Develop Bugs

My universal is a brick!

Hello everyone, my first experience of upgrading the firmware is sadly failed and now my beloved m5000 is only a beautiful paperweight!!!
No key combination could start the bootloader nor soft or hard reset works.
When I connect it to mains charger, the right led goes red for few seconds and then goes off...
In the service manual I have read that this signal means hardware failure but because the fault is the consequence of a failed upgrade I don't thing that it is really broken.
I already tried to contact htc and orange for repairing but in Italy where I live it seems that the warranty isn't valid and services are very scarce.
Someone have an hint?
Thanks.

Try to do a hard reset, many manage to get that white screen.

Thank you for the suggestion but it doesn't work The phone is completely dead, except for the red led. Any key combination including hard reset simply doesn't work.
I suspect that the only way to resurrect it is to reflash using a jtag interface.
But unluckily I don't own the pinout!!!

take a look here: http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen for instructions on how to use the mtty utility to bring your device "back to life"
There's additional information on the mtty utility in this thread: http://forum.xda-developers.com/showthread.php?t=259003
hope this helps

If you are on the bootloader menu...
Try to flash again a complete rom + extended rom + Radio
SOmetimes it can work again

sigh... thanks to everyone but I can't reach the bootloader menu: the uni is bricked!
My only hope is to find the jtag pinout...

Try holding down Light + power for at least 5sec. and while still pressing, do a soft reset.
If you dont go to BootLoader then try to increase the Hold down Light + Power some more.
This worked for me, could again get it active on usb and ran my original rom upgrade while it was in BootLoader mode.
If that dossent work, try the bootloader upgrade version at
http://wiki.xda-developers.com/inde...tion On How To Upgrade with Bootloader method
You can do the same with the two - - buttons, holding for more than 5sec. then soft reset. Should bring up the Reset with 0 or X to cancel.
But it just reverted to a brick every time for me with this.

BTW. do this with USB or Power Cable plugged in!!

another possibility is that your battery is low enough not to allow booting but is still able to light up the LED. it happened to me a few times that i was thinking it was completely gone and it was just low bat. remember that if you have a non booting device it may not even charge the battery anymore so you'd better ask a friend to lend you a charged one, just to be sure.
cheers!

Ill Buy The Brick!
au$200.00 in your paypal account upon a sale +50 to Australia.
Let me know...
Simon

Still Charging
I have 2 wizards and a universal... By mistake, i have tried to upgrade the G3 wizard but pluged the G4!!!!!...... So now i have abricked G4 wizard. Now when i plug the G4 it does NOTHING, it is completly dead, BUT is still charging the Battery!!!! I am sure of this because i have tested the battery in the other device.. So try the same on universal plug it in and wait a few hours it may charge the battery.

anyway, if you can't unbrick it, do me me know if u're selling it.
need some spare parts.

Suggestion
What you can also try is remove Activesync from your desktop, Restart your desktop, install Activesync again and connect your device.
It's word a try! Has something to with rapi.dll!
Cheers...
Leo

My failure...
Hello everyone, I've tried all yours suggestion one by one and step by step but without success.
My last chance to not consider this phone a complete loss is to sell it as spares/repair...
Does someone is interested?
P.S.: notwithstanding the phone is bricked it still charge the battery

Try holding the the two - softkeyes for longer/shorter time before you softreset while still holding them down.
Also try different intervals with the softbuttons while holding the Power + Light down, also with soft+Light & soft+power & power+light
all with different intervals.
Look closely at the screen after each try, to se if it goes to bootloader mode.
And remove SD card and Sim also.

I Hate Bootloader!
I have tried ALL of these power+light+reset suggestions and I STILL can't get into the damn bootloader menu! I just gave up and rip apart my JasJar every time I want to update it. For some reason the only way I can access this menu is by pulling the main battery and disconnecting the smaller(watch battery) one in the upper right hand corner and letting it sit for a couple of hours.
Come to think of it, when I use even the factory updates I don't even get a report on the update screen telling me what my current config is! So then I hit update anyway, the unit turns off, I lose my USB connection, it no longer charges, and I have to take the battery out. Almost like the PROGRAM can't even get it into the loader! This is probably how I learned to just yank the batteries when I want to upload.
Unless there is something different because I have an earlier model... I have no clue. Does the unit need to be running or something when I do this? I think this is a fairly elementary task but it just doesn't work. Has this happened to anyone else?
Yes, all my buttons are in working order = )
BTW after my last tear-down I have -
Bootloader: 1.01
Rom version: Ivan-2.60.00WWE
Rom date: 12/20/06
Radio version:1.14.00
ExtRom version: Modified

http://forum.xda-developers.com/showthread.php?t=247440&page=14 I think someone already suggested this, but just in case...

No chances
Well, today I've verified my battery and it works like a charm in the uni of a friend. Then the last possibility is gone.
Someone knows how to go ahead any further?

Phone bricked, unbricking TUT not working.

I was updating my Dash the other day to Ookba's latest rom when I received an error message. It gave me instructions on how to fix it (loading it in bootloader etc.), and I received a message saying it was successful and the rom would continue updating. I received another error message saying the rom was corrupt, and the program shutdown. My phone will not power up now. It was at(or near) full charge while reflashing, but will not turn on regardless of the button combination I hold while attempting to power it on.
Any ideas? Thanks!

what rom did you attempt to load in the bootloader? it should have been the factory rom..if not, then that is probably the root of the problem....as far as it not powering on now...I leave that open to the forum...cuz' I have no relevant advice on that one....

when trying to do the gold card method to unbrick my phone, it say Invalid certificate ..? wats this and how to fix it.

I was trying the "[ROM][EXCA][WWE][* 3VOLUTION SERIES *][WM6.5 STD 21854][Build 3VO.3.00.112509]" when it locked up on me, and still hasn't been able to power up.
Today when plugging it in after a week of letting sit, a red led light showed where the normal orange/green led would normally light up when charging/charged. The light stayed on for a few seconds, then shut off. Nothing else though. Any other suggestions?

allthrottle said:
I was trying the "[ROM][EXCA][WWE][* 3VOLUTION SERIES *][WM6.5 STD 21854][Build 3VO.3.00.112509]" when it locked up on me, and still hasn't been able to power up.
Today when plugging it in after a week of letting sit, a red led light showed where the normal orange/green led would normally light up when charging/charged. The light stayed on for a few seconds, then shut off. Nothing else though. Any other suggestions?
Click to expand...
Click to collapse
Red light my friend means your battery is gone, probably your phone is not bricked maybe it just needs a battery replacement

I am having the same issue, except that I can place the battery in another Dash and it boots up just fine, so I am assuming it is not the battery. I will buy another one to double check. My problem is the same as which is stated above. Can anyone help? Thank you.

Just an update to see if I can get anymore suggestions. Hadn't touched the phone since the last post. Bought a new battery for it this weekend and it's still dead as ever. Won't boot at all. Not into bootloader, nothing. I get absolutely no response holding power+cam or softkeys+power.
Any advice? I don't absolutely need the phone as I've picked up a G1, but it would be nice to have this working, or at least trash it if it's junk.
Thanks!

Everyone else stumped too?

Have you connected to the wall charger to see if you get some response with your new battery?.

Just unbricked mine after being dropped again by the girlfriend. Try this, plus usb cable into device, press the camera button only. See if that gets you into the bootloader screen. If so, flash the oem build and go from there.

Tried it plugged into a wall charger for 3-4 hours, car charger for another hour, and computer/usb for another hour. No response anytime.
I'll try the camera only method when I get home later.
Thanks!

Just tried plugging it into the computer and holding only the camera. Didn't work. Tried that, tried holding power+cam, power+soft keys etc.. What's weird is I had the battery cover off while doing this, and the battery slipped out while I was holding cam+pwr, it actually loaded into the multicolor(bootloader?) screen twice, but would shutoff within a few seconds. Now I'm back to no response from it.

Finally got it to stay on the boot screen without turning off, but can't get it to establish an activesync with the computer so I can't flash it. The computer is obviously detecting it though, because I see an icon that says "remove smartphone usb sync".

The phone's FINALLY working again! Thanks again guys! I was a couple of days away from junking the thing! I couldn't get Ookba's rom to flash it, so I went back to the unbricking tutorial and saw that he recommended grabbing the factory rom to flash it. I did, it worked, and I just flashed it again using Ookba's rom.
Took quite a few months, but it's back! Thanks!

Stuck in downloadmode, Screen off, tablet won't respond, explanation inside

So, after flashing the latest firmware from sammobile for the Galaxy Tab S 10.5 with Odin, I am now the not-so-proud owner of a what seems to be unresponsive - working - device.
Let me explain:
I just downloaded the latest firmware from sammobile.
I followed the instructions from sammobile, which basically says normal flash with Odin.
Plugged it in, started Odin, put the file in the right place and started the flash.
Odin does its thing, everything goes well, device is showing me a nice blue dotted bar which is filling up slowly, good.
And then suddenly Odin reports "FAILED" after is was done with /system.
Device has stopped working, blue bar not filling anymore.
I reset Odin with hope to restart the flash, with no result.
The device is not being recognized anymore by USB, and it's now stuck in the "odin mode" screen.
After seeking some advice on IRC I found that the only way to get the power off is to unplug the battery, which is harder that it sounds.
So after a good 30 minutes of carefully prying and making my way around the tablet I managed to get the cover of.
As I'm looking at the naked device and wondering "how the hell do i get this battery out". This is not like a normal phone or laptop or any kind.
I found a couple of little screws, 4 of them, around the battery so I unscrewed these and the battery came 'loose' but was held in place by 2 flat cables which I couldn't remove.
Put them back in, and all of a sudden my tablet's sceen was 'off', but I'm not sure it's really powered off because the powerbutton has no response.
I'm stuck and it the thought of just binning the tablet is frustrating me.
Anybody got any ideas of what this might be and how to fix it?
[edit]
I found out it wasn't powered off, it was just the screen. I could feel the CPU was still emitting heat.
So I unplugged the battery, let it cool down for a couple of minutes, plugged it back in, and now there is nothing.
No screen, no usb recognition, no power.
Any suggestions are appreciated.

You didnt need to take out the battery. Your should have exit download mode by doing power, home, vol down buttons for 30 seconds and it should reboot and you could of tryed again. If that didnt work you could have let it drain. Im not sure about helping with the battery part as i never opened it.

easy fix - check http://forum.xda-developers.com/showpost.php?p=50412284&postcount=8
no need for draining the battery. tested and it works. happens once to me, use above method and problem solved.
can use my modded version attached, but, please be aware, it's ONLY FOR RESETTING THE STUCK DOWNLOAD MODE !

DUHAsianSKILLZ said:
You didnt need to take out the battery. Your should have exit download mode by doing power, home, vol down buttons for 30 seconds and it should reboot and you could of tryed again. If that didnt work you could have let it drain. Im not sure about helping with the battery part as i never opened it.
Click to expand...
Click to collapse
I tried that, but didn't work. The tablet was/is unresponsive. Draining wasn't an option, battery was just fully charged.
freaksamael said:
easy fix - check http://forum.xda-developers.com/showpost.php?p=50412284&postcount=8
no need for draining the battery. tested and it works. happens once to me, use above method and problem solved.
can use my modded version attached, but, please be aware, it's ONLY FOR RESETTING THE STUCK DOWNLOAD MODE !
Click to expand...
Click to collapse
Thanks for this! Am going to try this once my screen works again.
At this point it goes 'on' but the screen doesn't, and there is still no USB recognition so I guess I got a nice expensive paperweight

[Q] SM-T700 Froze, Powered off - Soft bricked?

Hey guys,
Appreciate it if you could spare me some advice on how to proceed.
So I was watching a twitch stream and all of the sudden tablet froze, and the audio froze as well causing a large super high pitch noise, I hard-reset the tablet but instead of resetting it just turned off, I started to browse the forums and found that a combination of (POWER + VOL UP & DOWN + HOME) would reset the tablet,now what this did for me is turn the tablet on but it was stuck in SD CARD Mode, back again to the forums, read that letting it discharge fully and then it will be able to be charged and turned on, that worked tablet was back doing some various tasks no video again and then boom freezes again same symptoms except this time I couldn't get it to go to SD CARD Mode its very finicky after trying at various times in the day I finally got it to work, same process except this time as soon as it turned on I went into recovery factory reset it to stock, worked a bit longer this time only installed chrome, and it froze again (don't think it was chrome) , rinse repeat and I flashed the latest firmware with ODIN worked fine, I've gotten to the home screen ran through the "factory new" set up and it turned off of me again.
I plugged it in let it charge, came up with battery icon 5% 10% ect, then I left it for a while, I came back and I cant even get it to show the battery percentage(tap power) let alone turn on.
I'm fairly sure that eventually I can get it turn back on but from there I don't know what to do.
TL;DR - Tablet Froze, Hard Reset, Froze again - Rinse Repeat, ODIN to latest STOCK firmware, tablet worked for 5 min before turning off again (plugged in), present situation
Any ideas as what to be causing the freezing and how I could remedy it?
Also sometimes when it froze it turned itself off without me hard resetting it.
Thanks its been driving me insane,
Please do not hesitate to ask me to clarify or provide more information so I can help you help me.

Maybe youve got the loose battery connector problem?

ashyx said:
Maybe youve got the loose battery connector problem?
Click to expand...
Click to collapse
What would you suggest I do, submit it to warranty ? Will they disregard the fact that knox has been tripped if its a hardware issue ?

sunb3ar said:
What would you suggest I do, submit it to warranty ? Will they disregard the fact that knox has been tripped if its a hardware issue ?
Click to expand...
Click to collapse
I had the loose battery connector problem, but the symptoms do not sound the same as mine. I could get mine to boot up, but the screen would flicker and a few white lines would appear before it would reboot itself. I actually started a ticket with Samsung and got the packaging label but, upon further reading, realized that I was pretty much SOL after tripping knox, and didn't want to risk the chance of getting charged for just sending it in. If it is indeed the loose battery connector, you should be able to remove the back cover yourself and fiddle with it. Ultimately, mine needed re-soldering, and I was able to find a local electronic repair shop to do it for me for cheap.
Good luck!

UPDATE: I've managed to get into SDCARD MODE yet again, except discharging seems to get out of it, but once I plug it back in it doesn't come up charging it just black screen, until I hold some buttons and arrive back at sdcard mode. Good times.
Trying various things to get it to boot..
EDIT: Appreciate the insight Squez, I want to exhaust all the other options before opening it myself, if Knox didn't void the warranty to some degree, opening it up should put the final nail in the coffin.
EDIT2: Good news, sort of, tablet isn't dead! after numerous attempts with charge SDCARD mode, discharge, It finally start to charge properly and I managed to get it to boot, worked for a few hours then I left it to charge, and went to sleep, woke up and wont turn on again, but I am in SDCARD Mode again but need wait for it to discharge from presumably 100% ....

[What do you mean Sd card mode? DOWNLOAD mode?
Also no need to let the battery drain.
Just press VOLUME DOWN(not volume up) and POWER together then hold until it restarts.
This is a hard reset and will ALWAYS work unless the device is hard bricked. It is the equivalent of a battery pull.
I continually see here and there incorrect information regarding key combinations, even in so called guides, this forum is even guilty!
Here is what works on the 10.5lte, as far as I'm aware its the same for all versions, indeed pretty much any Samsung device.
HARD RESET:
VOLUME DOWN - POWER.
Hold until the device restarts.
DOWNLOAD MODE:
HOME - VOLUME DOWN - POWER.
Hold until the device boots.
RECOVERY MODE:
HOME - VOLUME UP - POWER.
Hold until the device boots.

ashyx said:
[What do you mean Sd card mode? DOWNLOAD mode?
Also no need to let the battery drain.
Just press VOLUME DOWN(not volume up) and POWER together then hold until it restarts.
This is a hard reset and will ALWAYS work unless the device is hard bricked. It is the equivalent of a battery pull.
I continually see here and there incorrect information regarding key combinations, even in so called guides, this forum is even guilty!
Here is what works on the 10.5lte, as far as I'm aware its the same for all versions, indeed pretty much any Samsung device.
HARD RESET:
VOLUME DOWN - POWER.
Hold until the device restarts.
DOWNLOAD MODE:
HOME - VOLUME DOWN - POWER.
Hold until the device boots.
RECOVERY MODE:
HOME - VOLUME UP - POWER.
Hold until the device boots.
Click to expand...
Click to collapse
I should of posted a photo earlier but here is one I found on google of same screen: (check attachments)
Except UP KEY and DOWN KEY don't do anything, its just this screen, if you attempt to hard reset ect, it will just reload this screen, hence the discharge, then plug it back in and hope it begins to charge "battery icon appears". I have gotten it to boot like this a few times.

sunb3ar said:
I should of posted a photo earlier but here is one I found on google of same screen: (check attachments)
Except UP KEY and DOWN KEY don't do anything, its just this screen, if you attempt to hard reset ect, it will just reload this screen, hence the discharge, then plug it back in and hope it begins to charge "battery icon appears". I have gotten it to boot like this a few times.
Click to expand...
Click to collapse
Wtf
How did you get to that mode? Looks like its trying to flash from the sd card. Ive seen safe mode but not that.
see here: http://forum.gsmhosting.com/vbb/10127092-post62.html

ashyx said:
Wtf
How did you get to that mode? Looks like its trying to flash from the sd card. Ive seen safe mode but not that.
see here: #
Click to expand...
Click to collapse
Yeah its strange as.
I'll have a look at that, thanks.
EDIT: It just finished discharging and now I am on the battery screen.. Usually once it charges here I can get it to boot, what I'm curious is what on earth keeps causing it to freeze up, because in download mode and twrp (gone since i flashed stock via odin) it wouldn't freeze at all, only have issues with it once its booted or charging. I installed a logcat earlier hopefully that should shed some light on the situation,
EDIT2: Well another very interesting thing, the official Samsung charger wont charge it, only works if I plug it into pc or use a non-official charger, strange thing is nothing is wrong with the samsung charger or cable since I can charge my phone fully from it. These have to be some of the strangest symptoms.
EDIT3: Only works through USB port on PC for now, non official charger comes with red X on battery once booted. I assume you can work around this once rooted but that's for another time..
EDIT4: Charge through pc to around 2-3%, boot device, plug into official samsung wall charger and it begins to charge properly.
EDIT5: Hooray back to step one, trying get into SDCARD Mode, same thing happened left it overnight and it wont turn on or charge anymore.

ashyx said:
Wtf
How did you get to that mode? Looks like its trying to flash from the sd card. Ive seen safe mode but not that.
Click to expand...
Click to collapse
i am pretty sure the HOME - VOLUME DOWN - POWER. puts the 10.5 into the sdcard mode.
my tablet is doing very similar to sunb3ar findings.
have had it come back to me once from sdcardmode.. (let if go flat and starting charging then it would start via normal buttons)
it crashed not long after that. it got stuck in sdcard mode again, but this time none of the drain flat, put on charge has worked.. just blank..
fyi- we try to put it in RECOVERY MODE, but it does not work when in this crashed / sdcard mode state
i even disconnected the battery and then plugged back on charge.. nothing..
today i tested the battery volts, 2.8v , for a 3.8v i thought that was ok. i attached my RC lipo multi charger set to 1amp 3.7volt charge, direct to the - + on the battery- got it up to 3.5v, plugged back in, put the charger on- the sdcard mode (most life it has shown in a week).
still not coming up with 'battery' display to say its 'turn-off and being charged'. just the sdcardmode might disappear and return..
i am currently adding mode charge to battery... will try to HARD RESET next.. since i have not tried that combo yet..
HARD RESET:
VOLUME DOWN - POWER.
Hold until the device restarts.
edit: i took it off 'direct' charge, battery at 3.7volts.. then plugged in normal charger, i got a 'battery symbol' but it had the lightening bolt, not a %.. so i unplugged and reconnected to my direct charge to give the battery more volts. i am surprised that the unit seems to think a battery with 3.8volt as it specs seems to not be like with volts not much lower than 3.8.. could be time for a new battery if we can get this thing to restart

Weird bricked GT-I9195 stuck on black screen after Samsung logo

So, unluckily today i find myself here lookin' for help with my phone. I had already took a look on other brick threads, but i can't find an appropriate answer to my problem.
I'm (i was) running lineage-14.1-20170602-nightly, i had ne0zone75's TWRP 3.1.0.0-0, and that's how the brick came in a strange way; i was simply on XDA Labs app browsing the forum, when i received a call. I've answered, and when i shut off the call the phone shut off immediately after. I thought it was a reboot, but keeping pressed the power button didn't switched on the phone anymore. So i've tried to remove the battery and re insert it after some minutes, but the only thing i can get is the screen with the samsung logo that goes all black after 5 seconds. I already had other bricks due some errors of mine in the past, but this time it's really difficult.
1: I can't access recovery mode. Ow, how i wish i could.
2: I can access download mode, but after that i reach the ODIN MODE screen with the details of product binary, KNOX, ecc. the phone shuts off again.
3: If i keep the power button pressed, the phone doesn't starts. It only starts if i replug the battery in, but after some seconds it shuts off again.
4: How could a call as another mess up the whole phone?
5: I didn't installed nothing new from at least a week... yesterday an automatic update of the Play Store took place, but except that nothing has been changed. Nothing of nothing! No settings, no apps...
What could i do? Installing Kies with Samsung drivers could help me flashing a stock rom for example? Because at the moment, there isn't too much that i can do with the phone in this state... I hope this little jewel won't have to become a stone to be thrown away. Any help would be great, and really appreciated. Thanks in advance...

Things has got worse. Now my device doesn't starts at all; no vibrations, no signs of life, nothing. I've tried even to put it for 6 hours in my refrigerator, because i've read that the cold temperature could be helpful to fix some broken contacts on some component, but i'm losing hope 'bout it. I supposed that at this point is something hardware-based and not software, because it's just impossible that a call like an other one could be the cause of this hard brick... The only thing is that if connected to my PC, it is being showed as QHSUSB_LOAD. I'll try some methods that i've seen in other forums, like softwares that tries to fix this, but i think that i'll be forced to buy a new device. Neither an usb-jig could help me to force the download mode if the phone is dead in every aspect... the only thing that i still didn't understood, is if a debrick.img on my SD card (sadly i've read that a microSD class 10 with at least 16 GB is required, and i don't have one) could help somehow on a situation like this one of not. Still no one could advice me with some tip, guys
Edit - feel free to close this thread, I have another phone now