Develop Bugs

not charging via usb?

so the option to not charge it is not ticked under power settings, and its set to charge via usb from advanced config and still no dice.
tried different usb ports and nothing
the led is orange, says its charging in power options
any thoughts?

Try a diffrent usb cable, some cables do not provide enough power to charge the phone. (guessing maybe they are old 1.1 cabels). But I know I have a few cables around that dont charge my phone and they also will not work with my portable external usb hard drive because they wont provide enough power for it. But they work just fine with my digital camera.

I´ve read somewhere that disabling USB charging is better for the battery life, so I have it disabled.

You've tried different USB ports, but were they on the different computers?

so i've tried different cables, different ports and 2 different PC's and 2 different laptops.
I know its not the cable i'm currently using because i plugged it into one of those A/C to USB adapters and charged fine.
I'm starting to think its my batter,
If you have tbattery installed, do u get values for all the boxes?
All mine except 3 or 4 are 0 :/

Well, you are not the only one having this problem. Mine is brand new. I started setting it up last night and had it hooked to the computer via usb. I installed a few .cabs such as google maps, myphone, and a few tweaks such as tether, disable sent notification, enable all camera modes, and manila start menu unlocker. While it was connected it said it was charging. When I went to bed I turned it off and connected it to another usb cable on another computer which is an a/c hub. I went to turn it on this morning and thought it was strange it was not fully charged. I continued to set it up a bit and take it for a spin. After a while I turned it off again and hooked it to the usb a/c charger again. I just tried turning it on and nothing was happening. I connected it to the usb again and it finally turned on, but I checked the battery level and it was at 0% and turned off. I have it connected to the a/c charger and giving it a little bit to see what will happen. One thing that seems strange is that the battery discharged more while it was off and attached to the usb a/c hub during the afternoon causing it to refuse to turn on at all. Any thoughts?

fone_fanatic said:
so i've tried different cables, different ports and 2 different PC's and 2 different laptops.
I know its not the cable i'm currently using because i plugged it into one of those A/C to USB adapters and charged fine.
I'm starting to think its my batter,
If you have tbattery installed, do u get values for all the boxes?
All mine except 3 or 4 are 0 :/
Click to expand...
Click to collapse
I think the odds are pretty good it's your battery. The orange light means power is going through the charging circuit, so you obviously have your settings correct.
I'm guessing you're in Austin or near? If you want to try popping my battery in it for a few minutes and see if it charges fine then, PM me and we can set something up.

the same thing is happening with mine. Sometimes it will charge, sometimes it wont. weird thing is that it only started doing this a few days ago... i know nothing has changed ROM wise, so only things i can think now is maybe the actual USB connector on the phone or the battery, but since I am getting a charge via wall chargers im not sure what to think lol

Just an update.
If i have the USB cable plugged in (and car charger to which doesn't charge as well ) after 15 min or so a warning appears saying that the current is too low to charge the device. Either closed unused apps or switch to a/c power.
I've ordered a 1800mah Mugen Power Battery. Gonna see if it resolves the issue, if it does then i'm gonna call at&t and see if they'll swap my battery for me.

I have found as have others here after reading some posts that if the phone is almost dead or battery is very low then it will not charge via the USB anymore. The orange light goes on and it says that its charging but the charging circuit seems to be protecting the phone and not letting the battery charge.
The only solution I have found, and it has only happened twice so far is to plug it into a wall charger and fully charge the battery. It will then charge via USB again and all is good. I normally only charge my phone with usb while connected to Activesync but once in a while you seem to need to top it up with a wall charger.
It is also highly recomended not to run Lithium Ion batteries right out.

How do you know it is not charging?
There is a difference in the wiring from a wall charger and a USB charger. There is a signal line in the wall charger telling it to charge at near 1000ma. In the USB cable that line tells it to limit the charge current to 500ma. That is the limit for current that you should pull from a USB port. If you are using the unit heavily, you may actually need more then the 500ma., those running the battery down possibly.
If the unit is idle, it will still take much longer to charger from USB then off of a wall charger.

worwig said:
How do you know it is not charging?
There is a difference in the wiring from a wall charger and a USB charger. There is a signal line in the wall charger telling it to charge at near 1000ma. In the USB cable that line tells it to limit the charge current to 500ma. That is the limit for current that you should pull from a USB port. If you are using the unit heavily, you may actually need more then the 500ma., those running the battery down possibly.
If the unit is idle, it will still take much longer to charger from USB then off of a wall charger.
Click to expand...
Click to collapse
If you are asking me, I know it was not charging because I also had the "not enough power to charge message" and the phone went from about 15% when I plugged it in to stone cold dead by the morning. The whole time it was pluged into a computer I have used repeatedly to charge it with. I then put it on a AC charger and it went to full charger in about an hour and a half or so.

Phone charging and Satnav...is this normal?

Just been on a long run and used the satnav ( google ), and the whole time it was plugged into the cigarette lighter charger.
Despite this, the battery level was running down
Is this normal - that the battery drain using the satnav/gps is greater than the charging rate?

I used mine yesterday for about a 1/2 hr journey, was not plugged in, but batterey was down to about 30%, also seemd to use about 20mb for 15 miles, so watch your usage.

J-Zeus said:
Just been on a long run and used the satnav ( google ), and the whole time it was plugged into the cigarette lighter charger.
Despite this, the battery level was running down
Is this normal - that the battery drain using the satnav/gps is greater than the charging rate?
Click to expand...
Click to collapse
Its been discussed already, your charger is not powerful enough to charge it when using satnav, so the end result is that your charger is just slowing down the discharge. Happens when you are using 3rd party accessories.

Ah - That makes sense -- where can I get a decent one - at a decent price

I'm using the factory supplied lead and still get the same, also used to be a problem with my Touch Diamond 2 WinMo Phone, was hoping Desire would be better and it is... just... If I make sure it is fully charged before I set off I can do about 3 hours with it plugged in before it goes flat, I just keep switching it off while I know where I'm going and only switching it on when I don't! That way you can make it last until it is needed.
Another thing to check is that it is kept cool enough to charge, again, in common with my older HTC winmo phone, the Desire gets very hot while being used for GPS and this can be worse if it is in sunlight on your windscreen, sometimes this can stop it charging at all, (you can tell its in this state because the indicator light blinks alternately orange and green) I angle a vent so its blowing cold air on the phone and that seems to do the trick.
Weird thing with the Desire is that for me it shows the green charge light and battery full indicator right up till it is nearly dead... rather than showing that it is draining
I've also noticed with the Desire that even If I'm just browsing the web it drains quicker than it can charge, even using mains charger, I often get a message "the current is insufficient, please connect to AC" or something like that (when it is already plugged in)
I don't think the in car charger you use would make a big difference, the current/voltage for your cigarette lighter socket is limited by the vehicle electrics (I know mine is fused at 15 amps)
Pauly

You need a charger which supplies 1A. Most 12v cigarette lighter chargers only supply 500mA
I use this one, and plug the USB cable into the "quick charge 1A" socket
http://www.argos.co.uk/static/Product/partNumber/5140927/Trail/searchtext>BELKIN+CHARGER.htm

Are you using Bruts worldwide maps mod? I just installed it. I ran it for literally only 5 minutes, but my phone got really hot and the battery monitor shows the app used 10% of the charge (the phone has been unplugged for 24 hours). I have a strong suspicion that this app is faulty.
-------------------------------------
Sent via the XDA Tapatalk App

This has been discussed and solved here http://forum.xda-developers.com/showthread.php?t=670702
Basically most usb car chargers (even 1a rated ones) are recognised by your phone as a data connection and to protet delicate computer usb circuits will only draw 500mAh where your phone requires 950mAh.
An easy mod of either the charger or a data cable will solve the problem. Your charger MUST be able to supply up to 1a.

zzleezz said:
This has been discussed and solved here http://forum.xda-developers.com/showthread.php?t=670702
Basically most usb car chargers (even 1a rated ones) are recognised by your phone as a data connection and to protet delicate computer usb circuits will only draw 500mAh where your phone requires 950mAh.
An easy mod of either the charger or a data cable will solve the problem. Your charger MUST be able to supply up to 1a.
Click to expand...
Click to collapse
Thats why I use the Belkin one, it detects it as a charger only and charges at full rate when plugged into the 1A socket.

Battery does not charge when the phone is in use!

Hi guys
Im having a weird problem with the battery. It seems battery doesnt charge when im using the phone although it says and shows it charging! It just stays at the same battery percentage it doesnt charge or drain! When i turn off the screen it charges the battery just fine. I called o2 UK where i bought the phone, the rep said when i use the phone it consumes more power than it gets. Can this be true?! Do you think its just a software bug or defective hardware or defective battery?
Sent from my Galaxy Nexus

This is true if you're charging from the USB on your computer. USB ports only provide 500mA. The phone seems to use more than this if you are actively using it. I recommend using a wall plug that provides at last 1 Amp (1000ma) to effectively charge the phone.

How about car chargers? Same thing happens when its charging with the car charger..
Sent from my Galaxy Nexus

If I'm not mistaken, any car charger, whether it's rated at .5A, 1A, or 2.1A is only going to provide .5A to your phone using a typical USB cable. The USB cable that came with your phone has +/- lines for power as well as 2 data lines. If you pickup a "charging only USB cable" it has the data lines shorted so that only the power lines are functional. This type of cable would allow you to take advantage of the higher current 1A and 2.1A chargers - I think anyway. I'm still new to Nexus so I haven't confirmed that, but that's the way it worked on my old phone. I did read somewhere that even with a charging only cable someone wasn't able to pull 1A from their car charger so I don't know if that was a unique issue or if the Nexus doesn't behave the same way. My understanding is the amount of current pulled from the charger is dependent on the charger AND the phone. Using a special charging cable tricks the phone into thinking it's on A/C I guess.

Highest Charging Current for One X

Hi all:
I just did a test on the maximum charging current of the One X using current measurement equipment, and it shows that the One X does not draw above 460mA of current while charging.
With this value, i suspect that the One X limits max charging current at 500mA, which means 3 things:
1) Using any previous generation USB charger (750mA or 850mA or 1A) is good enough. Attempting to use the iPad's charger (rated at 2A) WILL NOT get you faster charging time.
2) When using battery draining applications, the charging current may not be enough for you to both CHARGE and USE the Phone. Thus it might be a better idea to give your One X some dedicated charging time.
3) Some computer USB ports may specify 500mA of output current, but there are many times the available current is less than that. On my USB port, the charging current is only about 300mA at times. So it is better to use a dedicated charger if you have it available. Having that said, however, it is still ok to charge the One X with a USB port at 300mA, just that charging will take longer.
That's all I have to report. Useful information for all.

limestone said:
Useful information for all.
Click to expand...
Click to collapse
Useful indeed. Thanks
Sent from my HTC Vivid using XDA app

I've had mine charge at 780mAh+ before. 1amp HTC charger. Charge rate slows down at the last 20-30% or so. So from 70%-100% battery, charge rates normally slow to about 450mAh.

limestone said:
Hi all:
1) Using any previous generation USB charger (750mA or 850mA or 1A) is good enough. Attempting to use the iPad's charger (rated at 2A) WILL NOT get you faster charging time.
Useful information for all.
Click to expand...
Click to collapse
thanks a lot, i can confirm the statement above because my stock charger is broken and i'm using the ipad's one.
bye

i tried to use the charger for htc chacha and hd2..
both does not work.. red light will light up but after a while it will go off and the phone does not charge..

Charging my HOX while the phones working hard eventually (after say, 5 mins), causes the charge LED to flash green/red. I've had this twice now, once while playing a 720P HD film, and once when playing Glowball.
Both times the phone was very hot, so i'm not sure if the LED thing was to indicate that the battery was too hot to charge, or that the charger could not supply enough power to charge and power the phone at the same time.

fi3ry_icy said:
i tried to use the charger for htc chacha and hd2..
both does not work.. red light will light up but after a while it will go off and the phone does not charge..
Click to expand...
Click to collapse
I'm using my HD2 charger at work every day. It charges at about 400/500mA.
Original charger gives me 650/750mA (lowers at the end)

chaps said:
Charging my HOX while the phones working hard eventually (after say, 5 mins), causes the charge LED to flash green/red. I've had this twice now, once while playing a 720P HD film, and once when playing Glowball.
Both times the phone was very hot, so i'm not sure if the LED thing was to indicate that the battery was too hot to charge, or that the charger could not supply enough power to charge and power the phone at the same time.
Click to expand...
Click to collapse
If the charger cannot cope with the discharge from the game, a pop up message actually appears. If it's blinking means it's too hot. Try not to do anything intensive the last 20-30% remaining (meaning at 70-100% battery).

Nice info thanks
Sent from my HTC One X using XDA

fi3ry_icy said:
i tried to use the charger for htc chacha and hd2..
both does not work.. red light will light up but after a while it will go off and the phone does not charge..
Click to expand...
Click to collapse
Same here... I am using the Atrix 4G (US) charger, it does not charge the phone. The charger gives output of 850mA. It does charge when plugged into the laptop, but I think it will take very long that way.
*edit for posterity*
after a while (I did it when battery had charged to 20%), I could connect the Moto US charger, and it would show as "AC". It would not want to charge through it when the battery was really low (2%), but it would charge via USB in that case. Weird behavior, IMO.

USB limited to 500. AC limited to 1A.
Sent from my HTC One X using xda premium

If you want maximum speed of charging (AC charging) you need:
1A charger with shorted D+ and D- pins (eg, original HTC charger).
iPad charger probably doesn't have these pins shorted, so in this case phone will see it as USB charging (you can check it in settings->battery) and will limit charging current to 500mA. Also lot of aftermarket car chargers will work only in USB mode despite they are able to supply 1A.
Here you can find some info on USB Charging Ports (shorted D+- pins):
http://en.wikipedia.org/wiki/Universal_Serial_Bus#Charging_ports_and_accessory_charging_adapters

When charger is "USB", it will not draw more than 500mA from the charger, and usually it will not charge at all (because the current draw with screen on is higher than 500mA).
When charger is AC, it seems to draw 1000mA - but this is still too low to charge while phone is doing anything, as it will draw 700mA and charge ~250mA top.
I hope this can be tuned in kernel, because it sucks, I also hope that power source can be AC (and not battery - look in dmesg when charger is connected), because battery gets too hot when under load...

colin_ktp said:
If you want maximum speed of charging (AC charging) you need:
1A charger with shorted D+ and D- pins (eg, original HTC charger).
iPad charger probably doesn't have these pins shorted, so in this case phone will see it as USB charging (you can check it in settings->battery) and will limit charging current to 500mA. Also lot of aftermarket car chargers will work only in USB mode despite they are able to supply 1A.
Here you can find some info on USB Charging Ports (shorted D+- pins):
http://en.wikipedia.org/wiki/Universal_Serial_Bus#Charging_ports_and_accessory_charging_adapters
Click to expand...
Click to collapse
Can you post a potential list of car charger which are working at 1mA according to you?

I've only tested few devices:
Extrememac external battery for iPhone/iPad (max 2A) had pins not shorted - USB charging mode on One X (500mA).
Some cheap car adapters - max 1A (according to spec) - USB charging mode on One X.
To fox this problem you should prepare a USB extension cable or micro-usb cable with shorted D+ and D- pins and it should be recognized as AC adapter. I think that also some old HTC phone chargers might come with shorted pins in cable already, but don't know which...

What about the official HTC car charger?

MickyMax said:
What about the official HTC car charger?
Click to expand...
Click to collapse
Yes, that one will charge at the full rate.
There is no list of known good chargers - it's down to luck or a recommendation from someone who found one. You can be sure that any charger advertised as "iPhone, iPad or iPod" compatible will NOT charge your One X at the full rate.
I found one recently in a local petrol station shop. It was £5. I took it apart to have a look and the D+ and D- pins are correctly connected together (via a low value resistor) so it charges at the full rate.
So, I might suggest you look for the cheapest Chinese car charger you can.

USB charging not OK inside a car
zvieratko said:
When charger is "USB", it will not draw more than 500mA from the charger, and usually it will not charge at all (because the current draw with screen on is higher than 500mA).
When charger is AC, it seems to draw 1000mA - but this is still too low to charge while phone is doing anything, as it will draw 700mA and charge ~250mA top.
I hope this can be tuned in kernel, because it sucks, I also hope that power source can be AC (and not battery - look in dmesg when charger is connected), because battery gets too hot when under load...
Click to expand...
Click to collapse
Bingo. I also noticed that when I have the screen on at 100% brightness, GPS and Bluetooth on, i.e. in the car, the USB charger cannot even keep up with the battery drain.
On top of that, the battery gets really hot.
I did not have any of these issues with my SGS2, and frankly, I think it's very disappointing. One should at least be able to stay on the same battery level while doing nothing too fancy and on USB inside a car.

A380 said:
Bingo. I also noticed that when I have the screen on at 100% brightness, GPS and Bluetooth on, i.e. in the car, the USB charger cannot even keep up with the battery drain.
On top of that, the battery gets really hot.
I did not have any of these issues with my SGS2, and frankly, I think it's very disappointing. One should at least be able to stay on the same battery level while doing nothing too fancy and on USB inside a car.
Click to expand...
Click to collapse
There are a lot of factors in the charging current. When you charge, the battery will heat up during the process, especially towards the end of the charging cycle. If you are using your phone at the same time and cause even more heat and charging may slow down to prevent overheating. Also, as mentioned prior, charging slows down as capacity is reached. 100% brightness, GPS, and Bluetooth all on has always walked the fine line of just barely keeping up on my past phones on a 500 mA USB charger. On top of that, this phone is a lot more powerful than an SGS2 and the T3 and big screen produce more heat which may be slowing your charging more.
The problem is a lot of cheap chargers that the phone thinks are USB chargers, not AC chargers, thus causing them to only charge at 500 mA. If you have a proper charger, or a properly modified charger, you should get more like 1A, assuming conditions are right.
In the past I've used Battery Monitor Widget from the Play store to show my charging current on a widget, as well as track and graph battery use, charging current, temperature, etc. Might want to give it a try if you're more interested in charging details.

Im using my htc desire charger and cable (the one that splits in two). It works fine for me but it does take a while to get a full charge. Should i use the charger and cable that came with the phone?

I can only use the Samsung charger?

Recently I've noticed that my Gnex battery will LOOSE charge when plugged into any power source that isn't the Samsung charger. Weird right? If i plug it into my laptop, car charger, an LG wall charger the battery will drain. It has happened multiple times where i've hit 15% battery life and plugged it into my laptop or car charger and it will loose a 1% about every 2-3 minutes.
I've switched roms with no luck. What is going on?

Its not uncommon for this to happen from a laptop port - especially if the phone is being used while plugged in. The USB output on laptops is likely not very high.
Check the amperage of the alternative chargers you are using. If its too low, they won't be able to keep up. Make sure its the same as what the stock Samsung one puts out. Can't recall its exact specs off the top of my head...

Laptop and car charger are 500mah or less. Your phone is using battery faster that it's recharging. Nothing odd about that.

charger
I'm charging on my laptop with a cable of blackberry and no loss there. Charging with at the wall I'm using only samsung utilities so I can't help you out there..
Despite that I don't understand what that has anything to do with rom's?