i dont know if it just with me
my hox become very hot when i use it to serf the net or whatsapp and instagram
even when i change the rom ARHD its still the same
my DHD was great and never heat up
any slice use the phone start to boil and yellow spots come out on the screen
need help
mmh5 said:
i dont know if it just with me
my hox become very hot when i use it to serf the net or whatsapp and instagram
even when i change the rom ARHD its still the same
my DHD was great and never heat up
any slice use the phone start to boil and yellow spots come out on the screen
need help
Click to expand...
Click to collapse
i got the same problem, but with some more usage. I still use my DHD and I think its better than this oven.
omg
this problem need to be solved
i can use it like this
my DHD was much more better
if any one see this please help SOS
What rom are you using... what kernel etc..
On maximus with stock kernel I barely get heat...
Based on the VERY DETAILLED information in your comment
I can only recomend you install a CPU FAN and hardwire it to
the battery...
mmh5 said:
i dont know if it just with me
my hox become very hot when i use it to serf the net or whatsapp and instagram
even when i change the rom ARHD its still the same
my DHD was great and never heat up
any slice use the phone start to boil and yellow spots come out on the screen
need help
Click to expand...
Click to collapse
Your comparing a DHD to a One X.... It's a quad core device *facepalm*...
So before you give up and call the One X a terrible phone (like the 500 rants this forum has) . We need much more information about your device.
1. Have you unlocked the bootloader?
2. Are you running a custom rom/kernel?
3. What base are you on?
4. How long have you had this phone? And how long have you had this problem?
Sent from the best HTC One X in the universe...
mmh5 said:
i dont know if it just with me
my hox become very hot when i use it to serf the net or whatsapp and instagram
even when i change the rom ARHD its still the same
my DHD was great and never heat up
any slice use the phone start to boil and yellow spots come out on the screen
need help
Click to expand...
Click to collapse
Tw1tchy said:
Your comparing a DHD to a One X.... It's a quad core device *facepalm*...
So before you give up and call the One X a terrible phone (like the 500 rants this forum has) . We need much more information about your device.
1. Have you unlocked the bootloader?
2. Are you running a custom rom/kernel?
3. What base are you on?
4. How long have you had this phone? And how long have you had this problem?
Sent from the best HTC One X in the universe...
Click to expand...
Click to collapse
Have you actually read his post? The one you are quoting?
1. As he has ARHD, yes he has
2. Yes he did ARHD
3. Lets say ARHD just for the fun
4. Irrelevant?
If the screen becomes yellow due to the heat, I would say this is hw problem as he tested different roms. UV might help, but the device should not become like this.
What I would be interested in, if he is not using it in direct sunlight on a beach with 40 degrees in the shadow. Even though I saw ppl say their devices survived that.
I am now in Egypt myself and even at night. With -125 UV. And the device still gets hot, red/green blinking on charge.
BUT I never got yellow spots coming out of the screen. And just cuz of that I would says something is wrong on hw level there.
P00r said:
What rom are you using... what kernel etc..
On maximus with stock kernel I barely get heat...
Based on the VERY DETAILLED information in your comment
I can only recomend you install a CPU FAN and hardwire it to
the battery...
Click to expand...
Click to collapse
i flashed rom maximus but without the stock kernal and the temp still the same
im goning to try it now with the stock
mmh5 said:
i flashed rom maximus but without the stock kernal and the temp still the same
im goning to try it now with the stock
Click to expand...
Click to collapse
try faux kernel and undervolt it and underclock it using system tuner or setcpu that will solve all your heat issues
I have exactly the same problem. Whenever i use my One X for navigation in the car (using Navigon) the battery drains more than the Kidigi Car Holder can charge. I already checked all advices that there are like:
- Kidigi Car Holder is charging with AC
- disabled 2 Cores
- UV all frequencies by -125mV
- running the phone in airplane mode
- disabling autobrightness
At the moment i´m running ARHD 9.3.2 with Faux 007m Kernel.
Could someone please help?
PAGOT said:
Have you actually read his post? The one you are quoting?
1. As he has ARHD, yes he has
2. Yes he did ARHD
3. Lets say ARHD just for the fun
4. Irrelevant?
If the screen becomes yellow due to the heat, I would say this is hw problem as he tested different roms. UV might help, but the device should not become like this.
What I would be interested in, if he is not using it in direct sunlight on a beach with 40 degrees in the shadow. Even though I saw ppl say their devices survived that.
I am now in Egypt myself and even at night. With -125 UV. And the device still gets hot, red/green blinking on charge.
BUT I never got yellow spots coming out of the screen. And just cuz of that I would says something is wrong on hw level there.
Click to expand...
Click to collapse
PAGOT said:
Have you actually read his post? The one you are quoting?
1. As he has ARHD, yes he has
2. Yes he did ARHD
3. Lets say ARHD just for the fun
4. Irrelevant?
If the screen becomes yellow due to the heat, I would say this is hw problem as he tested different roms. UV might help, but the device should not become like this.
What I would be interested in, if he is not using it in direct sunlight on a beach with 40 degrees in the shadow. Even though I saw ppl say their devices survived that.
I am now in Egypt myself and even at night. With -125 UV. And the device still gets hot, red/green blinking on charge.
BUT I never got yellow spots coming out of the screen. And just cuz of that I would says something is wrong on hw level there.
Click to expand...
Click to collapse
im not expert in these stuff i barely know how to flash a rom
i downloaded some roms and im going to try them
if there any app will help even if the phone performance will decrease i will use it
mmh5 said:
im not expert in these stuff i barely know how to flash a rom
i downloaded some roms and im going to try them
if there any app will help even if the phone performance will decrease i will use it
Click to expand...
Click to collapse
If it's happening on 2 roms other ones won't help you.
For sure not customized sense ones.
You could compare sense vs cyanogenmod.
But still, the CPU is kernel controlled.
And remember always when you download a Rom it takes like a day to settle, syncing set ups and etc. So to test a Rom you need few days.
Just stick to a Rom for now. And try the advices we already gave you. Undervolting with lets say faux kernel etc.
Sent from my HTC One X using Tapatalk 2
vivek_bhoj said:
try faux kernel and undervolt it and underclock it using system tuner or setcpu that will solve all your heat issues
Click to expand...
Click to collapse
im going to flash the faux kernal now
kindly if you can give the values that i must set
OK... So far so good
I flash ARHD and the faux kernel
I also installed system tuner
In system tuner there is many settings & I don't know what to change
Sent from my HTC One X using xda
PAGOT said:
If it's happening on 2 roms other ones won't help you.
For sure not customized sense ones.
You could compare sense vs cyanogenmod.
But still, the CPU is kernel controlled.
And remember always when you download a Rom it takes like a day to settle, syncing set ups and etc. So to test a Rom you need few days.
Just stick to a Rom for now. And try the advices we already gave you. Undervolting with lets say faux kernel etc.
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
What to value I change???
Sent from my HTC One X using xda
Install Hidden settings app from play store and in the newly created Power saver settings in the app drawer, disable "Reduce CPU cores" or something like this,(its the second option on the list, thats for sure )because basically your HOX runs on 1 core with 1 Ghz, but if you turn this power saver setting off, you will have a full 4 core perfomance, as it should be. This has solved me the heating problem a long time ago when i SEARCHED THIS FORUM, which option i gladly reccomend now to you!!!
Sent from my HTC One X using Tapatalk 2
TripleD_HOX said:
Install Hidden settings app from play store and in the newly created Power saver settings in the app drawer, disable "Reduce CPU cores" or something like this,(its the second option on the list, thats for sure )because basically your HOX runs on 1 core with 1 Ghz, but if you turn this power saver setting off, you will have a full 4 core perfomance, as it should be. This has solved me the heating problem a long time ago when i SEARCHED THIS FORUM, which option i gladly reccomend now to you!!!
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
usually when i open instagram or whatsapp it start heating
but now after 3 videos on youtube and texting still 32-34 C
before its reach 44c
im going to test this way tonight and will tell you any updates :fingers-crossed:
thanks a lot
I have this problem too, i have try this app but still overheating....
Sent from my HTC One X using xda premium
with faux kernal and hidden setting my hox doesn't heat up like before
only once heat up when i force close some apps
but still much better the before :good:
i still want the value that i must change in system tuner
also i notice in system tuner the CPU didn't change at all
waiting for the values
try other roms
Before I face the same problem but after I change the ROM to rd miui, I think the heat still natural for me..
My advice try rd miui for ICS or jelly bean and try cm10 from trip droid ROM with new kernel 3.1.10 for jelly bean.
Now I am still try using trip droid ROM..so far so good about the heat..
Best regards
Ronny tri
mmh5 said:
with faux kernal and hidden setting my hox doesn't heat up like before
only once heat up when i force close some apps
but still much better the before :good:
i still want the value that i must change in system tuner
also i notice in system tuner the CPU didn't change at all
waiting for the values
Click to expand...
Click to collapse
Im glad i could help. In system tuner at the voltages tap ONLY 2 Times the "-25mV" icon, and at the cpu, set the governor to interactive. I guarantee your HOX will freeze your hands while you're holdin It
Tapatalk 2-vel küldve az én HTC One X-ről
Related
currently i have setCPU running on my rooted Dinc with several profiles set.........my question is what is the optimum settings for:
Sampling Rate
Up threshold
ignore Nice load
Powersave bias
mine currently are 40000,70,0,0
i'm trying to find a good setting for best battery life b/c i'm constitenly on my phone all day!!!
thanks for any input.....
What kernal r u running? Several recommend no profiles, and oc will run the battery down.
trembly01 said:
currently i have setCPU running on my rooted Dinc with several profiles set.........my question is what is the optimum settings for:
Sampling Rate
Up threshold
ignore Nice load
Powersave bias
mine currently are 40000,70,0,0
i'm trying to find a good setting for best battery life b/c i'm constitenly on my phone all day!!!
thanks for any input.....
Click to expand...
Click to collapse
Sent from my evo Incredible using xda
i'm just running stock kernal, i'm not comfortable enough with the phone yet to changed kernals........i just setting a default profile so the phone would run 384 on the low end and 786 on high end but when i check system panel it shows the cpu still running up to the max, so i don't know whats going on and if there is anything i need to do to fix it.
do you have "set at boot" checked?
g00s3y said:
do you have "set at boot" checked?
Click to expand...
Click to collapse
yea i did, i read somewhere on here that the "perflock" has to be disabled when using a stock kernal and running froyo, any truth to that ??? and a friend of mine has an incredible and he told me that these mods really don't make that much of a difference, now he's a verizon sales rep so he may be telling me that so i don't change my phone too much
trembly01 said:
now he's a verizon sales rep so he may be telling me that so i don't change my phone too much
Click to expand...
Click to collapse
generally speaking there are two types of people who are employees for phone companies:
A) someone who just wants a paycheck
B) geeks like us who like to hack and mod and tinker
A will tell you that hacking will void warranty, blah blah blah....mostly because they don't know much about what stuff is. B will tell you what they know, and admit when they don't know something.
it sounds like your friend is falling into the A category, especially if they're saying "mods don't change much". they change quite a bit, so be careful.
as far as your question in the OP, with my eris i would just mess with stuff, and see how the phone runs. don't save to run at boot until you know it's stable and will not crash or freeze your phone. adjust settings, and see how it responds, repeat as necessary.
trembly01 said:
i'm just running stock kernal, i'm not comfortable enough with the phone yet to changed kernals........i just setting a default profile so the phone would run 384 on the low end and 786 on high end but when i check system panel it shows the cpu still running up to the max, so i don't know whats going on and if there is anything i need to do to fix it.
Click to expand...
Click to collapse
nandroid and flash KK#5. you won't be sorry, its very stable and very quick
MMBosstones86 said:
nandroid and flash KK#5. you won't be sorry, its very stable and very quick
Click to expand...
Click to collapse
where can i get that kernel ??
Yes you have to disable perflock.
I only adjusted my power bias to 650 I think which is 65%. 1000 being 100% and 10 being 1%. All this does is make sure you cpu stays on the lower end of the usage. I have a 2150 and stream pandora a lot and always have 3g running, I go online and everything and I get 2 days of usage with a down clock and some profiles.
Sent from my Incredible using Tapatalk
trembly01 said:
where can i get that kernel ??
Click to expand...
Click to collapse
google or the android development forum, don't have the link on hand
mihneagabriel said:
Yes you have to disable perflock.
I only adjusted my power bias to 650 I think which is 65%. 1000 being 100% and 10 being 1%. All this does is make sure you cpu stays on the lower end of the usage. I have a 2150 and stream pandora a lot and always have 3g running, I go online and everything and I get 2 days of usage with a down clock and some profiles.
Are you running stock HTC sense Rom?
Sent from my Incredible using Tapatalk
Click to expand...
Click to collapse
Sent from my ADR6300 using XDA App
Yes
Sent from my Incredible using Tapatalk
trembly01 said:
where can i get that kernel ??
Click to expand...
Click to collapse
Search works wonders
http://forum.xda-developers.com/showthread.php?t=760050
Hi,
I've had my Archos G9 80 updated to the latest android official 4.0.5 from and since then i'm expriencing lots of crushes and freezes. I'm getting them randomly with no specific app working.
Also, i have tried to do full formats (Android + Data), and still having same issues.
Does anyone have any idea what else i can try?
Thanks.
I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.
DeeDroid said:
I changed the CPU govenor from "hotplug" to "interactive".
Click to expand...
Click to collapse
how this is done? Ι have the same problem!
africa_twin said:
how this is done? Ι have the same problem!
Click to expand...
Click to collapse
Yes, can this be done from the phone itself? Within the ROM?
You can set this in any tool that is intended for overclocking. I don't overclock, I only changed the Govenor.
I use "SetCPU". ("No-frills CPU Control" should do the same.)
So does this have any other effects on the phone?
RichWPX said:
So does this have any other effects on the phone?
Click to expand...
Click to collapse
Nothing too serious. Your CPU is clocked dynamically so it doesn't run full speed when there is nothing to compute(save energy). To my understanding the govenor is basically a policy to manage how quickly the frequency steps up/down on changing CPU load. So "powersave" is supposed to save energy but make the system a little less reactive than "interactive" Governor for example. I think I read somewhere "hotplug" deactivates the second core on low load situations, I suspect for some strange reason my device might have crashed sometimes on trying to wake up the sleeping second core. Well maybe I'm wrong, that's why I'm interested if it helps others.
I didn't notice any change in battery lifetime, mostly it's the display anyway that drains the battery. Everything is running well, battery lifetime is great too and no crash/freeze at all since i changed that setting and it crashed almost every damn day before, no matter if it was Honeycomb or ICS.
I downgraded the device to 4.0.4 and since then, no crushes.. I guess for some reason 4.0.5 isn't stable on my device.. ill stick with this version unroll they get another one out..
To downgrade, just install official update file of the version you want to upgrade to..
DeeDroid said:
Nothing too serious. Your CPU is clocked dynamically so it doesn't run full speed when there is nothing to compute(save energy). To my understanding the govenor is basically a policy to manage how quickly the frequency steps up/down on changing CPU load. So "powersave" is supposed to save energy but make the system a little less reactive than "interactive" Governor for example. I think I read somewhere "hotplug" deactivates the second core on low load situations, I suspect for some strange reason my device might have crashed sometimes on trying to wake up the sleeping second core. Well maybe I'm wrong, that's why I'm interested if it helps others.
I didn't notice any change in battery lifetime, mostly it's the display anyway that drains the battery. Everything is running well, battery lifetime is great too and no crash/freeze at all since i changed that setting and it crashed almost every damn day before, no matter if it was Honeycomb or ICS.
Click to expand...
Click to collapse
Thanks! And I have notices ICS is not as snappy as GB was... I mean GB flew! Swiping the screen, it feels a little off now.
RichWPX said:
Thanks! And I have notices ICS is not as snappy as GB was... I mean GB flew! Swiping the screen, it feels a little off now.
Click to expand...
Click to collapse
GB? Gingerbread? Guess you mean Honeycomb. Anyway, I experienced ICS to be much better.
DeeDroid said:
I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.
Click to expand...
Click to collapse
changing govenor from "hotplug" to "interactive" seems to help against random freezes. 4 days without problems until now i had freezes with ics, but never with honeycomb.
device: archos 101g9
[ROM] Archos ICS - Firmware 4.0.5(4.0.3) - ROOT & BUSYBOX , Only for SDE (thanks surdu_petru)
DeeDroid said:
I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.
Click to expand...
Click to collapse
That seems to be my problem too. Setcpu requires root. is there a very easy way to do this, just to run this setcpu? There used to be a z4 tool, but can't seem to find it anymore.
Edit I see that I need superoneclick. Will temporary root suffice or will I need permanent root to change the governor setting.and keep it so.
Unfortunately all know temp root variants tend to brake things- im Honeycomb sound, in ICS 3d driver.
The only real option is to enable SDE and use custom firmware.
As for freezes- try reinstalling apps. Direct upgrade from Honeycomb does not work for all
tapatalked from Xperia Arc S
DeeDroid said:
GB? Gingerbread? Guess you mean Honeycomb. Anyway, I experienced ICS to be much better.
Click to expand...
Click to collapse
I have the same experience. Hc was laggy and slow. Ics is much faster and smoother.
Sent from my ARCHOS 80G9 using Tapatalk
gen_scheisskopf said:
Unfortunately all know temp root variants tend to brake things- im Honeycomb sound, in ICS 3d driver.
The only real option is to enable SDE and use custom firmware.
As for freezes- try reinstalling apps. Direct upgrade from Honeycomb does not work for all
tapatalked from Xperia Arc S
Click to expand...
Click to collapse
sorry for the n00b question, but SDE stands for ??? S ? Develeper Edition ?
Will "Superoneclick" not root my device ?
sbtwister said:
sorry for the n00b question, but SDE stands for ??? S ? Develeper Edition ?
Click to expand...
Click to collapse
Special Developer Edition
sbtwister said:
Will "Superoneclick" not root my device ?
Click to expand...
Click to collapse
No, it won't. Gen9 system layout is different than for most other devices
hey, back to topic
5 days without freeze with govenor "interactive". i witched back to "hot plug" this morning and had to reboot my tablet 2 times today. for my case, "interactice" seems to help against random freezes.
mines performance intstead of interactive... experienced some freezing n interactive..
Man I'm really pissed.
Yesterday I had to hard reboot 7 times
Sent from my X8 using xda premium
hmm,
sounds not good. archos stands not for high quality i guess. we get what we pay . i had an archos 101g8, now a 101g9 and trouble with hard-/firmwares since 2010. i think, this was the last one - no furthermore advantures
@IrishStuff09: you did reformat for ics or upgrade from honeycomb? the best way is to start from scratch and skip upgrades.
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
I do not experience this issue. When you flashed the rom, did you do a clean install? Have you formatting the device?
Yup.. I format everything.. I use the touch recovery and just use every option that it provides and wipe everything.. It even does it when there is nothing installed. I usually delete almost all the useless system apps that I don't use like the google music app and all of the ones civato provides... I even change the animation settings to .5 in the developer section.. should I turn them off all together?
Crimson Ghoul said:
Yup.. I format everything.. I use the touch recovery and just use every option that it provides and wipe everything.. It even does it when there is nothing installed. I usually delete almost all the useless system apps that I don't use like the google music app and all of the ones civato provides... I even change the animation settings to .5 in the developer section.. should I turn them off all together?
Click to expand...
Click to collapse
The animations should not have anything to do with it. Does this only occur on that rom? Have you tried other roms and experienced that issue?
not many other roms out there.. I have used stock and his.. had the same issue on both.. Also happens on my brother's a500.. it usually happens when unlocking and going into any app.. it sits there for a few seconds and then opens whatever it is i opened
Crimson Ghoul said:
not many other roms out there.. I have used stock and his.. had the same issue on both.. Also happens on my brother's a500.. it usually happens when unlocking and going into any app.. it sits there for a few seconds and then opens whatever it is i opened
Click to expand...
Click to collapse
This is starting to sound like a hardware issue. Before that is concluded, you could:
- Make sure the governor is not set to "conservative"
- Try a clean install of CM9
If the problem still arises, its most likely a hardware issue.
I'm using the OC kernel and have it to 1500.. I also always leave it on performance.. I figure it would kill my battery life but I don't use it much.. and i tried cm9 also.. too many issues as of right now
Crimson Ghoul said:
I'm using the OC kernel and have it to 1500.. I also always leave it on performance.. I figure it would kill my battery life but I don't use it much.. and i tried cm9 also.. too many issues as of right now
Click to expand...
Click to collapse
It doesn't seem it can be anything else but a hardware issue in that case.
NB. Overclocking to a high frequency can cause instability and bring about that issue (but since you experienced it on the stock rom, its quite likely not to be that).
the overclocking helps to speed it up a tad bit.. for the most part it just lags.. i did a clean install just now
Thought I would jump in. Stock ics would slow down and lag on me, jittery transitions poor performance in games or movies, but it took an hour not a few minutes. However testing the T20 kernel before the release kernel had that exact issue, bogging and lagging within minutes.
His release kernel doesnt do it, and flex extreme as well as my cm9 builds don't, even with T20 kernel. Consider flashing that kernel to see what happens.
Side note...what issues did you have with cm9? And what release? My build 1 has been running for 3 days no reboots stable as can be undervolted and OC when needed. Something to maybe think to try to see if it persists. T20 kernel works fine with it too.
Tapatalked from my Galaxy S II.
Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
Yup, EVERYTIME I turned on my screen then unlocked it to laggggggg for a lil while. I'm now using CM9 n that issues gone. Try CM9
forum.xda-developers.com/showthread.php?t=1705554
A100 Running CM9 Nightly ROM n ezT20 OC Kernel :-D
To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.
eww245 said:
To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.
Click to expand...
Click to collapse
That reminds me...setting a screen off profile with the same min/Max speed can cause issues with that, give Max a notch or two higher. And don't have it change the governor leave it the same. So like interactive screen on Myst nit be conservative screen off, doesn't work that way.
Tapatalked from my Galaxy S II.
I had the same issue on stock. I noticed there are 2 weather applications installed (version 1 and version 2) immediately after I disabled the old weather application (version 1) this stopped happening. I used the ICS GUI to do the disable.
This might not be the case in custom rom, but is true for stock. Post reply and let me know if this fixed it for you also.
Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
Do you have a micro SD card plugged in? Try reformatting the card with a computer. Worked for me.
Sent from my A100 using XDA
I felt the need to add my two cents in this....this has been happening to me for the longest with the flex reaper rom ONLY. I've used stock and ZN's rom and those did not lag after unlock...only flex reaper. I'm currently using flex reaper and still experience it from time to time but doesn't destroy my day at all...
Give the CM9 nightly ROM's a go. No Bluetooth n no HDMI audio, but everything else is fine n damn smooth. Those issues will be fixed though
A100 Running CM9 Nightly ROM n ezT20 OC Kernel :-D
eww245 said:
To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.
Click to expand...
Click to collapse
I installed Flex 100 Reaper with stock and it it seemed to run smooth enough. Then I installed the OC kernal, and started to get lag. I was looking around to find the OC settings, but can't see it anywhere in settings..
Can anyone direct me to where can I adjust the governor/max/min CPU settings?
Sorry for the noob question.
htc_softbank said:
I installed Flex 100 Reaper with the OC kernal, and started to get lag. I was looking around to find the OC settings, but can't see it anywhere in settings..
Can anyone direct me to where can I adjust the governor/max/min CPU settings?
Sorry for the noob question.
Click to expand...
Click to collapse
Setcpu from the play store.
The overclock settings are not integrated like CM.
My N2 makes me crazy when it gets warm.
When it reaches about 36 celsius degrees it starts with frequency limit of 800MHz.
The second step is making 2 cores offline and at last my gadget becomes limited to 2 cores at a max. of 500MHz.
It becomes almost unusable for me when in car. I use two navis in multiwindow (Waze and Sygic) and AutoGuard recording in background with FullHD and in about 5 minutes it's restricted hardly.
I know it's for safety reasons but I think it's too strict.
Is there a possibility to raise the thresholds of these by a few degrees?
What kernels support this?
There is a nice app called Android Tuner which is able to set these tresholds but it is for Qualcomm CPU-s only...
Thanks for any answers in advance!
le_vente said:
My N2 makes me crazy when it gets warm.
When it reaches about 36 celsius degrees it starts with frequency limit of 800MHz.
The second step is making 2 cores offline and at last my gadget becomes limited to 2 cores at a max. of 500MHz.
It becomes almost unusable for me when in car. I use two navis in multiwindow (Waze and Sygic) and AutoGuard recording in background with FullHD and in about 5 minutes it's restricted hardly.
I know it's for safety reasons but I think it's too strict.
Is there a possibility to raise the thresholds of these by a few degrees?
What kernels support this?
There is a nice app called Android Tuner which is able to set these tresholds but it is for Qualcomm CPU-s only...
Thanks for any answers in advance!
Click to expand...
Click to collapse
You can change a value in a file under system, but it is not so safe..
Mate996 said:
You can change a value in a file under system, but it is not so safe..
Click to expand...
Click to collapse
Very helpful...
Sent from my GT-N7100 using XDA Premium 4 mobile app
Mate996 said:
You can change a value in a file under system, but it is not so safe..
Click to expand...
Click to collapse
Not exactly understand...
There must be a safe setting for it as with Perseus kernel the thresholds are higher, but not too much. I forgot to edit my question according my experiences with Perseus.
At least with Perseus I get a max of 1000MHz at most cases but it is not enough for me cause I use apps needing high resources.
Would You be so kind to write about the value to be changed in order to get higher thresholds?
If I understand you correctly. Then you could try trickster mod.
Or try saber kernel. I use this baked into the Jedi rom.
Sent from my GT-N7105 using xda app-developers app
3vo3d said:
If I understand you correctly. Then you could try trickster mod.
Or try saber kernel. I use this baked into the Jedi rom.
Sent from my GT-N7105 using xda app-developers app
Click to expand...
Click to collapse
Thank You for the advice!
Now I had some time so I'm on Saber kernel and just testing.
The testing is awesome till now: the phone is working more powerful with this kernel and doesn't get hot so soon. :good:
Oh, now there is something strange, the programs get FC-s...
The phone is on charger, I ran AutoGuard in the background in FullHD, Sygic and Waze in MultiWindow, VideoPlayer in popup with a FullHD video and SuperPlayer in popup with another FullHD video. It was extremely fine but after a few minutes the players collapsed and AutoGuard had an error. The system is stable anyway. It seems I have to restart phone now...
Edit: After restart I got an old problem back: Dropbox is unable to run again... I loved Perseus because of this, on Perseus this problem was away... I hope that I won't get the other issue back with my WiFi... And it seems, AutoGuard became stupid too... :crying:
I don't give up and keep on trying to make them ok.
But I can't find the thermal control feature in Trickster Mod Donation altough I have just a minute for it.
I am reading Trickster webpage to get ahead...
Question: Are You using Jedi ROM and have no thermal problems?
In that case I'm going to try that ROM, cause I'm on hunting for a ROM that works with no problems for me.
I tried some lately and till now Omega v18 was the best amongst them. I tried MIUI, ProBam, Hawkish in the last days and I get problems with all of them or had non-working applications and/or features which ones are essentials for me...
Edit: mmmmmmmm, as see there is no Jedi ROM for international N7100...
hey bro,
wow you seem to be a bit more advanced than me so maybe ive reached the limit of the advice i can give you.
However, if you inform me how to check for thermal problems i will surely do that and then report back.
the saber kernel to the best of my knowledge is underclocked so if you try to o/c it maybe that will prevent your fc's. I have read in the various threads, of which the community is very helpful, of some issues for heavy users due to the u/c.
Regarding the jedi rom i am a uk 7105 user and to the best of my knowledge i thought it would also work for international 7100 users?!?!
Here is the thread i use.
http://forum.xda-developers.com/showthread.php?t=1987634
reading the op of that thread it would appear you are correct. I do know they are working on version 18 so maybe that will work for you. fingers crossed.
3vo3d said:
hey bro,
wow you seem to be a bit more advanced than me so maybe ive reached the limit of the advice i can give you.
However, if you inform me how to check for thermal problems i will surely do that and then report back.
the saber kernel to the best of my knowledge is underclocked so if you try to o/c it maybe that will prevent your fc's. I have read in the various threads, of which the community is very helpful, of some issues for heavy users due to the u/c.
Regarding the jedi rom i am a uk 7105 user and to the best of my knowledge i thought it would also work for international 7100 users?!?!
Here is the thread i use.
http://forum.xda-developers.com/showthread.php?t=1987634
reading the op of that thread it would appear you are correct. I do know they are working on version 18 so maybe that will work for you. fingers crossed.
Click to expand...
Click to collapse
Thank You for Your effort!
I'll keep on investigating for a solution.
Unfortunately the real test was horrible with Saber kernel, when I tested it in car the temperature got high soon and the thersholds were low again.
But it's a good idea to try o/c thank You very much!
I'll try it tomorrow, now I have to go to play Cod4... :laugh:
And I found that TWRP is recommended for Saber and a few minutes untouching after the restart so I'll try again.
Have a nice day!
you too bro, sorry i couldnt help more.
but if you post in the saber kernel thread there are some helpful and intelligent folks in there that may have a better solution for you.
enjoy cod
3vo3d said:
you too bro, sorry i couldnt help more.
but if you post in the saber kernel thread there are some helpful and intelligent folks in there that may have a better solution for you.
enjoy cod
Click to expand...
Click to collapse
Thank You again!
I got some experiences with the newest Saber kernel and I like it 'cause the first kernel I can use 100MHz step with and using 300MHz step too.
It seemes to be good at battery consumption too. My only problem that this kernel doesn't support STweaks so I can't regulate charging voltages like I used to. Perhaps only Perseus kernel makes it possible as I can't get any other programs for it till now. Or NEAK kernel and the new versions of AGNi pureSTOCK kernel as I read their pages. I'll try them some day. But Perseus is my favourite.
I think it's important to say that the kernel isn't UC/OC by default so this doesn't make any problems and it's not UV-ed too.
I set min. to 100MHz and max. to 1920MHz to test and it's stable till now. I tried to Overvolt slightly and had no change on media programs behavior they don't like each other as I see.
Trickster Mod is nice 'cause it shows the CPU temperature which was helpful to understand this regulations of thermal control are needed.
When I tested it turned out that CPU is below 70 degrees while the battery temparuture is 'only' about 40 degrees.
So thanks for Your kind advises!
wow. Ok i think i understood most of your post. probably a little bit over my head but i need to learn.
I really like the new kernel im getting 1% battery drain an hour with the screen off which truly is unheard of for me,
The kernel runs real smooth apart from when i play asphalt 8. Or i should say it runs smooth playing the game until the phone tries to do something else. For example if it attempts to update a programme or if a message/email comes through. then the game just lags and i have to wait for the phone to stop multi tasking before the car starts to move normally again.
So im surprised to read you say the kernel isn't uc/uv by default??? I was pretty positive it was. But i dont know for sure and im probably not clever enough to figure it out lol.
I wonder what settings i would need to increase to aid the phone in its multi tasking? Also there must be some kind of programme we could use that would test our specific phone/cpu and tell us which settings it would prefer. As i believe each phone will run slightly different?
You are right i remember reading the kernel does not work with stweaks.
I wish i could work with you and figure out how to optimise our settings but i simply dont have the skill set.
I presume you used trickster to overvolt slightly?
3vo3d said:
wow. Ok i think i understood most of your post. probably a little bit over my head but i need to learn.
I really like the new kernel im getting 1% battery drain an hour with the screen off which truly is unheard of for me,
The kernel runs real smooth apart from when i play asphalt 8. Or i should say it runs smooth playing the game until the phone tries to do something else. For example if it attempts to update a programme or if a message/email comes through. then the game just lags and i have to wait for the phone to stop multi tasking before the car starts to move normally again.
So im surprised to read you say the kernel isn't uc/uv by default??? I was pretty positive it was. But i dont know for sure and im probably not clever enough to figure it out lol.
I wonder what settings i would need to increase to aid the phone in its multi tasking? Also there must be some kind of programme we could use that would test our specific phone/cpu and tell us which settings it would prefer. As i believe each phone will run slightly different?
You are right i remember reading the kernel does not work with stweaks.
I wish i could work with you and figure out how to optimise our settings but i simply dont have the skill set.
I presume you used trickster to overvolt slightly?
Click to expand...
Click to collapse
No, I didn't overvolt at last. But once I tried and didn't helped on my problems.
Unfortunately now I'm back on Perseus kernel again 'cause some issues with Saber. It became crazy every time and locked my CPU on 160MHz only and only reboot helped.
The other issue was the stuck system server process what was active all night and didn't stop hard work.
Now I'm on reading the kernel's page till I get cleverer on it... then I perhaps try it again 'cause I liked it.
http://forum.xda-developers.com/showthread.php?t=2260397&page=5
Hey, i have this problem from the begining...
So i have android version 4.2.2.
I'm running phone on franco Kernel 3.0.85 with Paranoidandroid Rom 3.56, Also i use app to OC my phone to 1,6ghz.
So everything is okay expect gaming , example when i play temple run 2 and i set on the best quality it will not run smooth you can see lags ingame and i think this phone should run it easily.
I was reading forum but i didn't found any solution for my problem, i tried to find busfreq_static with following informations :
/sys/devices/system/cpu/cpu0/cpufreq/busfreq_static
but there's no busfreq_static file when i enter to cpufreq directory , i use File Explorer just to check am i able to find busfreq_static file but i can't.
Any solution , any help would be much appreciated.
Thanks
Maybe buy a N4 or HTC One!!!
Sent from my Galaxy Nexus using xda app-developers app
wisefreakz said:
Maybe buy a N4 or HTC One!!!
Sent from my Galaxy Nexus using xda app-developers app
Click to expand...
Click to collapse
Add the Gs4 as well
wizox said:
Hey, i have this problem from the begining...
So i have android version 4.2.2.
I'm running phone on franco Kernel 3.0.85 with Paranoidandroid Rom 3.56, Also i use app to OC my phone to 1,6ghz.
So everything is okay expect gaming , example when i play temple run 2 and i set on the best quality it will not run smooth you can see lags ingame and i think this phone should run it easily.
I was reading forum but i didn't found any solution for my problem, i tried to find busfreq_static with following informations :
/sys/devices/system/cpu/cpu0/cpufreq/busfreq_static
but there's no busfreq_static file when i enter to cpufreq directory , i use File Explorer just to check am i able to find busfreq_static file but i can't.
Any solution , any help would be much appreciated.
Thanks
Click to expand...
Click to collapse
I already know you OC, but you overclock controlling voltages yourself, or rather you rely on SR to do it for you?
wisefreakz said:
Maybe buy a N4 or HTC One!!!
Sent from my Galaxy Nexus using xda app-developers app
Click to expand...
Click to collapse
Seraz007 said:
Add the Gs4 as well
Click to expand...
Click to collapse
While it may be funny, this helps nothing to the thread. Please don't offtopic. TIA.
wizox said:
Hey, i have this problem from the begining...
So i have android version 4.2.2.
I'm running phone on franco Kernel 3.0.85 with Paranoidandroid Rom 3.56, Also i use app to OC my phone to 1,6ghz.
So everything is okay expect gaming , example when i play temple run 2 and i set on the best quality it will not run smooth you can see lags ingame and i think this phone should run it easily.
I was reading forum but i didn't found any solution for my problem, i tried to find busfreq_static with following informations :
/sys/devices/system/cpu/cpu0/cpufreq/busfreq_static
but there's no busfreq_static file when i enter to cpufreq directory , i use File Explorer just to check am i able to find busfreq_static file but i can't.
Any solution , any help would be much appreciated.
Thanks
Click to expand...
Click to collapse
first, dont OC to 1.6!! the following may help you:
go to Settings and click on Developer Options and enable Force 4x MSAA. Multisample anti-aliasing (MSAA) is a technique used to improve image quality. Since the Gnex has a GPU capable of supporting MSAA. Keep in mind this will also cause your GPU to work harder and your device may get hotter and consume more power than normal. It’s also possible that all games may not support this.
beekay201 said:
I already know you OC, but you overclock controlling voltages yourself, or rather you rely on SR to do it for you?
While it may be funny, this helps nothing to the thread. Please don't offtopic. TIA.
Click to expand...
Click to collapse
I'ts not problem about OC , even if i set to 1,2ghz there are no changes , i just dont know what could be the problem , cuz the game runs smooth on other phone which is not good as this one , thats weird , im not controlling voltages , i didn't touch anything.
samersh72 said:
first, dont OC to 1.6!! the following may help you:
go to Settings and click on Developer Options and enable Force 4x MSAA. Multisample anti-aliasing (MSAA) is a technique used to improve image quality. Since the Gnex has a GPU capable of supporting MSAA. Keep in mind this will also cause your GPU to work harder and your device may get hotter and consume more power than normal. It’s also possible that all games may not support this.
Click to expand...
Click to collapse
No , it didnt help. I already tried it before , but when i Force 4x MSAA it just makes game more lagy , maybe cuz of game , anyway i gave an example Temple Run 2 , but even other 3D games are laging , why shouldnt I OC to 1.6 , could brick phone or ?
It can blow up your cat. If it's the same with 1.2GHz... Why are you OC'ing? Go do some reading on voltage control and smartreflex on 4460.
Something tells me you're forgetting basics on how to OC on this device. If you don't supply enough voltage for all the cpu steps, device will stutter and lag, might even reboot.
a maguro wrote this.
beekay201 said:
It can blow up your cat. If it's the same with 1.2GHz... Why are you OC'ing? Go do some reading on voltage control and smartreflex on 4460.
Something tells me you're forgetting basics on how to OC on this device. If you don't supply enough voltage for all the cpu steps, device will stutter and lag, might even reboot.
a maguro wrote this.
Click to expand...
Click to collapse
Well i guess i need to put higher voltage when i am OC-ing , and how much voltage should i use for 1,2ghz , default ? Or incrase to higher voltage value ? Tell me something more about it , cuz im not well informed
wizox said:
Well i guess i need to put higher voltage when i am OC-ing , and how much voltage should i use for 1,2ghz , default ? Or incrase to higher voltage value ? Tell me something more about it , cuz im not well informed
Click to expand...
Click to collapse
first thing you need to do is disable SmartReflex® across the board, so that your user-defined voltages stick.
messing with voltages is very device-specific. increment voltage by small ammounts, stress-test and use the device for a while to make sure it's stable.
have you tried running those games while running Google's stock kernel?
beekay201 said:
first thing you need to do is disable SmartReflex® across the board, so that your user-defined voltages stick.
messing with voltages is very device-specific. increment voltage by small ammounts, stress-test and use the device for a while to make sure it's stable.
have you tried running those games while running Google's stock kernel?
Click to expand...
Click to collapse
I guess that stock kernel is : JOP40C kernel ? Am i right , i didnt try that kernel , you suggest me to flash this JOP40C kernel and to try if something will be fixed ?
wizox said:
I guess that stock kernel is : JOP40C kernel ? Am i right , i didnt try that kernel , you suggest me to flash this JOP40C kernel and to try if something will be fixed ?
Click to expand...
Click to collapse
Well when i flashed this kernel , and rebooted phone it just wont pass google logo , so i decided to flash again franco kernel to get my phone to work , dont know what's the problem with flashing stock room
wizox said:
Well when i flashed this kernel , and rebooted phone it just wont pass google logo , so i decided to flash again franco kernel to get my phone to work , dont know what's the problem with flashing stock room
Click to expand...
Click to collapse
Do you even know anything about ROMs and kernels?
When I said have you tested this on stock kernel, I meant, did you try this on stock ROM, but specified kernel because, it's like, common knowledge for someone who flashes ROMs, that custom ROMs devs often alter kernel (and ramdisk) to support features on their custom roms..
Have you for example tried reflashing PA, and just PA, nothing else? Does it lag then?
Have you for example tried fully reverting back to stock? (factory images)
Why is it that you just want your games not to lag, not even trying to gain a deeper understanding about what people are telling you.
Listen, this is the last time I'm saying this:
I told you to check your voltages, since you're OC'ing, and expecting SR to do the job for you.
Test by reflashing again PA, with no custom kernel.
Test by going back to stock, through fastboot/factory images.
Temple Run 2 on best quality lags in mine too.Probably it was designed for 1080p.Just keep the graphics a little lower, doesn't affect gameplay or quality
Sent from my maguro