can i ask 1 help how to overclock wfs rom is cm7........i go to cpu settings there
1)available governors
2)min cpu frequency
3)max cpu frequency
4)set on boot
------------------------------------------------------
in available governors
1)lagfree
2)lulzactive
3)lazy
4)braziliznwax
5)smartassv2
6)smartass
7)minmax
8)scary
9)smoothass
10)savagedzen
11)interactivex
12)conservati
13)ondemand
14)userspace
15)powersave
16)lionheart
17)performance
in this which 1 i have o chosse for fast my gameplay
and if make my max cpu to 806 it lags and contiusoly restarts....if i keep it to 787 its bit lagging .....min cpu frequency i hv kept is 200....which is the best frequency ??????
As governor smartass2 is often prefered.
Some phones do not work with maximum voltage and 804 MHz. You will have to reduce it till your phone is stable.
overclocking MAY damage your device. so be careful.
sorry for this old thread but, i have updated the last cm7 and now i can see more cpu states on setcpu such as 825,844 and 864..i overclocked for using these clocks but cpuspy says that these states are "unused"? Interestingly, setcpu says current state is 864 but not cpuspy? is that a bug?
Nice one, unearthing a thread from february ^^
Even if you select a high frequency, your phone might not be able to handle it.
-----------
"You can overclock as much as you want, your phone will always seem too slow."
Related
Hello there,
I've been flashing kernels since I was in LeeDroid Froyo and got no problems. However since I switched to GB based roms such as RCMix3D and TB Fusion, my phone always freezes when I try setting Kernel-Lee-V3.1.1-2.6.35.13-CALLREC or MDJs v19 to maximum overclock so I have no choice to but to stay on stock kernel. I have no ext3/ext4 partition on my SD card in case you ask.
Current ROM: TB Fusion 1.1.2
Radio: 12.54.60.25U_26.09.04.11_M2
Any idea what should I do to solve this issue?
golokipok said:
Hello there,
I've been flashing kernels since I was in LeeDroid Froyo and got no problems. However since I switched to GB based roms such as RCMix3D and TB Fusion, my phone always freezes when I try setting Kernel-Lee-V3.1.1-2.6.35.13-CALLREC or MDJs v19 to maximum overclock
Click to expand...
Click to collapse
uoooo this is sooo dangerous for your handset... u can "smoke" it...
Any idea what should I do to solve this issue?
Click to expand...
Click to collapse
yes, your handset freezes because the overclock that u do its too high... underclock it at 1200-1400mhz & try...
and configure SET CPU features... like the standby status, etc....but do it with common sense....
think about that DHD proccessor goes by default at 1gz, really when we overclock the processor we are putting in danger the security of our device
SERGI.3210 said:
uoooo this is sooo dangerous for your handset... u can "smoke" it...
yes, your handset freezes because the overclock that u do its too high... underclock it at 1200-1400mhz & try...
and configure SET CPU features... like the standby status, etc....but do it with common sense....
think about that DHD proccessor goes by default at 1gz, really when we overclock the processor we are putting in danger the security of our device
Click to expand...
Click to collapse
Haha! I know that overclocking is quite dangerous. Back on the froyo days, my phone is quite stable around 1.8ghz so I'm just wondering why is this happening (maybe my phone's processor is starting to fry up? ). Is there any effect if I'm using smartass profile on those kernels I've mentioned?
golokipok said:
Haha! I know that overclocking is quite dangerous. Back on the froyo days, my phone is quite stable around 1.8ghz so I'm just wondering why is this happening (maybe my phone's processor is starting to fry up? ).
i hope that the processor works or not works (don´t crashes a little bit...)
but the reason of your freezes maybe (almost sure) because froyo & gingerbread don´t works at the same form, and gingerbread need more resources & stability for to work correct... don´t forget that the kernel manages the hardware...
if u force it......... u know what can happen...
golokipok said:
there any effect if I'm using smartass profile on those kernels I've mentioned?
Click to expand...
Click to collapse
it´s possible, take this explanation, read and judge by yourself what´s the better cpu governor...
smartass (Best explanation i've found paraphrases to: based on interactive, but better.)
----
ondemand
Available in most kernels, and the default governor in most kernels. When the CPU load reaches a certain point (see "up threshold" in Advanced Settings), ondemand will rapidly scale the CPU up to meet demand, then gradually scale the CPU down when it isn't needed. - SetCPU website
conservative
Available in some kernels. It is similar to the ondemand governor, but will scale the CPU up more gradually to better fit demand. Conservative provides a less responsive experience than ondemand, but can save battery. - SetCPU website
performance
Available in most kernels. It will keep the CPU running at the "max" set value at all times. This is a bit more efficient than simply setting "max" and "min" to the same value and using ondemand because the system will not waste resources scanning for the CPU load. This governor is recommended for stable benchmarking. - SetCPU website
powersave
Available in some kernels. It will keep the CPU running at the "min" set value at all times. - SetCPU website
userspace
A method for controlling the CPU speed that isn't currently used by SetCPU. For best results, do not use the userspace governor. - SetCPU website
Interactive
The 'interactive' governor has a different approach. Instead of sampling the cpu
at a specified rate, the governor will scale the cpu frequency up when coming
out of idle. When the cpu comes out of idle, a timer is configured to fire
within 1-2 ticks. If the cpu is 100% busy from exiting idle to when the timer
fires then we assume the cpu is underpowered and ramp to MAX speed.
If the cpu was not 100% busy, then the governor evaluates the cpu load over the
last 'min_sample_rate' (default 50000 uS) to determine the cpu speed to ramp down
Click to expand...
Click to collapse
Thanks for the info
SERGI.3210 said:
because froyo & gingerbread don´t works at the same form, and gingerbread need more resources & stability for to work correct... don´t forget that the kernel manages the hardware...
if u force it......... u know what can happen...
Click to expand...
Click to collapse
You have mentioned about those "resources", is there any special measure that I need to do or what? I'm using the smartass profile on those kernels but still *sigh*
Anyway, I've observed on your sig that yours is overclocked @ 1.8ghz even though you're running GB, me envy
golokipok said:
have mentioned about those "resources", is there any special measure that I need to do or what? I'm using the smartass profile on those kernels but still *sigh*
Click to expand...
Click to collapse
you only should do a good over/underclock & set the correct cpu governor for your daily use....
well, you know ho is @MDeeJaay? the developer of MDJ kernels and roms...
he explained smartass with this words:
SMARTASS GOVERNOR - is based on the concept of the interactive governor.
I have always agreed that in theory the way interactive works - by taking over the idle loop - is very attractive. I have never managed to tweak it so it would behave decently in real life. Smartass is a complete rewrite of the code plus more. I think its a success. Performance is on par with the "old" minmax and I think smartass is a bit more responsive. Battery life is hard to quantify precisely but it does spend much more time at the lower frequencies.
Smartass will also cap the max frequency when sleeping to 245Mhz (or if your min frequency is higher than 245 - why?! - it will cap it to your min frequency). Lets take for example the 998/245 kernel, it will sleep at 245.
golokipok said:
, I've observed on your sig that yours is overclocked @ 1.8ghz even though you're running GB, me envy
Click to expand...
Click to collapse
no, no buddy... i only show the max speed nothing more... i set my cpu concretly like this;
CPU GOVERNOR:interactive
MAX SPEED:1113 MHZ
MIN SPEED:245 MHZ
PROFILE: screen off; 245 MHZ max.
245 MHZ min.
in adition i´m going to modify my syg LOL
haha..thanks again. I'm gonna try playing with the frequencies to see which will suit me
i hope someone can make a stable 1.8ghz kernel without the freeze
IT´S POSSIBLE but i don´t want to try it LOL
i love a lot my DHD
ok idk ow to overclock correctly i need a way to make this sense 3.5 rom less laggy an run more smoothly, can anybody help me with this???
Yes just use Daemon Controller (basically functions the same as SetCPU) and set your maximum frequency. For most ROMs I would set it around 1.5Ghz, and set the governor to smartass or smartassv2. The governors will depend on the kernel you're using. For a good sense kernel, I would use this one.
Additionally, you can download Incredicontrol via the market and that will enable you to adjust your voltages, based on the frequency steps. A lot of people prefer to bump the voltage up or down 25% to increase performance or reduce battery drain.
I AM NOT RESPONSIBLE FOR ANY PAIN AND SUFFERING YOUR DEVICE MAY INCUR.
If I helped, slap my Thanks button around a bit.
chattguy said:
Yes just use Daemon Controller (basically functions the same as SetCPU) and set your maximum frequency. For most ROMs I would set it around 1.5Ghz, and set the governor to smartass or smartassv2. The governors will depend on the kernel you're using. For a good sense kernel, I would use this one.
Additionally, you can download Incredicontrol via the market and that will enable you to adjust your voltages, based on the frequency steps. A lot of people prefer to bump the voltage up or down 25% to increase performance or reduce battery drain.
I AM NOT RESPONSIBLE FOR ANY PAIN AND SUFFERING YOUR DEVICE MAY INCUR.
If I helped, slap my Thanks button around a bit.
Click to expand...
Click to collapse
0k the number says 245760 i cant tell which is the 1.5 ghz?
245mhz... That is your lowest frequency. You'll set that as your minimum. Your max should be set at 1497mhz. It'll have some numbers straggling on the end but disregard them. 1497mhz = 1.5Ghz.
Sent from my Incredible 2 using Tapatalk
excuse me; have question about this kernel; i couldn't post in the original thread;
by setting the min clock speed to 768MHZ & the max to 1407MHZ, How much voltage does it spend? by setting the min to 245MHZ & max to 1024MHZ how much? i overclocked to 1407MHZ , i saw more smoothness and speed; but i felt that its consuming more power!
is overclocking harmful to CPU? ( always overclocking )
Rom: MY One V RC4.0 FX
PrimoU GSM
Kernel: Latest Kiss Kernel
Hi
Political correct answer:
Of course OC "can" harm your device - like all OC´ing
Realistic answer:
Most One V devices can handle OCing up to 1.5 without problems
but since this may be specific to chip manifacturing there is no
guarantee that it is. Therefore before using any OC you should
test it very carefully.
And also - Of course running the chip at higher frequencies needs
more power. Simply physics .)
In "normal" daily use the difference is not big because the cpu will
not run at high frequencies most of the time. If you do things
like "heavy" gaming this is of course forcing the cpu to run faster.
To reduce the "effect" a little bit there is a kernel feature called
Undervolting (UV) with that you can reduce the voltage for
specific frequencies. Like OC this is device specific. So some
devices can run stable with more reduced voltage then others
BTW: why to you set the min frequency to 768?
This will limit that the frequency cannot go lower then that if the
device is idle. Running at 245 needs of course less power then 768
max
Thanks for the nice info, well, i heard that some users said that the best frequency for " My One V" rom:
Minimum: 768MHZ
MAX: 1407
I'm using "Set CPU" to OC
So setting the min frequency to 245MHZ will save more power, right?
Sent from my HTC One V using xda app-developers app
Satohiroshi said:
So setting the min frequency to 245MHZ will save more power, right?
Click to expand...
Click to collapse
Yes - especially for the time before the device can go into
"deep sleep" when beeing idle.
The only "disadvantage" is that depending on the govener that you use
there might be a small lag before the frequency scales up
Actually it depends if you notice it at all
If you use govener ondemand it should be no problem
if you use e.g. smartassV2 you might consider thinking about
using some tunables that will reduce that behaviour.
max
Thanks, yeah, i meant for normal activities, like checking Facebook,mail, watching movies ... So ondemand mode would be better
Sent from my HTC One V using xda app-developers app
maxwen said:
Yes - especially for the time before the device can go into
"deep sleep" when beeing idle.
The only "disadvantage" is that depending on the govener that you use
there might be a small lag before the frequency scales up
Actually it depends if you notice it at all
If you use govener ondemand it should be no problem
if you use e.g. smartassV2 you might consider thinking about
using some tunables that will reduce that behaviour.
max
Click to expand...
Click to collapse
What is your recommend governor to integrate with your Titanium-KISS kernel and what is your favourite I/O Scheduler tweaks, for daily use & heavy gaming?
I'm using smartassV2 & i set my I/O Scheduler to deadline until now, because it's peoples favourite
Should i change it to ondemmand to gain a better performance?
Hi
Actually there is already a lot of information about your question
in the KISS kernel thread.
Especially about how to tweak smartassV2 based on "profiles"
max
maxwen said:
Hi
Actually there is already a lot of information about your question
in the KISS kernel thread.
Especially about how to tweak smartassV2 based on "profiles"
max
Click to expand...
Click to collapse
uh, okay...i'll re-read the info once again :good:
I've been using System Tuner Pro for undervolting on the most often used frequencies and I got those result:
19MHz (is this 'deep sleep'?) 800mV
768-800mV
998-800
1070-975
1150-1150
The problem is, that if I set the voltage under the stock 925mV for 384, 245 or 128mV, the phone crashes almost instantly. How is it possible that higher freqs like 998MHz run just fine on 800MHz but those much lower ones wont?
If your phone crash on low voltages you need to increase them
No sh!t, Sherlock.
Talking about irrelevant responses...
Hey guys,
i got a problem adjusting the cpu frequencies on my Galaxy S4 mini GT9195.
For example, i change it to 162mhz minimum and 1026mhz maximum and the smartassV2 govenor. Then that changes ramdomly to some weird frequencies automaticly and out of a sudden. Like 1458mhz minimum and maximum.
I use the cyanogenmod11 M7 rom and the f4ktion 1.5.0 Kernel (the cyanogen kernel does the same btw)
As App for adjusting i use the Kernel Tweaker, but even if i do it in the System settings its doing the same...
I did some undervolting, this stays as i set it.
I hope you guys can help me its annoying to check it every houre and see that it changed again and drains my battery
Sebastian
Devices using a modern qualcomm cpu, relies on two userspace daemons (mpdecision and thermald) to manage frequency and thermal throttling. So mpdecision takes care of the frequencies and cpu hot-plugging (when to engage additional cores or not), and thermald lowers the frequency if the temperature gets too high, in order to protect the cpu from overheating. This is not compatible with the frequency settings in CM or any third party app with similar functionality, as they will always override whatever you set there.
arco68 said:
Devices using a modern qualcomm cpu, relies on two userspace daemons (mpdecision and thermald) to manage frequency and thermal throttling. So mpdecision takes care of the frequencies and cpu hot-plugging (when to engage additional cores or not), and thermald lowers the frequency if the temperature gets too high, in order to protect the cpu from overheating. This is not compatible with the frequency settings in CM or any third party app with similar functionality, as they will always override whatever you set there.
Click to expand...
Click to collapse
I see.. Thanks for the answer mate, so there's no way to save battery like this? It just seems sometimes that it's stuck at some frequencies...
Well, you could make a custom boot image that disables those daemons, but it could cause more harm than good.
Sebastianm1989 said:
Hey guys,
i got a problem adjusting the cpu frequencies on my Galaxy S4 mini GT9195.
For example, i change it to 162mhz minimum and 1026mhz maximum and the smartassV2 govenor. Then that changes ramdomly to some weird frequencies automaticly and out of a sudden. Like 1458mhz minimum and maximum.
I use the cyanogenmod11 M7 rom and the f4ktion 1.5.0 Kernel (the cyanogen kernel does the same btw)
As App for adjusting i use the Kernel Tweaker, but even if i do it in the System settings its doing the same...
I did some undervolting, this stays as i set it.
I hope you guys can help me its annoying to check it every houre and see that it changed again and drains my battery
Sebastian
Click to expand...
Click to collapse
f4ktion kernel 1.5.0 is not designed for M7. For M7 use 1.4.5.
I'm right now with nightly 0703, kernel 1.5.0, mpdecision disable and MSM Hotplug enable (performance control). With this settings that bug disapeared. 162 mhz - 1728 mhz; smartassh3; ROW.
In M7, and 1.4.5 kernel, the only governor that works with 162 mhz and don't change to 1458 mhz is the Ondemand.