Develop Bugs

[Q] Defy Linux USB tethering

Hello,
I have a problem with my Motorola Defy cell phone.
I want to connect it via usb and use it as a modem with wvdial. The problem is, when connecting the usb it only registers as a mass storage:
Code:
usb 2-1: new high speed USB device using ehci_hcd and address 11
scsi12 : usb-storage 2-1:1.0
scsi 12:0:0:0: Direct-Access Motorola MB525 0001 PQ: 0 ANSI: 2
sd 12:0:0:0: Attached scsi generic sg2 type 0
sd 12:0:0:0: [sdb] 3911680 512-byte logical blocks: (2.00 GB/1.86 GiB)
sd 12:0:0:0: [sdb] Write Protect is off
sd 12:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 12:0:0:0: [sdb] Assuming drive cache: write through
sd 12:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 12:0:0:0: [sdb] Assuming drive cache: write through
sd 12:0:0:0: [sdb] Attached SCSI removable disk
lsusb:
Code:
Bus 002 Device 011: ID 22b8:41db Motorola PCS Droid/Milestone (Debug mode)
No tty device gets created and there is no new device in "ifconfig -a"
I tested all usb connecting modes from the phone and also tried it with USB debugging.
Does anybody know how to ignore the mass storage and just use the modem? (usbnet is loaded)
Thanks.

I think that you need anyway some sort of app running on the phone (as example easytether) to do that; with other words I don't think you can directly access the phone internal modem.
PS: I'm currently using easytether + debian squeeeze.
Sent from my MB525 using XDA App

You have to activate debugging - then Defy will export appropriate USB interfaces and endpoints:
Code:
Bus 002 Device 009: ID 22b8:41da Motorola PCS
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x22b8 Motorola PCS
idProduct 0x41da
bcdDevice 2.16
iManufacturer 1 Motorola
iProduct 2 MB525
iSerial 3 016079B40502B019
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 150
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 4 Motorola Config 31
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 6 Motorola Communication Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 9
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 7 Motorola Data Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 10 Mobile Direct Line
bInterfaceProtocol 1
iInterface 8 Motorola Networking Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 6 Imaging
bInterfaceSubClass 1 Still Image Capture
bInterfaceProtocol 1 Picture Transfer Protocol (PIMA 15470)
iInterface 9 Motorola MTP Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 10 Motorola ADB Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
However, UDEV does not recognise it as network interface on the spot
because of (my speculation):
Code:
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
So udev rules need tweaking, and I did not found how to do it yet
(debugging android layouts is much easier)

Hi,
Did you succeed with the udev rules ?
I have a milestone2 and under archlinux it's the same problem, the interface is not detected.
Thanks

I solved it with the app azilink which is opensource and free: code.google.com/p/azilink/
Works perfect!
Greetings!

change idProduct from my samsung nexus?

Is there a way to change idProduct from my samsung nexus?
Here are my reasons: I have connected my smartphone on a VM (Virtual Machine) under KVM, I made the mistake of backing up my VM with the connected smartphone.
I made an upgrade of my smartphone, this update to also change the idProduct of 6860 to 685c. Since I can not restart my VM KVM, see this error
HTML:
"Traceback (most recent call last):
File "/usr/share/virt-manager/virtManager/asyncjob.py", line 44, in cb_wrapper
callback(asyncjob, *args, **kwargs)
File "/usr/share/virt-manager/virtManager/asyncjob.py", line 65, in tmpcb
callback(*args, **kwargs)
File "/usr/share/virt-manager/virtManager/domain.py", line 1050, in startup
self._backend.create()
File "/usr/lib/python2.7/dist-packages/libvirt.py", line 365, in create
if ret == -1: raise libvirtError ('virDomainCreate() failed', dom=self)
libvirtError: internal error Did not find USB device 4e8:6860"
Have you ways to solve my problem?
# lsusb -v ....(extract)
HTML:
Bus 002 Device 012: ID 04e8:685c Samsung Electronics Co., Ltd
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x04e8 Samsung Electronics Co., Ltd
idProduct 0x685c
bcdDevice 2.16
iManufacturer 2 samsung
iProduct 3 Galaxy
...
idProduct was before 6860 !!!

Request - Linux users

I need the vid and pid of the Kindle Fire in fastboot mode so I can manually configure my VM's USB, again. TIA
[Edit:]Better yet, the output of lsusb for the Kindle Fire (only) in fastboot would be perfect.

soupmagnet said:
I need the vid and pid of the Kindle Fire in fastboot mode so I can manually configure my VM's USB, again. TIA
[Edit:]Better yet, the output of lsusb for the Kindle Fire (only) in fastboot would be perfect.
Click to expand...
Click to collapse
Those values are dependent on the bootloader. Output from "lsusb -v" I had in my notes...
Stock
Code:
Bus 001 Device 014: ID 1949:0006 Lab126
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1949 Lab126
idProduct 0x0006
bcdDevice 1.00
iManufacturer 5 Amazon
iProduct 1 kindle
iSerial 2 0123456789ABCDEF
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 3 Android Fastboot
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 3
iInterface 4 Android Fastboot
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x000a
(Bus Powered)
Remote Wakeup Enabled
FFF
Code:
Bus 001 Device 011: ID 18d1:0100 Google Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x18d1 Google Inc.
idProduct 0x0100
bcdDevice 1.00
iManufacturer 5 Amazon
iProduct 1 kindle
iSerial 2 0123456789ABCDEF
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 3 Android Fastboot
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 3
iInterface 4 Android Fastboot
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x000a
(Bus Powered)
Remote Wakeup Enabled

Yeah, VMware still refuses to detect the device in fastboot, no matter what I do. I got the Mac to detect it again though. Restoring a backup fixed it, but I have no idea why it stopped working in the first place.
I still need to get VMware to detect, so if anyone has had luck in that regard, I would greatly appreciate any information provided.

stuck in fastboot after trying to root

helloy guys I have 6.3.1 when I tried to root with kindle fire utility after installing the drivers (I dont have sdk) from KINDLE FIRE DRIVER when the kf rebooted into fastboot the kf utility says waiting for device and the computer not recognized the device so what should I do please hurry up this isn't my device and I his owner want it in less than 5 hours

Ok forget about Windows and create a Linux LiveUSB using this:
http://forum.xda-developers.com/showthread.php?p=31449443
You shouldn't have any trouble with adb or fastboot commands, unless it is an un-rooted stock device, then you'll have to use Pokey9000's fbmode or a factory programming cable to enable fastboot.

Okay it's unrooted stock 6.3.1 and I have a linux computer
what I should do in linux with my kindle fire (first time to connect it to my kf)
I'm in the fastboot now with first time connecting it to computer and missed drivers oooooh a lot of problems I think I have drivers because the kfu said online when connecting it
Please walk with me step by step

Run SoupKit, then:
http://forum.xda-developers.com/showthread.php?p=25730650

Okay I'm in fastboot now I will go to this
http://forum.xda-developers.com/showthread.php?p=25730650
if yes which one I should do?

Also I cannot push files with adb commands because I'm in fb mode

hemo-ali said:
Also I cannot push files with adb commands because I'm in fb mode
Click to expand...
Click to collapse
Use fastboot to install recovery and boot into recovery to send adb commands.

I know that but fastboot commands cannot catch my device

is this driver problems or there is custom commands I'm using
fastboot -i 0x1949 devices
and this shows nothing
Please help me I'm beginner

Did you run SoupKit?

Not yet
so you mean i will download soupkit then run the fastboot commands within it right?

No. Download SoupKit in Linux.
Read the SoupKit thread in it's entirety.
Extract the SoupKit
Follow the directions in the README

when I run this after installing soup kit
fastboot -i 0x1949 flash recovery twrp-blaze-2.0.0RC0.img
I get waiting for devices

is there any drivers for linux

SoupKit installs the appropriate drivers for Linux. Enter the following command and paste the output here.
lsusb -v

this is the output
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.02
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.02
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.02
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.02
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.02
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 004 Device 002: ID 0458:003a KYE Systems Corp. (Mouse Systems) NetScroll+ Mini Traveler / Genius NetScroll 120
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0458 KYE Systems Corp. (Mouse Systems)
idProduct 0x003a NetScroll+ Mini Traveler / Genius NetScroll 120
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 62
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Click to expand...
Click to collapse

Also, what Linux distro are you using?

ubuntu 12.10

32bit? 64bit?

32 bit

Pixel XL Pie connects to USB3 at USB2 speed only

I just realized my Pixel XL - verizon, unlocked bootlader, TRWP, Pie - is connecting to Windows only at USB 2.0 (high speed) rather than 3.0 (super speed).
I am using type A blue 3.0 socket with correct drivers on Windows side (external HDD etc have no problems), and I am trying both the stock Google cable (which has a white type A plug to be fair?!) and also a Benson-approved "Veckle" USB type-A 3.0 (blue) to USB-C cable.
I tried putting the phone USB mode in both file-transfer and "no data" (for debugging) but no difference.
I'm verifying this using USB Device Tree Viewer, I will dump the report below, but it's clear from file transfer speeds that it's way too slow @ 30 MB/s write & read.
Code:
Intel(R) USB 3.0 eXtensible Host Controller - 1.0 (Microsoft)
\---USB Root Hub (USB 3.0)
|HS-[1-1]
|HS-[1-2]
|HS-[1-3]
|HS-[1-4]: USB Composite Device
=========================== USB Port4 ===========================
Connection Status : 0x01 (Device is connected)
Port Chain : 1-4
Properties : 0x01
IsUserConnectable : yes
PortIsDebugCapable : no
PortHasMultiCompanions : no
PortConnectorIsTypeC : no
ConnectionIndex : 4
CompanionIndex : 0
CompanionHubSymLnk : USB#ROOT_HUB30#4&2060378&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
CompanionPortNumber : 20
======================== USB Device ========================
+++++++++++++++++ Device Information ++++++++++++++++++
Device Description : USB Composite Device
Device Path : \\?\usb#vid_18d1&pid_4ee2#ht68t0203009#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Device ID : USB\VID_18D1&PID_4EE2\HT68T0203009
Hardware IDs : USB\VID_18D1&PID_4EE2&REV_0318 USB\VID_18D1&PID_4EE2
Driver KeyName : {36fc9e60-c465-11cf-8056-444553540000}\0013 (GUID_DEVCLASS_USB)
Driver : \SystemRoot\System32\drivers\usbccgp.sys (Version: 10.0.17134.1 Date: 2018-04-12)
Driver Inf : C:\WINDOWS\inf\usb.inf
Legacy BusType : PNPBus
Class : USB
Class GUID : {36fc9e60-c465-11cf-8056-444553540000} (GUID_DEVCLASS_USB)
Interface GUID : {a5dcbf10-6530-11d2-901f-00c04fb951ed} (GUID_DEVINTERFACE_USB_DEVICE)
Service : usbccgp
Enumerator : USB
Location Info : Port_#0004.Hub_#0001
Location IDs : PCIROOT(0)#PCI(1400)#USBROOT(0)#USB(4), ACPI(_SB_)#ACPI(PCI0)#ACPI(XHC_)#ACPI(RHUB)#ACPI(HS04)
Container ID : {dc988900-f60c-5af4-b6da-af1e52beda4a}
Manufacturer Info : (Standard USB Host Controller)
Capabilities : 0x94 (Removable, UniqueID, SurpriseRemovalOK)
Status : 0x0180600A (DN_DRIVER_LOADED, DN_STARTED, DN_DISABLEABLE, DN_REMOVABLE, DN_NT_ENUMERATOR, DN_NT_DRIVER)
Problem Code : 0
Address : 4
Power State : D0 (supported: D0, D3, wake from D0)
Child Device 1 : Pixel XL
DevicePath : -
Device ID : USB\VID_18D1&PID_4EE2&MI_00\8&2912D0A1&0&0000
Class : WPD
Child Device 2 : Android Composite ADB Interface
DevicePath : -
Device ID : USB\VID_18D1&PID_4EE2&MI_01\8&2912D0A1&0&0001
Class : AndroidUsbDeviceClass
---------------- Connection Information ---------------
Connection Index : 0x04 (4)
Connection Status : 0x01 (DeviceConnected)
Current Config Value : 0x01
Device Address : 0x0E (14)
Is Hub : 0x00 (no)
Number Of Open Pipes : 0x05 (5)
Device Bus Speed : 0x02 (High-Speed)
Pipe0ScheduleOffset : 0x00 (0)
Pipe1ScheduleOffset : 0x00 (0)
Pipe2ScheduleOffset : 0x00 (0)
Pipe3ScheduleOffset : 0x00 (0)
Pipe4ScheduleOffset : 0x00 (0)
--------------- Connection Information V2 -------------
Connection Index : 0x04 (4)
Length : 0x10 (16 bytes)
SupportedUsbProtocols : 0x03
Usb110 : 1 (yes)
Usb200 : 1 (yes)
Usb300 : 0 (no)
ReservedMBZ : 0x00
Flags : 0x00
DevIsOpAtSsOrHigher : 0 (Is not operating at SuperSpeed or higher)
DevIsSsCapOrHigher : 0 (Is not SuperSpeed capable or higher)
DevIsOpAtSsPlusOrHigher : 0 (Is not operating at SuperSpeedPlus or higher)
DevIsSsPlusCapOrHigher : 0 (Is not SuperSpeedPlus capable or higher)
ReservedMBZ : 0x00
---------------------- Device Descriptor ----------------------
bLength : 0x12 (18 bytes)
bDescriptorType : 0x01 (Device Descriptor)
bcdUSB : 0x200 (USB Version 2.00)
bDeviceClass : 0x00 (defined by the interface descriptors)
bDeviceSubClass : 0x00
bDeviceProtocol : 0x00
bMaxPacketSize0 : 0x40 (64 bytes)
idVendor : 0x18D1 (Google Inc.)
idProduct : 0x4EE2
bcdDevice : 0x0318
iManufacturer : 0x01 (String Descriptor 1)
Language 0x0409 : "Google"
iProduct : 0x02 (String Descriptor 2)
Language 0x0409 : "Pixel XL"
iSerialNumber : 0x03 (String Descriptor 3)
Language 0x0409 : "HT68T0203009"
bNumConfigurations : 0x01 (1 Configuration)
------------------ Configuration Descriptor -------------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x02 (Configuration Descriptor)
wTotalLength : 0x003E (62 bytes)
bNumInterfaces : 0x02 (2 Interfaces)
bConfigurationValue : 0x01 (Configuration 1)
iConfiguration : 0x00 (No String Descriptor)
bmAttributes : 0x80
D7: Reserved, set 1 : 0x01
D6: Self Powered : 0x00 (no)
D5: Remote Wakeup : 0x00 (no)
D4..0: Reserved, set 0 : 0x00
MaxPower : 0xFA (500 mA)
---------------- Interface Descriptor -----------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x04 (Interface Descriptor)
bInterfaceNumber : 0x00
bAlternateSetting : 0x00
bNumEndpoints : 0x03 (3 Endpoints)
bInterfaceClass : 0x06 (Image)
bInterfaceSubClass : 0x01 (Still Imaging device)
bInterfaceProtocol : 0x01
iInterface : 0x07 (String Descriptor 7)
Language 0x0409 : "MTP"
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x81 (Direction=IN EndpointID=1)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0200 (max 512 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x01 (Direction=OUT EndpointID=1)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0200 (max 512 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x82 (Direction=IN EndpointID=2)
bmAttributes : 0x03 (TransferType=Interrupt)
wMaxPacketSize : 0x001C
Bits 15..13 : 0x00 (reserved, must be zero)
Bits 12..11 : 0x00 (0 additional transactions per microframe -> allows 1..1024 bytes per packet)
Bits 10..0 : 0x1C (28 bytes per packet)
bInterval : 0x06 (6 ms)
---------------- Interface Descriptor -----------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x04 (Interface Descriptor)
bInterfaceNumber : 0x01
bAlternateSetting : 0x00
bNumEndpoints : 0x02 (2 Endpoints)
bInterfaceClass : 0xFF (Vendor Specific)
bInterfaceSubClass : 0x42
bInterfaceProtocol : 0x01
iInterface : 0x06 (String Descriptor 6)
Language 0x0409 : "ADB Interface"
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x02 (Direction=OUT EndpointID=2)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0200 (max 512 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x83 (Direction=IN EndpointID=3)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0200 (max 512 bytes)
bInterval : 0x00 (never NAKs)
----------------- Device Qualifier Descriptor -----------------
bLength : 0x0A (10 bytes)
bDescriptorType : 0x06 (Device_qualifier Descriptor)
bcdUSB : 0x200 (USB Version 2.00)
bDeviceClass : 0x00 (defined by the interface descriptors)
bDeviceSubClass : 0x00
bDeviceProtocol : 0x00
bMaxPacketSize0 : 0x40 (64 Bytes)
bNumConfigurations : 0x01 (1 other-speed configuration)
bReserved : 0x00
------------ Other Speed Configuration Descriptor -------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x07 (Other_speed_configuration Descriptor)
wTotalLength : 0x003E (62 bytes)
bNumInterfaces : 0x02 (2 Interfaces)
bConfigurationValue : 0x01 (Configuration 1)
iConfiguration : 0x00 (No String Descriptor)
bmAttributes : 0x80
D7: Reserved, set 1 : 0x01
D6: Self Powered : 0x00 (no)
D5: Remote Wakeup : 0x00 (no)
D4..0: Reserved, set 0 : 0x00
MaxPower : 0xFA (500 mA)
---------------- Interface Descriptor -----------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x04 (Interface Descriptor)
bInterfaceNumber : 0x00
bAlternateSetting : 0x00
bNumEndpoints : 0x03 (3 Endpoints)
bInterfaceClass : 0x06 (Image)
bInterfaceSubClass : 0x01 (Still Imaging device)
bInterfaceProtocol : 0x01
iInterface : 0x07 (String Descriptor 7)
Language 0x0409 : "MTP"
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x81 (Direction=IN EndpointID=1)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0040 (max 64 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x01 (Direction=OUT EndpointID=1)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0040 (max 64 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x82 (Direction=IN EndpointID=2)
bmAttributes : 0x03 (TransferType=Interrupt)
wMaxPacketSize : 0x001C
Bits 15..13 : 0x00 (reserved, must be zero)
Bits 12..11 : 0x00 (0 additional transactions per microframe -> allows 1..1024 bytes per packet)
Bits 10..0 : 0x1C (28 bytes per packet)
bInterval : 0x06 (6 ms)
---------------- Interface Descriptor -----------------
bLength : 0x09 (9 bytes)
bDescriptorType : 0x04 (Interface Descriptor)
bInterfaceNumber : 0x01
bAlternateSetting : 0x00
bNumEndpoints : 0x02 (2 Endpoints)
bInterfaceClass : 0xFF (Vendor Specific)
bInterfaceSubClass : 0x42
bInterfaceProtocol : 0x01
iInterface : 0x06 (String Descriptor 6)
Language 0x0409 : "ADB Interface"
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x02 (Direction=OUT EndpointID=2)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0040 (max 64 bytes)
bInterval : 0x00 (never NAKs)
----------------- Endpoint Descriptor -----------------
bLength : 0x07 (7 bytes)
bDescriptorType : 0x05 (Endpoint Descriptor)
bEndpointAddress : 0x83 (Direction=IN EndpointID=3)
bmAttributes : 0x02 (TransferType=Bulk)
wMaxPacketSize : 0x0040 (max 64 bytes)
bInterval : 0x00 (never NAKs)
-------------------- String Descriptors -------------------
------ String Descriptor 0 ------
bLength : 0x04 (4 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language ID[0] : 0x0409 (English - United States)
------ String Descriptor 1 ------
bLength : 0x0E (14 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language 0x0409 : "Google"
------ String Descriptor 2 ------
bLength : 0x12 (18 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language 0x0409 : "Pixel XL"
------ String Descriptor 3 ------
bLength : 0x1A (26 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language 0x0409 : "HT68T0203009"
------ String Descriptor 6 ------
bLength : 0x1C (28 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language 0x0409 : "ADB Interface"
------ String Descriptor 7 ------
bLength : 0x08 (8 bytes)
bDescriptorType : 0x03 (String Descriptor)
Language 0x0409 : "MTP"
This sucks as one reason I chose the Pixel was it's USB 3.0 support, as opposed to certain other dismal implementations of USB-C with only 2.0 transfer! and I want to be able to get video off the phone at maximal speed.
Any input?

You sure it's not the phone's internal memory bottlenecking the transfer? A phone doesn't work like a flash drive, there's a lot more going on. The OS has to run the process to copy the file from internal storage and over USB to the PC. A flash drive just plugs in and gets read/written, with virtually no overhead for handling processes like those.
Also, using adb should be considerably faster than MTP for file transfers. I've also read that some people have better luck with a USB C to USB C cable rather than USB A to USB C.

borxnx said:
You sure it's not the phone's internal memory bottlenecking the transfer? A phone doesn't work like a flash drive, there's a lot more going on. The OS has to run the process to copy the file from internal storage and over USB to the PC. A flash drive just plugs in and gets read/written, with virtually no overhead for handling processes like those.
Also, using adb should be considerably faster than MTP for file transfers. I've also read that some people have better luck with a USB C to USB C cable rather than USB A to USB C.
Click to expand...
Click to collapse
I'm sure it's connecting at USB 2.0 as above, despite every hardware component being USB 3.0.
I was measuring that throughput using adp push/pull actually, but it's the same with MTP.
I don't know what the speeds would be with USB 3.0 but I presume they should be at least a bit faster! I can't try a USB-C to C cable just now as my PC doesn't have a socket.