Develop Bugs

Extended Battery Life on Kaiser

Man, I hate starting new threads! I did a simple search and couldn't find this problem anywhere else, so here goes:
Earlier in 2009 I bought an extended 2400mAh battery for my Kaiser (8925). Everything is working just fine, except that I noticed that the phone doesn't seem to notice that the battery life is much better for this new battery.
What I mean is: after a few hours of usage, the battery level drops at a normal rate.
Once the phone tells me the battery is almost dead (and sometimes the phone will shut off if I ignore this), I can shut down the phone, remove the battery, wait a few seconds and then replace it and boot back up the phone.
At this point, the phone will usually tell me that the battery is at 33% to 36% charged. Notice that I did not charge the battery, I just removed it and put it back in.
When I first got the battery, I cycled it completely three times in the phone, removing it twice and replacing it to ensure that the battery was completely drained before charging it to 100%. (Yes, I know that is only recommended for metal-hydrates, but I feel better doing that anyway).
On the top-end, it usually takes about two hours to charge the phone from 30% to 99% via a standard USB2.0 connector.
However, the phone will report that the battery is not fully charged for nearly an hour after reaching 99%.
I know what you are probably thinking; Why is this guy complaining about his battery performing better than his phone reports?
Well, it IS kind of annoying. I would like the phone to properly report the remaining percentage for my own benefit. I really hate having to guess at how much time I have left before I need to drop it off at a computer or wall outlet while I find something else to play with for three or four hours.
So... Does anyone know how I can convince my phone that the battery is pretty awesome and to start reporting the actual battery life?

[Q] Instant discharge.

So, I'm on my Evo today, playing a game (Air Strike). My battery is at 93% when I picked the phone up to play, and the phone is plugged in. Suddenly, with no warning what-so-ever, my phone shuts off. Of course a mini-freak out and many "wtf's" ensue. No warning, no signs, even the led went off. I pulled the battery, put it back, then plugged the phone in again. After that it gave me the blinking light indicating the battery was too low to turn on. After a few minutes charging she came back on and battery was at 5%.
How the hell does a battery go from 93% to 0% in less than 5 minutes, and give no warning at all?? Anybody else ever have this problem?

Wow I've have never heard or that happening before. Maybe a glitch in the battery stash? Did it take awhile to charge up to 100%? Can you reproduce the issue again?
Sent from my EVO (CM 6.1.1) using XDA App

I had this problem with my older phone once. The battery itself may have a problem or your phone is not getting charged properly.
Try These :
1) Try charging the phone overnite from the Wall charger (Not through USB of your computer)
2) If the above does not work, and you have access to another evo battery, then try using that.(try using a friends battery and charger for a day. ) (Ofcourse needless to say the charger and battery must be for Evoonly )
In my case, my phone started working fine again after getting my battery & charger replaced.

Probably shouldn't worry about it too much just yet. Could be something as simple as your battery meter was mis-calibrated. The meter itself is software so it can easily be wrong/off. If it continues you may have a bad battery.

Sounds to me like something is wrong. Did you just get the phone or have you had it?

Idk... The phone had been plugged in for most of the day (hadn't gone anywhere. Lazy day lol) And like I said, the led went completely out as well.
Haven't had the problem again, so we'll see I guess....

Mark_Hardware said:
Idk... The phone had been plugged in for most of the day (hadn't gone anywhere. Lazy day lol) And like I said, the led went completely out as well.
Haven't had the problem again, so we'll see I guess....
Click to expand...
Click to collapse
I've seen some posts about the Evo battery shutting off the charge when its being used. Were you using your Evo while it was charging?
If the battery doesn't seem to be giving you percentages that are accurate, you might want to recalibrate your battery.
Common misconceptions sticky (Evo Q&A) said:
Battery recalibration (Thanks to Cyanogen for this and to fachadick for bringing it to my attention).
If you're experiencing higher than normal battery drain, try the following:
1. Charge the phone to full battery; let it keep charging until the battery says it is fully charged. Do not just wait until the light is green, it isn't always fully charged, causing a lot of inaccuracies. (You can check by going to: Settings -> About Phone -> Status -> Battery Level = Full.)
2. Boot to recovery and wipe battery stats.
(To have the most accurate of battery stats, reboot the phone immediately after wiping the battery stats and wait for your ROM to boot completely to the desktop. Once your entire boot is done and you have full access to the phone, go ahead and pull the charger and continue.)
3. Do not charge the phone until after draining the battery completely, resulting in it automatically shutting off. Take out the battery, and keep trying to turn on your phone until it will not turn back on at all.
4. Recharge the phone completely and then use as you normally would.
This is a method that has been proven to work, I am sure there are other ways. My battery lasts longer after doing this and the reading is much more accurate. It might be advisable to do this after every ROM install if you want the most battery life and most accurate battery reading by the phone's software.
Click to expand...
Click to collapse

[Q] Weird battery discharge

Hi fellas..
Maybe you've noticed the messages I've sent to Unofficial BravoS thread of Coolexe's (http://forum.xda-developers.com/showthread.php?t=1200517&page=51) which is the ROM I use.
The issue is, the battery discharges rapidly. Actually, if you check mV values, it doesn't discharge rapidly, but if you look at percentages, there is a huge inconsistency. I used Battery Monitor Widget to log the battery performances last night, and saw these horrible results:
Code:
2011/09/19|04:59:49|-515mA|37%|3581mV|40.2ºC|1|0
2011/09/19|05:00:51|-465mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:01:49|-460mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:02:50|-462mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:03:49|-477mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:04:50|-471mA|34%|3449mV|40.3ºC|1|0
2011/09/19|05:06:06|-478mA|0%|3415mV|40.5ºC|1|0
2011/09/19|05:06:08|-478mA|0%|3415mV|40.5ºC|1|0
These are the last lines of the log, before the phone shuts down. As you can see, the phone gone to 0% from 34% in one minute! No low battery warnings or whatsoever..
Funny thing is, this doesn't happen in StarBurst ROM (which is a Froyo based one). Do you reckon this is a GingerBread issue or something? I saw some other people complaining about their phone shutting down at 20% as well.
So, what do you suggest?

when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance

crendot said:
when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance
Click to expand...
Click to collapse
This is what I've done so far:
Drained battery to 0% (log above) and charged it a little bit while powered off (like 20%). Turned on the phone, and obtained those logs (last lines only):
Code:
2011/09/19|14:41:25|-268mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:42:25|-267mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:43:25|-270mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:44:25|-269mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:45:25|-267mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:46:25|-268mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:47:25|-266mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:48:25|-267mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:49:25|-269mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:50:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:51:25|-266mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:52:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:53:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:54:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:55:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:56:25|-266mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:57:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:58:25|-268mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:59:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:00:25|-319mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:01:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:02:25|-270mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:03:25|-269mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:04:25|-270mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:05:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:06:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:07:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:08:25|-289mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:25|-290mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:51|-290mA|0%|3464mV|38.3ºC|1|0
It seems more "smooth" discharge now. Right now, I'm charging my phone off; going to turn on phone once it reaches "green light" with charger on, and plug it off once phone booted. Maybe then, it can know what's maximum and minimum.
So far, I tried to charge my phone to full and erase batterystats.bin but, as you can see at the first post, it didn't work well.. On the other hand, the phone charged-discharged only once in this ROM, you think it could be better if I've given a "second chance"?

i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains

crendot said:
i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains
Click to expand...
Click to collapse
I know, but when phone thinks it's 30% and not warn me, how can I do it?

In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!

TVTV said:
In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!
Click to expand...
Click to collapse
Thanks for your answer...
Today I realized that it my concern was a quick one. Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process. After that, I let the phone to discharge (I helped it a little )
I actually saw "Plug your charger" warning this time, and according to Bat. Mon. Widget, it gone down until 13%! If I do compare the mV values with the old ones, I can see that somehow the phone does learn which mV value correspond to which percentage better.
Even though it gone from 13% to 0% in two minutes, it's at least better than 30% to 0%.. Also, when I check the readings after I plugged in, I saw that percentage-voltage matching is slightly higher, showing that the phone now shows lower percentage for the same voltage - which shows that it learns percentage better.
After one or two charge-discharge cycle, I think it'll learn absolute 0
BTW; the battery says 3.4V 1400mAh and my maximum voltage is 4160mV (100%) and minimum is 3415mV (0%). Are these values normal, you think?
PS: What I'd recommend from anyone who loves flashing ROMs as much as I do is: AFTER YOU FLASHED A NEW ROM, CHARGE YOUR BATTERY TO FULL (100%) AND ERASE THE BATTERY STATS. AFTER THIS, NEVER, I SAY, NEVER ERASE YOUR BATTERY STATS FOR LONG TIME IN ORDER FOR YOUR PHONE TO LEARN STATS BETTER! Erase after long time, say 3 months for wear effects to be accounted, but well, I think you should be fine even after you don't do this
Maybe you did already know that, but, well, I learned it hard way
EDIT: Phone shutdown at 13% after this, but I think it'll do better in time..

Can't Calibrate the Widget
I am having a similar issue with my htc aria. Problem is that it gets to about 78% and then won't go any higher. It even shows (in Battery Monitor Widget)
"Discharging" and "AC plugged". I have let it sit plenty long enough to be fully charged and then completely discharged it (until it shut itself down, which was not 0%) and recharged until it reaches 78% again and stops charging. I'm guessing it is so far out of whack that it says I'm at 78% but I am really at 100%.
The widget says to charge to 100% and then drain completely to 0% to calibrate. I can't do either from what I can tell. So what to do?

theGanymedes said:
Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process.
Click to expand...
Click to collapse
Quick tip - let the phone charge for another hour or so after the light goes green (when charging it while powered off). I've read that the light goes green at about 95%. It takes another hour for the phone to really charge to 100%. That's because Li-Ion batteries use two stages to charge: a fast one and a slow one. More details here.
Glad i could help.
P.S. - It also took me two complete charge/discharge cycles to fully calibrate my battery meter after switching from FroYo to Gingerbread.
@vkyjackie - Try fully charging the phone while powered off. If it still doesn't fully charge (LED green), then you might have an issue with either the battery pack or the wall charger.

[Q] Battery worn out?

Hello,
My desire, after:
an inability to restore nandroid backup
a possible corrupted sd card
a usb brick and inability to mount some nand partitions
and finally succeeding in fixing it, now using/running:
2.29.405.5 stock rooted rom
a new sd card (samsung 16GB class 6)
clockworkmod 2.5.0.7
s-off
seems that has battery issues. When it reaches below 30%, it drains a lot faster. In example few minutes ago, the battery was below 30% level and after sending a couple of sms messages the phone, without the "Connect the charger" indication shut down. Not even the battery icon was red.
What should I do?
After flashing the above ROM I ran an app called battery calibration (could this be the culprit?).
I haven't experienced such problems before the whole mess mentioned above.
Thank you for your time.

Well, it seems to me like a "classic" battery meter calibration issue.
TVTV said:
In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!
Click to expand...
Click to collapse

Did this work you mate? I have the same issue with my year old batter now... the phone shuts down @ 40% without any warning... and when I charge it, it starts from 0% and as soon as it hits the 58% mark, it jumps to 100% by itself... and i cant seem to figure out what the hell could I do to fix it... I tried calibrating the battery using the awesome method described here http://forum.cyanogenmod.com/topic/11823-battery-calibration-thread 3 times and nothing changed...

bump bump.. i really need help on this guys... :/
Sent from the infinity and beyond...

Weird that after calibration you still get that kind of issues, does this only happen on your current ROM? I have the latest CM in my desire and everything works just fine... Maybe try another ROM if calibration doesn't work to see if it's a hardware or software issue

i actually had issues with MIUI first.. the phone randomly shut down by itself but when i turned it back on, it was perfect... then i switched back to Oxygen and while everything was fine, suddenly one day the phone died at 40% :S and from that day on the phone charges to 58% and then instantly jumps to 100%... and as soon as it gets to 40% it shuts down itself... i guess i need a new battery but i wanted to see wether i can fix this one somehow so i can use it till the new one arrives...
Sent from the infinity and beyond...

same problem
i have the same problem
my phone turns off at 20% battery
calibration does not help....
and battery is not bad - it works fine
i'm sure its the problem with calibration

kshitijgandhi said:
i have the same problem
my phone turns off at 20% battery
calibration does not help....
and battery is not bad - it works fine
i'm sure its the problem with calibration
Click to expand...
Click to collapse
phone turning off at 20% is fine mate because thats the battery guards against any damage
most of the phones ( smart phones) switch off at 20% as going lower can damage the System .

It shouldnt normally..It's supposed to work fine upto 5%

Have a look at this, it worked for me (but you need a compatible kernel, most AOSP are so)
http://forum.xda-developers.com/showthread.php?t=765609

Shutdown at ~25% with new battery and 20% with old

Hello,
I've read the threads about battery in the desire, BATT FIX with new kernels etc but can't really find a definite answer for my problem.
I bought my phone 18 months old and from the beginning it has shut down at about 20%. Tried the battery thing with charging, on/off, charing again etc, wiping battery stats etc but it doesn't seem to matter. So, I thought I'd just buy a new battery and be done with it.
The new battery arrived yesterday (actually, it's a used battery from customer returns but seller tells me it's been tested to be in mint condition). So this battery shows 3% when I first start up with it, "good, this seems to work" I think. But when at 75% the charger indicator (LED light) all of a sudden turns green and battery % jumps straight to 100%. I do the battery calibration trick with on/off charge and wipe battery stats. Stuck at 100% for some time as reported by others trying this "trick", have been using it all day and it shuts down at 25% even worse than the other battery...
The best voltages I've seen on this supposedly new battery is 4,144 and somewhere above 3.5 (nowhere near 3.2 and 4.2). What strikes me as odd is that I get very close to the same values with my old battery so I'm starting to think that maybee both battery are good but the phone reports way wrong values...is this possible?
Battery life with phone and data connection on, 1 gmail account but disabled backup feature (no GPS, BT etc) gives me -5% after 10 hours standby and I can use the phone for browising, light gaming for about 3 hours and 40 minutes before it dies (more or less constant usage at very low autobrightness levels and Turbo 3G enabled).
If someone has some insight into this it would be really helpful before I contact the eBay seller for this particular battery.
Regards, Olle

Same thing
My phone shuts down at 35% now... Is that a problem with the chipset or what? Only with Alex-V's calibrated kernels my phone shuts down at 0%, and sometimes it decalibrates too, but after calibration is Okay. I wonder if i need a new battery or my chipset has issues.