Can anyone recommend me a good car holder for the phone? I want to get a sturdy good quality one, because I want to use it as a GPS navigation
Hey, I'm using Windowseat Mobile car dock (without the hands-free part). It's really great, the mount has an adjustable height supporting multiple devices, it's sturdy, looks and feels good. Here is the link
http://store.griffintechnology.com/iphone/windowseat-mobile-handsfree-car-kit
woah a bit too expensive for my liking.
Any other recommendations?
http://www.ebay.com/itm/270819200517?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
I got this one for my X10... Cheap, nice looking, working...when I have order it I thought it is a crap, but what you need from a card holder??? It fits, holding good and don't fall of the glass... Nice.
What does everyone think of this?
http://www.amazon.co.uk/FoneM8-Omni...en-Blackberry/dp/B005XYJDY2/ref=cm_cr_pr_pb_t
I think it is not good...because it is not enough flexible to choose a good position and the phone can fall out of it! I would recomend this one... The car charger is good and powerfull, not bad holder, as I said got it for X10... Some additional case.
http://www.ebay.com/itm/Car-Mount-H...936243?pt=PDA_Accessories&hash=item3f145331f3
Same at amazon
http://www.amazon.co.uk/SUPERSTORE-...?s=electronics&ie=UTF8&qid=1331747821&sr=1-10
http://www.tetrax.com/us/
i use this mount for my arc.
obostore.com/fit-to-all-car-motor-vehicle-holder-mount-p-2506-c-126.html
i order this one holder is it good?
http://www.ebay.com/itm/Universal-C...288437?pt=PDA_Accessories&hash=item2c67c16475
I'm using some el cheapo generic phone mount, works just fine. :laugh:
Related
I know there a few threads about windshield mounts but none of them have what I'm looking for. I am looking for a windshield mount for my 2000 Ram 1500. I want it to mount on the BOTTOM on the windshield and come to the edge of the dash so it will need to be fairly long. I switch between the Seidio Innocase II surface and the Seidio 3500mah extended battery so I need something that will accommodate both of those. I also need it to switch between portrait and landscape. The Kensington windshield mount for the Iphone looks like it would be great but it doesn't look like it will allow me to use my extended battery.
What have you guys found that might work for what I need?
ive been using this...
Scosche IUHW7 Windshield Vent Mount Kit.
its inexpensive it sitcks... it turns and fits all kinds of stuff
I think I got it for 12 bucks at walmart
bacidath said:
ive been using this...
Scosche IUHW7 Windshield Vent Mount Kit.
its inexpensive it sitcks... it turns and fits all kinds of stuff
Click to expand...
Click to collapse
I might have to see if my local walmart has that. Thanks.
http://www.seidioonline.com/product-p/ck17hev4c04.htm
it is not long but with a little modification it will work.
it also holds thee innocaseII and the extended battery one.
will car dock the phone
Ram Mounts are good in trucks
http://www.ram-mount.com/
Mountek MT5000
I bought this after finding a thread about it on another forum. Best accessory ever. Extremely quick and easy to install, rotates portrait/landscape ... can't complain about anything. It uses your CD slot - you just put it in the opening and clamp it down.
It's actually started to become a problem because I'm constantly distracted while driving by my cellphone now. It's just right there up in my face, gorgeous and begging to be played with.
Can't post the link since I'm new here ... but you can Google it easily.
I like the Clingo mount so much, I am going to mod the Sedio Active Innocase I have to make it work with it (smooth.velvty doesn't stick to Clingo).
sanyi83 said:
Ram Mounts are good in trucks
http://www.ram-mount.com/
Click to expand...
Click to collapse
I've used Ram Mounts in my Jeep, good stuff!
Sent from my Desire HD using XDA App
I've got a cheap Arkon universal mount I use in my car. Works great with my ballistics case or naked.
Dunno how long it is but I have am ikd z car and its mounted to the bottom of my windshield and comes to the dash edge. Probably 6in or more. It was tricky too cause my car has a high rake angle and I wanted it mounted so it wouldn't show Tue mount at all in videos. It does block half the camera but it clamps hard enough that you can scoot it up and get the camera free.
Sent from my (insert daily ROM name here) Evo 4g
When in its case, mine fits in my Garmin windshield mount
Sent from my PC36100 using XDA App
Why not just get the seidio innotraveler? It will fit both the extended battery and innocase power their website. I have it and love it, it actually extends pretty far.
Sent from my hand with XDA Premium installed
Because the seidio one is $50! Thats crazy for a windshield mount. I found one at bestbuy yesterday its by rocketfish and made for the iphone but it works with our phone to. It doesn't come to the edge of the dash but it will work.
I'm looking for a good car mount for Arc.
Can anyone recommend or give a link?
I tried ebay but you know any better ones?
For sure Carcomm and Brodit are the best. I asked them when they would be available. No clear answer they are working on the development.
BR
these are actually better than they look
http://cgi.ebay.co.uk/ws/eBayISAPI....94602&ssPageName=STRK:MEWNX:IT#ht_1628wt_1139
the sides are in two halves and slide apart meaning you can configure it how you like. It has foldaway bottom rests and turns 360 so you can have the phone landscape or portrait. Its actually one of the best ive had in a few years and most certainly the cheapest
Hi,
a good car mount for Arc maybe is Tetrax: (www . tetrax . com)
The problem is that you must paste a metal circle on the backcover
But is the best solution because you can touch and rotate the "Arc" in every position.
I recently thought about
http://www.amazon.de/dp/B002OLL9BC/...eative=6742&camp=1638&creativeASIN=B002OLL9BC
or
http://www.amazon.de/q1-Autohalteru...=sr_1_1?s=ce-de&ie=UTF8&qid=1304165356&sr=1-1
And I wondered if one of those would be any good...
I recently got this one:
cgi.ebay.com/Windscreen-Car-Mount-Sony-Ericsson-Xperia-Arc-/130502621883?pt=UK_Holders_Mounts&hash=item1e628ffabb
I must say it fits my Arc perfetly!
silasdm said:
I recently got this one:
cgi.ebay.com/Windscreen-Car-Mount-Sony-Ericsson-Xperia-Arc-/130502621883?pt=UK_Holders_Mounts&hash=item1e628ffabb
I must say it fits my Arc perfetly!
Click to expand...
Click to collapse
Can you tell me if a a skin cover is on the phone will it still fit on the Holders?
Brodit mount
According to their site, it will be available in 5 days.
pato_bato said:
Can you tell me if a a skin cover is on the phone will it still fit on the Holders?
Click to expand...
Click to collapse
Can't tell, if it's thin enough... I'm waiting for a skin cover, and I will report if it fits when I get it.
I use this one and is very good compared to the price
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200591474760&ssPageName=STRK:MEWNX:IT
statsminister said:
I use this one and is very good compared to the price
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200591474760&ssPageName=STRK:MEWNX:IT
Click to expand...
Click to collapse
I like that too.. but I want to know if the phone still fit if you have a skin case on the phone. Because the mount looks like a perfect fit on the phone it self.
I got one of these for my HTC Touch HD and it works just as well for my Arc. The width is adjustable to it can clamp the phone snuggly. And it has additional legs as support that rest against the dashboard. Worked great until I got my new company car. It has stupid modern weird shaped vents that it doesn't hook onto. Not without getting in the way of the indicator stalk anyway.
Should work fine for most cars with normal air vents though.
http://www.mobilefun.co.uk/universal-phone-vent-holder-p27265.htm
Cheers
Dazza
Brodit just released a passive and active support (http://www.brodit.com/?lang=E). See links at The bottom of brodit webpage.
pato_bato said:
I like that too.. but I want to know if the phone still fit if you have a skin case on the phone. Because the mount looks like a perfect fit on the phone it self.
Click to expand...
Click to collapse
The mount is some type of hard rubber, so it is possible to let it hold an arc with a skin case. It is usable, but can't say it's a perfect fit ;-)
Sent from my LT15i using XDA App
Brodit mounts
I've just checked Holder and Mounts and Brodit mounts are listed and seems to be available to buy in the UK.
The Brodit ones are good but you need first the clip for you car only and then buy the holder for the phone.
I used mostly the pasive holder and if you put in landscape and you take a sharp turn your phone can be flying (HTC diamond2). With my Nokia E65 back then the passive holder seem to be very fit so I had to put in hard and you could get some scratches on the sides ...
I think the active holder seems a better fit and keep your phone safe in landscape, but dont know for sure it seems better attached but also more expensive.
Just my two cents but overall I think Brodit doing a good job but when you buying new phones all the time it can get expensive too if you have to replace the holder everytime.
Now that I have a snap on case for the arc
http://forum.xda-developers.com/showpost.php?p=13764860&postcount=71
Challenge now is will this car mount fit with this snap on case before i place the order. http://cgi.ebay.com/ws/eBayISAPI.dl...ageName=STRK:MEWNX:IT&clk_rvr_id=232032065754
Anyone who has this car mount [link above] can you show a pic with a silicon case or any case on the phone with the car mount? thanks.
I got the active one from Brodit, and I can tell you, that it is excellent
Unfortunately Brodit mounts are not suitable for SE Arc with case of any sort.
I use this one by Nokia. Fits PERFECTLY, SECURELY and best part of it is that it is tiny and refined compared to the rest of the eBay ones which is huge and ugly
Been using it since Nokia E71, E72, HTC Legend and surprisingly, it fits the Arc the best
http://bit.ly/jbBWKJ
By pure chance I found out that my SIII with its slimline cover fitted works perfectly in my Garmin Nuvi 205 dash mount.
Secure and easy to mount, almost as if it was made for the S3.
The Garmin Part Number
Item 010-10936-00 Suction cup with bracket (Nuvi 2xx series)
Cost is around $10 - %15
Cover is a Cygnet BlackFrost Matte slim case (around $20)
I love finding a really good cost effective solution for my toys!!
Video Clip. Please excuse poor sound quality, had to dig out my old Olympus compact to make this,
Thanks, looking forward to the video.
good to know since Garmin has quality mounts.
Does it actually clip in? Is it firm?
If you remove the case, hows the fit?
Fits snugly, clips into the mount as if it was made for it,
Doesn't work without the cover though, phone is just to small,
Would be possible rather easily I might add to put some shrink tubing on the arms of the mount and build it up a little to hold the phone naked!
I wonder if it would fit with a tpu case. Your case seems pretty slim
ZaJules said:
By pure chance I found out that my SIII with its slimline cover fitted works perfectly in my Garmin Nuvi 205 dash mount.
Secure and easy to mount, almost as if it was made for the S3.
The Garmin Part Number
Item 010-10936-00 Suction cup with bracket (Nuvi 2xx series)
Cost is around $10 - %15
Cover is a Cygnet BlackFrost Matte slim case (around $20)
I love finding a really good cost effective solution for my toys!!
Click to expand...
Click to collapse
Thanks for the find. Do you think it would be able to fit the S3 with an Otterbox Commuter case on? My phone's approximately 7.7mm wide with the case on.
Cheers
Might fit but it would be tight, the rounded edges of the Cygnett case allows it to clip into the holder the otter box might be to square
Sent from my ASUS Transformer Pad TF300TG using Tapatalk 2
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
kl25 said:
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
Click to expand...
Click to collapse
You should get a replacement one...They are super cheap on eBay. I have one that is over 7 years old (*back when standalone GPS units were +$300!) and it still works great.
kl25 said:
my garmin gps always falls off from the windshield now..the suction cup doesn't hold..don't know how i'd feel putting my phone there..
am i suppose to wash it with soap or something to make it work again?
Click to expand...
Click to collapse
I fix that with alcohol. But then I fix everything with alcohol.
universal mount
I got this car mount from amazon.com
Search for Kropsson Aero universal mount.
the design of the mount was a great plus.
Feature wise, defiantly recommend.
proud a-clown said:
I fix that with alcohol. But then I fix everything with alcohol.
Click to expand...
Click to collapse
:laugh::good:
couldn't have said it better myself!!!!
I can confirm this mount works great with the rock quicksand case. Easy to put in and take out and holds rock solid. Before the case showed up I had used a couple pieces of heat shrink tubing held on with electrical tape and it worked awesome with the naked galaxy s3.
I like this style of mount because you can position the phone with it gripping the middle, top or bottom to fine tune where the screen is in relation to your windshield.
I went with this one though, instead of one of the $5 options: (replace spaces with ., I don't have enough posts to post links) www amazon com/gp/product/B0042PJ8NY/ref=oh_details_o00_s00_i00[/url]
It's the actual oem garmin mount instead of a knockoff, and judging by the reviews the difference is the mount that holds the ball is made of metal, so it won't break. It came with one of the 3m PE Foam adhesive backed discs for mounting to the dashboard as well. Highly recommended.
I just tried it. PERFECT fit with my diztronic TPU case. Thanks OP!
I had a nice set up for my Lg G2X, a pouch holder that attached to the handlebars of my Sportster with a rubber loop. I took a hard rubber case and modified it to the holder. Worked well.
But I cannot find a suitable rubber S3 phone cover to do the same thing with. None are hard enough for me to be comfortable with. I'm afraid the phone will slip out. And I don't really like the pouch as originally designed on this holder. Want to actually touch the screen.
There is a steel device holder available with channels on top and bottom that looks real secure, but not real low key.
Anyone have any suggestions for a good phone holder?
Love listening to Pink Floyd on my bike LOL. When I get a call, it mutes and I have to push the play button which now involves taking it out of my pocket.
FYI I use the Scala communicators which are awesome.
Thanks in advance for your input.
Ram Mounts
Go to ram-mounts.com. They will mount anything to anything. Car, boat, truck, airplane, motorcycle, bicycle. Makes do difference. Plus, their stuff will not shake loose. They probably even do saddles.
Motorcycle page:
http://www.rammount.com/Products/MotorcycleMounts/tabid/128/Default.aspx#/wizard
schneid said:
Go to ram-mounts.com. They will mount anything to anything. Car, boat, truck, airplane, motorcycle, bicycle. Makes do difference. Plus, their stuff will not shake loose. They probably even do saddles.
Motorcycle page:
http://www.rammount.com/Products/MotorcycleMounts/tabid/128/Default.aspx#/wizard
Click to expand...
Click to collapse
Thanks for the link! At $104.00, that's a bit pricey. Looks like a pretty good system though.
rokform rokbed has a case that doubles as a mount. also a little bit pricey but check it out, kinda cool
http://www.rokform.com/cart/Galaxy-S3-Cases/
http://www.rokform.com/cart/v3-Bikemount.html
This is what I use on my bike:
RAM part number - RAM-B-149Z-UN4U
No problems at high speeds and works great with my Sena SMH-10. I have an Otterbox commuter and with the fingers adjusted all the way out, it's a tight fit.
Can anyone recommend a good car mount?
I just bought some cheesy magnetic thing from Amazon. Will be returning ASAP. Ideally, I think I'm looking for something that can clip into either the air vents or on the dash of my car. I realized there probably aren't many pixel specific accessories made yet, but maybe someone has had good success with a different model for an earlier phone?
Anyway just wondering what you all were planning on using.
I've been using a good magnetic mount for the CD slot in my car since the Nexus 5 days. I like the Koomus brand of them from Amazon.
Sent from my Pixel 2 XL using Tapatalk
I personally been using ProClip for a while. With my Nexus 6 I have a universal one since I have a thin case it slips in. Mounts are made per vehicle too.
https://www.proclipusa.com/category/google-pixel-2
Sent from my Nexus 6 using Tapatalk
I've had the third generation iOttie car mount for about a year, and it is excellent. It doesn't have a vent clip, but its suction cup mount is very sturdy. It even comes with a little pad you can use if your dash is textured.
I second the ProClip. You can get a custom mount for your vehicle, and select a separate holder. I've got a custom mount and a universal holder that can be adjusted if you switch phones.
I second the recommendations for iOttie mounts. I bought their wireless charging one back when I got my Galaxy S6, but I still use it with my Pixels because it is incredibly convenient to secure and remove the device. Excellent quality, usability, and adjustability, well worth the purchase.
coolsilver said:
I personally been using ProClip for a while. With my Nexus 6 I have a universal one since I have a thin case it slips in. Mounts are made per vehicle too.
https://www.proclipusa.com/category/google-pixel-2
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
Looks like a solid product! I have an '09 Kia Spectra and the dash doesn't look like an easy place to put a phone mount. I checked out their custom mount for my car and the only drawback I can see is it completely covers a vent (for a/c) which may or may not be an issues, I won't know until mounted but.. Any experience with that for you?
Yea on my prior vehicle I had it cover the vent. It was out far enough so it still put out air but it wasn't really directional as far as flow as before. Center ones I didn't care as much about being pointed at me to keep cool. It was a solid bracket though
coolsilver said:
Yea on my prior vehicle I had it cover the vent. It was out far enough so it still put out air but it wasn't really directional as far as flow as before. Center ones I didn't care as much about being pointed at me to keep cool. It was a solid bracket though
Click to expand...
Click to collapse
Thanks! They do look solid ...
I have an existing car mount for my S7 before I got the XL, it holds the phone in landscape and squeezes the sides. Little concerned that this may not be good for the squeeze sensors. Anyone think it could affect the sensors over time?
I have this one since May 2016 no issues and easy off and on for various phones..I have vent but they make cd slot and I think window too
iOttie
https://www.amazon.com/gp/product/B017HME9DC/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
Sent using Tapatalk
Haven't used these myself, but they look pretty sweet...https://www.amazon.com/dp/B01DCSIRG0/ref=cm_sw_r_cp_awdb_KmO7zbB7T3BNE
Anybody used this one before?
Cowbell_Guy said:
Can anyone recommend a good car mount?
I just bought some cheesy magnetic thing from Amazon. Will be returning ASAP. Ideally, I think I'm looking for something that can clip into either the air vents or on the dash of my car. I realized there probably aren't many pixel specific accessories made yet, but maybe someone has had good success with a different model for an earlier phone?
Anyway just wondering what you all were planning on using.
Click to expand...
Click to collapse
Another vote for Proclip's mounting solution. The universal large holder works fine with my Pixel 2 XL with a (Caseology Parallax) case. It's pricey but it works beautifully.
I just ordered the IOAuto magnet holder to use with Proclip's mounting bracket. I'm tired of sliding my phone into the holder. 1st world problems, I know.
Sent from my Pixel 2 XL using Tapatalk
morbidhippy said:
I just ordered the iOttie magnet holder to use with Proclip's mounting bracket. I'm tired of sliding my phone into the holder.
Click to expand...
Click to collapse
How does that work exactly? Which iOttie did you buy, and how does it work with the ProClip bracket?
dberthia said:
How does that work exactly? Which iOttie did you buy, and how does it work with the ProClip bracket?
Click to expand...
Click to collapse
Oops, I meant IOAuto, not iOttie.
https://www.proclipusa.com/product/...xkJK2QwbcDyiiZdeiDsdvqZtMoM3Vg84aAjDOEALw_wcB
I bought the IOAuto Pro. It attaches to the vehicle mount that I purchased previously from Proclip. It comes with small circular metal disks that should be attached to your phone.
I hate the thought of using adhesive to stick anything on my phone so I'm going to try and place the disk between the phone and my TPU case. In think the magnet will still work fine.
Check out YouTube. I've seen a couple of videos of others installing it.
Sent from my Pixel 2 XL using Tapatalk
I like this simple magnetic holder:
Techmatte MagGrip Orbit Universal Air Vent Magnetic Car Mount Holder
It requires a thin metal plate which works fine if you use a TPU case or other case that's not too thick on the back; this way, it doesn't require any permanent application. I bought 3 for family members, and a friend got one after seeing mine. It's easy to mount, secure, very simple in design - it uses a steel ball that mounts to an air vent, and a magnetic piece that connects to the ball, giving easy adjustment in all directions, or complete removal. This magnetic piece connects to the phone's steel plate. My wife has an iphone 6P which works well; I have a nexus 5X.
coolsilver said:
I personally been using ProClip for a while. With my Nexus 6 I have a universal one since I have a thin case it slips in. Mounts are made per vehicle too.
https://www.proclipusa.com/category/google-pixel-2
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
Adding a :good: for the ProClip. Mine just came yesterday and works perfect.
morbidhippy said:
I hate the thought of using adhesive to stick anything on my phone so I'm going to try and place the disk between the phone and my TPU case. In think the magnet will still work fine.
Click to expand...
Click to collapse
I'm curious to see if that works out for you. I'm intrigued, but it seems like $50 is a bit steep for that mount. If it works well for you with a case, I may consider it though.
I know my solution isn't going to be for everyone, but it works well for my needs. I have a hybrid Proclip/Ram Mount solution. Proclip for the center dash mount, then Ram Mounts for the rest (ball, short arm, and X Grip holder). It's more involved than the common solutions, but it puts my phone right whereIi want it and it's rock solid--which is important for those track days.
As mentioned upthread, this does partially block the vent, but on my Mustang not by too much, and the passenger still gets air flow when it's directed their way. A bonus is the phone stays nice & cool when staying on playing podcasts while commuting, or running the telemetry apps while on track.
I can strongly recommend this one. They're a little pricey but I have them in my truck, car, 4-wheeler and mountain bike. Just the spring clips are strong and when you add the rubber sling it'll hold on to the phone almost no matter what. This one actually fits my P2XL better than my PXL. https://www.amazon.com/gp/product/B0066BWMNU/ref=oh_aui_search_detailpage?ie=UTF8&psc=1