Develop Bugs

How to Replace your Scratched Galaxy S2 Screen DIY

I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!

thanks for the write up, do you have any more photos of your process?

OMG, it's like watching an autopsy.

Could a better resolution screen or even 3d screen be used/upgraded later on?

Nice to know for something happens, Hope not

Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.

Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.

On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App

wow that is the definition of T H I N !!!!!

Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site

psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.

I wonder how these replacement parts compare to the quality of the original parts.

Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?

psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.

It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.

BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL

Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB

DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.

I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance

buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB

Shattered Glass

Well, today was a say day for me, for I dropped my HOX on some concrete and shattered the glass, phone still works and lcd isn't damaged... but I was wondering if theres anyone here who knows a decent repair centers in the UK, i've seen this http://compare.ebay.co.uk/like/2511...ixedPriceItemTypes&var=sbar&adtype=pla&crdt=0 and i'm pretty sure thats all I need... I could even try myself

Perhsps HTC can sell us an original part, we could also ask for s one x+ battery. I don't know how much the one x digitisee and glass replacement would cost. The whole svren inc LCD is 160 IIRC so probably less than 100?
I also.have a damaged screen. My concern is whether the. Parts are really originals as claimed, be cause I'd like a real gorilla glass panel. Also, how do I reconnect the connectors I have to unplug to get the screen . Presumably it's obvious otherwise it would have been mentioned in repair guides.
HTC may repair and sell originals, how much for I don't know.
My LCD appears fine usually, but sometimes there is a yellow tint to some of the screen, presumably related to epoxy glue. Also I was pressing down on the Screen and now one of the cracks appear slightly blue Around the edges, not sure if this will change if I replace.
Finally I saw a story on xdA I think of a guy who Bricked his while trying to replace the screen.

CraigUK87 said:
Well, today was a say day for me, for I dropped my HOX on some concrete and shattered the glass, phone still works and lcd isn't damaged... but I was wondering if theres anyone here who knows a decent repair centers in the UK, i've seen this http://compare.ebay.co.uk/like/2511...ixedPriceItemTypes&var=sbar&adtype=pla&crdt=0 and i'm pretty sure thats all I need... I could even try myself
Click to expand...
Click to collapse
From what I have seen in One X screen replacement videos and read in this and other forums the digitizer is not easily separable from the LCD. So most probably you'll have to replace the whole display assembly (i.e digitizer + LCD screen).

Nope
None of the replacement parts in this thread so far are close to genuine, and will be cheap crap.
http://www.ebay.co.uk/itm/320929331645?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
This is what a genuine replacement looks like, and costs. If it's under £100, forget it; it's crap. If it comes as separate parts, it's crap. The One X screen is bonded at the factory across the entire area of the screen - you will never get a good screen if you assemble it yourself, or even if a repair centre does it. You'll get an air gap between the LCD and digitizer, and therefore it will look awful in daylight.

Dave Trouser said:
None of the replacement parts in this thread so far are close to genuine, and will be cheap crap.
http://www.ebay.co.uk/itm/320929331645?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
This is what a genuine replacement looks like, and costs. If it's under £100, forget it; it's crap. If it comes as separate parts, it's crap. The One X screen is bonded at the factory across the entire area of the screen - you will never get a good screen if you assemble it yourself, or even if a repair centre does it. You'll get an air gap between the LCD and digitizer, and therefore it will look awful in daylight.
Click to expand...
Click to collapse
What about this? http://www.ebay.co.uk/itm/REPLACEME...A%2BFICS%2BUFI&otn=21&pmod=251138091338&ps=54

BUMP
So is there anyone here can lend me a hand... I'm from the UK and i need to get my LCD replaced... does anyone know of any legit repair centers... Please.. i'm pretty desperate now

CraigUK87 said:
So is there anyone here can lend me a hand... I'm from the UK and i need to get my LCD replaced... does anyone know of any legit repair centers... Please.. i'm pretty desperate now
Click to expand...
Click to collapse
Call up HTC. I've done some research, seems to agree with what is posted above.

I feel your pain.. I have a small crack on the side of my S3 screen. How bad is it? If its smalland on the side check out an overlay Luke by Spectre. They are about 4mm thick and are cut to cover the whole face of the screen
Sent from my EndeavorU using Xparent ICS Tapatalk 2

Replacing just the glass

I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2

May i ask how you replaced the glass, and where you bought it? Shattered mine couple of days ago...

Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
My English is not my native language, but considering the word adhesive, you must referring to the double side tape part that holds the digitizer and the glass together.
Assuming that, from my own experience it is a no-go. If you are experiencing sticking parts (ie. it's not properly glued) I am afraid you might have to replace the whole adhesive.
I had the same issue on my Desire HD and about 1 month after replacement, same as you kept pushing it to take the haze away, the inevitable happened. A tiny opening not being able to see with the naked eye, left enough room for dust to enter under the glass. One month later, there was so much dust in it that I had to buy a new full screen.
However, months later, I tried some old trick for future experiments You can eventually take a paint dryer, and try to heat up the lose part then applying some light pressure onit. This process should make the glue on the adhesive very soft and with a bit of luck it might stick on the glass.
I'd say perhaps 60-70 degrees. Don't worry, even 100 degrees won't break your screen unless u're heating it up for more than 10 minutes or so
GL

Fantastic, I'll give heat a try to get it to stick. Unfortunately I can't find the double sided tape anywhere otherwise I'd replace it. I'm in Australia so shipping is pretty expensive from most places outside of the country. I really appreciate the reply
I bought the glass alone off eBay, I believe it was around $30. To replace it took a lot of patience, a hairdryer on low for 15 mins to heat the glue up, finding a spot to slowly pry the glass away from the LCD. As I said, a lot of patience and a lot of mess since my screen was badly cracked and kept breaking off. Was worth it to save $300 though. Figured I could do it for $30 myself and if it broke I'd have had to of paid for both either way
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2

It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order

matzone said:
It seems you already build enough experience with heating up the device. I hope it does the trick for you. On the other hand the adhesive itself shouldn't be much of a problem. They are not made by Samsung itself and if it's not working and still refuse to buy a new glass, I'd just go to a repair shop as I did here in the Netherlands and ask the repair guy to order it. It shouldn't cost more than a few bucks. On top of that just google "note 2 screen adhesive" and look at some amazon/ebay hits, just take that picture/info to the repair guy as a reference to know what to order
Click to expand...
Click to collapse
Im from the netherlands too, which shops do you recommend? I bought my phone at coolblue, but I dont want to lose my phone for 2 weeks with repair..
Sent from my GT-N7100 using xda app-developers app

Ghetto_Cowgirl said:
I shattered my screen a few weeks ago and had great results replacing just the glass, not the digitizer, however I have a small problem. I didn't realize the adhesive was still on the LCD, I kind of ruined it along the left side of my phone, it doesn't stick properly, kind of looks like a bad screen protector. I have to keep pushing it down to get rid of the haze. What I'm wondering is, can I remove the adhesive all together and just replace the sticker bit along the border of the glass, so there's no adhesive between the glass and LCD without it affecting the performance of the touch screen? It works great as is, the haze is just annoying me.
Any help would be greatly appreciated, I'd hate to do it and lose the ability to use my phone
Sent from my Samsung Galaxy Note II using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
Check out the link in my signature. You'll find what you're looking for with regards to the adhesive.
Sent from my GT-N7100 using xda premium

[Q] Shattered glass

So, I shattered the glass on my Galaxy S3 today. It's pretty messed up (see the attached picture), but the touch works, even in the damaged areas. So it seems it's only the glass that needs to be replaced, with something like this:
http://www.ebay.co.uk/itm/Blue-Fron...K_Replacement_Parts_Tools&hash=item417515ee67
Correct?

Yep, goodluck. Replaced the same on my Galaxy Note 2. all good now.

Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.

1slow4G said:
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
Click to expand...
Click to collapse
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.

MadsBen said:
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
Click to expand...
Click to collapse
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2

Actually the glass on an s3 is just that, glass. The digitizer is fused together with the LCD. However glass is glued to the LCD which can make it very difficult to replace. If you've never taken on the repair of a screen before then I would say you'll be more likely to break the LCD than not in your replacement of the glass. But again it is possible if you are very slow and very careful. As someone else mentioned though it's much easier to replace the whole assembly.

It didn't went well. I wasn't too carefull. In the bottom, the glass was too shattered, so when I tried to lift it, a piece with glue got stock and lifted the digitizer. So now that don't work. I'm not gonna spend £100-120 on a new digitizer, I'm gonna settle for my good old Nokia 6300i (and Nexus 7...) and wait for the Nexus 5.

I would wait for the n5.. gs3 is a dying trend already.

Its hard like everyone said , if your really gunna do it watch videos online and be prepared. If you know anyone that has done it successfully ask for help or tips
ouch didnt see u tried it already

the same happened to me on my wife's white sgs3 trying to be the savior of the day turned out to be an expensive digitizer replacement of $200 instead of the $8 glass replacement. I rushed the glass removal and cracked the lcd screen. I could have ordered one on ebay for $100 but wife needs the phone the next day so i decided to get it repaired locally.

Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.

My 2 cents
bidibull14 said:
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
Click to expand...
Click to collapse
Wanted to warn that changing the glass is not for everyone. It takes patience and zen. If you rush it, you will likely break LCD and spend even more $$$ that you would have otherwise. Also following notes:
1. Watch at least a couple of youtube videos before starting.
2. Heavy duty heat blower works much better than a hair dryer. Of course, don't go crazy, as it's possible to melt the phone with it
3. S III has a wire at the bottom (the one which goes to the buttons). If you damage it, you will need to replace whole LCD, there is [almost] no chance you will be able to fix this wire. So, always start removing glass starting with the top of the phone
4. Heavily cracked glass is hard to remove, as it crumbles. To make it easier, a) put a scotch tape on top of glass, so that the small pieces stick to it, and b) use a lot of heat
5. Everybody advises to use plastic tools, personally I used swiss army knife with high level of success, and never had a problem scratching LCD. Your mileage may vary, but using metal blade certainly makes life much easier, especially in heavily cracked glass situation.
6. If you do use blade, it often is enough to get blade just a little bit under a glass, and then simply apply heat. Big chunks will unglue all by themselves.
7. Remember, that failure is always an option. Don't use it on the phone, if you know that you desperately need it working right this day, if you don't have a plan B.

1slow4G said:
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Click to expand...
Click to collapse
same freezing issue on mine... apparently the hardness of Gorilla2 is much greater than the knockoff glass replacements. The replacement glass on ebay and kijiji may not be authentic and that is why it bends slightly when pressed harder (in fact mine cracked completely when I applied too much pressure)

i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?

hani93 said:
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
Click to expand...
Click to collapse
I've heard about that glue too. I'm considering switching mine, because when I repaired I reused the glue of the original glass, and know I had dust between the glass and the lcd -.-
My concern is about the uv light, don't know if we could put in the sun to substitute it.

I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.

m1batt1 said:
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
Click to expand...
Click to collapse
it's not that hard to remove factory gle there..
for example, i removed mine, by rolling the glue with fingers.
just make sure, that you don't apply too much pressure to lcd.
and after that, clean up lcd form dust/fingerprints, and you are good to go.
and for removing glass, i used usual/ stronger kitchen knife (attached picture).

i replaced my glass 3 months ago.
i use normal hair dryer to remove glass and glass comes out almost as whole except for small broken pieces.
i think my scratch guard help in that.
i didnt use any additional glue or uv light.
nonresponsive screen is issue but only when you press too hard and press of power button resolve this issue.
but whole process of replacing galss took 2hrs

Oneplus X Glass Repair

I recently bought a cracked oneplus x in hopes of fixing and using it. So I went ahead, heated it up and took the glass off. This went fine. I set the heat around 90-100° C and the glass came off just like it would from any other phone. The display is only glued on on the sides/bezels unlike Samsung phones in which the whole panel is glued down. This obviously made things easier. To my surprise the loca came off pretty easily with some rubbing alcohol. Before removing the glass you have to take off the soft keys, which are glued to the glass. These are connected to the back of the screen assembly by a connector which you can see in the pictures. It was when I went to buy the part I realized I had made a mistake: I couldn't find any. So I am stuck with this for now, and if anyone knows where I could buy the glass please give me a link. Regardless, I hope this is informational and helpful to anyone who might want to attmept this in the future.

mnath said:
I recently bought a cracked oneplus x in hopes of fixing and using it. So I went ahead, heated it up and took the glass off. This went fine. I set the heat around 90-100° C and the glass came off just like it would from any other phone. The display is only glued on on the sides/bezels unlike Samsung phones in which the whole panel is glued down. This obviously made things easier. To my surprise the loca came off pretty easily with some rubbing alcohol. Before removing the glass you have to take off the soft keys, which are glued to the glass. These are connected to the back of the screen assembly by a connector which you can see in the pictures. It was when I went to buy the part I realized I had made a mistake: I couldn't find any. So I am stuck with this for now, and if anyone knows where I could buy the glass please give me a link. Regardless, I hope this is informational and helpful to anyone who might want to attmept this in the future.
Click to expand...
Click to collapse
You can buy it from here
http://vifocal.com/oneplus-x-lcd-display-with-touch-screen-panel-replacement.html

loveboy_lion said:
You can buy it from here
http://vifocal.com/oneplus-x-lcd-display-with-touch-screen-panel-replacement.html
Click to expand...
Click to collapse
I was hoping to do a glass only repair with loca uv glue since the glass alone is substantially cheaper. Thanks, however, I atleast have that as a backup, since it is at a pretty reasonable price for an amoled panel, if it takes too long for the glass to be available.

till now .it seems only this site sell the oneplus x lcd display.it looks like a professional website and can be trust
Send from my Oneplus Using Tapatalk

Maybe you should go to aliexpress.com and the keyword is oneplus x glass screen
Maybe it will help you

heres a link for one:
http://www.aliexpress.com/item/1PCS..._2&btsid=3a76fb04-754a-42d0-b51b-7b076dca6b80

mnath need your help
m opx screen got a crack after it fell down Touch is working and i had initially thought of replacing the entire set which cost around 8k but after reading your thread i feel it can be done by replacing just the cracked portion.
Can you guide me on how to get it done ? pls ping me on whatsapp 9633318375 (Sony, kerala)

Could you pls tell me how to put the glass of the phone ? Ping me on whatsapp (081282213266) isya pramesta

I would also love to know how you got the glass off!
I bought the glass by itself, and I'm hoping that I would be able to recreate your result, so if you can tell me a bit more about the process that would be nice!

Did anybody get more details pics/instructions on just replacing the glass, mine arrived today and I would like to get it done?
Also does anybody have a specific recommendation on the LOCA adhesive to use to glue the glass back on?
Z

Ghh
---------- Post added at 02:59 PM ---------- Previous post was at 02:54 PM ----------
Please any one suggest me how to replace only the front glass of one plus x

This is above and beyond being that the part for glass+LCD is like $30 on ebay.. Like you're risking the fact that the adhesive is like a little worse and a sunny day could easily destroy everything. If you're going to repair this phone, do the glass and LCD together.

Thanks for your reply...

mnath said:
I recently bought a cracked oneplus x in hopes of fixing and using it. So I went ahead, heated it up and took the glass off. This went fine. I set the heat around 90-100° C and the glass came off just like it would from any other phone. The display is only glued on on the sides/bezels unlike Samsung phones in which the whole panel is glued down. This obviously made things easier. To my surprise the loca came off pretty easily with some rubbing alcohol. Before removing the glass you have to take off the soft keys, which are glued to the glass. These are connected to the back of the screen assembly by a connector which you can see in the pictures. It was when I went to buy the part I realized I had made a mistake: I couldn't find any. So I am stuck with this for now, and if anyone knows where I could buy the glass please give me a link. Regardless, I hope this is informational and helpful to anyone who might want to attmept this in the future.
Click to expand...
Click to collapse
If you only need the glass it is available on ebay :
http://www.ebay.com/itm/Black-Front...317149?hash=item235e06281d:g:DGgAAOSw6n5XwQUT
I have few questions, what did you use to heat up the display ? I don't have a heat gun, will a hair dryer do the job ?
Also are there any ribbon cables which I need to be careful about while doing the process?
Thanks in advance!

mnath said:
I recently bought a cracked oneplus x in hopes of fixing and using it. So I went ahead, heated it up and took the glass off. This went fine. I set the heat around 90-100° C and the glass came off just like it would from any other phone. The display is only glued on on the sides/bezels unlike Samsung phones in which the whole panel is glued down. This obviously made things easier. To my surprise the loca came off pretty easily with some rubbing alcohol. Before removing the glass you have to take off the soft keys, which are glued to the glass. These are connected to the back of the screen assembly by a connector which you can see in the pictures. It was when I went to buy the part I realized I had made a mistake: I couldn't find any. So I am stuck with this for now, and if anyone knows where I could buy the glass please give me a link. Regardless, I hope this is informational and helpful to anyone who might want to attmept this in the future.
Click to expand...
Click to collapse
Hey, thanks for this information. Could you olease guide me once through the process in detail. I dont want to make any mistakes. Whatsapp me on+91-8821099326 . Thanks it will be very generous of you

Sparsh01 said:
Hey, thanks for this information. Could you olease guide me once through the process in detail. I dont want to make any mistakes. Whatsapp me on+91-8821099326 . Thanks it will be very generous of you
Click to expand...
Click to collapse
Search Youtube videos, it wil be helpfull

Kéno40 said:
Search Youtube videos, it wil be helpfull
Click to expand...
Click to collapse
Yeah, i did. But no video for oneplus x.
And since it has a super amoled. I dont want to take any chances.
I have only one shot.

Totally agree with all of you, I recently purchased just the front panel glass and really wanted to replace it, only for my local phone repair place won't do it without the lcd and digitizer... If someone can post pics or tell me if a hair dryer will do the job, I would give it a go myself

SenorAfro said:
Totally agree with all of you, I recently purchased just the front panel glass and really wanted to replace it, only for my local phone repair place won't do it without the lcd and digitizer... If someone can post pics or tell me if a hair dryer will do the job, I would give it a go myself
Click to expand...
Click to collapse
Bro you can watch Jerry Rig Everything videos of glass only repair of S4 and s5 in which he separated the glass with a hot gun and playing cards. Plz do share your photos also if you do repair..

Guys found a video on youtube of oneplus x glass only repair -----> https://www.youtube.com/watch?v=Vs1iXlBoYAM
share also you repaired glass pics also to help others also....
don't forget to hit the Thanks! button