Related
Hi,
I managed to screw up just about really bad with my Defy+ after flashing it with Waikiui which i afterwards noticed doesnt work with the Defy+ so now im in some hard packed poo here.
I have come to the conclusion that RSD Lite should do the trick if im lucky but i need to find a good SBF to flash the Defy+ with. Originally this phone rolled with a Nordic (GB?) so im looking for either that or something else that could be a good exchange for it.
Would it be possible to flash it with for an example Cyanogenmod or something?
Regards.
//FlashTec80
On the CM webpage, under the Devices - > Motorola Defy it says says there is no official support for defy+ ... on the other hand on the CM forums there are numerous posts by people claiming it runs just fine, seems like some run into a bug where the battery doesnt charge to 100% or something, you might want to stick to a ROM thats officially approved for your device or do a little bit more reading before you take the plunge. I would have posted links to forums and official page but apparently I cant since Im a noob and I need at least 8 previous posts
Tried to run CM 7 in RDS Lite, but it said that files mentioned in the XML file was missing, is that normal?
You can't flash CM7 using RSDlite. RSDlite is used for flashing of .sbf files!
To get your phone back to life, follow this steps:
1. Phone off, battery out
2. Hold Volume Up and Power Button and put the battery back in while holding the buttons - phone will boot into it's bootloader - you will see some white letters saying Bootloader Version 09.10 etc..
3. Install latest USB drivers - found here - http://developer.motorola.com/docstools/USB_Drivers/
4. Start up RSDlite on your PC (you need version 5.3.1)
5. Use this sbf - link (put the .sbf file in root C:/ and rename it to something short (e.g. defy235.sbf)
6. Select that sbf file in RSDlite and press START
7. Wait until the process reaches 100%, by that time your phone will be completely turned on > it's alive again
Can't write more, need to get going to classes, but will help you with everything else, as well. It's easy, just be patient.
P.S. Ignorance killed your defy+, not awesomeness
Cheers!
niksy+ said:
You can't flash CM7 using RSDlite. RSDlite is used for flashing of .sbf files!
To get your phone back to life, follow this steps:
1. Phone off, battery out
2. Hold Volume Up and Power Button and put the battery back in while holding the buttons - phone will boot into it's bootloader - you will see some white letters saying Bootloader Version 09.10 etc..
3. Install latest USB drivers - found here - http://developer.motorola.com/docstools/USB_Drivers/
4. Start up RSDlite on your PC (you need version 5.3.1)
5. Use this sbf - link (put the .sbf file in root C:/ and rename it to something short (e.g. defy235.sbf)
6. Select that sbf file in RSDlite and press START
7. Wait until the process reaches 100%, by that time your phone will be completely turned on > it's alive again
Can't write more, need to get going to classes, but will help you with everything else, as well. It's easy, just be patient.
P.S. Ignorance killed your defy+, not awesomeness
Cheers!
Click to expand...
Click to collapse
You are so true, my most serious side of ignorance put me here and your best side of awesomeness seems to save my ass, i hope
Noticed that the file that im downloading was namned .gz as a file ending, should i just delete that part or do i need to do something with it, decompress or something?
I cant try this before i get home from work but i will try it later, a quickie, would u suggest CM7 or MSginger do be installed over this in the ending? Or would u suggest something else
that u know works good
Hope classes going great and have a safe day
Regards.
FlashTec80 said:
You are so true, my most serious side of ignorance put me here and your best side of awesomeness seems to save my ass, i hope
Noticed that the file that im downloading was namned .gz as a file ending, should i just delete that part or do i need to do something with it, decompress or something?
I cant try this before i get home from work but i will try it later, a quickie, would u suggest CM7 or MSginger do be installed over this in the ending? Or would u suggest something else
that u know works good
Hope classes going great and have a safe day
Regards.
Click to expand...
Click to collapse
Decompress .gz
And yeah i u get stuck at the Motorola Bootanimation pull the battery and goto stock recovery and wipe data that should boot it...
Sent from my MB526 using xda premium
FlashTec80 said:
You are so true, my most serious side of ignorance put me here and your best side of awesomeness seems to save my ass, i hope
Noticed that the file that im downloading was namned .gz as a file ending, should i just delete that part or do i need to do something with it, decompress or something?
I cant try this before i get home from work but i will try it later, a quickie, would u suggest CM7 or MSginger do be installed over this in the ending? Or would u suggest something else
that u know works good
Hope classes going great and have a safe day
Regards.
Click to expand...
Click to collapse
Had a safe day Some bloody hooligans were on the bus home, though... Goddamn idiots. Anyway, on the brighter side of life...
You got your phone working again, mate? I suggest you stick with your stock ROM until tomorrow, then I'll walk you through the ROM's I've used and that'll help you make your pick and I'll help you with installing them, as well.
The fact that it's midnight here and that I get up at 6 for classes tomorrow is the reason you will have to wait for me
niksy+ said:
Had a safe day Some bloody hooligans were on the bus home, though... Goddamn idiots. Anyway, on the brighter side of life...
You got your phone working again, mate? I suggest you stick with your stock ROM until tomorrow, then I'll walk you through the ROM's I've used and that'll help you make your pick and I'll help you with installing them, as well.
The fact that it's midnight here and that I get up at 6 for classes tomorrow is the reason you will have to wait for me
Click to expand...
Click to collapse
Bloody hooligans should just go home and stay there
Yepp its working now but in a rush as i always is, its now running MS2Ginger 3.0, thought i´ll go that route till there is a proper ICS version of something out there
Thanks for all the help, with it i would for sure still be in pure panic mode
Know anything about overclocking the Defy+?
FlashTec80 said:
Know anything about overclocking the Defy+?
Click to expand...
Click to collapse
SetVsel
King_Rat said:
SetVsel
Click to expand...
Click to collapse
Ok i´ll try that, how high is it possible to go to still be stable?
FlashTec80 said:
Ok i´ll try that, how high is it possible to go to still be stable?
Click to expand...
Click to collapse
I'm glad you got to MS2G by yourself
I think the best way is to overclock in Recovery. You'll find the CPU menu when you open it and there you'll see 3 or 4 different settings. Every setting has a clock option and a vsel option. vsel sets the amount of electrical power that the CPU gets at a certain clock.
Best way to overclock would be to go step by step. Increase the highest clock setting by 50MHz, then reboot your phone and see if it works OK If it doesn't boot successfully or it hangs while you're using it - increase the vsel by 1. Then if it's stable, go on, another 50MHz+ and testing again...
Other than that, you can just set it to 1200MHz at once and increase the current vsel for that clock setting by 3-4, that would probably work as well
I have never overclocked mine, though Well, actually, the WIUI ROM come's with overclocked setting itself, it was at 1.1GHz, but it was slower than Pikachu at 1.1GHz So, overclocking doesn't help as much as a good ROM does At least that's my opinion.
P.S. CM9 (ICS) is wonderful But, you should wait for a couple more builds, while the things get even better. For me, CM9 and stock ROMs (including ms2ginger) are the best! You can always test, anyway I've come down to CM7 from CM9 and I'm truly sad
Defy+ stuck at boot amnimation
Hello everyone, my Defy+ stuck at Motorola boot animation. And I have the message below when Volume Up + Boot key :
Bootloader
09.10
Battery OK
OK to Program
Transfer Mode:
USB
My sbf is :
DEFYPLUS_U3_4.5.1-134_DFP-231_BLUR_SIGN_USADEFYEMARAB1B8RTFR004.0R_PDS03C_USAJRDNGIBRRTFR_P020_A024_M002_Service1FF.sbf
With the others it just doesn't work.
Please help me.
Well, why don't you flash that sbf to get it back to life?
FlashTec80 said:
Ok i´ll try that, how high is it possible to go to still be stable?
Click to expand...
Click to collapse
I'm on 300 - 19, 700 - 33, 1200 - 54...
just don't set your tweaks @ boot until you've fully tested them ^^ yet a cache clear would rectify being stuck in b/l
That sbf is the only one to make at least my phone stuck in the boot loop.
The others just don't show me anything, I got a black screen.
Maybe the sbf isn't the good one ?
I have done a backup of my system before I used rsd lite. How can I restore it as it's not a sbf file but a directory with .img ... files ?
Good replies every1, i dont know if im doing anything wrong here.
I first installed SetVsel app and changed the values in there, then when running stabilitytest it said i had the value i had chaged to. Uninstalled the app and tried to change value directly in 2ndinit but now when running stabilitytest it sais i only have 1000Mhz, thou in 2ndinit it clearly sais that vsel4 is set to 1200, any idea?
Cheers and have a safe day every1
Edit: "vsel sets the amount of electrical power that the CPU gets at a certain clock", so how high is it possible to push it before i see smoke coming out of my phone?
FlashTec80 said:
Good replies every1, i dont know if im doing anything wrong here.
I first installed SetVsel app and changed the values in there, then when running stabilitytest it said i had the value i had chaged to. Uninstalled the app and tried to change value directly in 2ndinit but now when running stabilitytest it sais i only have 1000Mhz, thou in 2ndinit it clearly sais that vsel4 is set to 1200, any idea?
Cheers and have a safe day every1
Edit: "vsel sets the amount of electrical power that the CPU gets at a certain clock", so how high is it possible to push it before i see smoke coming out of my phone?
Click to expand...
Click to collapse
You need to enable overclock in 2ndinit or load all modules enabled for it to take effect of your changes..
farsight73 said:
You need to enable overclock in 2ndinit or load all modules enabled for it to take effect of your changes..
Click to expand...
Click to collapse
Good post
Could someone with an non overclocked Defy+ make some runs in Quadrant Benchmark, i only made one run before i started changing things
Would also be fun to see some figures on an ordinary Defy
Just two hours left of work this week, then Top Gear Live is the thing for the evening
I did solve my problem. Thanks to anyone
godbod said:
Hello everyone, my Defy+ stuck at Motorola boot animation. And I have the message below when Volume Up + Boot key :
Bootloader
09.10
Battery OK
OK to Program
Transfer Mode:
USB
My sbf is :
DEFYPLUS_U3_4.5.1-134_DFP-231_BLUR_SIGN_USADEFYEMARAB1B8RTFR004.0R_PDS03C_USAJRDNGIBRRTFR_P020_A024_M002_Service1FF.sbf
With the others it just doesn't work.
Please help me.
Click to expand...
Click to collapse
go to recovery mode and wipe to the factory setting.
this happened because your phone is confused between the old and new firmware..
Hello folks! As the title says I have quite a strange issue with some kernels (Franco,LeanKernel and STOCK!!). I flash the kernels after flashing a rom ,doing it clean(all the wipes) and the phone is working fine for couple hours or a day,after that it just going verry sluggish even in appdrawer or when switching desktop screens. I looked at the CPU frequencies and they change as they shouldn't,I can tell that somethig isn't right with the cpu...I have this issue only with those kernels. I tried stock roms,4.2.x roms,flashed even google images to be sure it's stock,tried them with AOKP 4.2 and 4.1 ,CNA and the list could go on...
Is someone else having the same issue??
Any fix for this? I really want to try franco's kernel!!!
1. Hmmm, are you running a live wallpaper?
2. Do you face the same issue while using Trinity Kernel?
3. Are you sure you do not have any app such as SetCPU which is controlling the speed of CPU?
4. If you set the CPU speed back to normal, does this fix the issue?
5. How much space is mostly left on your sdcard?
I hope the answers of these questions will help to identify your problem much bettER
I don't have the same issue with faux's and trinity kernels . I don't have any program,i don't use a live wallpaper, how I can speed back to normal the cpu?
calinoii said:
I looked at the CPU frequencies and they change as they shouldn't
Click to expand...
Click to collapse
I thought you have checked the CPU speed/frequency using an app like "AnTuTu CPU Master".
calinoii said:
how I can speed back to normal the cpu?
Click to expand...
Click to collapse
Using AnTuTu CPU Master, check the speed set for the CPU when the phone is sluggish and if it something other than the normal 1200 MHz then modify it back to normal. This is what I meant
The frequencies changes verry verry fast,that's when the phone becomes sluggish,i have mini freezes,lots of them
calinoii said:
The frequencies changes verry verry fast,that's when the phone becomes sluggish,i have mini freezes,lots of them
Click to expand...
Click to collapse
I think some background processes are causing this so the CPU is trying to respond to them.
I suggest that you do a full wipe, install a ROM and use Franco's kernel, but do not install any other application on your phone, only default ones installed already with the ROM, maybe Gapps as well just to have a usable phone for some time, then check after a day whether it is again sluggish although there are no applications at all or it is still running fine. At least we would be able to know that maybe one of your application is not compatible well with these kernels and causing this mess.
You may want to avoid wiping so try to force stop the applications running in the background (and cached processes as well) to see if one of them is causing this problem.
Good Luck
I did wipe the data and didn't install any application and I have the same issue :-s
calinoii said:
I did wipe the data and didn't install any application and I have the same issue :-s
Click to expand...
Click to collapse
Do you use any widgets?
Nope
I am not sure I have helpful suggestions anymore except to be sure that you are using the correct Franco kernel whether you are running a 4.1 ROM or 4.2 one.
I hope other members can solve this problem for you. Maybe you will get a bettER help if you discuss this with the Franco kernel users on the Franco kernel thread.
Thanks anyway,i'll post this issue on franco's kernel thread and hope for a fix...and be sure i flashed the correct version of kernel )
Anyone? Please?
calinoii said:
I have some others with the same problem,but thisis the latest,no one could help me this far.I already did what you suggested me...I`m sure I did the clean wipes,just installed gapps and nothing else...when it was getting little hot the freezes were starting too,I think i did all I could,many people in this forums adviced me and still nothing,maybe franco's the only one who can help me with this...
Click to expand...
Click to collapse
Carrying on from here where we were in franco's thread. If you're flashing gapps then clearly you aren't using stock ROM like I told you to try. So, my suggestion to you for troubleshooting remains the same:
osm0sis said:
Well that's really peculiar. I'd try flashing stock again using fastboot. I'd fastboot oem lock, then fastboot oem unlock to wipe, then flash the entire image set as in efrant's thread just to make sure it all gets wiped. But unfortunately, like I said, if stock kernel doesn't work over a fresh fastboot flash of Google's factory image on your device there's still something very wrong, and it's likely wrong with the device itself.
Click to expand...
Click to collapse
osm0sis said:
Use the latest Google Factory Image for your device like I suggested, then you can see if you get the OTA immediately or you can flash it yourself. Do all this before you put any apps on, and don't let it put any apps on and see if you still have the issue with a completely stock setup.
Click to expand...
Click to collapse
Please report back only when you've followed that to the letter.
Tried both,the ones from the images,and the gapps on a stock flashed rom via recovery...I'm trying to resolve this for over 2 weeks now...
L.E : Ok,I will pm you when I manage to have some time for doing this again,thanks for your kindnes
I don't care how many times you think you've done it correctly before, I want you to try it AGAIN. And make sure you've completely wiped by using fastboot oem lock and unlock, then follow efrant's thread to the letter for flashing the entire image set. Factory Images ONLY, no stock-ish kitchen garbage.
I'm happy to help you but you've got to follow my instructions, since this is what I would be doing if I had this issue on my device.
Ok,I will,is there anyguide for locking and unlockingthe bootloader ? or simply "fastboot oem lock" and after "fastboot oem unlock" ?
calinoii said:
Ok,I will,is there anyguide for locking and unlockingthe bootloader ? or simply "fastboot oem lock" and after "fastboot oem unlock" ?
Click to expand...
Click to collapse
Yeah those are the commands. That's it. :good:
I think it's mentioned in efrant's post too, but no special guide necessary. Use the adb and fastboot that he attached too if you're new to fastboot.
I'm used to fastboot,I don't even need the guide to see the commands now,I think I used them like 100 times last 2 weeks )
Fair enough. Please follow the guide anyway though, and be sure to also flash userdata.img and recovery.img to be completely stock. You can fastboot boot cwm.img if you need it to flash your OTA afterwards. We just need you at 100% stock so we can try to figure this thing out. Also maybe hold off on adding your Google account so it doesn't start forcing apps onto your device. It could very well still be a rogue app issue so we need to try and keep your device as empty as possible to see if we can rule out hardware defect. :good:
Should I install any apps?
I did everything you said,now i'm waiting for it to boot up
Q&A for ThunderRom800 - Galaxy Tab S 10.5
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:
Sixaxis controller
Hi All
I have been running trunderROM 800 v2 for a while now and I am very happy with it thanks to shaheer and everyone involved for taking the time to make this amazing rom.
I'm having trouble with the sixaxis controller app.
It will connect to the tablet if I run the app with in the first 30 seconds of rebooting but then it will drop out after period of time sometimes hours sometimes just minutes.
The rest of the time it will just hang on listening for controller.
It seems that a something is cutting the connection when it runs in the background and stops the connection being made once it is running. If I connect it within the first 30 seconds everything works for a time, then the red light turns off on the ps3 controller but the app still says that it's connected.
I was wondering if anyone else was having similar issue with this rom and app?
I'm not sure if this is a rom issue or not but it seems to me that it might be as it does work to a point and then stops.
I would be grateful for any help or ideas on how to fix this.
Many thanks Richie
Fix
steelsabre said:
Guys this one was an easy fix... all you have tto do is force close quick connect.
Bam it works.
Samsung quick connect. Force close and disble then you'll be able to connect your controller.
Click to expand...
Click to collapse
All sorted found a quick fit thanks to steelsabre. I can fly my AR Drone again
But quick connect keeps running after I force close and dropping the ps3 controller. Is there anyway to stop it for good or would I have to uninstall it?
thanks again
SaintRichie said:
All sorted found a quick fit thanks to steelsabre. I can fly my AR Drone again
But quick connect keeps running after I force close and dropping the ps3 controller. Is there anyway to stop it for good or would I have to uninstall it?
thanks again
Click to expand...
Click to collapse
Just uninstall using this: https://play.google.com/store/apps/details?id=com.jumobile.manager.systemapp&hl=en
I got it removed on mine.
I was wondering if there was a way to get rid of the sd card notification that pops up on every boot. I thought i saw a tutorial somewhere in another thread but ive searched and searched and still cant find anything
Soooo... sorry in advance, but I am a total newb when it comes to android. I just got the tab s yesterday and have never had an android before. I'm excited to get into rooting and I really want to get rid of all this bloatware but before I go off and try something way over my head I was wondering if anyone could help me get this ROM installed. I already rooted following this guide.
HTML:
http://forum.xda-developers.com/galaxy-tab-s/development/root-cf-autoroot-t800-t2802916
Now that I've done that, can anyone please help with what I need to do next? I have this guide I found but I don't even know what TWRP or aroma installer is xD
HTML:
http://forum.xda-developers.com/showpost.php?p=54660758&postcount=26
I could really use an idiots guide for this lol. Thank you
l8ishop said:
Soooo... sorry in advance, but I am a total newb when it comes to android. I just got the tab s yesterday and have never had an android before. I'm excited to get into rooting and I really want to get rid of all this bloatware but before I go off and try something way over my head I was wondering if anyone could help me get this ROM installed. I already rooted following this guide.
HTML:
http://forum.xda-developers.com/galaxy-tab-s/development/root-cf-autoroot-t800-t2802916
Now that I've done that, can anyone please help with what I need to do next? I have this guide I found but I don't even know what TWRP or aroma installer is xD
HTML:
http://forum.xda-developers.com/showpost.php?p=54660758&postcount=26
I could really use an idiots guide for this lol. Thank you
Click to expand...
Click to collapse
No worries man I was a noob to android back in july. Twrp is a custom recovery when you press the home+power+vol up at the same time while the tab is booting. Aroma installer is an installer inside the rom in which you can pick the apps,launcher and few few other settings while installing the rom. It makes the debloated process easyer. To install twrp you must be rooted and search in the play store twrp. Once its downloaded open it and hit install. You have to pick the exact model you have. May I ask what model is your tab s and size? Once you pick your model you will have to hit the install and it well make you download the file needed for the recovery. It then should say its installed and you will have to reboot into recovery. Twrp recovery is a touch recovery in which you can can install roms. To install roms (thunderrom/rom in a zip) You will have to backup everything. You have to hit the backup tab and check/tick every box in which md5 check, compression, data boxes are optional depending on how much memory you have. Now you just have to slide the slider and it will backup everything. It may take a while and you should have your battery charged while doing this. After your backup is done, now is the installing of the rom. You have to clear dalvik and cache before installing it. To do so I forget which tab its in but it should be in advanced. After clearing those you now hit the install tab. Now you have to select the rom you downloaded and it should be in the downloads folder. When its selected slide the slider and it will install it and take you to amora installer. Just pick the things you want and then it will install it and take you back to twrp. Now just hit the reboot tab and tap system. Then the tab s will reboot and have a custom rom. There are also some helpful videos on youtube to help you and if i forget something. Hope this helps! My fingers hurt lol.
I have a question: I understand I need to do a complete back up before flashing any Rom, but to do that don't I need to install a custom recovery. So does that mean I won't be able to put the stock **recovery** back if I need to?
barth2 said:
I have a question: I understand I need to do a complete back up before flashing any Rom, but to do that don't I need to install a custom recovery. So does that mean I won't be able to put the stock **recovery** back if I need to?
Click to expand...
Click to collapse
To install that backup you will need the custom recovery. You can get back to stock by flashing the stock recovery img. I dont know exactly how to put back on the stock one but custom recovery is mostly needed to install your backups in case something goes wrong.
DUHAsianSKILLZ said:
No worries man I was a noob to android back in july. Twrp is a custom recovery when you press the home+power+vol up at the same time while the tab is booting. Aroma installer is an installer inside the rom in which you can pick the apps,launcher and few few other settings while installing the rom. It makes the debloated process easyer. To install twrp you must be rooted and search in the play store twrp. Once its downloaded open it and hit install. You have to pick the exact model you have. May I ask what model is your tab s and size? Once you pick your model you will have to hit the install and it well make you download the file needed for the recovery. It then should say its installed and you will have to reboot into recovery. Twrp recovery is a touch recovery in which you can can install roms. To install roms (thunderrom/rom in a zip) You will have to backup everything. You have to hit the backup tab and check/tick every box in which md5 check, compression, data boxes are optional depending on how much memory you have. Now you just have to slide the slider and it will backup everything. It may take a while and you should have your battery charged while doing this. After your backup is done, now is the installing of the rom. You have to clear dalvik and cache before installing it. To do so I forget which tab its in but it should be in advanced. After clearing those you now hit the install tab. Now you have to select the rom you downloaded and it should be in the downloads folder. When its selected slide the slider and it will install it and take you to amora installer. Just pick the things you want and then it will install it and take you back to twrp. Now just hit the reboot tab and tap system. Then the tab s will reboot and have a custom rom. There are also some helpful videos on youtube to help you and if i forget something. Hope this helps! My fingers hurt lol.
Click to expand...
Click to collapse
Ok so at what point do I need the thunderrom? And is it preferred to have that on an SD card vs internal memory?
sd card
Can apps write the sd card with this rom?
LTE
i will wait for LTE version....pls..
hey
Can it be installed on t805?
please
Port this rom to t805 and i will be very grateful
How is quad multitasking and 4 way reboot enabled? Can't seem to get them to work....
Yo_MaMa said:
How is quad multitasking and 4 way reboot enabled? Can't seem to get them to work....
Click to expand...
Click to collapse
Quad should work by default? I think 4 way reboot should also. How did you flash this?
DUHAsianSKILLZ said:
Quad should work by default? I think 4 way reboot should also. How did you flash this?
Click to expand...
Click to collapse
Via twrp. Wiped cache, dalvkit, system then flashed, waited 10 min, rebooted and finished first setup. Reflashed on top about 30 minutes ago just to see if it missed some files on the install, but it's still the same.
e: footer is wrong
it keeps saying that
e: footer is wrong
e: signature verification failed
please help
volume
I love this custom rom but why doesn't the volume on my galaxy tab s work anymore. you can't control it
Google Account Manger crashing on setup
Hey folks!
Flashed this rom (both 2.0 and the beta) and I get the same problem when going through the setup of the tablet. When I get to the screen 'some apps are personalized to the user' or something, I need to enter a name, when I do so I click next and I get the error message 'Unfortunately, Google Account Manager has closed unexpectedly' (my wording might be off, but I assume you guys know what I am talking about).
Would really like to try out this rom, but can't seem to figure out how to fix this issue.
FIXED:
When I put in anything into the name fields, the app crashed. Leaving them blank allows the process to continue.
Hey guys, first i come from VN and my English is not good. Hope everyone can understand.
My device sometimes stop working then auto reboot. The screen auto off and about 3-4 second the led turn red color and the screen turn on then screen blur little with some blur stripe and it auto boot. It's make me scare :"( do you have same problem and what can we do to stop it?
My device still work ok but sometimes this happen.
Thanks.
Try factory reset, otherwise you need to send the device for repair. I do not have any issue with my Z5 the only issue I had was when my MicroSD card stop working (could not write to it could only read) and my device rebooted and slowed down. I replaced my MicroSD card and everything is great since then.
Sent from my SO-03H using Tapatalk
francisamarsingh said:
Try factory reset, otherwise you need to send the device for repair. I do not have any issue with my Z5 the only issue I had was when my MicroSD card stop working (could not write to it could only read) and my device rebooted and slowed down. I replaced my MicroSD card and everything is great since then.
Sent from my SO-03H using Tapatalk
Click to expand...
Click to collapse
Ok maybe i should find another way, i have unlocked BL so i think it is the problem
You not alone same exactly like me your install xpose?
DamBadz said:
You not alone same exactly like me your install xpose?
Click to expand...
Click to collapse
no my device not have xpose, i install xpose but it is not work, iit said that i hhave some problem with framwork and maybe i must flash via recovery to use it. then a del it )
dante224 said:
no my device not have xpose, i install xpose but it is not work, iit said that i hhave some problem with framwork and maybe i must flash via recovery to use it. then a del it )
Click to expand...
Click to collapse
Ok bro don't worry it look scary i know
DamBadz said:
Ok bro don't worry it look scary i know
Click to expand...
Click to collapse
hey, can you reply Auras79 ? i can't reply bcoz i am a new user. if you can, please said him still his rom but just keep stock sound don't increase volume at http://forum.xda-developers.com/z5-premium/development/ub-romaur-v1-0-xpz5p-170-fast-stable-t3259875
Thanks alot bro:good:
dante224 said:
no my device not have xpose, i install xpose but it is not work, iit said that i hhave some problem with framwork and maybe i must flash via recovery to use it. then a del it )
Click to expand...
Click to collapse
I'm 99% sure the reason is that you install custom firmware and xposed module, but mess something up... as a result you get a lot of garbage in System UI and Launcher UI settings.
The common reason of reboots is lag in framework which controlls OVERHEATING...device think that CPU temp is critical and reboots.
So if you are scared about this, my advice is to install clean STOCK firmware,
p.s. but installing of xposed module is fixed already and you can find very detailed guide http://forum.xda-developers.com/crossdevice-dev/sony/workaround-bootloops-xposed-lollipop-t3089203
and the part of it you need is
Quote:
by @mionica
Anybody who is still having any kind of issues, for whatever reason, please do the following:
get into TWRP;
install, in this order, without rebooting:
xposed-uninstall-v1.1.zip
If you don't have an sd card, you'll need to reboot once after the uninstall .zip, boot the system normally, then get back in the recovery and install the other 3. This only applies to people who don't use an SD card
xzdr-busybox-enable-v1.0.zip
xposed-sdk21-arm-date.zip
xposed-leakplug-v1.2.zip
copy the logs to the PC, over USB:
uninstall_xposed.log
install_busybox.log
install_leakplug.log
each of the 3 zip's will tell you where it saved the log (it's usually the external sdcard)
reboot to system
Thanks in advance for not asking any questions about whether you have to do any of these steps; yes, you have to.
Easy
Cheers
vital21 said:
I'm 99% sure the reason is that you install custom firmware and xposed module, but mess something up... as a result you get a lot of garbage in System UI and Launcher UI settings.
The common reason of reboots is lag in framework which controlls OVERHEATING...device think that CPU temp is critical and reboots.
So if you are scared about this, my advice is to install clean STOCK firmware,
p.s. but installing of xposed module is fixed already and you can find very detailed guide http://forum.xda-developers.com/crossdevice-dev/sony/workaround-bootloops-xposed-lollipop-t3089203
and the part of it you need is
Quote:
by @mionica
Anybody who is still having any kind of issues, for whatever reason, please do the following:
get into TWRP;
install, in this order, without rebooting:
xposed-uninstall-v1.1.zip
If you don't have an sd card, you'll need to reboot once after the uninstall .zip, boot the system normally, then get back in the recovery and install the other 3. This only applies to people who don't use an SD card
xzdr-busybox-enable-v1.0.zip
xposed-sdk21-arm-date.zip
xposed-leakplug-v1.2.zip
copy the logs to the PC, over USB:
uninstall_xposed.log
install_busybox.log
install_leakplug.log
each of the 3 zip's will tell you where it saved the log (it's usually the external sdcard)
reboot to system
Thanks in advance for not asking any questions about whether you have to do any of these steps; yes, you have to.
Easy
Cheers
Click to expand...
Click to collapse
Dear Sir, im very happy with your's help, everytime i flash Aroma Rom, everytime i have this problem @@ when i used flashtool to flash stock FW .170 My device clearly and this problem not happened @@
This is my first ever ROM to post up. I just recently started building them. This is a stock deodexed Nougat ROM that is pre rooted. It is 100% AT&T Nougat with just a few fixes. I have left all Samsung and AT&T bloat for those that want all the bloat but like to be rooted and deodexed.
Follow the steps below for installation:
Step 1: You must already be on Nougat firmware. There are various threads on how to do this but if you can not figure it out just ask and i will try to assist you the best i can.
Step 2: Once on Nougat, root your device. Follow this guide https://forum.xda-developers.com/tm...eres-how-rooted-nougat-s7-edge-g935t-t3567502
Step 3: Once Rooted, install Flash fire from playstore.
Step 4: Open Flashfire and grant SuperSU access, once you are at the main menu, press the + and select Flash ZIP or OTA, go to the place you stored the ROM and selecet it. On the next screen MAKE SURE "Mount /system read/write" is selected and click the check mark in the upper right hand corner.
Step 5: Click the + sign again and select "Wipe", leave the defaulted boxes checked (System data, 3rd party apps, and Dalvik cache) and click the check mark in the upper right corner again. ( optional, you can select internal storage but you don't have to).
Step 6: VERY VERY IMPORTANT, select and hold down on Wipe and move it above "Flash ZIP or OTA"
Step 7: Make sure EverRoot is disabled and Reboot is set to normal.
Step 8: Click the lightning bolt and then yes on the next prompt, and let FF do it's thing.
*****Be patient, it will take up to 15 min to boot but most times it is quicker than that.*****
* Fixes i added
Fingerprint fix after root. Thanks to @qwewqa
Replaced IMSService.apk to remove hurricane icon.
CPU Fixes. Thanks to @stang5litre
Issues:
Phone forgetting Bluetooth devices after reboot, I am trying to find a fix for it and will update when i do.
Thanks @stang5litre for countless hours and days of walking me through so many steps from setting up my kitchen to fixing my phone via TV and ADB.
Thanks @SuperR. for the kitchen and all the continued support
Thanks @Chainfire for Flashfire and SuperSU
Download link: https://www.dropbox.com/s/17w8ut192jwixnw/G930AUCS4BQE1.zip?dl=0
Where did you get the ATT stock firmware?
Edit: nevermind I thought you had the latest firmware sorry. Good luck on your first rom
jrkruse said:
Where did you get the ATT stock firmware?
Edit: nevermind I thought you had the latest firmware sorry. Good luck on your first rom
Click to expand...
Click to collapse
Thanks bud. I've been looking for the latest but can't find it. I tried to pull it from my phone using superR kitchen but couldn't deodex it correctly. So inn still working on it. Lol
Congrats bud!!!
Cool. Does adoptable storage work with this ROM?
yuejon said:
Cool. Does adoptable storage work with this ROM?
Click to expand...
Click to collapse
This is 100% stock rooted, deodex, if it didn't work on stock unrooted, chances are that it don't work on this one either.
Hello, I've flashed the rom and loving it so far, it is buttery smooth and seems to have the same battery drain as in stock, but two problems... Every reboot or when I just turn off the wifi, it forgets the password. I've tried build prop editor and set ro.securestorage.suppprt to false, but no success. Another problem, Blutooth won't turn on. It used to before I changed the build prop, but now, it just doesn't turn on. I'm not sure if it is a problem with nougat root or your rom itself, I would love some answers. Otherwise the rom is great and I hope you continue to update it as there isn't a lot of development in AT&T.
OfferedBison said:
Hello, I've flashed the rom and loving it so far, it is buttery smooth and seems to have the same battery drain as in stock, but two problems... Every reboot or when I just turn off the wifi, it forgets the password. I've tried build prop editor and set ro.securestorage.suppprt to false, but no success. Another problem, Blutooth won't turn on. It used to before I changed the build prop, but now, it just doesn't turn on. I'm not sure if it is a problem with nougat root or your rom itself, I would love some answers. Otherwise the rom is great and I hope you continue to update it as there isn't a lot of development in AT&T.
Click to expand...
Click to collapse
Thank you for your feedback. I have experienced the Bluetooth issue on another more custom rom that I'm building, i haven't pin pointed it yet but am still working on it. I was originally thinking it had something to do with something that i removed from the rom (bloat) because when i run this rom with all the bloat i didn't have the issue. I will switch back to this rom and run it for a few days and see if the issue pops back up. As for the WiFi password, i have no problem with that and i have mine set to "true". I'll look into it though and get back with you.
For the battery drain, install kernel auditor, settings menu in top left corner, go to cpu, and set the governor to "on Demand" that will help a little bit.
dirtydodge said:
Thank you for your feedback. I have experienced the Bluetooth issue on another more custom rom that I'm building, i haven't pin pointed it yet but am still working on it. I was originally thinking it had something to do with something that i removed from the rom (bloat) because when i run this rom with all the bloat i didn't have the issue. I will switch back to this rom and run it for a few days and see if the issue pops back up. As for the WiFi password, i have no problem with that and i have mine set to "true". I'll look into it though and get back with you.
For the battery drain, install kernel auditor, settings menu in top left corner, go to cpu, and set the governor to "on Demand" that will help a little bit.
Click to expand...
Click to collapse
Thank you. The Bluetooth problem was fixed when I reverted the changes I made in build prop, and for the wifi problem I think it was something I froze in titanium backup, since I froze some bloat etc.
OfferedBison said:
Thank you. The Bluetooth problem was fixed when I reverted the changes I made in build prop, and for the wifi problem I think it was something I froze in titanium backup, since I froze some bloat etc.
Click to expand...
Click to collapse
The changes you made in build.prob? You mean by setting the secure.storage to false? I do know that on the custom Rom I'm building, i had it set to false and i was having the blue tooth issue, for the WiFi issue, it could be something you froze, can you SS your frozen list.
dirtydodge said:
The changes you made in build.prob? You mean by setting the secure.storage to false? I do know that on the custom Rom I'm building, i had it set to false and i was having the blue tooth issue, for the WiFi issue, it could be something you froze, can you SS your frozen list.
Click to expand...
Click to collapse
Here,
OfferedBison said:
Here,
Click to expand...
Click to collapse
Thanks, the only two things that I'm not sure what it is, is UPSM_N and com.android.Samsung. M. I'm not saying that could be causing it but I'll habe to research what those two things are. Thank you.
dirtydodge said:
Thanks, the only two things that I'm not sure what it is, is UPSM_N and com.android.Samsung. M. I'm not saying that could be causing it but I'll habe to research what those two things are. Thank you.
Click to expand...
Click to collapse
I defrosted android.samsung, but cannot defrost upsm.n, weird. This doesn't seem to be the problem as it still persists.
OfferedBison said:
I defrosted android.samsung, but cannot defrost upsm.n, weird. This doesn't seem to be the problem as it still persists.
Click to expand...
Click to collapse
So your still having the WiFi problem not remembering password after reboot? My ro.secure is set to true and I'm not having the issue.
dirtydodge said:
So your still having the WiFi problem not remembering password after reboot? My ro.secure is set to true and I'm not having the issue.
Click to expand...
Click to collapse
Unfortunately, yes. Maybe something went wrong when I flashed the rom... I'll try reflashing the rom later , when I have time.
OfferedBison said:
Unfortunately, yes. Maybe something went wrong when I flashed the rom... I'll try reflashing the rom later , when I have time.
Click to expand...
Click to collapse
ok. Yea i would try that. I can't duplicate the issue on my end. Leave the ro.secure storage set to true and see if that fixed it. That's what mine is set at and I'm not having any problems with Bluetooth or passwords at this moment.
dirtydodge said:
ok. Yea i would try that. I can't duplicate the issue on my end. Leave the ro.secure storage set to true and see if that fixed it. That's what mine is set at and I'm not having any problems with Bluetooth or passwords at this moment.
Click to expand...
Click to collapse
I have reflashed the rom and also added a dual speaker mod. Everything is working like a charm. Bluetooth and Wifi are all working.
Flashed this and it works fine, but I also experience WiFi 'losing' passwords.
I just flashed it again and no change. In fact, from the time I enter the WiFi password during setup until setup is done, I have to re-enter WiFi password because it 'forgets' (it reports authentication error later after having worked fine initially)
Any other ways to fix this so I don't have to keep re-entering passwords like this?
JJHiemenz said:
Flashed this and it works fine, but I also experience WiFi 'losing' passwords.
I just flashed it again and no change. In fact, from the time I enter the WiFi password during setup until setup is done, I have to re-enter WiFi password because it 'forgets' (it reports authentication error later after having worked fine initially)
Any other ways to fix this so I don't have to keep re-entering passwords like this?
Click to expand...
Click to collapse
Use root explorer, go to system/build.prop and make sure ro.secure.storage is set to "true" as shown in the attachment. I live around Houston TX so we're prepping for the hurricane at the moment so I might be oit for a few days but I'll try to check back on here as soon as I can. Another issue that has been brought up is the phone forgetting Bluetooth device after a reboot. At this moment there is no fix for it that i can find. As soon as I can find a fix for this i will upload a new version.
same g930a-v models-same problem.pls wanted phone emergency backup file (g930a-v same
same g930a-v models-same problem.pls wanted phone emergency backup file (g930a-v same).help me pls all user phone no down mode.
http://forum.gsmhosting.com/vbb/f10...0a-sbl-error-upload-mode-pls-help-me-2301220/
dirtydodge said:
This is my first ever ROM to post up. I just recently started building them. This is a stock deodexed Nougat ROM that is pre rooted. It is 100% AT&T Nougat with just a few fixes. I have left all Samsung and AT&T bloat for those that want all the bloat but like to be rooted and deodexed.
Follow the steps below for installation:
Step 1: You must already be on Nougat firmware. There are various threads on how to do this but if you can not figure it out just ask and i will try to assist you the best i can.
Step 2: Once on Nougat, root your device. Follow this guide https://forum.xda-developers.com/tm...eres-how-rooted-nougat-s7-edge-g935t-t3567502
Step 3: Once Rooted, install Flash fire from playstore.
Step 4: Open Flashfire and grant SuperSU access, once you are at the main menu, press the + and select Flash ZIP or OTA, go to the place you stored the ROM and selecet it. On the next screen MAKE SURE "Mount /system read/write" is selected and click the check mark in the upper right hand corner.
Step 5: Click the + sign again and select "Wipe", leave the defaulted boxes checked (System data, 3rd party apps, and Dalvik cache) and click the check mark in the upper right corner again. ( optional, you can select internal storage but you don't have to).
Step 6: VERY VERY IMPORTANT, select and hold down on Wipe and move it above "Flash ZIP or OTA"
Step 7: Make sure EverRoot is disabled and Reboot is set to normal.
Step 8: Click the lightning bolt and then yes on the next prompt, and let FF do it's thing.
*****Be patient, it will take up to 15 min to boot but most times it is quicker than that.*****
* Fixes i added
Fingerprint fix after root. Thanks to @qwewqa
Replaced IMSService.apk to remove hurricane icon.
CPU Fixes. Thanks to @stang5litre
Issues:
Phone forgetting Bluetooth devices after reboot, I am trying to find a fix for it and will update when i do.
Thanks @stang5litre for countless hours and days of walking me through so many steps from setting up my kitchen to fixing my phone via TV and ADB.
Thanks @SuperR. for the kitchen and all the continued support
Thanks @Chainfire for Flashfire and SuperSU
Download link: https://www.dropbox.com/s/17w8ut192jwixnw/G930AUCS4BQE1.zip?dl=0
Click to expand...
Click to collapse