my evo 4g was working fine, until earlier when the down volume stopped working. it clicks down, and the up volume works. idk what is going on, i am currently re-applying the rom i currently have on. someone helpp..
flash a stock rom. If that doesnt help, then the button itself is broke.
sitlet said:
flash a stock rom. If that doesnt help, then the button itself is broke.
Click to expand...
Click to collapse
it wont allow me into the phone to flash the cw back to what an older version. or whatever its called. it says im in 3.0 gingerbread. i want to be in a earlier version.
why is it you very smart people *cough idiots* always blame the rom? It's a hardware issue. NOT SOFTWARE! wow! "My screen broke, must be an issue with rooting it!" REALLY!? As simple as simple can be, the button broke. however, this doesn't mean you have to get a new phone. you can fix the issue yourself or you can get a new unrooted replacement.
Exactly, it's easier to blame software, over hardware as the error.
Gee, this does sound a lot more like a hardware problem, than a software issue. The problem becomes, where to get the parts, to do the repair, if it's a bad switch.
First bet is, check that the switch hasn't just broken loose from the board and reattach it.
But, I would suggest finding someone, who knows how to work with RoHS solder, as it's far harder to work with, than typical lead solder, &, it's never a shinny joint.
Your also working in a very small part, with limited space. Although they do carry RoHS solder, your 40W, Radioshack Iron, with the chisel tip, is not a solution. In fact, it's likely to cause more damage to the part, before it can't reach the proper temps, needed for the work.
As to locating the part, Cannibalization, though sometimes pricey, is still about the only option, for HTC parts. The HTC Droid Eris's, volume control switches, are the same, as the EVO's volume & power switches.
IM
runcool said:
why is it you very smart people *cough idiots* always blame the rom? It's a hardware issue. NOT SOFTWARE! wow! "My screen broke, must be an issue with rooting it!" REALLY!? As simple as simple can be, the button broke. however, this doesn't mean you have to get a new phone. you can fix the issue yourself or you can get a new unrooted replacement.
Click to expand...
Click to collapse
Because there's always a possibility it's a software issue. And flashing a stock rom only takes a few minutes, and it will easily rule out software being an issue.
Related
Ho guys I recently got this phone and was working fine till today. Its not new but used. The Phone actually was working until I flashed a ROM and since then the left side of the keyboard does not work. I rebooted and went to stock sprint evo rom and still cant even start phonen with email cause the whole left side of screen letters dont work and the home button aint working like it did either. I was trying a 3.5 rom and even restored to multiple roms saved prior to all this but no luck. i think the roms was called Energy Runnymede and FEAR ME. any suggestions how to get this back. Tried multiple keyboards cant even calibrate it aint reading that side. Bummed out any suggestions guys thanks..
Sounds like a hardware problem to me
Sent from my PC36100 using XDA App
so depressed now
If the entire left side of the screen is not working then it's definitely a hardware issue. Good news is that you can fix it yourself for a fairly low price. I've never done it so I don't know much about it, but I've seen plenty of threads about replacing the screen/digitizer. Do some searching around, it shouldn't be too hard to fix.
Supersonic Evo 4G | MIUI | Tapatalk
evo4gnoob said:
Sounds like a hardware problem to me
Click to expand...
Click to collapse
Im going to have to agree with him it sounds like a hardware problem. And as far as fixing it yourself it is fairly easy. My suggestion though is open the phone first because HTC had this brilliant idea to make a phone that used two different flex cables. So with that being said open it and see if your phone has the small one or the big one, you dont want to order the screen and then try and fix it and the cable be the wrong size. (if you choose this path your looking for the Evo LCD and Digitizer Assembly or Evo TSP/LCD Assembly, both the same part just named differently based on where you get it from just CHECK THE FLEX CABLE size and save yourself some trouble) Or the much simplier and cheaper fix take it to s Sprint Repair center and let them look at it. As long as its not physically damaged or liquid damaged you'll be fine and they will look at it and either repair it or replace it as long as you have TEP if not should just be a $35 fee again as long as its not physical or liquid damage.
hey guys,
so my friend got a One X, that's Dead...pretty cheap...and we're trying to revive it.
up till now, the phone only vibrates when pressing the power button, screen doesn't wake up. how to access the bootloader "if it's even accessible"?
any way to know if it's fixable?
Uhh, it doesn't sound too easily fixable. If the screen isn't even turning on, you're off to a bad start. Sounds like some kind of hardware fault, not something you'll be able to flash to fix.
AJerman said:
Uhh, it doesn't sound too easily fixable. If the screen isn't even turning on, you're off to a bad start. Sounds like some kind of hardware fault, not something you'll be able to flash to fix.
Click to expand...
Click to collapse
okay, after tinkering with it, the screen has glitches and lights up then turns on.....what's the sign of this? i can't decide if it's hardware or software yet..
how to enter bootloader? sorry never used one x before.
okay so, i'll attach an photo of the screen. and a video of a similar issue.
video link
please anyone that can help, let me know
That's a hardware fault maybe faulty flex cable
jutley said:
That's a hardware fault maybe faulty flex cable
Click to expand...
Click to collapse
if you look at the phone, it's very clean, i can tell it never had a smudge or any fall...also the screen is clean, no scratches. quite a catch! what could have made the flex cable go bad?!
in the boot animation the screen is quite good!
You say in the boot animation the screen is good, does it ever clear up entirely? You COULD get a display like that from software, but it's more than likely hardware. For example, running Gingerbread ROMs on the Infuse with Froyo bootloaders cause similar rainbow effects due to a change in coding, so you can POSSIBLY have a scrambled display without a hardware failure.
It may have just been a faulty phone and that's why it looks like it's in good shape. It's not necessarily something that someone broke. It could be a bad GPU chip, it could be a flex cable as mentioned, it could be a lot of things. If you (or rather your friend) got it for cheap, and you want to try opening it up to inspect the cables, you can find disassembly threads and videos to tell you how. You could be going on a wild goose chase though.
AJerman said:
You say in the boot animation the screen is good, does it ever clear up entirely? You COULD get a display like that from software, but it's more than likely hardware. For example, running Gingerbread ROMs on the Infuse with Froyo bootloaders cause similar rainbow effects due to a change in coding, so you can POSSIBLY have a scrambled display without a hardware failure.
It may have just been a faulty phone and that's why it looks like it's in good shape. It's not necessarily something that someone broke. It could be a bad GPU chip, it could be a flex cable as mentioned, it could be a lot of things. If you (or rather your friend) got it for cheap, and you want to try opening it up to inspect the cables, you can find disassembly threads and videos to tell you how. You could be going on a wild goose chase though.
Click to expand...
Click to collapse
sometimes it boots up with that white messed up screen, sometimes it boots with the sense 4 lockscreen. lags a lot while trying to unlock the lockscreen, after that all hell breaks loose and screen becomes messed up pretty bad.
thanks for the tips man, i will try opening it up and having a look inside.
it could be a bad factory outlet as a friend suggested...
arabology said:
sometimes it boots up with that white messed up screen, sometimes it boots with the sense 4 lockscreen. lags a lot while trying to unlock the lockscreen, after that all hell breaks loose and screen becomes messed up pretty bad.
thanks for the tips man, i will try opening it up and having a look inside.
it could be a bad factory outlet as a friend suggested...
Click to expand...
Click to collapse
Well, hell, you can try reflashing the software if you can see enough in recovery mode (vol down and power at the same time). I can't see how it would hurt it any more. From the sound of it, you either have VERY messed up software, or more than likely, faulty hardware. Does it seem like the display works any better when it's been off for a while (cold)? If it gets worse the longer it's on, or if it had been on and you just rebooted, it would point more towards a faulty gpu chip to me and the heat causing the problem to come out.
Not sure about how warranties transfer or if they do at all (might depend country to country too), but you could see if it's still under warranty and can be sent in before you open it up.
AJerman said:
Well, hell, you can try reflashing the software if you can see enough in recovery mode (vol down and power at the same time). I can't see how it would hurt it any more. From the sound of it, you either have VERY messed up software, or more than likely, faulty hardware. Does it seem like the display works any better when it's been off for a while (cold)? If it gets worse the longer it's on, or if it had been on and you just rebooted, it would point more towards a faulty gpu chip to me and the heat causing the problem to come out.
Not sure about how warranties transfer or if they do at all (might depend country to country too), but you could see if it's still under warranty and can be sent in before you open it up.
Click to expand...
Click to collapse
alright then
i'll post later if it worked out either ways. thanks for your time bro, unfortunetly i'm out of thanks to thank your last post
actually, the screen gets better when used more to be honest. first we got it, the screen never turned on, then after many tries, it finally came up...first time it was like in the pic, second boot it was sense 4 lockscreen, but messed up later on.
arabology said:
alright then
i'll post later if it worked out either ways. thanks for your time bro, unfortunetly i'm out of thanks to thank your last post
actually, the screen gets better when used more to be honest. first we got it, the screen never turned on, then after many tries, it finally came up...first time it was like in the pic, second boot it was sense 4 lockscreen, but messed up later on.
Click to expand...
Click to collapse
Hmm... weird. Not sure what to say. Well, good luck. I hope it works out!
What honestly it looks like to me is that they tried to flash a american version of a rom on to the phone so you have the improper bootloaders and such. hopefully this works for you.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
If the screen turns on then you didnt kill it. here are the stock ruu's for the HTC One X International. Make sure to choose the one proprietary to your phone and country.
(clickme) for a list of downloads
Good luck and please post your findings.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Click to expand...
Click to collapse
thanks guys!
I know I don't own an one x, but I do have a HTC Rezound, and I cracked the screen in it, and mine did the something while watching YouTube videos, but then it just went back to normal, this happened twice to me. I thought my screen was going out, but if yours is doing it and there's no physical damage, had to be something in the phone, or maybe software is that even possible? Lol.
Just thought I'd share what happened to me..
ICS Rezound.
skater95 said:
I know I don't own an one x, but I do have a HTC Rezound, and I cracked the screen in it, and mine did the something while watching YouTube videos, but then it just went back to normal, this happened twice to me. I thought my screen was going out, but if yours is doing it and there's no physical damage, had to be something in the phone, or maybe software is that even possible? Lol.
Just thought I'd share what happened to me..
ICS Rezound.
Click to expand...
Click to collapse
yes it could be a software issue. so your phone had that issue after changing your digitizer/screen? and then became normally by itself later on...?
thanks for the insight
just an additional reference for you, if ever that you want to re-flash a new rom, but can't access SD card, just follow the link, MIGHT help you out... good luck..
http://forum.xda-developers.com/showthread.php?t=1692681
hello
i have the same issue but here in syria we didn't have Agency htc to repair my phone screen sooooo pleassssssssssse if any one live in lebanon can you please tell me were i can go to repair my phone if u knows an a good htc shop or Agency of the HTC (((( for more information i have no scratch on my phone or water inside it )))))) tnxxxxx alot
It's a hardware issue for sure. Doubt it's the cable connection but in need of a bga rework to try and fix it
Sent from my HTC One X using xda premium
mikey0105 said:
just an additional reference for you, if ever that you want to re-flash a new rom, but can't access SD card, just follow the link, MIGHT help you out... good luck..
http://forum.xda-developers.com/showthread.php?t=1692681
Click to expand...
Click to collapse
thanks a lot i'll definitely be need to knowing this, even if not needed now...till i get my own One X
mohanned said:
i have the same issue but here in syria we didn't have Agency htc to repair my phone screen sooooo pleassssssssssse if any one live in lebanon can you please tell me were i can go to repair my phone if u knows an a good htc shop or Agency of the HTC (((( for more information i have no scratch on my phone or water inside it )))))) tnxxxxx alot
Click to expand...
Click to collapse
yes, check your PM.
I've searched the forums for a while and haven't found an issue exactly like this..
At first my phone would boot and the soft keys would light up and the LED would shine while charging. Shortly after that, I had no display and no illumination whatsoever on my screen. I just disassembled the phone to make sure all of the bands and connecters are connected and they are fine. I have reason to believe the screen works because when I receive a call, i can press where I usually would to accept calls and it works.
I have done some research on getting a new digitizer, screen, ribbons, etc.. but it's just too costly to justify it seems.
Any advice would be greatly appreciated
warheed said:
I've searched the forums for a while and haven't found an issue exactly like this..
At first my phone would boot and the soft keys would light up and the LED would shine while charging. Shortly after that, I had no display and no illumination whatsoever on my screen. I just disassembled the phone to make sure all of the bands and connecters are connected and they are fine. I have reason to believe the screen works because when I receive a call, i can press where I usually would to accept calls and it works.
I have done some research on getting a new digitizer, screen, ribbons, etc.. but it's just too costly to justify it seems.
Any advice would be greatly appreciated
Click to expand...
Click to collapse
Try to Odin stock
Sent from my SPH-D700 using Tapatalk 2
You may have to go into sprint and ask for a new screen. That happened to me once and they replaced it and it worked fine ever since. I had water damage on mine though
Sent from my Samsung Epic 4G using Tapatalk 2
xboxfanj said:
You may have to go into sprint and ask for a new screen. That happened to me once and they replaced it and it worked fine ever since. I had water damage on mine though
Click to expand...
Click to collapse
You can do that? Will they deny you if you're using a rooted phone or do you have to go back to stock first...
Sunchips said:
You can do that? Will they deny you if you're using a rooted phone or do you have to go back to stock first...
Click to expand...
Click to collapse
Depends on where you go and who you get. The last time I went, the associate thought it was awesome that I have sense on my phone. If possible, Odin back though.
I did get around to blindly putting my phone into download mode and flashing the stock tar through odin.. I'm assuming the flash worked since I heard the stock boot/shutdown animation theme music accordingly.
Unfortunately the screen and the soft keys are still not illuminated. The QWERTY remains functional including backlighting.
My phone is no longer on any network, but do you think I could still take it up to a location and bs my way into getting at least a used equal or lesser value device?
Put it up on Fleabay as a clean ESN, broken screen phone and stop wasting our time while you try to scam Sprint.
Sent from my SPH-D700 using Tapatalk 2
You're right, certainly not an ethical option. I'm more of a DIY person though, as I'm sure I could say the same for everyone else here.
Do you think it's the whole screen that needs to replaced? Ribbons and all? If so, do you know of a good source for me to purchase what I need
warheed said:
You're right, certainly not an ethical option. I'm more of a DIY person though, as I'm sure I could say the same for everyone else here.
Do you think it's the whole screen that needs to replaced? Ribbons and all? If so, do you know of a good source for me to purchase what I need
Click to expand...
Click to collapse
Don't do it. I bought my Epic for $80 and replacement screen costs $70. AND I'm in China where electronic products and accessories should be cheap.
Sent from Nokia N900 w/ Android 2.3.7
I have a GS3 that was rooted with a CM rom. I was using it the other day and the screen just suddenly went black. I tried rebooting it and popping out the battery, but to no avail. I can't boot it into download or recovery mode either.
When I put in the battery, the phone vibrates but nothing else. When I plug in the USB cable with no battery, it vibrates and the LED comes on for a few seconds before flickering off.
My first priority is data recovery, I've been a bad boy and haven't backed up my data for a while. My second priority is making it so they can't tell I have a flashed ROM when I send it out for warranty service, though AFAIK, this may be a nonissue.
I tried to make a 300k jig, and it didn't work (assuming I got the pins right).
Have you tried KAsp3rd's debrick method?
Stickies in development.
Sent from my SGH-T999 using Tapatalk
DocHoliday77 said:
Have you tried KAsp3rd's debrick method?
Stickies in development.
Sent from my SGH-T999 using Tapatalk
Click to expand...
Click to collapse
I'm not stuck in QHSUSB-DLOAD as far as I can tell. Would it still be effective?
Could be. It basically allows you to boot download mode from the sdcard. From there you Odin flash the firmware and hopefully that would fix it. But if it's a hardware failure, which it could be per your description, I doubt anything will work.
Sent from my SGH-T999 using Tapatalk
New update. I figured out that the 300k ohm resistor trick DOES work, but only for like three seconds. Meaning that they'll be able to see the custom binary count, but (as far as I know) I can't reset it to 0.
The weird part is that it only works if I plug the usb jig into the phone before putting the battery in, if I put the battery in first, it doesn't work. It almost seems like it constantly thinks the power button is being pressed or something.
I guess I'm opening it up and looking for a short. The power button operates normally tactile-y speaking.
EDIT: new new update. I wasn't able to find anything physical when I looked at the pcb. But I verified my theory, somewhat. When I hold home and volume up/down (without touching the power button) when I put the battery in, it boots into download mode for a second before shutting down.
It's not behaving exactly like it would if it was only that though, because I tried holding the power button down on the t999l I got as a replacement, while inserting the battery, and the boot screen shows up for a few, where a boot screen never shows up on the bad phone.
DOUBLE EDIT: can I swap that pcb with the one from the t999l, or are they too dissimilar? Would I be able to swap it with one from another t999, or does the board that has the power switch also have the onboard storage?
TRIPLE EDIT: I answered my own question, the eMMC and the power switch are on the same board. But if the fault is caused by something else (e.g. a camera), would I be able to plug all the other hardware from the t999l into the t999, or can I just boot up the t999 without most of the hardware connected as a test?
I would not risk going through all that trouble. Not quite sure why you would honestly. You got a T999L right? Warranty replacement I assume? It's a superior device so why my not just use it as is?
Sent from my SGH-T999 using Tapatalk
DocHoliday77 said:
I would not risk going through all that trouble. Not quite sure why you would honestly. You got a T999L right? Warranty replacement I assume? It's a superior device so why my not just use it as is?
Sent from my SGH-T999 using Tapatalk
Click to expand...
Click to collapse
1. I really want my data back.
2. I risk getting charged for out of warranty if they see it was rooted and flashed.
3. I'm going to sell it anyways, I got a note 3 because the S3 was on backorder and I couldn't do my job without a smartphone.
1. I'm sorry to say, but plan on this not being possible.
2. If it won't boot there is little chance you'd have to worry about it. They aren't going to go to extraordinary measures to check k the counter. Many people have claimed they sent a dead device back and never got charged, even though the counter had been tripped.
If you damage the good hardware you won't have much to sell.
I don't understand why you'd be willing to attempt to Frankenstein the two devices, but not at least attempt the debrick method I mentioned.
Also, you should be aware, even if it's something else, not a bad chip, it probably won't work. Much of the hardware is in fact different between the two. Different camera, different radios, different SoC....
I wish you luck if you decide to try this, but imo you are taking an awful big risk to try something that probably won't work anyway.
If your data is really that important maybe you should look into a data recovery service.
And in the future, back up back up back up!
Good luck whatever you decide. Let us know what happens.
Sent from my SGH-T999 using Tapatalk
DocHoliday77 said:
1. I'm sorry to say, but plan on this not being possible.
2. If it won't boot there is little chance you'd have to worry about it. They aren't going to go to extraordinary measures to check k the counter. Many people have claimed they sent a dead device back and never got charged, even though the counter had been tripped.
If you damage the good hardware you won't have much to sell.
I don't understand why you'd be willing to attempt to Frankenstein the two devices, but not at least attempt the debrick method I mentioned.
Also, you should be aware, even if it's something else, not a bad chip, it probably won't work. Much of the hardware is in fact different between the two. Different camera, different radios, different SoC....
I wish you luck if you decide to try this, but imo you are taking an awful big risk to try something that probably won't work anyway.
If your data is really that important maybe you should look into a data recovery service.
And in the future, back up back up back up!
Good luck whatever you decide. Let us know what happens.
Sent from my SGH-T999 using Tapatalk
Click to expand...
Click to collapse
Reading through the whole thread, I am going to agree with the Doc. Why would you go to all that trouble ? Nobody is going to be able to salvage that data, let alone snoop in it. You are best move on rather than Creating that Frankenstein Monster as Doc aptly put it.
The frankenphone would only have been for if the phone didn't work without the camera/speaker/etc connected. However when I disconnect everything from the main board except for the screen, I get the same behavior. So I guess the only thing I would want to test would be the touchscreen. I can't find any info on if the t999l touchscreen is compatible with the t999 board, but if anyone knows, that would be great.
I'm still going to try the microsd card debrick method, I was concentrating on the usb jig last night since that got me further than anything else so far.
As to why, I have pictures and whatnot on the phone that I want to save, as well as a bunch of work crap that will take me dozens of hours to recreate, plus a bunch of other personal stuff. If I can't get it, then I can't get it, but I want to exhaust my resources (within reason) before giving up.
dubloe7 said:
I'm still going to try the microsd card debrick method, I was concentrating on the usb jig last night since that got me further than anything else so far.
As to why, I have pictures and whatnot on the phone that I want to save, as well as a bunch of work crap that will take me dozens of hours to recreate, plus a bunch of other personal stuff. If I can't get it, then I can't get it, but I want to exhaust my resources (within reason) before giving up.
Click to expand...
Click to collapse
Try JTAG instead of this if sdcard doesn't work. Most of t999l hardware is supposed to be identical. Since partition are potentially different. So phone may not boot. But you might be able to do adb. Good luck.
Actually it's the other way around. Partition layout is the same (though firmware incompatible) and hardware is definitely different.
Sent from my SGH-T999 using Tapatalk
SD card didn't work, looking for jtag instructions.
EDIT: The more I look, the more it looks like a faulty power switch. Unfortunately, it doesn't look like I have a way to short the power switch or something in a way that doesn't void the warranty...
Any help on this is appreciated.
Well, I think I'm completely screwed now.
I found this, http://androidforums.com/samsung-ga...-help-black-screen-vibrating.html#post5262715 and somehow managed to lift the freaking solder pads.
What do you think the chances that they won't charge me a couple hundred dollars for "out of warranty service" are?
EDIT: good news: Confirmed that the cable that I lifted the solder pads on, which I assume is an antenna, probably isn't the problem (unplugged it on the t999l, and it works fine).
bad news: I also confirmed the power switch itself isn't the problem either. The left and right hand side aren't connected (according to my multimeter) when the button isn't pressed, but they are when it is.
Another edit: I unconfirmed the power switch part. It looks like the button only needs the slightest contact in order to short. I removed the power button from the case, surprisingly difficult since I saw people complaining about it falling out. Now the difficult part is making it think the switch is closed for long enough to not turn it on, but not long enough to turn it back off. I've gotten it to the boot logo, but I haven't gotten it to fully boot.
Yet another EDIT: the only way I can get it to turn on long enough to see the boot logo is by smacking it in my hand after it turns on, which seems to interrupt the constant button press signal. From the metering on the switch, it seems that even less contact is needed to turn on the phone than to signal the multimeter. Any suggestions as to somewhere to cut the power switch signal other than the power switch?
I am in need of help! My phone is dead. Here's the rundown
AT&T Samsung Galaxy Note II (i317)
Used on the Straight Talk Network
Running the latest Unofficial CM12, Lollipop 5.01 for the last week and loved every bit of it. No problems.
I cracked my screen in July and never got it fixed. The cracks spread and I was planning on getting it fixed, but haven't yet. I dropped it two days ago and then the screen wouldn't come back on. The buttons lit up and it would even ring when called. So I thought my screen was finally gone and started looking for a replacement. I took the battery out because I didn't want it ringing without the ability to answer it. Yesterday I put the fully charged battery in and attempted to turn the phone back on. It will not come back on and I think it's more than just the screen now.
Red LED blinks. Half of the screen seems like it is turning on, but then it all goes dark again. Will not enter Download or Recovery. I've been reading and thinking this is more of a hardware issue than software. I've flashed dozens of Roms with only minor issues here and there. I haven't had any issue with Lollipop and can't see it being related, although I could really be wrong.
My question is, is my phone dead? Do I need a new motherboard, along with the screen I was already gonna replace? If that's the case, I will just replace the phone and start over, unless anyone has free parts they want to donate, LOL! Seriously, just looking for input and suggestions.
Thanks
dirtyalphaman said:
I am in need of help! My phone is dead. Here's the rundown
AT&T Samsung Galaxy Note II (i317)
Used on the Straight Talk Network
Running the latest Unofficial CM12, Lollipop 5.01 for the last week and loved every bit of it. No problems.
I cracked my screen in July and never got it fixed. The cracks spread and I was planning on getting it fixed, but haven't yet. I dropped it two days ago and then the screen wouldn't come back on. The buttons lit up and it would even ring when called. So I thought my screen was finally gone and started looking for a replacement. I took the battery out because I didn't want it ringing without the ability to answer it. Yesterday I put the fully charged battery in and attempted to turn the phone back on. It will not come back on and I think it's more than just the screen now.
Red LED blinks. Half of the screen seems like it is turning on, but then it all goes dark again. Will not enter Download or Recovery. I've been reading and thinking this is more of a hardware issue than software. I've flashed dozens of Roms with only minor issues here and there. I haven't had any issue with Lollipop and can't see it being related, although I could really be wrong.
My question is, is my phone dead? Do I need a new motherboard, along with the screen I was already gonna replace? If that's the case, I will just replace the phone and start over, unless anyone has free parts they want to donate, LOL! Seriously, just looking for input and suggestions.
Thanks
Click to expand...
Click to collapse
I see a bunch of views................but not replies. Please Help............Bump!
dirtyalphaman said:
I see a bunch of views................but not replies. Please Help............Bump!
Click to expand...
Click to collapse
There's pretty much nothing to say, but I guess I will.
You can't get to download mode, can't get to recovery mode, you can't see the screen......
If you're looking for a second opinion to say you're f*cked, then consider this it.
If you could get to download mode or recovery mode, it has a chance. But you still have hardware issues like the screen to replace. Which is not fun.
Possible yes. But unless you really know what you're doing and careful as hell, you take the chance of hosing something else up. Like ripping a ribbon cable or yanking a soldered wire out....
I tried replacing a Motorola Atrix screen. The result of that was me buying an Atrix 2.
Unless you are emotionally attached to this phone, bury it.
If not,
https://www.ifixit.com/Device/Samsung_Galaxy_Note_II#guideList
http://www.sw-box.com/Samsung-Galaxy-Note-2-Replacement-Parts.html?p=1
I did some quick searches and doesn't appear to be any kind souls out there with spare parts. You may want to try CraigList or something like that.
Good luck to you
dicksteele said:
There's pretty much nothing to say, but I guess I will.
You can't get to download mode, can't get to recovery mode, you can't see the screen......
If you're looking for a second opinion to say you're f*cked, then consider this it.
If you could get to download mode or recovery mode, it has a chance. But you still have hardware issues like the screen to replace. Which is not fun.
Possible yes. But unless you really know what you're doing and careful as hell, you take the chance of hosing something else up. Like ripping a ribbon cable or yanking a soldered wire out....
I tried replacing a Motorola Atrix screen. The result of that was me buying an Atrix 2.
Unless you are emotionally attached to this phone, bury it.
If not,
https://www.ifixit.com/Device/Samsung_Galaxy_Note_II#guideList
http://www.sw-box.com/Samsung-Galaxy-Note-2-Replacement-Parts.html?p=1
I did some quick searches and doesn't appear to be any kind souls out there with spare parts. You may want to try CraigList or something like that.
Good luck to you
Click to expand...
Click to collapse
Hey, Thanks man! That's what I needed to hear. I have been flashing Roms since I had a Sprint PPC 6700 and I have enough experience to now I was f#@$ed, but I really needed to hear it from someone else. Someone with developer experience. A screen assembly and motherboard cost more than another phone on ebay or Swappa. Welp, back to the drawing board. Anyone got a note 2 they wanna sell cheap?
dirtyalphaman said:
Hey, Thanks man! That's what I needed to hear. I have been flashing Roms since I had a Sprint PPC 6700 and I have enough experience to now I was f#@$ed, but I really needed to hear it from someone else. Someone with developer experience. A screen assembly and motherboard cost more than another phone on ebay or Swappa. Welp, back to the drawing board. Anyone got a note 2 they wanna sell cheap?
Click to expand...
Click to collapse
No worries.
Feb 3 I'll be on 2 years with my Note 2. Longest I've kept one. Only have one smallish crack on the lower left corner.
With everything I've done to it I'm amazed it's still working.