[Q] Help! Vol - button broken & stuck in bootloop - Desire HD Q&A, Help & Troubleshooting

The Volume- button has been broken on my Desire HD for ages, but this has never been a major issue until today: I got stuck in a bootloop and I don't know how to get into recovery mode!
Please does anyone have any suggestions either on how to get the vol- key to work or on alternative ways to get to recovery? I tried "adb reboot recovery" in cmd.exe but I get error: device not found.
I am worried my phone is broken and I can't afford a new one, so I would be infinitely grateful if someone could give me a hand!
EDIT: I managed to temporarily fix the issue by pulling off the volume rocker and strongly pushing on the button underneath with a pin, but I would still like to know if there is a way to change the key combo that allows to boot into recovery (as my temporary fix might not work next time).

In short yes, I encountered this during a re flash where it said, menu or back disabled.
There is a way just can't recall what I read on here about an alternate button setup.
Running cmw for recovery + version?
--willm
Sent from my Inspire 4G using XDA Premium HD app

So you used another recovery?
I am using cwm 5.0.2.0 (not touch)
(thanks for your reply!)
Sent from my Desire HD using Tapatalk

If the physical button on the ribbon cable is still good...take out your battery, remove the s/n etc sticker carefully-all the way, you'll see a ribbon cable under it about 1/4 inches wide leading to the vol button-use a small plastic twezzer or the like and gently lift the cable and volumn button strip up and out of the slot-it is not fixed in place. Now you can put your battery back in and use the vol buttons with your fingernail. Awkward but for a one time fix in an emergency-it will work. When fixed put it all back--maybe once out you will see the real issue with your volumn not working. Maybe the strip got out of it's position some way.. Of course if the physical buttons are damaged or the ribbon cable is ripped, this will not work.

Hello,
I didn' use the vol buttom in my revocery, install 4ext revocery and than you can with a spedified application start in recocery mod (rom manager for exemple).

I have the same problem with the volume keys. I can't boot into recovery without using ROM Manager... Is there another way?

HELP
HELP

rootntootn said:
If the physical button on the ribbon cable is still good...take out your battery, remove the s/n etc sticker carefully-all the way, you'll see a ribbon cable under it about 1/4 inches wide leading to the vol button-use a small plastic twezzer or the like and gently lift the cable and volumn button strip up and out of the slot-it is not fixed in place. Now you can put your battery back in and use the vol buttons with your fingernail. Awkward but for a one time fix in an emergency-it will work. When fixed put it all back--maybe once out you will see the real issue with your volumn not working. Maybe the strip got out of it's position some way.. Of course if the physical buttons are damaged or the ribbon cable is ripped, this will not work.
Click to expand...
Click to collapse
This worked for me when I had a similar issue. Got it repaired though as I was under warranty (had to convince the repair folks that it had stock though )

Related

Need help!! Plz??!

I need to boot into recovery. I'm stuck at the HTC Evo 4G screen and it won't go any further than that. I would normally get into hboot by holding volume down+power button. Slight problem though. My volume down button does not work...somehow the soldering came loose on the inside and it doesn't work. Anyone know how I can get into recovery?
Get a set of small tipped screwdrivers, take apart your phone see if the button is out of line or if it is actual solder problem.
Sent from my PC36100 using Tapatalk
Yeah, did that earlier. The button is completely off. The solder is broken and I have the button in my hand right now.
I'm using the Revolutionary (sp) recovery and if you hold Volume UP and Power you can load up into Recovery from there. Good luck.

[SOLVED] "SAFE MODE" overlay bottom left, HELP !

Hi guys,
I've been on xda for a long time and done all things on my trusty old desire, but recently, during a rainy day, i tried to listen to a call, and maybe some water got in..... I went turned off, went home, dried the phone for a couple of hours,
Now when i turned it on, there is a message overlay on bottom left of screen, :SAFE MODE:
SAFE mode disables your DATA partition and no other obvious side effects (but its a big problem itself)
I've googled i around and some say its hardware fault, some say they fixed it with some keypress combos.... i tried em all, no luck yet..... keys do work in rom, except the Vol down, trackpad, and power key(it reboots instead locking).
I tried several gb, ics roms, downgraded hboot, then upgraded, many wipes, many reboots...no luck as of now..... Any helpful suggessions are welcome. I love my desire very much and plan to use it (if repaired) for a year atleast....
If there is a workaround, tell me ill try it for sure. My phone out of warranty so i am also willing to open it up myself and in that respect, any guide or tutorial is also welcome. Please guys just anything, even for the sake of it. (i know i sound desperate, coz i really am. Being a student, u cant replace smartphones very easily)
Regards
A broken Desire owner:crying::crying::crying:
It seems your Vol down and trackpad are stuck, so they keep being pressed. Might be a contact problem, but might also be on the mainboard.
ok guys
Lets see,
I opened up my desire using a disassembly video, (pretty hard job finding right screw drivers).....
Now vol down, vol up working..... power key is acting normal (not rebooting the phone on key press),
Search, menu, home, back, all are working perfect......
Optical J-pad NOT working, not pressing, not moving,
And phone still in safe mode....
Now any tips !!!!
Regards
Yasir
Usually you'd go to safe mode when pressing the menu button while booting, but it may be the same with the trackpad (can't test that atm). You say menu button works fine? Try pressing Vol- and Power and see if it reboots, then your trackpad is still stuck (and you can probably fix it like you fixed the volume buttons).
thanks for reply
hi,
OK guys i have some update....
Desire can be put in safe mode by using MENU + POWER key combo, thats the normal process. BUT, if there is water stuck in ANY of the keys, may it be vol up/down, menu, home, optical joypad etc, the DESIRE will detect a Fault in hardware, and go in SAFE MODE ALWAYS, no matter whether u press a combo or not....
IN MY CASE, the optical joypad had the shortcircuit...... i opened my phone myself using a disassembly video, and cud clearly see the burn out wire in optical joypad. So i removed the optical joypad button cable from its connector.
For the rest of the keys, i JUST performed cleaning with cotton cloth, and packed the phone up.
Voila !!!! The phone booted up JUST FINE......
so for all you guys out there, if you encounter this, you know what to do.....
I'll attach the picture of removed OJ later.
Regards
Yasir

[Q] Power button hyper-sensitive

Hi all,
I've had some problems with my S3 power button. It's behaving like it's being pressed when it isn't. Just slightly brushing it, without depressing the button, is registering a press. Pressing the button is behaving like the button is being held.
I've read a number of possible fixes. I tried software options, just to be sure (cleared cache, factory reset). But this is almost certainly a hardware problem.
I stripped the phone down and the physical button itself looks absolutely fine. It is interacting as it should with the internal button on the motherboard. The issue seems to be that the internal button attached to the motherboard (the little white button) is registering clicks even when it's not being fully depressed.
The phone did have some water damage about 6 months ago. I wonder if this could be causing the the phone to mess up now?
I even tried a fix that many people seem to think works: smacking the crap out of the power button itself. It had no affect on my phone - I think that "fix" that is for a power button that is stuck depressed and not a power button registering phantom clicks/being hyper-sensitive.
So I suppose I have the following questions:
1) Has anyone else experienced similar problems and, if so, did they get it fixed?
2) My plan is to try replacing the motherboard/logic board and see if that helps. Does that sound like the best fix or is it overkill?
3) If I'm replacing the motherboard, does it need to be an I747 motherboard or will any S3 model work fine?
4) What's the best source for a motherboard? I don't mind if they're used or refub so long as they work.
Any advice you can offer is welcome.
Cheers.
BenScopato said:
Hi all,
I've had some problems with my S3 power button. It's behaving like it's being pressed when it isn't. Just slightly brushing it, without depressing the button, is registering a press. Pressing the button is behaving like the button is being held.
I've read a number of possible fixes. I tried software options, just to be sure (cleared cache, factory reset). But this is almost certainly a hardware problem.
I stripped the phone down and the physical button itself looks absolutely fine. It is interacting as it should with the internal button on the motherboard. The issue seems to be that the internal button attached to the motherboard (the little white button) is registering clicks even when it's not being fully depressed.
The phone did have some water damage about 6 months ago. I wonder if this could be causing the the phone to mess up now?
I even tried a fix that many people seem to think works: smacking the crap out of the power button itself. It had no affect on my phone - I think that "fix" that is for a power button that is stuck depressed and not a power button registering phantom clicks/being hyper-sensitive.
So I suppose I have the following questions:
1) Has anyone else experienced similar problems and, if so, did they get it fixed?
2) My plan is to try replacing the motherboard/logic board and see if that helps. Does that sound like the best fix or is it overkill?
3) If I'm replacing the motherboard, does it need to be an I747 motherboard or will any S3 model work fine?
4) What's the best source for a motherboard? I don't mind if they're used or refub so long as they work.
Any advice you can offer is welcome.
Cheers.
Click to expand...
Click to collapse
I had the exact same problem with mine, and unfortunately there's not much you can do about it as it's a hardware defect. I haven't tried replacing motherboards or anything, so that might help you. What I did to help with the problem was rerouting my power button to my volume up key so that I can use the power button as little as possible. The only time I use the power button now is when I need to power it on - which causes reboot loops sometimes.
Drisc0 said:
I had the exact same problem with mine, and unfortunately there's not much you can do about it as it's a hardware defect. I haven't tried replacing motherboards or anything, so that might help you. What I did to help with the problem was rerouting my power button to my volume up key so that I can use the power button as little as possible. The only time I use the power button now is when I need to power it on - which causes reboot loops sometimes.
Click to expand...
Click to collapse
Sucks.
I like the sound of your work around, though. Was it pretty simple rerouting the power button?
BenScopato said:
Sucks.
I like the sound of your work around, though. Was it pretty simple rerouting the power button?
Click to expand...
Click to collapse
Ditto, my power button is borked too. Ended up doing the same thing but I don't use my power button at all. I just use rom toolbox to reboot system/into recovery
Rerouting was simple for me as it's baked into the settings in the rom I'm on (ground zero) as it is with most custom ROM'S I've been on. If you're just running stock I'm sure there's an app in the market that'll work however I'm drawing a blank ATM
Sent from my SAMSUNG-SGH-I747 using Tapatalk
brianray14 said:
Ditto, my power button is borked too. Ended up doing the same thing but I don't use my power button at all. I just use rom toolbox to reboot system/into recovery
Rerouting was simple for me as it's baked into the settings in the rom I'm on (ground zero) as it is with most custom ROM'S I've been on. If you're just running stock I'm sure there's an app in the market that'll work however I'm drawing a blank ATM
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Click to expand...
Click to collapse
I'm running CM.
I've had a look through the routing options. What I can't locate is a way to disable the power button completely. My main problem right now is the phantom clicks. I'd rather that button be dead.
Anyone know of a way I can make that happen in CM?
Nevermind. I just physically removed the power button. That did the trick.
For anyone interested, you can replace a faulty power button on the motherboard pretty easily and the parts are cheap. If I wasn't due an upgrade in 4 months I'd probably do that. No need to replace the whole motherboard.
Does anyone know the app to reroute the button? I too have the same problem.

[Q] Power Issues... Even in recovery/download mode

Phone randomly turns off/reboots (mostly reboots). Sometimes the phone won't go past the "SAMSUNG" screen on boot. I booted the phone into recovery and download mode multiple times but it'll reboot after a minute or two.
I've tried another battery and still had the same issue. I've removed the battery and held the power button down to discharge power. I've opened up the phone, blew the dust out, and made sure that the power button was not getting stuck. I'm fairly certain it's not a rogue app causing the issue, but I've factory reset the phone to stock.
Please advise!
dwrdbg said:
Phone randomly turns off/reboots (mostly reboots). Sometimes the phone won't go past the "SAMSUNG" screen on boot. I booted the phone into recovery and download mode multiple times but it'll reboot after a minute or two.
I've tried another battery and still had the same issue. I've removed the battery and held the power button down to discharge power. I've opened up the phone, blew the dust out, and made sure that the power button was not getting stuck. I'm fairly certain it's not a rogue app causing the issue, but I've factory reset the phone to stock.
Please advise!
Click to expand...
Click to collapse
if you have a sd card, sometimes a funky sd card will cause this as well. remove yours for a while to check if its causing your issue
Sounds like the same problem I was having. Take your finger and lightly move it up and down over the power button.. if it acts up or reboots it could be the button issue..
Sent from my SPH-L710 using xda app-developers app
I was having the EXACT same issue. I thought it might be the recent upgrade to the cm11 nightlies since before it was once a week but now it's just non-stop. Is the issue the actual power button switch or the plastic buttons?
Orion78 said:
Sounds like the same problem I was having. Take your finger and lightly move it up and down over the power button.. if it acts up or reboots it could be the button issue..
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
beantek said:
I was having the EXACT same issue. I thought it might be the recent upgrade to the cm11 nightlies since before it was once a week but now it's just non-stop. Is the issue the actual power button switch or the plastic buttons?
Click to expand...
Click to collapse
For me it was the power button itself.. Read my post on how to fix the issue yourself if you dont want to take your phone into Sprint
http://forum.xda-developers.com/showthread.php?t=2679936
Fixed (kind of )
I've taken my phone apart before to replace the speaker/audio jack module after my headphone jack stopped working in one ear (also a common s3 problem). I did as suggested and added a piece of paper wedged in between the button and the button switch. Surprisingly the switch was perfectly clicky so any problem will have to be internally such as corrosion or just worn out. The problem seemed to have been fixed (kind of, not really) as the phone turned on and wouldn't freak out when I rubbed the power/hold button. I got all my data off the phone successfully. The buttons themselves are pretty cheap online but I don't want to have to solder considering I have an upgrade. I'll just get an S5 whenever they are available. Thanks for the help.
Orion78 said:
For me it was the power button itself.. Read my post on how to fix the issue yourself if you dont want to take your phone into Sprint
http://forum.xda-developers.com/showthread.php?t=2679936
Click to expand...
Click to collapse
I'd like to thank everyone for their suggestions. I determined that it was in fact a power button issue.
My "FIX" (for anyone with similar issues):
Temporary:
I removed the logic board from the phone and flicked the button up and down and that helped a little with the button's hypersensitivity. Because a slight tap would make the button "stick" and power off, I took apart the phone and physically removed the plastic power button. I could hit the button if necessary with a small screwdriver or my watch strap thingy, but I did my best to keep the battery from dying out. As for dealing with a lack of "lock" button, I installed an xposed module that let me remap my volume up button as a lock button.
Permanent:
My mother recently upgraded her phone and gave me her S3. Unfortunately it had a cracked screen. I removed her logic board and swapped it out with what was in phone and reactivated her phone as mine.
Thanks for everyone's help, and hopefully this can help someone else too!

Nexus 5x power button unresponsive after screen replacement

Basically, I changed my broken screen (LCD + digitizer) with a new one without the frame. After reassembling the phone, the power button refuses to turn on the phone (it is completely unresponsive). When I plug in the charger, the phone charges, and I can also access the fastboot menu if I hold vol - when plugging in the charger. Both volume buttons are working, the screen and charging port is functional (battery appears to be fully charged as well) so I have no idea why this happened or how to fix it. Has this happened to anyone else? It appears to be a hardware problem (I think) but I really need help from anyone who knows how to fix this problem. The phone was working fine before the screen replacement so I'm not sure what could have gone wrong, please help.
Propa_Way said:
Basically, I changed my broken screen (LCD + digitizer) with a new one without the frame. After reassembling the phone, the power button refuses to turn on the phone (it is completely unresponsive). When I plug in the charger, the phone charges, and I can also access the fastboot menu if I hold vol - when plugging in the charger. Both volume buttons are working, the screen and charging port is functional (battery appears to be fully charged as well) so I have no idea why this happened or how to fix it. Has this happened to anyone else? It appears to be a hardware problem (I think) but I really need help from anyone who knows how to fix this problem. The phone was working fine before the screen replacement so I'm not sure what could have gone wrong, please help.
Click to expand...
Click to collapse
I don't think anyone can help you with a hardware problem. I have a software fix that can give you a invisible softkey power button. One SystemUI.apk should put it in the far upper right hand side of the statusbar, the other on the far right hand side of the navbar.
Tulsadiver said:
I don't think anyone can help you with a hardware problem. I have a software fix that can give you a invisible softkey power button. One SystemUI.apk should put it in the far upper right hand side of the statusbar, the other on the far right hand side of the navbar.
Click to expand...
Click to collapse
Thanks very much. Well the help I'm looking for is to if anyone else experienced this problem and how they got it fixed.
Edit: well I got the phone to start up, I booted it from fastboot (via a pc). I downloaded the apps and tried installing them but it kept saying they were corrupted and could not be installed, do I need root access?
Hello Propaway did you manage to get your power button fixed? I'm having the exact same problem right now
ZomaarEenRobin said:
Hello Propaway did you manage to get your power button fixed? I'm having the exact same problem right now
Click to expand...
Click to collapse
The power button on the board itself seemed broken. I ended up using an app to reroute the power button's function to one of the volume buttons. As with getting the phone itself on, I used fastboot to power on the phone. Have you managed to fix yours?

Categories

Resources