Develop Bugs

Need help with XDA Orbit

Hi Guys,
I'm a noobie and need help with the orbit.
I tried updating to the orbit_WM6 which I downloaded from rapidshare. It said if the rom update freezes then you stop it by resetting the xda. I did this but now the xda doesn't seem to be going passed the screen where it gives you the information "IPL 3.04.0001 etc". When connected to the laptop it's not picked up by the computer!!
What shall I do? I haven't bricked it have I?
Thanks for the help in advance

Not flashed properly dude...reflash it again...Btw, are u able to invoke your phone to boot loader mode...

earthwind3 said:
Not flashed properly dude...reflash it again...Btw, are u able to invoke your phone to boot loader mode...
Click to expand...
Click to collapse
When I connect it to the computer it doesn't recognise it so how can I reflash it?
I can get to the bootloader.
The information I get on the carrier screen (02 Welcome) is as follows:
IPL 3.04.0001
SPL 3.04.0000
GSM 03.06.90
OS 3.4.0.0
Please can someone give me some step by step instructions?

If I try using start_uspl I get an error 'No device connected' and it says 'Can't spawn "cmd.exe": No such file....'. It fails at line 69 and then completly stops at 81.
Any advice?

earthwind3 said:
Not flashed properly dude...reflash it again...Btw, are u able to invoke your phone to boot loader mode...
Click to expand...
Click to collapse
I've managed to get to the bootloader where it say's 'RUU' in the top right corner. What can I do next guys?

s4 mini wont turn on

hi, can anyone help me out i broke my s4 mini screen, iv just replaced the screen and digitizer and also charge port at bottom after breaking it taking phone apart. All worked fine for about 10 mins then the screen went blue an alarm sound was going off for about 5 mins then it shut off, now it just will not turn on at all it goes straight to odin and says th following:
COULD NOT DO NORMAL BOOT.
ODIN MODE
PRODUCT NAME:GT-I9195
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
KNOX KERNAL LOCK:0X0
KNOX WARRANTY VOID:0X1
CSB-CONFIG-LSB 0X30
BOOTLOADER AP SWERV:1
WAITE PROTECTION ENABLE
anyone help me out on this please? what do i do?

1990dtl said:
hi, can anyone help me out i broke my s4 mini screen, iv just replaced the screen and digitizer and also charge port at bottom after breaking it taking phone apart. All worked fine for about 10 mins then the screen went blue an alarm sound was going off for about 5 mins then it shut off, now it just will not turn on at all it goes straight to odin and says th following:
COULD NOT DO NORMAL BOOT.
ODIN MODE
PRODUCT NAME:GT-I9195
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
KNOX KERNAL LOCK:0X0
KNOX WARRANTY VOID:0X1
CSB-CONFIG-LSB 0X30
BOOTLOADER AP SWERV:1
WAITE PROTECTION ENABLE
anyone help me out on this please? what do i do?
Click to expand...
Click to collapse
try my unbrick guide in the s4 mini general forum
but first check if the connection to the screen is really proper

1990dtl said:
hi, can anyone help me out i broke my s4 mini screen, iv just replaced the screen and digitizer and also charge port at bottom after breaking it taking phone apart. All worked fine for about 10 mins then the screen went blue an alarm sound was going off for about 5 mins then it shut off, now it just will not turn on at all it goes straight to odin and says th following:
COULD NOT DO NORMAL BOOT.
ODIN MODE
PRODUCT NAME:GT-I9195
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
KNOX KERNAL LOCK:0X0
KNOX WARRANTY VOID:0X1
CSB-CONFIG-LSB 0X30
BOOTLOADER AP SWERV:1
WAITE PROTECTION ENABLE
anyone help me out on this please? what do i do?
Click to expand...
Click to collapse
flash stock rom with Odin and full wipe

Aronuser said:
try my unbrick guide in the s4 mini general forum
but first check if the connection to the screen is really proper
Click to expand...
Click to collapse
Hi thanks for reply what do you mean check connection to screen is really proper?

gonzalomorenorovetto said:
flash stock rom with Odin and full wipe
Click to expand...
Click to collapse
where do i get roms i downloaded one but it just said failed on odin so duno if it just wont work or the file was dodgy took me 2 hours just to find a website with a rom dont really know what im doing with that side of it to be honest

Aronuser said:
try my unbrick guide in the s4 mini general forum
but first check if the connection to the screen is really proper
Click to expand...
Click to collapse
hi your post on unbricking says
Bootloader > BOOTLOADER...
PDA > CODE...
PHONE > MODEM...
CSC > CSC...
PIT > CSB..
but my odin has
bootloader
ap
cp
csc instead of pda and phone so not sure where to put the files

ahhh success thankyou very much took 4 times flashing with odin before phone actually stayed on kept shutting down again what can i do to stop it happening again what is all this twrp and custom roms?

Died again was working then took battery out to put sim card in tried unbricking again no luck just says recovery booting.......set kernal bit grrrr

Have you ever managed to get that fixed? I'm having the same issue. When I tried to change the loud speaker the phone randomly shows blue screen and crashes. Now it won't even boot or enter the recovery mode, only download mode.
When I restore the stock firmware it keeps booting forever on samsung logo.

Could anyone help me please ? :)

Hello guys.. I have some problems about my samsung wave 2.. I think it is bricked but i m not sure.. Here you are some information about my problem:
-when i take charge to phone sometimes it says "file not found" or nothing happend..
- i tried to flash or something but nothing happend again
I read about jtag or something else but i could not understand my problem yet. Could any one help me about this case what is my phones problem how can i fix it? thank you..

mehmetdyn said:
Hello guys.. I have some problems about my samsung wave 2.. I think it is bricked but i m not sure.. Here you are some information about my problem:
-when i take charge to phone sometimes it says "file not found" or nothing happend..
- i tried to flash or something but nothing happend again
I read about jtag or something else but i could not understand my problem yet. Could any one help me about this case what is my phones problem how can i fix it? thank you..
Click to expand...
Click to collapse
Wave is hard to brick.
File not found means Fota try to find an android kernel somewhere. (I guess you had badadroid or stuff like that).
Either put a valid android kernel at the good place (depend of the fota you are using), then install android.
Or boot in download mode and flash a FULL bada firmware (one containing Bootfiles and Fota).

BenzoX said:
Wave is hard to brick.
File not found means Fota try to find an android kernel somewhere. (I guess you had badadroid or stuff like that).
Either put a valid android kernel at the good place (depend of the fota you are using), then install android.
Or boot in download mode and flash a FULL bada firmware (one containing Bootfiles and Fota).
Click to expand...
Click to collapse
But it doesn't work imm how can i say i could not start it. Yeah i had badadroid in phone micro sd. Coud you help me about fixing it ? Just say me what i should do step by step again thank you

Sometimes when i putcharging it says like that

now after some trying to get download mode it just open for a sec i see "download mode" and it turns off again..

mehmetdyn said:
now after some trying to get download mode it just open for a sec i see "download mode" and it turns off again..
Click to expand...
Click to collapse
Maybe battery empty...
Try to charge Battery...
I mean in working handset or in other ways...
Google... how to charge battery without handset or check this thread...
http://forum.xda-developers.com/showthread.php?t=2365748
Best Regards

adfree said:
Maybe battery empty...
Try to charge Battery...
I mean in working handset or in other ways...
Google... how to charge battery without handset or check this thread...
http://forum.xda-developers.com/showthread.php?t=2365748
Best Regards
Click to expand...
Click to collapse
Thanks to all i fix it finally

Help Galaxy Watch

Hello everybody
My watch doesn't work. It was suddenly one day, when I woke up and tried to switch on, and I don't know why.
I tried to flash again with odin in wireless mode and apparently it must work because the program show me it has been with success but when I tried to switch on, the watch shows "Samsung" and after a while, it switch off automatically. I did it in several times and the result always is the same, even the watch doesn't charge.
Can anyone help me to fix it, please?
The watch is a R800 (46 mm) model
Thanks in advance

1.
Are you still able to enter Download Wireless?
In theory you can check here also Battery... in %
And also you could charge in this Mode...
2.
You flashed Firmware...
Filename? Or is this info Top Secret...
So I can see which Version you have tried...
3.
Can you check infos in Odin screen... This is the Download Mode... Example:
https://forum.xda-developers.com/showpost.php?p=73607036&postcount=1
Can you post Photo of your screen... or write ALL Informations as text?
4.
If Battery full and no success with Stock Firmware... still no idea if you maybe used old outdated or wrong files...
You could flash Combination Firmware... to see if device after successfully flash boot proper and start...
So first check would be... if BT address is available...
If you can not find... check Serial Number too... maybe something happens to CSA Security partition/folder...
Best Regards

adfree said:
1.
Are you still able to enter Download Wireless?
Best Regards
Click to expand...
Click to collapse
1. Yes, but when I put it in the wireless charge, the watch doesn´t do anything, the led in the charge starts to flash and doesn't charge
2. Of course it is not, I use one that one coleage put in this thread:
https://forum.xda-developers.com/sm...re-netodin-t3895010/post78800094#post78800094
I t was upload by Huey85 (sorry but I can't attach it becasue I am working and my net cannot allow it).
3. I cannot attach any image because I am working now but I think there is no important thing in the screen. I can flash it without any problem and Odin says all is correct when it finish but after that the watch still doesn´t work (if you need any image of the screen, please tell me and I will upload tomorrow).
4. How can I check the BT address? becasue the phone doesn't recognize.
Thank you for your answer.

4. How can I check the BT address? becasue the phone doesn't recognize.
Click to expand...
Click to collapse
If you can flash Combination Firmware... this is Factory/Service crap and not same like Stock crap...
If device boot proper you can check in settings...
...but I think there is no important thing in the screen.
Click to expand...
Click to collapse
This is the reason why I am asking...
Is RL on or off and Warranty Values are still normal?
Few users were able to type this little bit text on screen...
Anyway. I hope it is now clear what I mean with Combination Firmware...
Best Regards

Combination Firmware for SM-R800 is for instance here:
https://shell.boxwares.com/default.aspx?DeviceModel=SM-R800&Type=All#fh5co-table
Best Regards

Sorry but I don' understand well what you mean with combination firmware. Do you mean that it's not the opcion I have to do? Because I see do you sent the links to other files with the extension md5 but I don't see the opcion in the Odin program to choose these kind of files.
Thnaks again for your interest.

A
My English is bad... but my German is much better.
You can write PM to me in German...
B
I "wish" I could see my request about Odin screen...
As I have NO Crystal Ball...
In this Screen are usefull good infos...
C
Maybe I spend little bit time to search Video or Screenshots about Combination Firmware...
Seems "Mission Impossible"...
Please give full details...
Filenames...
Screenshots...
Photos...
I mean for task B...
What your Watch show if you enter Download/Odin Mode...
Again example from other Watch...
https://forum.xda-developers.com/showpost.php?p=73607036&postcount=1
Best Regards
Edit 1.
Here are 3 Scrrenshots... from other device... please excuse it is not from SM-R800... R810...
https://forum.xda-developers.com/showpost.php?p=74591475&postcount=13
I hope you can see difference between normal Stock Firmware... and Combination Firmware...

A
My English is not good either
B and next
I'm sorry a lot, I'm a newbie in these things. Now I know the difference between the both firmwares
Here you are some pictures, I hope they can help you to find out what is happen
http://ibb.co/nbBh0nF
http://ibb.co/GHnhWd2
http://ibb.co/S3Lv0H6
http://ibb.co/gV3d61s
http://ibb.com/k0bRJLw

A
Attached is "Photo" from ODIN Mode from SM-R810...
Taken from Youtube Video:
https://www.youtube.com/watch?v=oQNOaZ8-BTQ&feature=youtu.be
B
Here is template for text...
Code:
[COLOR="Red"][B]ODIN MODE[/B][/COLOR]
PRODUCT NAME:
CURRENT BINARY:
SYSTEM STATUS:
REACTIVATION LOCK:
WARRANTY VOID:
AP SWREV:
Best Regards

Galaxy Watch R805U no booting to OS

Hi all, I just had a problem yesterday of which my watch not booting to OS. This morning I tried to flash firmwares via NetOdin, all passed but still no working. Only booting to Samsung Galaxy Watch Logo and then black screen. Any suggestions? Thanks

A
Can you post Photo or text from Odin Screen?
https://forum.xda-developers.com/showpost.php?p=73607036&postcount=1
You can leave Download Mode by holding Power Key few Seconds...
B
Is Download Wireless still working?
Or did you tried Recovery option in Reboot Menu?
Best Regards

adfree said:
A
Can you post Photo or text from Odin Screen?
https://forum.xda-developers.com/showpost.php?p=73607036&postcount=1
You can leave Download Mode by holding Power Key few Seconds...
B
Is Download Wireless still working?
Or did you tried Recovery option in Reboot Menu?
Best Regards
Click to expand...
Click to collapse
Download mode and wireless download mode can boot into as normal except recovery. I also can reflash firmware as normal but after completed Watch not boot to OS. Only Samsung Logo. Thanks

Looks good.
SM-R805U :good:
Reactivation Lock OFF :good: :good:
Warranty V. 0 0x0000
Samsung Official :good:
Official :good:
My suggestion.
Flash Combination Firmware.
Check this:
Code:
Serial Number is visible
IMEI is visible
WiFi address visible
BT address visible
Sometimes something to CSA partition could happen...
And hang on Logo remembers me on Security reason...
Gone IMEI is 1 Security Reason...
Best Regards

adfree said:
Looks good.
SM-R805U :good:
Reactivation Lock OFF :good: :good:
Warranty V. 0 0x0000
Samsung Official :good:
Official :good:
My suggestion.
Flash Combination Firmware.
Check this:
Sometimes something to CSA partition could happen...
And hang on Logo remembers me on Security reason...
Gone IMEI is 1 Security Reason...
Best Regards
Click to expand...
Click to collapse
Yes I did. I have flashed combination firmwares of 3 different builds. All flashes was successful but still no luck to boot to OS. Thank you very much for trying to help.

Yes I did. I have flashed combination firmwares of 3 different builds. All flashes was successful but still no luck to boot to OS.
Click to expand...
Click to collapse
Are you sure we mean the same?
A
I have forgotten...
Why you only choose 1 file... if you need to flash 4 files.
From your first post... Odin Screenshot
B
With Combination Firmware I mean this:
Code:
[B]COMBINATION[/B]-FT40_R805USQU1ASL2.tar.md5
This time 1 single file... so only 1 file to choose in netOdin
Summary:
Normal Stock Firmware looks like this:
Code:
BL_R805USQU1CSL2_usr.tar.md5
AP_R805USQU1CSL2_usr.tar.md5
CP_R805USQU1CSL2_CL1315275_QB14780771_SIGNED.tar.md5
CSC_OYN_R805UOYN1CSL2_usr.tar.md5
I can count 4 files...
So you need to flash 4 files.
Best Regards

adfree said:
Are you sure we mean the same?
A
I have forgotten...
Why you only choose 1 file... if you need to flash 4 files.
From your first post... Odin Screenshot
B
With Combination Firmware I mean this:
This time 1 single file... so only 1 file to choose in netOdin
Summary:
Normal Stock Firmware looks like this:
I can count 4 files...
So you need to flash 4 files.
Best Regards
Click to expand...
Click to collapse
I did flash with normal stock firmware consisted of 4 files. On screen shot I just tried one file only. Thanks

I will try to collect few Firmware Links to free available Combination Firmware...
Need some time...
I will update this post...
Best Regards

adfree said:
I will try to collect few Firmware Links to free available Combination Firmware...
Need some time...
I will update this post...
Best Regards
Click to expand...
Click to collapse
Thanks tomorrow I will try to flash again more specifically v4.O. Thank you a lot for your kind help!

https://samsungcombinationfile.com/samsung-sm-r805u
Here is for instance:
Code:
COMBINATION-FT40_R805USQU1ASA1.tar.md5
Only try if out of luck with Flashing 4 files from Stock Firmware.
Best Regards

adfree said:
https://samsungcombinationfile.com/samsung-sm-r805u
Here is for instance:
Only try if out of luck with Flashing 4 files from Stock Firmware.
Best Regards
Click to expand...
Click to collapse
I tried but still no luck of working. Thanks

Okay, this is bad... if Combination Firmware not boot...
Last attempt... flash all 4 files with netOdin:
Code:
BL_R805USQU1CSL2_usr.tar.md5
AP_R805USQU1CSL2_usr.tar.md5
CP_R805USQU1CSL2_CL1315275_QB14780771_SIGNED.tar.md5
CSC_OYN_R805UOYN1CSL2_usr.tar.md5
After this, if again out of luck... please post Photo from Download Mode again...
So we can check Warranty Void info... if still:
Code:
0 0x0000
Something bad happens to your GW...
And you can not fix this at home... :crying:
If Warranty still 0 0x0000 try to send to Repair Service...
Best Regards

adfree said:
Okay, this is bad... if Combination Firmware not boot...
Last attempt... flash all 4 files with netOdin:
Code:
BL_R805USQU1CSL2_usr.tar.md5
AP_R805USQU1CSL2_usr.tar.md5
CP_R805USQU1CSL2_CL1315275_QB14780771_SIGNED.tar.md5
CSC_OYN_R805UOYN1CSL2_usr.tar.md5
After this, if again out of luck... please post Photo from Download Mode again...
So we can check Warranty Void info... if still:
Code:
0 0x0000
Something bad happens to your GW...
And you can not fix this at home... :crying:
If Warranty still 0 0x0000 try to send to Repair Service...
Best Regards
Click to expand...
Click to collapse
I tried but still not working. Yes my Watch is still this code in 0 0x0000 but I bought with no warranty.
Thank you very much for trying to help me out. Sure, I will seek for repair service at my local place.

I planned to bring my Galaxy Watch for repairing tomorrow's morning. But luckily just about 5 minutes ago I have just pressed turn on unintentionally. And it was booting up and working now. Unbelievable it started working fine. Thanks @adfree for trying to help in last few days.

Hello, I am having a similar issue with my Samsung Galaxy watch SM-R805U, I just downloaded the combination file and I will try to load it tomorrow.
But is there a successful method to get this watch functioning again, without having to repair it?

Leakhanak said:
I planned to bring my Galaxy Watch for repairing tomorrow's morning. But luckily just about 5 minutes ago I have just pressed turn on unintentionally. And it was booting up and working now. Unbelievable it started working fine. Thanks @adfree for trying to help in last few days.
Click to expand...
Click to collapse
What was the last thing you did to get it working? Combo firmware.

sektor1952 said:
What was the last thing you did to get it working? Combo firmware.
Click to expand...
Click to collapse
You may try the Combo firmware. My watch since then is working and have updated to the latest firmware. Good luck!

Leakhanak said:
You may try the Combo firmware. My watch since then is working and have updated to the latest firmware. Good luck!
Click to expand...
Click to collapse
I tried the combo firmware and it was the same result, also is the combo firmware supposed to show some extra text during boot?
And you flashed it on the AP line?

sektor1952 said:
I tried the combo firmware and it was the same result, also is the combo firmware supposed to show some extra text during boot?
And you flashed it on the AP line?
Click to expand...
Click to collapse
Yes on the AP line. At last attempt, please try to flash all 4 files of stock firmware with netOdin. Good luck!

Leakhanak said:
Yes on the AP line. At last attempt, please try to flash all 4 files of stock firmware with netOdin. Good luck!
Click to expand...
Click to collapse
I did that too and wound up with the same result.