I've stripped my phone down and removed the lcd digitizer and it was held in by what looks like thin grey double sided foam tape, I have a new unit to fit but it doesn't come with any tape.
Does anyone know where I can get some proper tape to hold the screen in?
Jon
Related
My screen just shattered yesterday after a drunk night out. I went and ordered a replacement glass from ebay since I'm assuming that it's the glass that's only broken. The touchscreen works fine. I can still use it normally. I have a few questions before I begin. I've watched youtube videos on taking the phone apart. I've read a bunch of threads. I just want to be extra careful.
What do you use to keep the new glass onto the lcd screen? I saw some 2mm 3M adhesive tape. I read that it'll make the screen very sensitive. I've seen people reusing the black adhesive tape it came with.
The tools: Hair dryer, small Phillips head screw driver, metrocards, guitar pick, plastic pry tool, razer blades, rubbing alcohol.
Random though, has anyone bought a different colored glass from their original color? Grey glass with white home button and vice versa. Seems dope lol.
Thanks!
I'm trying to replace the outside glass on an HTC EVO 4G and have a couple questions.
I was able to remove the digitizer, however, I broke the old bezel. I ordered another bezel along with a rear cover and mid-section.
The new part where the LCD and the digitizer attach had two adhesive strips on it. I removed the backing from the adhesive strips and lightly attached the old LCD. After I had put it in place I noticed that the new part where the LCD attaches had a shiny piece of mylar/plastic between the new part and the LCD screen and the old one had a dark grey/black piece. I removed the LCD screen from the new part and but the old grey/black piece of mylar/plastic between the LCD screen and the new part.
However, after I did this I questioned what I had done. By putting the pieced of plastic sheeting between the new part and the existing LCD I would only be attaching this piece of plastic to the new part. The back of the LCD itself would not be attached to anything.
What is the purpose of this plastic sheet and am I supposed to attach it to the adhesive tape and is there any functional diffence betwen the silver one and the black one?
Story: Friend cracked phone. Tec school classmate replaced the screen. She got hair and dust under the screen, and I mean enough to have the screen be pressed down to distort color a lot. I took my screen off, cleaned it, and I need the adhesive replaced. The screen holds but I can still peel it off using the speaker gap. I want it stuck on like new again.
What adhesive size do I buy? And preferably from ebay.
This is the adhesive I used last time I changed my screen. 2mm.
Adhesive Sticker Tape for Use in Cell Phone Repair - 2mm Tape - als... http://www.amazon.com/dp/B00BXYWXY8/ref=cm_sw_r_udp_awd_pciJtb1XA0YTY
________________
IT'S OVER 9000!
Thanks!
Removing the back cover and fixing an unresponsive touch screen.
My daughter decided to drop her 80 Cobalt leaving the screen unresponsive but not broken.
After re-flashing the firmware and ruling out a software issue, I decided to open the case and have a look inside. With a bit of playing about I discovered the matt plastic back panel can easily be unclipped from the shiny plastic surround.
First remove the single tiny crosshead screw from under the sdcard flap. Then unclip the panel using strong fingernails or a thin plastic tool. Work from the speaker end and hinge it up at the camera end as there are four tabs there that locate under the curved shiny plastic part.
Inside there are two rectangles of plastic sticky tape in the same place, under one of those is the touch screen ribbon. I removed the plastic tape and found the ribbon was unseated, I just pushed it back into the connector and replaced the plastic tape, which appears to be the only thing holding it in place. The touch screen sprang back into life.
Replace the back cover and small screw. Job done.
It should only take a few minutes to repair.
After the digitizer connector is snapped into place and screwed down, is it wise to test it before applying adhesive or does that little strip that sticks out to the side (for grounding) have to be firmly placed/taped down first? I basically want to be sure the screen works before adhesive and tape are applied. Good or bad idea?
Update: Dry fit went well for testing. Used a precision-cut adhesive and peeled off the protective plastic after testing to seat the new screen replacement. Cracked But Not Forgotten brand. Zero problems.