel splash screen where it remains frozen.
I can get into TWRP (v2.3.3.1) recovery and into Download mode.
I have tried wiping Cache and Dalvik Cache
I have wiped System
I have done a Factory Reset
I have Formatted Data
I have used Odin twice to get back to stock (I747UCDLK3) and both times it says "passed."
When I try to reboot it, however, it comes back to Task's Kernel splash screen (I do not see the Samsung screen)
Any help or suggestions would be great.
UPDATED: Found an older update from April and was able to restore it. Still wondering why 4.3 wouldn't take.
This Works
I was skeptical, but this actually works! Now running Task's 4.3 on my bell i747m without any problems!
Thanks for the tip OP :good:
spongdangly said:
For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
I hope I posted this in the right section but apologies if it's not.
Click to expand...
Click to collapse
If this works you're a life saver! I've been posting around 4.3 threads about this for weeks and no one came up with a decent answer....
Tried reflashing stock with root but didn't work... i'll try your way, see if that works
Gonna try this tonight!!!
Thanks!
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Solved
Thanks, also works for i727 skyrocket
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Kastro1784 said:
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Click to expand...
Click to collapse
spongdangly said:
1. Use Odin to flash the latest stock ROM
Click to expand...
Click to collapse
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
spongdangly said:
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
Click to expand...
Click to collapse
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Kastro1784 said:
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Click to expand...
Click to collapse
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
spongdangly said:
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
Click to expand...
Click to collapse
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
shortydoggg said:
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
Click to expand...
Click to collapse
I'm sorry that I'm unable to help. As I had mentioned I have a Canadian Rogers phone (since I'm in Canada) so I don't know what's going on with the AT&T Stock 4.3 ROMs other then the fact that lots of people are having problems.
If you never flashed or did an OTA update to 4.3 then I'd suggest flashing the Stock 4.1.2 ROM. That or try what Ozark_8125 did since it saves you a couple steps (just make sure that LK3 isn't an older ROM than the one you were on).
If you're unsure what bootloader is currently on your phone and your phone is rooted I'd highly recommend downloading one of the many Root Check apps from the Play Store to verify which bootloader you're currently on.
*Note* I don't know which bootloader is for the 4.1.2 AT&T ROM nor do I know which bootloader came with the 4.3 ROMs. I'm sure a simple search would answer that for you.
Ozark_8125 said:
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Click to expand...
Click to collapse
Samsung fixed my phone free thanks for the help
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Hey guys ... I had a new GS3 from Samsung, so it had 4.3. I flashed a 4.1 stock ROM via Odin, but now when I turn on the phone, I get constant messages about various android processes failing and needing to be stopped. I have since tried another stock ROM and the same thing is happening. Does anyone have any idea what I should do? Maybe flash the latest stock ROM to go back to 4.3? I was trying to revert so I could root and flash a custom ROM but I can't do anything on this right now. I can get back into Download mode though. Please explain things as best as possible as, as you can tell, I clearly don't understand this.
I managed to use the root toolkit to install TWRP, but no custom roms I flash get past the boot screen. So I can get into TWRP and I can get into download mode. I have Odin and I'm not sure where to go from here.
I rooted my phone then used CWM RomManager to make a backup image of the rooted stock rom. Then put KitKat on the phone. Since then I have restored the Rooted stock Rom. Now every time the phone boots I get the Upgrading Android message and the phone is kind of buggy. I am having trouble finding instructions anywhere on how to get it back to complete stock. If someone could point me in the right direction I would appreciate it.
Thanks
What stock AT&T rom were you running when you created the backup?
Oh I guess I should have mentioned that huh.. it was 4.3
Have you tried flashing the 4.3 update.zip file you can find in the developers forum here: http://forum.xda-developers.com/showthread.php?t=2387423.
I feel like you ought to be able to copy the 4.3 zip file to your SD Card and flash via recovery and it should work, although I haven't tried it so I can't be sure.
Hi everyone I hope this is not a repetition of some old thread (I tried but couldn't find though).
I was using my note 2 (T889) on stock 4.3 which i previously flashed via odine. A couple of days ago i came by this good looking kitkat based rom ( eZKAT v2.0 ) and went on to try it. the rom flashed flawlessly and after flashing my modem i got the signals as well but the wifi was not working. tried using dr. ketans wifi patch but didnt get the wifi to working. Anyhow, I decided to go back to 4.3 via odine. The odine flashing completed successfully but i got stuck on T-mobiles boot screen for hours.
Is there anything called "you cant go back to 4.3 from 4.4.2"? If yes, then whats the way around? I really need to go back to the stock.
Thanks.
zetrixNoob said:
Hi everyone I hope this is not a repetition of some old thread (I tried but couldn't find though).
I was using my note 2 (T889) on stock 4.3 which i previously flashed via odine. A couple of days ago i came by this good looking kitkat based rom ( eZKAT v2.0 ) and went on to try it. the rom flashed flawlessly and after flashing my modem i got the signals as well but the wifi was not working. tried using dr. ketans wifi patch but didnt get the wifi to working. Anyhow, I decided to go back to 4.3 via odine. The odine flashing completed successfully but i got stuck on T-mobiles boot screen for hours.
Is there anything called "you cant go back to 4.3 from 4.4.2"? If yes, then whats the way around? I really need to go back to the stock.
Thanks.
Click to expand...
Click to collapse
I had this problem on my Note also. Downgrading versions of Android requires a data wipe. You will need to reflash your 4.4 ROM then backup your data if you want. Save your backup to your computer then install the 4.3 image.
Sent from my Nexus 7
EverDawn4 said:
I had this problem on my Note also. Downgrading versions of Android requires a data wipe. You will need to reflash your 4.4 ROM then backup your data if you want. Save your backup to your computer then install the 4.3 image.
Sent from my Nexus 7
Click to expand...
Click to collapse
I already tried that but still the booting stuck on the t-mobile logo. I read somewhere that locked bootloader don't let you downgrade to previous version. Is this true?
In that case. Try finding a 4.3 rom that's close to stock.
Sent from my Nexus 7
The locked bootloader is always in stock firmwares i.e 4.3 for the Note 2 but not in custom roms meaning u can even install Lollipop custom on it & downgrade smoothly, i have done that many times. The problem is 4.3 stock firmware has locked bootloader hence downgrading still keeps u in 4.3 bootloader even if u remove all the KNOX files.
Stuck trying to downgrade from custom 5.1.1 to stock 4.3
Hi, i have a problem like this, upgrade to a custom 5.1.1 and then sell the phone, the new owner wants to have it stock, i try to downgrade to 4.3 but i cant, in odin i set the phone to flash it but seems like it doesn`t recognize the phone and i dont know why, so, i decided to try in recovery mode installing from the sd card but the sistem abort, so, i don`t know what to do, i`ll appreciates any help, sorry for my english, i do my best. (i have root access before upgrated to 5.1.1).
Hello everyone,
I have a TMO Note 3 running Lollipop at this moment, the phone is rooted, but I tried flashing a new ROM and it soft bricked on me. ODIN stopped at the very beginning of flashing and just bricked the phone. Also TWRP was not working either and still not, but I was able to bring the phone back from the semi-dead state it was in. I want to flash it again but now I don't know if I did something wrong (most likely) and I just need some feedback on what to do. I wanna go to a stock rom so i can upgrade to the actual Lollipop Rom from T-mobile but I was also wondering if I can just flash a stock 5.0 rom that runs better than the one I have. Additionally, I just cant get TWRP to stick at all; every time I try to flash it and try to go into recovery, phone goes into boot loop. Here are some screenshots of the current "about phone" section. I am sorry if i am not asking the right questions but I gotta start somewhere. Thanks everyone in advanced!
https://imgur.com/a/dpn3Y
If you can get into download mode, flash the latest stock rom from Sammobile.com.
audit13 said:
If you can get into download mode, flash the latest stock rom from Sammobile.com.
Click to expand...
Click to collapse
look for the samfirm tool, its faster then going through sammobile:good::highfive: