Tetrax Magnet Mount for Galaxy Nexus - Samsung Galaxy Nexus

Has anybody tried the tetrax mounts yet with their galaxy nexus? Before I purchase one I'm curious of two things.
1. How well does the the magnet stick to the battery door since the battery cover is textured? I have an extra cover that I'll use simply for this.
2. Does the magnet interfere with the NFC and/or screen at all?
In case your not sure what I'm referring to:
http://store.tetrax.us/xway-line/fixway

I have used this on other phones, including my G2, MyTouch 3G and G1 and it worked very well on all those phones. However, due to the textured back on the Galaxy Nexus, the metal button that stick to the battery door does not stay on. I have tried replacing the double sided tape with stronger automotive 3M tape, but that doesn't work either. It'll stay on for a little while and come back off. The only solution would be to find a battery door that is smooth.
I can't answer if it interferes with NFC or the screen, but it shouldn’t. If anything, it might interfere with the magnet on the compass, but that has not been the case with my other phones.

MetalMessiah78 said:
I have used this on other phones, including my G2, MyTouch 3G and G1 and it worked very well on all those phones. However, due to the textured back on the Galaxy Nexus, the metal button that stick to the battery door does not stay on. I have tried replacing the double sided tape with stronger automotive 3M tape, but that doesn't work either. It'll stay on for a little while and come back off. The only solution would be to find a battery door that is smooth.
I can't answer if it interferes with NFC or the screen, but it shouldn’t. If anything, it might interfere with the magnet on the compass, but that has not been the case with my other phones.
Click to expand...
Click to collapse
Thanks,
So you've actually tried it on the GNex and it don't stick very well? Did you by chance try holding it on there for several hours with a strong clamp or anything? I really want one of these but worried it's a waste of money with this phone

I have actually tried it, but not with a clamp. Just following the regular directions. On my other phones, it created a very strong bond and it takes a lot of effort to remove. With the Nexus, it stays on the first couple of times you mount it, but that's about it. It's not an issue with the weight, as the G2 feels twice as heavy as the Nexus, especially with an extra capacity battery. It's the texture on the battery door. It almost feels like it has a Teflon coating.

MetalMessiah78 said:
I have actually tried it, but not with a clamp. Just following the regular directions. On my other phones, it created a very strong bond and it takes a lot of effort to remove. With the Nexus, it stays on the first couple of times you mount it, but that's about it. It's not an issue with the weight, as the G2 feels twice as heavy as the Nexus, especially with an extra capacity battery. It's the texture on the battery door. It almost feels like it has a Teflon coating.
Click to expand...
Click to collapse
Would you mind holding up one of the magnets to the battery door and test out the NFC to see if it interferes with it (if you have the ability to). This is my main question as I could always put the magnet on a case I guess.
Thanks!

I don't have another NFC device to try it right now, but my brother has the Nexus S and I can try it when I see him later tonight. The magnet doesn't go on the battery door though. What you stick on the battery door is just a piece of metal. The actual magnet is on the device that you mount to your dash or vent, so unless you plan on using NFC while it's on your dash, it should not interfere.
Plus, NFC uses low power radio frequency to transfer information (similar to Bluetooth). It does not use magnets. The only thing in the phone that could be affected would be the compass, as it finds your relation to magnetic North. Even then, I'm sure the compass works through software and is not an actual magnet, as it has never affected GPS. As a matter of fact, I have 2 Tetrax products, the one that mounts to the dash, which I have in my car, and the one that you attach to the vent for when I use a rental on trips for the sole purpose of Navigation. As you can imagine, I was very disappointed when I could not get the metal button to stick. I might have to try it with a case also.

MetalMessiah78 said:
I don't have another NFC device to try it right now, but my brother has the Nexus S and I can try it when I see him later tonight. The magnet doesn't go on the battery door though. What you stick on the battery door is just a piece of metal. The actual magnet is on the device that you mount to your dash or vent, so unless you plan on using NFC while it's on your dash, it should not interfere.
Plus, NFC uses low power radio frequency to transfer information (similar to Bluetooth). It does not use magnets. The only thing in the phone that could be affected would be the compass, as it finds your relation to magnetic North. Even then, I'm sure the compass works through software and is not an actual magnet, as it has never affected GPS. As a matter of fact, I have 2 Tetrax products, the one that mounts to the dash, which I have in my car, and the one that you attach to the vent for when I use a rental on trips for the sole purpose of Navigation. As you can imagine, I was very disappointed when I could not get the metal button to stick. I might have to try it with a case also.
Click to expand...
Click to collapse
Awesome so yea I don't think it'll interfere because I was thinking the part you stick to the back of the phone is magnetic, but if your saying it's not all should be well. Either way I went ahead and ordered it yesterday anyway so I'll figure out a way to get it to stick to either the door or a case. Thanks for your insight!

Nope, it's just a metal button. It actually comes with 4 or 5 different ones of all sizes and styles.

I have this installed on my nexus, I put the mount on my dash and the NFC sticker on my knob for the ac that get covered up. Everytime I put my phone on the mount, the nfc changes it to car mode, volume up, full brightness and launches sirius xm radio...works very well, sometimes I have to move it a bit to get to read the nfc, but thats only cause i have the nfc a little too far at the bottom of the phone and it mounts at a slight angle, not due to any interference at all. I have NFC chips all around and never have problems reading them at all, probably a good idea not to mount the metal chip right in the middle of the battery area, just in case. I also used a clamp to hold it on for about 3 or 4 hours and has had little trouble sticking to the texture.
I have had a few incidents if I pull off the phone, rather than slide it off the backing will actually unclip a single clip.

@ejkeebler what do you mean by NFC stickers all around? Did you make stickers to automatically change your settings on your phone? That's brilliant! How did you do it?
I might also have to try a clamp. I don't really want to put a case on my phone.

MetalMessiah78 said:
@ejkeebler what do you mean by NFC stickers all around? Did you make stickers to automatically change your settings on your phone? That's brilliant! How did you do it?
I might also have to try a clamp. I don't really want to put a case on my phone.
Click to expand...
Click to collapse
I also have NFC stickers everywhere. have them when I walk in the front door of my house, one in my office at work, one in each vehicle, one in my wallet LOL. They are awesome. Set them to change settings or do tasker tasks and you can rewrite over them if you ever want to change anything. One of the best phone features I've ever used. That's why i was concerned about the magnets interfering with the NFC!

dcoy82 said:
I also have NFC stickers everywhere. have them when I walk in the front door of my house, one in my office at work, one in each vehicle, one in my wallet LOL. They are awesome. Set them to change settings or do tasker tasks and you can rewrite over them if you ever want to change anything. One of the best phone features I've ever used. That's why i was concerned about the magnets interfering with the NFC!
Click to expand...
Click to collapse
Where can I get / how do I 'program' these NFC Stickers?? This sounds awesome.

raing said:
Where can I get / how do I 'program' these NFC Stickers?? This sounds awesome.
Click to expand...
Click to collapse
A quick search came up with this: http://www.tagstand.com/
Seems like this could open up a whole line of fun options. Would love to hear how others have done it, though.

raing said:
Where can I get / how do I 'program' these NFC Stickers?? This sounds awesome.
Click to expand...
Click to collapse
www.tagstand.com to purchase the tags. Tell him DCoy82 sent you! The 30mm ultralight c circle NDEF formatted seem to be the only ones I've bought that work with the nexus so far.
Once you get them you can download program called NFC Task Launcher off the market to program them.
Sent from my A500 using Tapatalk

dcoy82 said:
www.tagstand.com to purchase the tags. Tell him DCoy82 sent you! The 30mm ultralight c circle NDEF formatted seem to be the only ones I've bought that work with the nexus so far.
Once you get them you can download program called NFC Task Launcher off the market to program them.
Sent from my A500 using Tapatalk
Click to expand...
Click to collapse
That is so awesome. This is my first phone with NFC so I'm barely starting to learn all the cool things that you can do with it. I tried Android Beam for the first time with my brother on Tuesday and it works great, though I wish you could beam other things such as pictures. By the way, the metal button does not interfere with NFC. I will let them know that you recommended me. Thank you!

If your interested in NFC, here's a few spots that got me started
http://androidforums.com/nexus-s/336155-what-do-you-use-nfc-tasker.html
http://www.readwriteweb.com/archives/weekend_project_make_your_own_nfc_tags.php
http://www.youtube.com/watch?v=LnqmyNEQPq0&feature=email&email=comment_reply_received
and the tags I bought were from here:
http://tagsfordroid.com/tags/Home.html
I got them cause i liked the having the android on them, i think they are a tiny bit less expensive elsewhere, and these are a little thicker than I'd like (like a puffy sticker, about the same thickness of a penny) but you can get many in other places.
by itself i'm not sure nfc task launcher does it for me, but in combination with tasker, it's ridiculous how much can be done....would still love to see what others have come up with.

I love those stickers with the Android! Thanks for the links. I will need to read up on it more. I am definitely interested. This is a lot more exciting stuff then what Google showed off at the I/O last year!

Thats a good idea. Being in IT, we have dead Hard Drives laying around that have awesome magnets in them. They're real slim. I bet I could superglue one to my nexus's battery cover for under the TPU case that would hold. They're thin so it might not screw with the case (but it might).

ejkeebler said:
I got them cause i liked the having the android on them, i think they are a tiny bit less expensive elsewhere, and these are a little thicker than I'd like (like a puffy sticker, about the same thickness of a penny) but you can get many in other places.
Click to expand...
Click to collapse
Yeah, it looks like it's $8 for 2. I just picked up 5 over at tagstand.com for the same price and found 10 for $13 over at http://buynfcstickers.com.

Hopefully you guys are all having good experience with the guy at tag stand. His customer service was great for me and I'll definatley be going back there in the future.
Oh and by the way, I got my new tetrax magnet set in today and not having any issues with the magnet at allowing necessary nor with the metal part sticking to the stock battery door. Only real issue so far is you have to slide it off just right or the battery door just pops off the nexus lol. Highly recommend though!
Sent from my A500 using Tapatalk

Related

Getting opinions about Tetrax Fix magnet car holder

Guys, I need your opinion about a magnetic car holder for SGS3.
Is it safe to use the Tetrax Fix magnetic car holder?
I mean, my concern is not only about the phone getting loose due to poor magnetic strenght, but the magnetic field interference with the phone functions.
Has anyone tested it yet?.
It looks pretty cool, as it is very small.
Link:
http://www.amazon.com/Tetrax-Magnetic-SmartPhones-iPhones-Players/dp/B0073X45RQ
Thanks.
I have used them for 6 or 7 months with my Motorola Razr in my car and on my golf trolley.
The system has a magnetic button that fixes to your car with a self adhesive pad, and there is a self adhesive plate to fix to your phone. These come in 3 sizes and I would recommend using the largest due to the weight of the S3
They have worked perfectly well, although my phone has occasionally fallen off the trolley when going over rough ground. I've never had a problem with it in the car.
I am not using it on my S3 because the metal piece that fixes to the phone will not let the S3 sit level on a desk, The Razr has a bulge at the top that I fixed the plate near to, so it was not a problem.
Thanks!
tetrax xway
Hi,
Please consider tetrax xway or fix way of any touch screen device like smgIII.
The x stabilize the unit when using touch screen, tubber for vibration absorption, better magenta strength.
Magnets do no interfere it's a patented opposite pole layout solution, more info here
tetrax.com/support/faq-frequently-asked-questions
thanks
stunno said:
I am not using it on my S3 because the metal piece that fixes to the phone will not let the S3 sit level on a desk, The Razr has a bulge at the top that I fixed the plate near to, so it was not a problem.
Click to expand...
Click to collapse
Thanks for that. The system does look good though, but I don't really want to have a bit stuck on my phone all the time. I'm thinking getting a second battery cover (when they are available!) might be a solution so that I can swap them when needed. Alternatively some kind of quick-snap piece for the phone that the metal part could be stuck to would be quite good.
Sent from my CM9 TouchPad
Isadora said:
Thanks for that. The system does look good though, but I don't really want to have a bit stuck on my phone all the time. I'm thinking getting a second battery cover (when they are available!) might be a solution so that I can swap them when needed. Alternatively some kind of quick-snap piece for the phone that the metal part could be stuck to would be quite good.
Sent from my CM9 TouchPad
Click to expand...
Click to collapse
You can get a replacement battery cover for the S3 here:
http://www.ebay.com/itm/11089202043...AX:IT&_trksid=p3984.m1423.l2649#ht_500wt_1361
My main concerns with the Tetrax holders are:
They clip to vent vanes, whish isn't always the most stable mounting solution.
You cannot rotate them to face the driver, which makes them not ideal for use with GPS.
almightywhacko said:
You can get a replacement battery cover for the S3 here:
http://www.ebay.com/itm/11089202043...AX:IT&_trksid=p3984.m1423.l2649#ht_500wt_1361
My main concerns with the Tetrax holders are:
They clip to vent vanes, whish isn't always the most stable mounting solution.
You cannot rotate them to face the driver, which makes them not ideal for use with GPS.
Click to expand...
Click to collapse
I know about these but I'd rather have one without the big "galaxy SIII" even if it's just for the car and I wouldn't actually see it
I was looking at the Fixway which doesn't clip to the air vent.
Sent from my CM9 TouchPad
FWIW, for the past couple of years I've used an alternative magnetic mount solution from krussell - most recently for the last 12 months with my SGS2
Despite some 'spirited' driving, its always remained perfectly secure.
I was worried about the magnetic field, but have had no such problems.
Its by far the best car mount solution I've ever used.
The magnetic disc is stuck wherever you want, and the thin metal plate is stuck to the back of your phone (or as I have done the back of the case)
http://www.amazon.co.uk/Krusell-Str.../dp/B000ORXUOM/ref=pd_luc_chashrec_02_01_t_lh
Now that I have my SGS3, I've ordered some cheap painted white self adhesive metal strips to attach to the SGS3 case to use with this magnet.
Ignore the poor 1* review from some plum who blames the product because he tried to use it with an ipod with a platter drive in it!
Watch the weight limitations on the FIX...
Isadora said:
I know about these but I'd rather have one without the big "galaxy SIII" even if it's just for the car and I wouldn't actually see it
I was looking at the Fixway which doesn't clip to the air vent.
Sent from my CM9 TouchPad
Click to expand...
Click to collapse
I wanted to get the FIX version as well, but the problem is that it only supports 150 grams or 5.25 ounces, and while the SGS3 by itself weight 4.7 ounces, when I add my Otterbox Defender, it brings it up to 7.4 ounces. So I guess the only options for me are GEO (air vent) or step up to the much pricier XWAY....

Dock that works with Draco Bumper

Hi, I was wondering if anybody knows if there are any docks that work with the draco bumper. I'm only asking because the draco bumper seems to be quite large. I've had to buy 3 different aux cords because they wouldn't fit, and I don't want to waste time trying out different docks.
You could always consider buying a 'universal dock' that clamps to the sides of the phone and then plug the phone in with a normal cable. It's not really a dock per say but it'll definitely do the job of holding your phone upright/horizontal.
If you need a link to one just let me know.
Aegishua said:
You could always consider buying a 'universal dock' that clamps to the sides of the phone and then plug the phone in with a normal cable. It's not really a dock per say but it'll definitely do the job of holding your phone upright/horizontal.
If you need a link to one just let me know.
Click to expand...
Click to collapse
Would you happen to know a car mount that would let me fit a S3 with the draco bumper and still let me use my camera while in place?
rlatjs17 said:
Would you happen to know a car mount that would let me fit a S3 with the draco bumper and still let me use my camera while in place?
Click to expand...
Click to collapse
http://www.amazon.com/gp/product/B008KP4ZFI/ref=oh_details_o02_s01_i00
I have been using that for a while. all my devices and my GF's devices have a the metal plate installed (and most, like the s3) have it under the battery door, so you cannot see it) and I have one for the car, and one for work. anywhere i go, with whatever i take, i can mount without looking. I also ziptied a cable to it, and am running a tasker script to start car mode (triggered by bluetooth to my alpine ex-10)
and yes, you can easily use the camera with it.
scarrmrcc said:
http://www.amazon.com/gp/product/B008KP4ZFI/ref=oh_details_o02_s01_i00
I have been using that for a while. all my devices and my GF's devices have a the metal plate installed (and most, like the s3) have it under the battery door, so you cannot see it) and I have one for the car, and one for work. anywhere i go, with whatever i take, i can mount without looking. I also ziptied a cable to it, and am running a tasker script to start car mode (triggered by bluetooth to my alpine ex-10)
and yes, you can easily use the camera with it.
Click to expand...
Click to collapse
Would this cancel NFC and if its a metal plate do you lose any reception? And how sturdy is it? I wouldn't want it falling off because of a few big bumps on the road, and I thought strong magnets aren't good for our phones.
rlatjs17 said:
Would this cancel NFC and if its a metal plate do you lose any reception? And how sturdy is it? I wouldn't want it falling off because of a few big bumps on the road, and I thought strong magnets aren't good for our phones.
Click to expand...
Click to collapse
I do not have a way to check the NFC cancelling...
there is no reception loss, as it is is as large the battery only, and the antenna is up top, away from the plate.
big bumps?
i live in central PA, and drive a car lowered on coilover suspension (and turned pretty tight too) and the phone has not budged an inch. perhaps i should do a review.. with the camera running during an autocorss and going over nasty bumps.
magnets mess up harddrives.. not phones.

Car holder whilst using a case

I'm after a car holder for my HTC One whereby I don't have to take the phone out of the case as it's annoying and I'd like something quick and easy to use.
I've bought a few from Amazon for my HTC One X but they were rubbish, flimsy or just didn't stick to the windscreen.
So I'm after some personal experiences too, has anyone bought a car holder for their One that you don't have to take it out of the case to use and does it work well?
Somewhere I can buy it from in the UK
Something like this I bought for my HOX but it just didn't work very well. Might give it a go since it's only £2.
My friends in the UK use this: http://www.amazon.co.uk/Mountek-nGr...e=UTF8&qid=1372679295&sr=8-1&keywords=Mountek
I just ordered one this morning and am expecting to receive it in a week to ten days since I am in Egypt. My friends have had it for a long time now and they tell me that it's amazing and the quality is extremely durable to this day.
Some of them also use a combination of two items: this and this. The first one has a sticky pad which is very, very strong and just doesn't fade, they tell me it's as strong as the day they bought it and they use the second item sometimes, basically they attach it to the sticky pad and use it as an actual car mount.
The second suggestion isn't the most practical but it works well and is fairly cheap, however the Mountek one is just perfect; not only did I read good reviews about it and was it recommended by friends, but I also watched videos and I find it great.
http://www.youtube.com/watch?v=kG3A4uq1ItQ
I can highly recommend this one…
http://www.mobilefun.co.uk/supergrip-universal-case-compatible-car-mount-p30552.htm
It will hold just about any phone in either portrait or landscape. Its suction pad even sticks to mottled, textured dashboard surfaces. Naturally it holds to glass like a limpet. Beware of the cheaper Amazon look-a-likes that have an inferior sucker.
It is very quick to attach and remove your phone, and doesn’t smother the phone’s back so the phone still gets air cooling (mine gets very hot charging and using sat nav). I think it looks ok too.
Thanks both, much appreciated. I'll check both of these out.
@wnp_79 - What's the pressure like on your car holder, in respect to it looks like it's spring loaded so I'm worried that it might put too much pressure on the sides of the phone, if that makes sense?
gibbs1984 said:
Thanks both, much appreciated. I'll check both of these out.
@wnp_79 - What's the pressure like on your car holder, in respect to it looks like it's spring loaded so I'm worried that it might put too much pressure on the sides of the phone, if that makes sense?
Click to expand...
Click to collapse
It is spring loaded, but does not hold the phone with any more pressure than you would use holding it yourself. The only issue I've had is with certain cases (like the Otterbox Commuter) which have protruding volume buttons. The grip is enough to accidentally activate these if you are not careful where you place the phone. With flush buttons or ensuring the grip misses them there's no issues.
wnp_79 said:
It is spring loaded, but does not hold the phone with any more pressure than you would use holding it yourself. The only issue I've had is with certain cases (like the Otterbox Commuter) which have protruding volume buttons. The grip is enough to accidentally activate these if you are not careful where you place the phone. With flush buttons or ensuring the grip misses them there's no issues.
Click to expand...
Click to collapse
Thanks, I'll add it to the possible list and I'll do some more research before pay day.
Appreciate the feedback
wnp_79 said:
I can highly recommend this one…
http://www.mobilefun.co.uk/supergrip-universal-case-compatible-car-mount-p30552.htm
It will hold just about any phone in either portrait or landscape. Its suction pad even sticks to mottled, textured dashboard surfaces. Naturally it holds to glass like a limpet. Beware of the cheaper Amazon look-a-likes that have an inferior sucker.
It is very quick to attach and remove your phone, and doesn’t smother the phone’s back so the phone still gets air cooling (mine gets very hot charging and using sat nav). I think it looks ok too.
Click to expand...
Click to collapse
Yes this one works wonderfully. I thought it a little to simple at first... But simple wins here. It'll even work with future phones. You can install and remove phone one handed and of course cases work. Only bad thing is no dedicated charging... But i got over that quick.
Kenu airframe. For me it's the best.
Sent from my HTC One using Tapatalk 4 Beta
I've been looking for the same thing. Thanks for the recommendations, I will report back once I pick one up!

[Q] Magnetic fridge mount?

I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Super Sam Galaxy said:
I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Click to expand...
Click to collapse
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
jimmbomb said:
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
Click to expand...
Click to collapse
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
jimmbomb said:
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
I do like the fact that your way doesn't involve destroying parts of my kitchen! I'm thinking now that if I find a way to fasten the USB cable to the fridge in a semi-permanent manner it may not be so bad... The cord is white, like the fridge, and with it being flat it may be less noticeable. I wonder how it would hold up with the door being open and closed, as in whether or not it would slide/fall from the repeated movement... This is going to be a tougher decision than I initially thought! At least there's time to figure it out, the tablet won't be here for like 2 months.
Click to expand...
Click to collapse
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
jimmbomb said:
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
Click to expand...
Click to collapse
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
UPDATE: Just got off the phone with TWC after an hour and 36 minutes, and they told me that they are going to "pass my details to the correct department" and I'd get a call within "3-4 days". Funny, as I pointed out, that was the same thing they told me 8 days ago, after another equally long phone conversation. Anyway, to sum it up they are giving me a credit equal in value to the tablet and I'm debating between the Galaxy Tab 3 (7 inch), which was what the promotion originally offered, or the 2013 Nexus 7. The Nexus has gotten great reviews, is there anything about the Galaxy Tab that you'd recommend over the Nexus? I know I'm kind of getting off track here but I'm just curious.
Super Sam Galaxy said:
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
Click to expand...
Click to collapse
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Perhaps upload to Youtube and send a link? Anyway, don't worry about it if it's a bother, but if you get a chance I'd be interested to see. I'll try to keep up with the thread better!
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Super Sam Galaxy said:
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Click to expand...
Click to collapse
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
jimmbomb said:
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
Click to expand...
Click to collapse
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Super Sam Galaxy said:
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Click to expand...
Click to collapse
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
jimmbomb said:
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
Click to expand...
Click to collapse
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Super Sam Galaxy said:
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Click to expand...
Click to collapse
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
jimmbomb said:
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
Click to expand...
Click to collapse
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Super Sam Galaxy said:
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Click to expand...
Click to collapse
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
jimmbomb said:
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
Click to expand...
Click to collapse
Thanks!
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Latheman said:
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I agree that removable storage is nice, but I wouldn't say it's a deal breaker for me because of the fact that I can get something like a Meenova to easily add more storage if I need to. At this point I'm leaning toward the Nexus because for this purpose, wireless charging capability seems more beneficial than removable storage simply due to the fact that it would be cool to not have a cord showing when it's mounted, and to not have to plug it/unplug it every time I want to take it down for a bit. Of course, the flip side is that instead of seeing a cord, I'd see the Meenova sticking out of it, but that doesn't seem as bad since I probably wouldn't need to have one in there all the time. Either way, I do appreciate the suggestion and I will certainly take into account the capability for removable storage when making my choice. Thanks!

Why doesn't this case exist?

I've spent the better part of the week scouring for good s8+ cases that would be compatible with wireless charging and in the end I've hodge podged pieces into a frankencase
seeing as I'm probably going to make myself a case I thought I'd share the elements of what I was looking for and ask if I'm just crazy for wanting so much or if I'm not alone.
I don't need much coverage, mostly the corners and a raised edge in case it does fall but otherwise I'm not concerned with protecting the fronts and backs given how rarely I drop my phone if I've got an actual grip on it no thanks to the slippery materials they use
I'd like direct access to my buttons, many cases have their own button that pushes the actual button, I've never enjoyed this as it's usually stiff or hard to press and often hard to distinguish from the case itself
wireless compatibility is a must for me given the fact I'm not only on the road most of the day but I'm constantly in and out of the vehicle where I'm definitely not leaving my phone that I'll probably actually need, and having to work a harness gets annoying during regular use imagine 30+ times a day
this means something magnetic so it sticks in place like the airdock 2 which I have no idea if it's compatible with s8+ or not as of yet
getting back to the in and out I need a hip holster because I spend way more time texting and taking photos of job sites than talking so a headset is less important than not having to fish for my phone
lanyards are just good ideas, why is it so rare to find them let alone on a rugged case?
a kickstand doesn't have to be complicated either and doesn't need an entire phone length if you know what you're doing with it, spigeon has a nice stick on that generally gets the job done, or even those ring mounts double as kickstands and great dash magnet mounts
who puts a card holder behind the case right in the magnetic field of wireless charging? it's called a folio cover geez, even those work as kickstands in a pinch as flimsy as they are in that capacity.
granted with all the mobile payment options these days you generally don't need to worry about a card in the first place so it's coming time to uncouple those two
and on a side rant why are we still using adapters and converters for magnetic break away cables? shouldn't this be standardized by now?
I'm going to sketch up the case I'm thinking of and post back maybe you guys can tell me why it's such a ridiculous idea to have.
I wanted the equivalent of an iBolt with a wireless charger in the end I wireless charge at home and use a magnetic power connector on the car.
All the ones I found only gave portrait and I preferred to use landscape
What car charger are you using?
Sent from my SM-G955F using Tapatalk
Tonesav said:
I wanted the equivalent of an iBolt with a wireless charger in the end I wireless charge at home and use a magnetic power connector on the car.
All the ones I found only gave portrait and I preferred to use landscape
What car charger are you using?
Sent from my SM-G955F using Tapatalk
Click to expand...
Click to collapse
I'm looking to buy still, just got my s8+ a couple weeks ago, with the unveiling of the note8 I almost took it back
as of right now for in the car I'm using https://www.amazon.com/BESTEK-300W-Power-Inverter-Adapter/dp/B004MDXS0U/ with cables
not sure I want to have to add in something to a case to make it compatible I'd rather the case be compatible to begin with, many magnetic chargers work just fine without add ins
https://docs.google.com/drawings/d/10wBkiHyNDZF969vzCDtKLQ8TI5XLnB5wJ3GOLJJhA-8/edit?usp=sharing
basically just imagine some time on the dremel to cut out everything covering up the back as much as possible except maybe leaving a bit near the edges
if I have the ring it'll be near the power button
and the kickstand will be probably above the camera or down by the fcc text, very small chance I do it vertical by the bixby button
pair it with a belt clip, and maybe something like a folio cover under the screws if I do feel like having cards
if I can do this with existing parts and a dremel why can't one of these case makers?
I'm trying to figure out how I would do a swivel like the ring but with something as long as a kickstand for more angle options, found one custom stent on a case that could work, not sure yet if that's how I want to do it?
figured it out, answer is no kickstand, there's 3 places I legit need a kickstand and I can just get stands and put them there
apparently there isn't much of a phone case modding scene I can find.... does everyone just live with the cases they buy? can't everything be improved with some ingenuity?
My new case, ticks most of the boxes
https://www.amazon.co.uk/XOOMZ-Detachable-Blocking-Magnetic-Leather-Brown/dp/B073QJ1N8P
biotoxin said:
I've spent the better part of the week scouring for good s8+ cases that would be compatible with wireless charging and in the end I've hodge podged pieces into a frankencase
seeing as I'm probably going to make myself a case I thought I'd share the elements of what I was looking for and ask if I'm just crazy for wanting so much or if I'm not alone.
I don't need much coverage, mostly the corners and a raised edge in case it does fall but otherwise I'm not concerned with protecting the fronts and backs given how rarely I drop my phone if I've got an actual grip on it no thanks to the slippery materials they use
I'd like direct access to my buttons, many cases have their own button that pushes the actual button, I've never enjoyed this as it's usually stiff or hard to press and often hard to distinguish from the case itself
wireless compatibility is a must for me given the fact I'm not only on the road most of the day but I'm constantly in and out of the vehicle where I'm definitely not leaving my phone that I'll probably actually need, and having to work a harness gets annoying during regular use imagine 30+ times a day
this means something magnetic so it sticks in place like the airdock 2 which I have no idea if it's compatible with s8+ or not as of yet
getting back to the in and out I need a hip holster because I spend way more time texting and taking photos of job sites than talking so a headset is less important than not having to fish for my phone
lanyards are just good ideas, why is it so rare to find them let alone on a rugged case?
a kickstand doesn't have to be complicated either and doesn't need an entire phone length if you know what you're doing with it, spigeon has a nice stick on that generally gets the job done, or even those ring mounts double as kickstands and great dash magnet mounts
who puts a card holder behind the case right in the magnetic field of wireless charging? it's called a folio cover geez, even those work as kickstands in a pinch as flimsy as they are in that capacity.
granted with all the mobile payment options these days you generally don't need to worry about a card in the first place so it's coming time to uncouple those two
and on a side rant why are we still using adapters and converters for magnetic break away cables? shouldn't this be standardized by now?
I'm going to sketch up the case I'm thinking of and post back maybe you guys can tell me why it's such a ridiculous idea to have.
Click to expand...
Click to collapse

Categories

Resources