Develop Bugs

Will my tablet recognise my Sony Handycam? Can i upload videos to youtube from it?

Hey guys
So basically I have a Sony Handycam DCR-HC19E camcorder, and was wondering if i plugged it into my galaxy tab using the samsung usb adapter thing, will it recognise it and allow me to take and transfer files to and from the tab?
As i want to upload some videos to youtube but it wont work on my computer?
So im basically asking if anybody has got mass storage access to devices they have plugged into the tab 10.1
Thanks in advance for any help
Adam

I have a Sony dcr-sr100. It mounts to my galaxy tab 10.1 on stock firmware.
I have found that " high" powered USB devices are rejected by this tab, which is annoying. But i have found that how you connect the devices matter also.
E.g. if the adaptor is plugged in then i use my USB drive to the adapter is does not work.
If my USB drive is plugged into the adapter then into the tab it usually works, if not pull out and try again right away.
If you can get a powered USB hub, this will help for connecting more devices. Generic keyboard & mice work fine ( if not " high" powered)
USB mass storage otg app in the market will help to mount more drives at once and enable access to NTFS formatted drives which are not supported on the stock firmware.
Sent from my GT-P7510 using XDA

brb8two said:
I have a Sony dcr-sr100. It mounts to my galaxy tab 10.1 on stock firmware.
I have found that " high" powered USB devices are rejected by this tab, which is annoying. But i have found that how you connect the devices matter also.
E.g. if the adaptor is plugged in then i use my urban drive to the adapter is does not work.
If my USB drive is plugged into the adapter then into the tab it usually works, if not pull out and try again right away.
If you can get a powered USB hub, this will help for connecting more devices. Genetic keyboard & mice work fine ( if not " high" powered)
USB mass storage app in the market will help to mount more drives at once and enable access to NTFS formatted drives which are not supported on the stock firmware.
Sent from my GT-P7510 using XDA
Click to expand...
Click to collapse
Thanks for all this info!
So would u recommend getting a Samsung USB adapter thingy and them trying from their?
Sent from my GT-I9100 using xda premium

This is the one I got.
http://dx.com/p/106541?r=78454077
I don't see much point paying more than this.
Also the " card reader" versions are designed to only mount one card at a time since that is how the stock device handles otg. But if you already have USB card reader your happy with, it can be used with USB mass storage OTG app from the market. ( Which also adds NTFS support).
Sent from my GT-P7510 using XDA

Sprite cheers. I may just get a 3 pound one off Amazon, then see if it works
Sent from my GT-I9100 using xda premium

I got the corded version, as I thought it was more risky using the "Block" style one that might break the connector 30pin if it was knocked too hard.
There is rick of the corded version breaking on the cable, but it is a cheap replacement fix.
Sent from my GT-P7510 using XDA

i need to connect the high powered external 1 TB hard drive

yogeshmha said:
i need to connect the high powered external 1 TB hard drive
Click to expand...
Click to collapse
Ok, what information do you need?
You have made a statement but not asked a question. Answers to your statement have been covered above also.
Sent from my GT-P7510 using XDA

Can some who knows alot about USB otg start a thread

There is a lot of interest about this spread out through all of the threads. Can someone with more knowledge than me on the subject post a "how to" on it? Just an idea to centralize the subject. Thanks
Sent from my Kindle Fire using Tapatalk 2 Beta-5

I meant USB otg. Stupid auto correct
Sent from my Kindle Fire using Tapatalk 2 Beta-5

USB OTG didn't originate on the KF. Do a search on XDA and I'm sure you'll find plenty of threads.

search in threads

Org is present in kernel 3.0 and u can instal ics with kernel 3.0
Sent From my Kindle Fire
Setupetails are Below
Cm7 Barebones+Raven's Kernel
Minimum:300 Higher 1200mhz
Go launcher Ex With MIUI Theme
Games:MC3,Fifa 2012,Real Racing 2,Stick Cricket,Gangster Rio....
Apps:Mx Video Player,JetVid,Titanium Backup,Opera Mobile,Dolphin HD,Adobe Reader

That's the thing, the threads are flooded with otg questions. I my self am not too interested in it, but alot of people are and if there was a guide written for it, it could unclutter the threads a bit. Just trying to bring the topic to one spot.
Sent from my Kindle Fire using Tapatalk 2 Beta-5

Search the threads, derp.
Searching the threads won't help. This information is scattered all over the place making search pretty much impossible. The ridiculously-obselete forum format doesn't help, either.
I did get mounting to work with the Stickmount app from the market. The multiple partitions on my external drive supposedly mount under /sdcard/usbstorage but they show as empty in any file managers.
Edit: Based on Stickmount's info the reason the drives show up empty is more than likely because I'm using an adapter instead of a cable. I'll update when my cable comes in the mail.

all I know is I can't wait for Bluetooth otg, my emulators with a bluetooth wiimote will make me a happy man lol
Sent from my Amazon Kindle Fire using xda premium

smirkis said:
all I know is I can't wait for Bluetooth otg, my emulators with a bluetooth wiimote will make me a happy man lol
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
My ps3 control works awesome with my phone. I would love to use it on this beast
Sent from my Kindle Fire using Tapatalk 2 Beta-5

pbailey212 said:
My ps3 control works awesome with my phone. I would love to use it on this beast
Sent from my Kindle Fire using Tapatalk 2 Beta-5
Click to expand...
Click to collapse
+1 FPSE + ps3 controller = ultimate time killer lol
plus with all this otg stuff would we be able to plug in cams? for possible skype use? or google talk video chat. even better!

otg
hi all iv'e posted a bit about my knowledge of otg in different threads and thought id post what i know/figured out so far in this thread.
please correct me if you know any different.
the only difference between a usb cable & a otg cable/adapter is that the otg has pin 5 joined to pin 4 (this lets your kindle activate otg host mode). unfortunately most cables only have 4 cables attached (even if pin 5 is present in the connector) .
you can find an app called electrodroid in the market to see usb pin-out.
usb controller seems to be a good app to see which devices connect ok.
stick mount works well for me to mount usb drive.
tip's
download stickmount app, open and allow permission
turn off kindle & plug in otg cable connected to a powered hub (mine has a switch on the side, "bus or self", i set it on self) insert flash drive into hub.
then power on kindle when loaded the app stickmount should auto connect your flashdrive (there should be a popup) if not open up stickmount app and hit connect.
then you should see the popup.
open root explorer and goto sdcard you should see usb storage in there (for some reason on my 1st attempt to open root explorer it always shows as empty, just exit the reopen R/E).
?if you unplug otg cable without going into stickmount and disconnecting sometimes you can't remount without a reboot?
a mouse and keyboard should just work but iv'e also found that they also need to be inserted before booting up. my mac keyboard doesn't work at all but my mouse/keyboard combo ie. one dongle which both keyboard and mouse came with works fine
still playing with bluetooth. i can see it in usb controller app but can't switch it on yet, i think this is something hash is aware of and it needs something tweeking in the kernel.
everything seems to need the extra power of a powered hub. i did have my mouse working on its own once or twice but most of the time it needs powered hub.
here's a pic of my setup. hope this helps someone get it working as it's awesome.
http://db.tt/dLg71BRz
Sent from my Amazon Kindle Fire using xda premium

here's version 2
works good a very slight rock to one side operates the power button
http://db.tt/9KQupTRC
&
http://db.tt/ZweZ4f3s
Sent from my Galaxy Nexus using xda premium

lovejoy777 said:
here's version 2
works good a very slight rock to one side operates the power button
http://db.tt/9KQupTRC
&
http://db.tt/ZweZ4f3s
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
You my friend are a genius! That is the coolest freaking adapter ever. Well done sir! I'm gonna give it a go and see if I can do the same
Sent from my Amazon Kindle Fire using XDA

I purchased USB otg cable -- ebay item #280820891599.
Installed stickmount and usb controller apps. Hash's Kernel #8. My generic 2gb USB stick is hot-pluggable, mounts at /sdcard/usbStorage/sda.
USB Controller indicates that my generic BT USB plugs (i have two of them) are "Connected USB devices" with the address 0001:0a12. So the system recognizes them, but what to do next?

i think i'm right in saying that hash needs to tweak the bt modules to allow us to activate it, mine shows the same but there is no way to toggle bluetooth yet.

ttakacs said:
I purchased USB otg cable -- ebay item #280820891599.
Installed stickmount and usb controller apps. Hash's Kernel #8. My generic 2gb USB stick is hot-pluggable, mounts at /sdcard/usbStorage/sda.
USB Controller indicates that my generic BT USB plugs (i have two of them) are "Connected USB devices" with the address 0001:0a12. So the system recognizes them, but what to do next?
Click to expand...
Click to collapse
So, I just need this cable:
http://www.ebay.com/itm/Premium-New...Accessories&hash=item41623abfcf#ht_2784wt_952
and a few apps to be able to mount USB?

Offtopic, but in regards to the bluetooth PS3 controller. I was searching but I couldn't find any guides on how to get the pair code for the device. Do you have to do it within Linux or can it be done within Windows?
On topic, I've purchased a bluetooth controller and I can't wait to play my emulators.

maw230 said:
So, I just need this cable:
http://www.ebay.com/itm/Premium-New...Accessories&hash=item41623abfcf#ht_2784wt_952
and a few apps to be able to mount USB?
Click to expand...
Click to collapse
Yes. That cable and stickmount worked perfectly for me.

ttakacs said:
Yes. That cable and stickmount worked perfectly for me.
Click to expand...
Click to collapse
were u able to mount that 2gb stick without a powered hub? I can mount anything I want with the powered hub but nothing without it.
Sent from my GT-P1000 using xda premium

USB OTG
Hy,
Same here, unable to mount usb stick using USB OTG Cable without having external hub.
The USB OTG cable is working fine on my Galaxy Note.
I've tried several ROM on the kindle fire with kernel #8 but none of them make USB OTG work.
Anyone here can give a clue please ?
Thanks a lot

OTG cable question

This seemed like an accessories question, so i decided to put it here. Has anyone with an OTG cable tried to use a 360 controller with an emulator? That would be awesome. If someone could try, or if someone HAS tried and know if it works or not could let me know that would be awesome.

I doubt VERY highly that it will work, but I have all the stuff to try it so I will report back in around 10 minutes haha.

aaron1006 said:
I doubt VERY highly that it will work, but I have all the stuff to try it so I will report back in around 10 minutes haha.
Click to expand...
Click to collapse
Well in theory it should work because anything thats HID Usb should be supported by otg. Here hopin! haha

For some reason I can't even get my mouse/keyboard to work right now (it has worked before) and unfortunately I'm down to about 5% battery. I'll do further investigation tomorrow.

While you're right that theoretically any USB device can work, you still need the right drivers. The problem is that Android uses a monolithic kernel instead of the standard Linux microkernel. That means you can't simple load the right module when you need it. If you want to use the wireless receiver you'll have to compile your own kernel with the xboxdrv module built in.

nathris said:
While you're right that theoretically any USB device can work, you still need the right drivers. The problem is that Android uses a monolithic kernel instead of the standard Linux microkernel. That means you can't simple load the right module when you need it. If you want to use the wireless receiver you'll have to compile your own kernel with the xboxdrv module built in.
Click to expand...
Click to collapse
Nope no wireless reciver. Just the plain old xbox 360 controller, with the usb. Why would I go a round about way of using the wireless receiver instead of just the controller?

HaiKaiDo said:
Nope no wireless reciver. Just the plain old xbox 360 controller, with the usb. Why would I go a round about way of using the wireless receiver instead of just the controller?
Click to expand...
Click to collapse
I haven't tried it on my kindle fire, but I have tried it on my xoom. Works fine. I will give it a shot in a few hours when work slows down, but I dont' see why it wouldn't work, so long as the emulator supports gamepads, and the rom/kernel does the usb host stuff.
update: Nope. controller never lights up, looks like it isn't even there. this was using the motorola OTG cable, aokp rom with the 3.0 kernel.

ffttgghh said:
I haven't tried it on my kindle fire, but I have tried it on my xoom. Works fine. I will give it a shot in a few hours when work slows down, but I dont' see why it wouldn't work, so long as the emulator supports gamepads, and the rom/kernel does the usb host stuff.
update: Nope. controller never lights up, looks like it isn't even there. this was using the motorola OTG cable, aokp rom with the 3.0 kernel.
Click to expand...
Click to collapse
You do have to use a powered usb hub with it. you did that right?

HaiKaiDo said:
You do have to use a powered usb hub with it. you did that right?
Click to expand...
Click to collapse
I didn't on my xoom, and it recognized it, so I didn't think to use one with the fire. I don't have a powered usb hub, so I can't be of any more help.

ffttgghh said:
I didn't on my xoom, and it recognized it, so I didn't think to use one with the fire. I don't have a powered usb hub, so I can't be of any more help.
Click to expand...
Click to collapse
yeah the xoom can supply power. the KF cant. Thanks for trying tho

can someone recommend powered usb hub? i have 2 and neither one work. i have tested usb keyboard and mouse w/o hub and all seems good. just need a hub for thumb drive\BT\game controller test.

HaiKaiDo said:
Nope no wireless reciver. Just the plain old xbox 360 controller, with the usb. Why would I go a round about way of using the wireless receiver instead of just the controller?
Click to expand...
Click to collapse
Its the same driver...

leroy641 said:
can someone recommend powered usb hub? i have 2 and neither one work. i have tested usb keyboard and mouse w/o hub and all seems good. just need a hub for thumb drive\BT\game controller test.
Click to expand...
Click to collapse
http://www.amazon.com/dp/B005P2BY5I/ref=pe_175190_21431760_M2C_SC_dp_1
Is what I just got and it works well.

Any rom that can enable KF using OTG?

Six axis controller help.

Argh so I'm following these guides to the letter and I still can't get this to work.
I've got everything installed correctly , I change the Master address for the controller on my PC, everything goes fine up until I unplug the controller from the PC and hit the Power button on the controller for it to pair with my phone. all 4 lights just flash on the controller and eventually go off and do nothing. Now while that happens, the phone says "Client connected:1" like its suppose to. But the controller is not connected and will not do anything at all.
I than plug it back into the computer and it seems whenever I unplug it, the master change doesn't save and it goes back to its default BT address.
I'm assuming the problem is because the master won't stick OR that's just because the controller isn't connecting to the device so it resets itself to its last known use? Thing is, the controller is brand new and has never been used on a PS3 since I don't own one.
Anyone have any insight on this? Spent $35 for the controller and another $2 for the app and can't use it at the moment :/
NOTE: My phone is the sprint GSIII despite what my sig says due to build.prop changes
EDIT: the compatibility checker indicated its compatible.
Do I need a USB OTG cord to connect it for the controllers first time being synced to a device maybe? Don't have a ps3 to connect it to unfortunately.

little bump, i have no useful information other than i read there was a way to pair the 2 using only the phone, not sure where i saw it tho, maybe on a youtube video on setting up sixaxis?
Im very interested to see if this works, as i want very badly to play n64 and other games on my projector with the mhl adapter, instead of having to use the usb for the controller, i would try it but don't own a sixaxis controller atm.

I did it with the otg cable with out a pc took me a minute to get but it worked. so I unplugged it. It is now wireless so I tried to Play dead trigger and a couple of other games and the controls wouldn't work right I was able to control the phone from the ps3 controller but no games and with the controller plugged in via otg cable games worked great
Sent from my SGH-T999 using xda premium

I have the AT&T version but I am sure they both work the same way.
Make sure you grab the correct bluetooth address from your phone, says it at the bottom of the phone in the app.
Then download the drivers and sixaxis pair tool application on the PC, make sure they are installed! Grab your PS3 dualshock controller and connect it to your PC. It should go through installing the drivers/making sure you have them installed, once its complete your current controllers master will be shown at the top. You need to change it so that it reads the same as your mobile phones address.
Once that is complete go back to your phone, open up the program and start the driver, now hold the ps button until you see it sync, if it isn't syncing then you have a problem with the address of either your phone or controller.
Or...
You can actually make a cheap OTG cable yourself with stuff you probably have laying around the house. All you need is an USB extender cable and a micro USB cable, along with some wire and a soldering kit.
http://forum.xda-developers.com/showthread.php?t=1076767

When I used the app with my nexus s I had to use the computer tool, now with the galaxy all I had to do was plug it in with an otg cable, pair, and make sure you change the input method. Now I just start the app, press start on the app turn the controller on and it pairs instantly.

mastarifla said:
I have the AT&T version but I am sure they both work the same way.
Make sure you grab the correct bluetooth address from your phone, says it at the bottom of the phone in the app.
Then download the drivers and sixaxis pair tool application on the PC, make sure they are installed! Grab your PS3 dualshock controller and connect it to your PC. It should go through installing the drivers/making sure you have them installed, once its complete your current controllers master will be shown at the top. You need to change it so that it reads the same as your mobile phones address.
Once that is complete go back to your phone, open up the program and start the driver, now hold the ps button until you see it sync, if it isn't syncing then you have a problem with the address of either your phone or controller.
Or...
You can actually make a cheap OTG cable yourself with stuff you probably have laying around the house. All you need is an USB extender cable and a micro USB cable, along with some wire and a soldering kit.
http://forum.xda-developers.com/showthread.php?t=1076767
Click to expand...
Click to collapse
Yeah I got everything down but for some reason the controller isn't saving the master change. As soon as I unplug it from the PC after changing it, it goes right back to its default master. I continue to press the button on it anyway to pair with my phone and my phone said Client connected: 1 like its suppose to, but the controller lights just keep flashing another 5 seconds and it shuts off.
Assuming the master change isn't working. Tried both the new and old .exe's on the dev's site for the PC pair tool. :/
So if I get an OTG cord, I can do the initial pair with that and than it will pair wirelessly from there on out or I have to always use it with the cord that way?
Thanks guys.
Sent from my GT-I9000 using xda app-developers app

enjoy, skip to 3min mark, he also explains how to get the controller to work with games that don't have controller support

nonmindo said:
enjoy, skip to 3min mark, he also explains how to get the controller to work with games that don't have controller support
Click to expand...
Click to collapse
Isn't a valid link
EDIT: got the link to work after all, and god its so easy with a OTG cable... hahah. Guess that's my best bet since this thing keeps being so stubborn about saving the master change when I do it on the PC. -.-
Sent from my GT-I9000 using xda app-developers app

Ironically I tried the to pair the ps3 tool yesterday too.While the compatibility tester says it works yet I can't pair.I changed the Bluetooth address and installed the driver it just doesn't work.

Ironically I tried the to pair the ps3 tool yesterday too.While the compatibility tester says it works yet I can't pair.I changed the Bluetooth address and installed the driver it just doesn't work.
Click to expand...
Click to collapse
Ah sorry to hear that, glad I'm not alone though.. Overnighted a otg cable since I don't have the parts needed to make my own haha
Sent from my GT-I9000 using xda app-developers app

SemiGamer said:
Yeah I got everything down but for some reason the controller isn't saving the master change. As soon as I unplug it from the PC after changing it, it goes right back to its default master. I continue to press the button on it anyway to pair with my phone and my phone said Client connected: 1 like its suppose to, but the controller lights just keep flashing another 5 seconds and it shuts off.
Assuming the master change isn't working. Tried both the new and old .exe's on the dev's site for the PC pair tool. :/
So if I get an OTG cord, I can do the initial pair with that and than it will pair wirelessly from there on out or I have to always use it with the cord that way?
Thanks guys.
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
Have you tried using another PC program like MotionJoy? Downloading their drivers to see if you can change the master address with it instead? That would be my next suggestion if you are having issues with the master not sticking, obviously the best option would be to connect it to a PS3 first to make sure you at least have a default master.
If this doesn't work let me now, I'll try to think up some other ways before you have to purchase a cable to make it work.

mastarifla said:
Have you tried using another PC program like MotionJoy? Downloading their drivers to see if you can change the master address with it instead? That would be my next suggestion if you are having issues with the master not sticking, obviously the best option would be to connect it to a PS3 first to make sure you at least have a default master.
If this doesn't work let me now, I'll try to think up some other ways before you have to purchase a cable to make it work.
Click to expand...
Click to collapse
Yeah I tried motion joy and the controller works great wired to the computer (Works on the PC I mean) but I don't have a Bluetooth adapter for my PC to pair it with unfortunately.
Note that whenever I sync the controller to MotionJoy, I'm unable to use that USB port with SixaxisPairTool because MotionJoy drivers were installed with that port and motionjoy instantly picks it up and makes it unrecognizable to the sixaxistool program (Uninstalling motionjoy solves this) but just thought I'd throw it out there.
I clicked BluetoothPair in motionjoy and the BT address shows different than the one Sixaxistool shows, when I choose Custom Master or whatever it says and type in my phones, it "changes" it on the screen and says it changed, I than unplug it from the PC and start the app on the phone, Press the PS button on the controller and the 4 lights blink, the phone says Client connected:1, but the lights all keep blinking and than shut off. If pressed again the blink than turn off. I than connect it back to the PC and the BT address is shown as the default one from before I choose custom.
Pretty much the Change Master only stays while its connected to the PC, soon as I unplug it the master resets. I verified that by changing it, closing the programs (Both motionjoy and sixaxistool, at separate times of course during their own individual attempts) and than reopen either program and it shows what I changed it to still. But like I said as soon as the cord comes out it resets.
Sorry for the wall of text, just trying to provide as much info as I can. I ordered a cable but that can always come in handy anyway and I'd like to see if we could still solve this without one maybe to save some cash for anyone that has this problem in the future ya know!
Sent from my GT-I9000 using xda app-developers app

I know there was an issue with MotionJoy with having to put the address in "backwards" before it paired, I don't know if that was fixed or if that is still an issue. It's odd that it works fine when you plug it in to the PC but once you try wireless, it resets... I guess it's because you have yet to use the controller AS a bluetooth device, it has always been a wired connection. So you either have to pair it with a ps3, or with another bluetooth device.
Maybe you should just wait on the cable haha

mastarifla said:
I know there was an issue with MotionJoy with having to put the address in "backwards" before it paired, I don't know if that was fixed or if that is still an issue. It's odd that it works fine when you plug it in to the PC but once you try wireless, it resets... I guess it's because you have yet to use the controller AS a bluetooth device, it has always been a wired connection. So you either have to pair it with a ps3, or with another bluetooth device.
Maybe you should just wait on the cable haha
Click to expand...
Click to collapse
Hahah yeah I pulled enough of my hair out and gave in on the cord thanks for trying though! I agree its probably related to being a new unused controller.
Sent from my GT-I9000 using xda app-developers app

Argh okay got the cord. Controller works fine as a game pad. Works flawlessly on ShadowGun and Dead trigger which both have game pad function built in.
Can not get it to connect via Bluetooth still..
Tried exactly what the video showed and such.
Only thing I can think of is the controller could possibly be dead? Which I doubt because all the trouble shooting I've been doing (Connected to PC for an hour trying to get motion joy to go, connected to my phone the past 15min, I even plugged the USB into my wall adapter for my phone to see if it charged. Lights just blink than go off after like 5minutes. That mean its charged or what? Don't have a ps3, does it need one to charge? :/
Sent from my GT-I9000 using xda app-developers app

SemiGamer said:
Argh okay got the cord. Controller works fine as a game pad. Works flawlessly on ShadowGun and Dead trigger which both have game pad function built in.
Can not get it to connect via Bluetooth still..
Tried exactly what the video showed and such.
Only thing I can think of is the controller could possibly be dead? Which I doubt because all the trouble shooting I've been doing (Connected to PC for an hour trying to get motion joy to go, connected to my phone the past 15min, I even plugged the USB into my wall adapter for my phone to see if it charged. Lights just blink than go off after like 5minutes. That mean its charged or what? Don't have a ps3, does it need one to charge? :/
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
Is this an OEM Sony Controller? Chinese fakes aren't going to work. Same thing with Wii remote clones.

kronium said:
Is this an OEM Sony Controller? Chinese fakes aren't going to work. Same thing with Wii remote clones.
Click to expand...
Click to collapse
I think its OEM? How would I go about checking?
It was this one:
www.amazon.com/gp/aw/d/B0015AARJI/ref=mp_s_a_1?qid=1341986008&sr=8-1
But it wasn't the Amazon seller by default when I got it, it was a seller named Wireovia, they've got 4.8 stars with 3559 ratings so I didn't really think much of them being fakes? Price was $39 though I don't see them in the list of sellers now, but they were default before.
Also the controller didn't come with a cord, is that a sign of a fake or is that the same with Sony's official?
Sent from my GT-I9000 using xda app-developers app
EDIT: Well crap. I was looking at "How to spot a fake" guides and they mention two definite ways of telling, one being the battery inside is different and another being there is no screw under the sticker on the back on the official, whereas the fakes have a screw under there.
Now mine has what looks to be a screw without a screwable head on it under the sticker. Maybe the new fakes have the head of the screws taken off because they knew it gave it away? Idk. Going to take it apart tomorrow and see the battery.
Anyone know if its possible to return an opened item? Purchased June 29th received it on July 3rd. It came with an amazon lable saying "Returning is easy, go to our website blah blah blah" but mentioned it being unopened. Hmm..

Call Amazon's 800 number and tell them this isn't a genuine controller, and is giving you pairing difficulties. You don't have to say what kind. Ha ha. You should get your money back no problem.

Can others on the Canadian gsiii variants download the Sixaxis app from the market? Play thinks it's not compatible with my device (d2can / rogers).

I remember from before this app had issues working on devices running sense or touchwiz ui and I had problems with it on my stock vibrant and sgs2 but it runs well on aosp based roms.so today I flashes aokp r3 and low and behold it works now! Played
Dead trigger flawlessly earlier.T-Mobile sgs3 btw.

[Q] Does the Fire TV support USB storage/powered USB splitters?

Just a quick question for anyone who already received their Fire TV (Mine will be here Wednesday hopefully)
I see that people have had success in getting everything from mice/keyboards/etc working with their Fire TV, but I'm curious if powered USB hubs and external USB drives work as well.
Ultimately I'd like to have something along the lines of a USB keyboard/mouse as well as an XB360 controller, as well as a USB slot that I can throw some media on if I have a friend over who doesn't want to set up their machine/share on my network and we can still watch something through either XBMC or Plex.

TooSlo said:
Just a quick question for anyone who already received their Fire TV (Mine will be here Wednesday hopefully)
I see that people have had success in getting everything from mice/keyboards/etc working with their Fire TV, but I'm curious if powered USB hubs and external USB drives work as well.
Ultimately I'd like to have something along the lines of a USB keyboard/mouse as well as an XB360 controller, as well as a USB slot that I can throw some media on if I have a friend over who doesn't want to set up their machine/share on my network and we can still watch something through either XBMC or Plex.
Click to expand...
Click to collapse
I was able to plug in a USB 3 hub, unpowered, and used a keyboard and mouse at the same time.

rooobbbbb said:
I was able to plug in a USB 3 hub, unpowered, and used a keyboard and mouse at the same time.
Click to expand...
Click to collapse
With a non powered usb hub I was able to hook up a mouse,keyboard,wired 360 controller. Hopefully that answers your question

What about USB storage? Can you guys read movies files from a flash drive or USB hard drive?
-Sent from my TMO Samsung Galaxy Note 3 using Tapatalk

no drive support yet, hoping someone can figure out how to enable it

movie
Hi
Can we watch some avi mkv mpeg movie on firetv directy on usb key?

saerdryl2 said:
Hi
Can we watch some avi mkv mpeg movie on firetv directy on usb key?
Click to expand...
Click to collapse
saerdryl2,
Please take the minimal amount of time to read the responses from others as this has been answered... Most recently right above your post:
screwyluie said:
no drive support yet, hoping someone can figure out how to enable it
Click to expand...
Click to collapse

Ordered an Ouya that hasn't arrived yet and considering return/refuse.
Does anyone have any information for the future of FTV USB storage?
ie:
Is it not possible with the current hardware?
Is it a feature that is under development and will likely be enabled in the near future?

i8nt said:
Ordered an Ouya that hasn't arrived yet and considering return/refuse.
Does anyone have any information for the future of FTV USB storage?
ie:
Is it not possible with the current hardware?
Is it a feature that is under development and will likely be enabled in the near future?
Click to expand...
Click to collapse
Most likely not a hardware issue, but the software distributed with the device by Amazon does not support it. I think they want you to use their cloud services instead.
Most likely fixable once Root is available, but currently there is no distributed Root available yet. Most likely will see Root available after the device gets 4.43 updates.

Thanks, the hdd is a must have for Mashup's direct download, instead of using a dvr.
Since I got the Ouya on the cheap, will probably keep it for now.

I see the xbmc wiki says usb storage can be enabled with root.
Sent from my GT-I9300 using Tapatalk

Confirmed it's working. Just root + sideload StickMount.
Sent from my GT-I9300 using Tapatalk

nadimsoze said:
Confirmed it's working. Just root + sideload StickMount.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
So, just to confirm, you are using a USB Hub to get all three USB items? Keyboard/mouse, controller AND external storage?
need to get that last part clear..

Nope. Didn't try that. Just the 2.5" usb 500gb external.
Sent from my GT-I9300 using Tapatalk

Vylle said:
So, just to confirm, you are using a USB Hub to get all three USB items? Keyboard/mouse, controller AND external storage?
need to get that last part clear..
Click to expand...
Click to collapse
I have a simple 4 port unpowered USB 2.0 hub connected to my Fire TV at all times. In that hub is a 64GB NTFS thumb drive at all times that is mounted via StickMount on boot. When I need to, I plug a USB mouse and keyboard into two of the 3 open USB ports on the hub. Everything works with all 3 devices plugged into the hub. I hope that's the info you're looking for.

fireTVnews.com said:
I have a simple 4 port unpowered USB 2.0 hub connected to my Fire TV at all times. In that hub is a 64GB NTFS thumb drive at all times that is mounted via StickMount on boot. When I need to, I plug a USB mouse and keyboard into two of the 3 open USB ports on the hub. Everything works with all 3 devices plugged into the hub. I hope that's the info you're looking for.
Click to expand...
Click to collapse
thanks - this is all i need to know
now to go off to amazon n get one

Which usb hub are you using? I'd like to order one from Amazon, along with a 128GB stick.
fireTVnews.com said:
I have a simple 4 port unpowered USB 2.0 hub connected to my Fire TV at all times. In that hub is a 64GB NTFS thumb drive at all times that is mounted via StickMount on boot. When I need to, I plug a USB mouse and keyboard into two of the 3 open USB ports on the hub. Everything works with all 3 devices plugged into the hub. I hope that's the info you're looking for.
Click to expand...
Click to collapse

I don't know if that's disk related, but I have an old LaCia external 2.5" 500Gb HDD. It has a regular USB2 port and an additional 5V in which can be used optionally (if attached to the computer, it works with just the USB).
With the AFTV, I had to use the additional 5V.
A friend of mine is having the same issue with his external HDD, the power from AFTV is not enough

Hi,
I read that Fire TV doesn't support USB storage, but I believe it does although I've not been able to access a drive (plugged in to powered hub) yet. So far using sideloaded es file explorer I can see the USB device and alongside it the drop down button which when clicked seems to unmount the drive. Looking in the dmesg log (familiar to Linux users I'm sure) the kernel loads appropriate USB driver module and the recognises the USB storage the device as /dev/sda with partition sda1. There is also an entry in the list of mount points for /storage/usb, but it seems to point to 'tmp, tmp' which doesn't make much sense to me. It seems to me the only thing missing is automount of the recognised partition, does anyone agree or disagree? Does anyone know a way of mounting on an uprooted device (l'm on the latest update and would prefer not rooting unless unavoidable).

I've been using this one without issue: http://goo.gl/yXFV9o