Develop Bugs

Screen died?

Last night I was out and during the night I pulled my desire z out of my pocket to find that the screen was dead, the soft touch buttons were still lit up and working but no display. I pulled the battery and tried to reboot and no luck, you can hear it booting and even unlock/receive calls and txts etc once it has booted up just the screen stays blank the whole time so have to do everything on feel.
Essentially does this just mean my screen has a hardware fault? is it worth trying to fix? I assume the only option would be to purchase a replacement screen and dissemble and reassemble it?
(warranty is not worth it as I live in New Zealand and would have to send my phone back to the UK where I bought it from, also I have dropped it quite a few times so probably voided anyway...)
Thanks in advance for any input

Does it never display anything? So not even a flash during boot or something?
Because then it is probably a hardware problem.
Since the soft touch buttons do still work I think there might be a little crack or something in the flat cable that connects the bottom half with the top.
Maybe you could check whether you can see if the cable is broken or not?
The best thing to do then is to look for a replacement and try to fix it yourself or bring it to a shop where they can do it for you.

No it never displays anything, completely dead the whole time. The touch input is still working though as I answered a phone call this morning on it by making the usual gesture just without being able to see anything. Doesnt seem to be anything wrong with the cable itself as far as I can see. Yea might have to get someone to have a look at it.

My phone is acting the same. I dropped my phone in the pond before, but pulled battery out on time and had it in rice for a day. My phone was still working for about two weeks after that incident. I dropped it and had one little crack at the top of the screen and about a week after that it died when I had a water balloon fight with the phone in my pocket. D;
Do any of you know if the replacement lcd screen/digitizer for the Desire Z would work for the G2?

I had the same thing happening to my G2 screen, only it was intermittently working for a little while, then just completely died and wouldn't work. It was doing this crazy flickering thing then the back light wouldn't go on at all. If I held the phone at a certain angle in the sun, I could see that the pixels were indeed working on the display, but there was no backlight to make them normally visible.
So I purchased a replacement screen from ebay and carefully followed the directions on a youtube video for a G2 take apart. Its not a hard task to take apart and get down to the screen itself. It was rather easy. After putting it back together the screen still didn't work! Sounds work, i can also receive calls etc. But the screen still doesn't work!
Is there any way that this could be a software issue?

Oh and PS, I believe the LCD replacement would work for both the desire Z and the G2. They are identical phones after all right? I'd say its a safe bet. The screen I bought was only 35 bucks. Didn't think that was a bad deal.

Another dead screen or something else?
Few days ago my phone fell of the couch onto a rug - no big deal, so far it has survived much worse, but when I picked it up, the colors were all messed up - overly green and red. Tried restarting - no luck. Everything worked fine, except the colors, but then the screen turned of completely. I could hear notifications, phonecalls, but the screen was dead. After some tapping on the screen, it turned on again - with ****ed up colors. Then started flickering and was gone again. Few more times I could turn it on by tapping before it was dead for good.
Figured, after all these drops it survived, maybe the screen connector is a bit loose. I mean, I could sometime get a contact when tapping it, so I dissasambled it completely, secured all the connection, put it all back tougether and fired up - same thing: dead screen, phone working.
Has anyone had such problem before? Is it screen that is dead, or connector or... I have no clue... I would like try to fix it on my own, with some replacement parts I could get on ebay - but, what gave?

Strip of touchscren not working

Hi guys. I know many of you have had touchscreen problems and whatnot, i searched but it seems like this one is a bit different from usual. Yesterday the phone was totally fine; i woke up this morning and it had a lot of touchscreen problems: at first it registered touches without me doing anything, but after a couple of reboots it was just unresponsive. After another reboot and some messagging, the problem reduced to a strip on the screen simply not working. The strip is located exactly where the first notification on the status bar is (like when you receive a message and you click on that notification). I have the trueancestor stats bar buttons, so that zone is a tad more down than usual. Anyway, all I did yesterday was a quick game. I think it may be the flex cable not working because of the sliding, but it happened all of a sudden, not gradually. I must say that some weeks ago I had the same "registers touches by itself" issue when typing, but a simple reboot was enough. I tried doing factory reset, but nothing so far. Also I can't use pc companion to flash everything stock back (I unlocked bootloader months ago, even though I relocked it; I dunno if it's locked or not right now), and I can't seem to find a working flashtool download link -_-. I don't think that would help much, it probably is a hardware problem, but who knows. I'm on true ancestor 1.6 LE, stock kernel.
Any help would be great, as I fear the phone will get refused in assistance because of bootloader unlocking.

Did your phone had contact with water? When my screen had contact with water it registered touches randomly.

it didn't. it has a screen protector anyway; but that's not the problem for sure. it doesn't register randomly, simply a strip doesn't work now...

Hardware problem. Could be flex cable or digitizer.

Today there were two moments it began to work again, but a few minutes after each one the problem came back. Sigh...

Mine does that when the screen is moist or my hands are too oily. Are you sure you're working in a dry environment?

mhh... exactly that? I dunno, my hands are dry and i think the screen is too; it has a quite thick screen protector (the skinomi one), so even if it got moist that shouldn't be a problem, right? I'm now living in a different town and that may have changed something, but the problem didn't show up until now, and it was sudden.
Also, I noticed that using gamekeyboard on a certain profile I had buttons placed on the strip, and pressing hardware keys mapped to those buttons actually works. This restricts the problem just to the actual finger-touch-detecting mechanism. Does anyone know anything about this?
Edit: lol I heated the phone up a bit with a hair dryer. It works now. I hope it will last and I'll not have to do this again over and over

Black Screen, phone still works?

Hello XDA members, this time I'm writing to all of you to tell you something that happened to my Optimus G E987 from Claro Argentina, also, to ask you something related to the topic.
I bought this phone about 4-5 months ago, and I have taken really good care of it, without using any film protection or case, it was working perfect and with not a single scratch on it, not even a little hit.
But then, some days ago, I decided to "protect it" a little bit, so I got one of this:
htt-p://i[dot]imgur[dot]com/YtgK1aS[dot]jpg
htt-p://i[dot]imgur.com/la1kI5e[dot]jpg
(Sorry, I'm new to this forum so it won't let me post links)
I used it like.. dunno, 3-4 days. One night, my phone was on 53% battery, to lazy to charge it so I just let it like that. Next day I gave it some use, so it dropped to 33% of battery life, I had to go work so I turned it off. When I finished, I tried to turn it on again, but nothing happened, tried more times and nothing, then I noticed I liiiitle light in the screen, the phone was turned on, but with REALLY low visibility, almost everything black but with a little of sight.
I though it was just a battery problem, so I charged it, but to my surprise, nothing happened, well something did happen, the little bit of sight that I had just went full black with no visibility. I noticed that the touch screen and buttons actually worked, I could "easily" navigate through the phone by just using it as normal, but without seeing (you can do this by just knowing your phone a bit).
And that's the story, basically, after using that case, the phone "casually" stopped working properly, all I got was a functionally phone with a black screen.
I managed to connect it to my pc through wifi and launched Android Screen Cast, to see what was happening on my phone. The glow was at 100% (I tried changing it) and everything seemed normal.
If you don't want to read, here is a TL;DR
>Bought Magnetic* Flip Stand Leather Wallet Case for Optimus G
>Some days after, phone screen stopped working (phone was still normally working, just with a full black screen)
About the Magnetic thing.. is there any possibility that this was the problem? the magnetic thing?
Btw, I sent the phone to tech service because it was still on warranty and they have me a new one, now I'm scared of putting it again in the leather case I bought, I don't want this to happen again.
Something to comment? hope you can give me some advice, thanks in advance!

Also having similar problems as you. Somehow, i am quite sure its the stock rom causing the problem.

Had the very same issue few weeks ago, had to send the phone back to LG ( who replaced the motherboard :/).
I was also on stock rom, had root and unlock bootloader (of course I clean all that **** before sending it back).
For my part, I was unable to go to recovery and download mode was quit impossible to access (may be my finger fault )
BUT! some time if I let the phone off for a moment or spam the power key, the backlight turn back on until I power down the phone, so it's could be a software issue ...
Anyway, an other info, when the backlight was off, if i tried to change backlight level i was getting a error message about overeating or something like that...

[Q] Part of the screen is not responding to touch... help?

So during my holiday my HOX got splashed with a bit of water from a wave. The battery was running on fumes and, when I looked at it, the phone was dead. It did turned on later while in my pocket and I happened to press the power button.
I let it dry on rice and nothing. I made the potential mistake of trying to charge it so it would heat up and it wouldn't charge. I then bought another mobile and, just to try it, I took opened the HOX and hoovered. Nothing.
Miracle happened yesterday when, just for kicks, I tried the charger again. It power up!! Everything seems fine, no visible screen damage, wifi works, everything works just fine but... screen won't respond to touch on the very bottom, say, the capacitive and menu buttons (the ones just above the capacitive ones).
What do you guys think? Is the screen dead there, maybe I didn't put the screen back properly or should I wait as some moister might yet be there?
Cheers!

Kutusov said:
So during my holiday my HOX got splashed with a bit of water from a wave. The battery was running on fumes and, when I looked at it, the phone was dead. It did turned on later while in my pocket and I happened to press the power button.
I let it dry on rice and nothing. I made the potential mistake of trying to charge it so it would heat up and it wouldn't charge. I then bought another mobile and, just to try it, I took opened the HOX and hoovered. Nothing.
Miracle happened yesterday when, just for kicks, I tried the charger again. It power up!! Everything seems fine, no visible screen damage, wifi works, everything works just fine but... screen won't respond to touch on the very bottom, say, the capacitive and menu buttons (the ones just above the capacitive ones).
What do you guys think? Is the screen dead there, maybe I didn't put the screen back properly or should I wait as some moister might yet be there?
Cheers!
Click to expand...
Click to collapse
This is a flashback to me. Same thing happened to me few weeks ago - first 3 bottom buttons stoped working, and now 7 days ago part of touch screen is not working anymore. I am going to replace lcd+digitizer+frame, lucky me nothing else need to be fixed. And IMHO trying to heat closed HTC when water was in it doesn't make a sense as a water will condense (as it is closed) so it would make more damage. Oxidation sucks :/

I do have the SIM slot opened but yeah, that's a tinny opening, not much space for water vapour to escape... it's been a few weeks since I thought it had died though, it's pretty amazing to me that it came back at all. Some tough phones, these...
Anyway, I think I'll try to take the screen out again, I wasn't too careful putting it back in because I saw it wasn't charging or powering up or anything at all.

OP 3 shuts down after I lock it

Hi there,
I recently changed the screen of my OP 3 because it fell on the floor and did not show anything afterwards (I don't know if this only damaged the screen or also other parts of the phone).
Now, the screen works very well and and the phone does turn on as well (I even type this with my OP3). But I now have two problems:
1) My phone shuts down almost immediately after I lock it (after one or two seconds I can still unlock it but after 5 seconds or so it is dead). It does not shut down while the screen is on, though.
2) It heats quite a lot during using and especially during charging. I know, this seems to be a general issue with older OP phones and happened to me as well, but never to that extent (after charging 30 min it gets overheated which never happened before).
Plus, there are two issues that might or might not be related to these to problems so I add them as well: My volume control buttons did not work before the screen replacement, which is quite odd, because the power button works well. And I think I have destroyed the home button/fingerprint scan while changing the screen.
What do you think, is there any hope of solving these problems without having to buy a new phone?
Best, thank you all!
Clemens

Oneplus 3's sides buttons assembly is really fragile. When i was replacing my screen i replaced it too. With my second display, i broke the replacement button ribbon and installed the original one. So you might broke it.
For screen issue, are you using latest OxygenOS? Because some custom roms have issues with third party displays.

clemenssayshi said:
Hi there,
I recently changed the screen of my OP 3 because it fell on the floor and did not show anything afterwards (I don't know if this only damaged the screen or also other parts of the phone).
Now, the screen works very well and and the phone does turn on as well (I even type this with my OP3). But I now have two problems:
1) My phone shuts down almost immediately after I lock it (after one or two seconds I can still unlock it but after 5 seconds or so it is dead). It does not shut down while the screen is on, though.
2) It heats quite a lot during using and especially during charging. I know, this seems to be a general issue with older OP phones and happened to me as well, but never to that extent (after charging 30 min it gets overheated which never happened before).
Plus, there are two issues that might or might not be related to these to problems so I add them as well: My volume control buttons did not work before the screen replacement, which is quite odd, because the power button works well. And I think I have destroyed the home button/fingerprint scan while changing the screen.
What do you think, is there any hope of solving these problems without having to buy a new phone?
Best, thank you all!
Clemens
Click to expand...
Click to collapse
Most likely a hardware issue. To confirm, clean flash OOS latest version (9.0.6 I think) and check. If it is ok, your problem is solved. If not, there are too many variables (screen, volume, home button and any other thing that you disturbed while replacing the screen) to trouble-shoot.