After installing "Cyanogenmod 7 by Quarx", I flashed my Defy with "Hong Kong/Taiwan JRDNEM_U3_2.59.0" by RSD Lite, my phone now does not response to any button, cannot be powered on, and not response to VOL-UP + POWER.
However, RDS Lite can still recognize the phone by just plugging in the USB cable. I can flash it again (and again) with the RSD Lite without error. I tried more that 5 sbf (both 2.1 and 2.2), none of them change the situation.
The sbf "Hong Kong/Taiwan JRDNEM_U3_2.59.0" has saved my phone once before installing CM7 by Quarx, but it doesn't work for me now.
Please help :
Could any one tell me how to do now ? which sbf I can use now ?
I should have my phone bootable again at first.
Did u wipe in Stock Recovery and than flash the sbf or without wipe..?
Sorry for English
Before flash the sbf, I wiped in clockworkmod recovery. At that time, CM7 can boot and I can enter recovery during the phone boots.
My Defy is "completely" bricked now
I just flashed the Defy_2_2_CN.sbf refered by http://forum.xda-developers.com/showthread.php?t=923360. RSD Lite now cannot recognize the phone any more.
Vol-Up + Power, then battery-in does not work for me before and after flashing he Defy_2_2_CN.sbf. As RSD Lite cannot recognize the phone, so no flashing any more, completely bricked now !
-Go into the system recovery with "vol down + power".
-Then when you see the android update guy press vol down + vol up at the same time.
-Wipe your phone + factory reset.
-Reboot and hold "vol up + power"
-You are now into bootloader mode, reflash the system with RSD Lite and a sbf you like
ifu said:
-Go into the system recovery with "vol down + power".
-Then when you see the android update guy press vol down + vol up at the same time.
-Wipe your phone + factory reset.
-Reboot and hold "vol up + power"
-You are now into bootloader mode, reflash the system with RSD Lite and a sbf you like
Click to expand...
Click to collapse
Before "completely brick", my phone has already not responded to "vol down + power".
So many flashing... perhaps battery drained to flat now??
You checked ur battery...?
Sent from my MB525 using XDA App
Today, I just checked the battery voltage, it is very low, 3.2V. I am charging it up with now.
Now, I wonder if it is the battery issue, a full battery brings me the state of "can be recognized" only (and I can continue to flash and flash ...), still I cannot boot up.
wyumhk said:
Today, I just checked the battery voltage, it is very low, 3.2V. I am charging it up with now.
Now, I wonder if it is the battery issue, a full battery brings me the state of "can be recognized" only (and I can continue to flash and flash ...), still I cannot boot up.
Click to expand...
Click to collapse
Charge it 100% and try the steps....Best of Luck
Sent from my MB525 using XDA App
I charged the battery to 3.9V, the phone can be recognized, then I flash it with the 3.4.2_177-005_NORDIC.
During reboot, Moto log showed, and then "android" appeared, but kept in this screen for more than 10 minutes. "android" flashed once every 10 seconds.
I remove the battery, plug-in again and try to enter the recovery mode:
1. "vol-down + power", a triangle with android appear.
2. tap the right-bottom with and without vol key has no effect.
What can I do now ?
First wipe data factory reset in stock recovery and reboot from ther volume up and than flash sbf....it works for me...For u?
Sent from my MB525 using XDA App
I cannot enter stock recovery now, how to wipe / reset ?
Are my procedures correct :
1. "vol-down + power" until a triangle with android appear.
2. tap the right-bottom of the screen with/without vol key
wyumhk said:
I cannot enter stock recovery now, how to wipe / reset ?
Are my procedures correct :
1. "vol-down + power" until a triangle with android appear.
2. tap the right-bottom of the screen with/without vol key
Click to expand...
Click to collapse
Procedures is correct, Try another time it mostly works...
wyumhk said:
I cannot enter stock recovery now, how to wipe / reset ?
Are my procedures correct :
1. "vol-down + power" until a triangle with android appear.
2. tap the right-bottom of the screen with/without vol key
Click to expand...
Click to collapse
Actually if this is a 2.2 ROM, which I believe it is, try using volume up and down at the same time once in recovery and you see the triangle. You no longer tap the screen.
Yes, it works.
After wipe / reset, my phone can boot up now. Even the current ROM JRDNEM_U3_3.4.2_117-002_BLUR_SIGN does not contain my language, I think I can continue to replace another ROM.
Thanks very much.
wyumhk said:
Today, I just checked the battery voltage, it is very low, 3.2V. I am charging it up with now.
Now, I wonder if it is the battery issue, a full battery brings me the state of "can be recognized" only (and I can continue to flash and flash ...), still I cannot boot up.
Click to expand...
Click to collapse
Did you used external charger to charge your battery? Or simply plugged in charger?
Sent from my MB525 using XDA App
rachit2588 said:
Did you used external charger to charge your battery? Or simply plugged in charger?
Sent from my MB525 using XDA App
Click to expand...
Click to collapse
Similar to this one :
http://forum.xda-developers.com/attachment.php?attachmentid=513020&d=1297249621
I used a lab used power supply, the voltage was adjusted to 4.2V. I also connected a resistor in series to limit the current.
i bricked once.............FIRST install all moto defy drivers and then connect ur phone.
Open RSD lite
use an .sbf that is greater than ur current version......if u dont know then go for the highest version......start flashing
SOLVED!!!!
pjgowtham said:
i bricked once.............FIRST install all moto defy drivers and then connect ur phone.
Open RSD lite
use an .sbf that is greater than ur current version......if u dont know then go for the highest version......start flashing
SOLVED!!!!
Click to expand...
Click to collapse
After flashing many 2.1 and 2.2 sbf, my Defy can be powered on by these 2 versions only (others do not response to power button any more) :
1. JRDNEM_U3_3.4.2_117-002_BLUR
2. JRDNEM_U3_3.4.2_177-005_NORDIC
So, "go to the same or higher version" seems to be true, but why ?
Related
I have bricked my Motorola Defy.
I have tried flashing a new ROM using RSD Lite (following this guide). It says 'complete' but my phone will not turn on. Sometimes it will just show the Moto boot logo but never fully boot up. I can only open the boot menu.
The ROMs I have tried flashing can be found here (All UK 2.1 at the top of the page).
Background - I got into this mess by attempting to flash the Gingerbread UI ROM (here).
Does anyone have any ideas? I would really appreciated any suggestions.
Thank you.
Probably you have flashed a firmware which cannot be downgraded to eclair. Try to get again in the bootloader and flash a froyo build (the official french one, for instance).
Hope this helps
Sent from my MB525 using XDA App
but supposedly it is still an éclair ROM so it shouldn't be the reason... best thing would be to flash an original 2.1 rom, I'm sure you can find one on the development section. Make sure to have a fully charged battery though - charge it on someone else's phone, for example.
It's most likely a problem with cache. Power your phone with Volume Down holded, when in recovery press Volume Up + Down, clear data/factory reset, clear cache.
rafaccb said:
but supposedly it is still an éclair ROM so it shouldn't be the reason... best thing would be to flash an original 2.1 rom, I'm sure you can find one on the development section. Make sure to have a fully charged battery though - charge it on someone else's phone, for example.
Click to expand...
Click to collapse
Hi, thanks for the reply.
I have tried using the UK ROMs here: h**p:// and-developers. com/sbf:defy but none have worked. Any other suggestions?
Thank you.
antony.ps said:
It's most likely a problem with cache. Power your phone with Volume Down holded, when in recovery press Volume Up + Down, clear data/factory reset, clear cache.
Click to expand...
Click to collapse
Hey, unfortunately I cannot get into recovery, only the boot menu. Do you have any other suggestions?
Try flashing a JRDNEM_U3_2.59.0 sbf.
ABC_Universal said:
Try flashing a JRDNEM_U3_2.59.0 sbf.
Click to expand...
Click to collapse
Thanks, I will try now. Any particular country?
ABC_Universal said:
Try flashing a JRDNEM_U3_2.59.0 sbf.
Click to expand...
Click to collapse
Hey.
I have just tried this using the Australian version from here:h**p://and-developers.com/sbf%3adefy
Unfortunately, it did not work. I still cannot boot the phone.
Thanks for your advice, do you have any other ideas?
Have you tried one of the 2.51 version roms?
like JRDNEM_U3_2.51.1 Blur or
JRDNEM_U3_2.51.0 deblur.
Kaljam
kaljam said:
Have you tried one of the 2.51 version roms?
like JRDNEM_U3_2.51.1 Blur or
JRDNEM_U3_2.51.0 deblur.
Kaljam
Click to expand...
Click to collapse
Hi, yes I have tried the UK JRDNEM_U3_2.51.1 from here. Is that the same as blur or deblur?
Thanks.
Just an update...
All ROMS I have tried have installed OK through RSD Lite. The result is always 'Finished' or 'PASS'. But then when I try to turn my phone on, it never boots up.
I really appreciate the replies so far. If anyone has any further ideas, I would love to hear them.
Thank you.
UPDATE
I have just flashed the latest froyo leaked ROM as suggested around the net. Slight progress, the phone now boots to the moto boot logo but no further?
Does anyone have any ideas from here?
Thank you.
you do know that after flashing an sbf it takes a very LONG time to boot the first time! I just hope you are not giving up after a a couple minutes of M logo and pulling the battery or something it literally takes like 5 minutes.
You said you are still able to enter bootmenu? That is not possible after flashing an sbf, as it wipes the bootmenu away! Are you talking about bootloader?
Pull the battery and immediately put it back in while holding vol down. If the phone does not turn on just by inserting the battery then continue to hold vol down and press the power button for about 3 seconds, do not let go of vol down. Continue holding vol down until stock recovery appears.
Once you're in stock recovery press vol up AND vol down at the SAME TIME. Now use the volume toggle to select wipe date/factory reset, use the power button to make your selection, then wipe cache partition. Reboot
Walk away for like 5-10 minutes and check back on it.. Theres no reason it shouldn't work
zyxwvut said:
you do know that after flashing an sbf it takes a very LONG time to boot the first time! I just hope you are not giving up after a a couple minutes of M logo and pulling the battery or something it literally takes like 5 minutes.
You said you are still able to enter bootmenu? That is not possible after flashing an sbf, as it wipes the bootmenu away! Are you talking about bootloader?
Pull the battery and immediately put it back in while holding vol down. If the phone does not turn on just by inserting the battery then continue to hold vol down and press the power button for about 3 seconds, do not let go of vol down. Continue holding vol down until stock recovery appears.
Once you're in stock recovery press vol up AND vol down at the SAME TIME. Now use the volume toggle to select wipe date/factory reset, use the power button to make your selection, then wipe cache partition. Reboot
Walk away for like 5-10 minutes and check back on it.. Theres no reason it shouldn't work
Click to expand...
Click to collapse
Hey,
I have just got back from dropping of the phone with T-Mobile - Damm!!!!!!!
Thanks for the detailed explanation. I must have talking about the bootloader. Not the menu. I will head back to the shop in the morning and collect it back off them. Hopefully as it is a Saturday they have not sent it off?
Sooooo frustrating!!!!!!!!
I will update you when I have got it back and tested the above.
Thanks again,
Chris.
LOL I know what you mean... I had instant heart failure the first time I was stuck in a bootloop!!! Thought I wasted $400
I just panicked and gave up.. damm! Loads of people have said that its almost impossible to brick a defy. Fingers crosses thats true!! Lol
First, sorry for my english.
I have a similar problem. I flashed the official french froyo.
First it runs good. But today, two days later, the defy reseted automaticaly.
Several times.
Then I did a wipe. At the end the defy reseted automaticaly and stopped at the motorola logo. I flashed again. At the end of the flash, when RSD boots the defy, it stopped at the logo again. After...it must have been 15 minutes I pulled the battery and tried to get into the bootloader for a wipe.
But I can't enter the bootloader (vol up + power). The motorola logo appears and nothing happens. The last time I waited over 30 minutes.
OK, I have my phone back from T-Mobile...here it goes!!! (fingers crossed).
EDIT
Battery is out - will re-charge with the USB cable trick..
zyxwvut said:
you do know that after flashing an sbf it takes a very LONG time to boot the first time! I just hope you are not giving up after a a couple minutes of M logo and pulling the battery or something it literally takes like 5 minutes.
You said you are still able to enter bootmenu? That is not possible after flashing an sbf, as it wipes the bootmenu away! Are you talking about bootloader?
Pull the battery and immediately put it back in while holding vol down. If the phone does not turn on just by inserting the battery then continue to hold vol down and press the power button for about 3 seconds, do not let go of vol down. Continue holding vol down until stock recovery appears.
Once you're in stock recovery press vol up AND vol down at the SAME TIME. Now use the volume toggle to select wipe date/factory reset, use the power button to make your selection, then wipe cache partition. Reboot
Walk away for like 5-10 minutes and check back on it.. Theres no reason it shouldn't work
Click to expand...
Click to collapse
Hey, I am still have issues...
I have charged it up but cannot access recovery. I have tried taking out the battery and putting it back in while holding vol down but no luck. I have also tried holding the power button as well like you said.
I am going to leave it charging even longer to see if that helps.
Hi, i messed up my phone in a really stupid way
So, until a few days ago i had a froyo installed on my phone ( + 3.4.2_155-002_DEBLUR_SIGN ROM) but then i decided to give a try to CyaongenMod Beta 5.1.
I followed this very well detailed installation guide http://forum.xda-developers.com/showthread.php?t=1054447 and got my CM7 working, but after a day i became unhappy with the CM7, the camera didnt work properly and there were many other issues.
What I did next, I turned my phone off, went into stock android recovery and did a full factory reset and cache wipe. I rebooted the phone and hoped that i would be able to load a normal android system, but the only thing that is happening is a motorola logo being displayed.
I tried connecting my phone via USB to flash an old ROM (3.4.2_155) but the phone is not appearing in the RSD Lite - i think it has to be completely turned on in order to appear there, isnt is true?
What shall i do to be able to turn my phone on properly, and is it possible to flash another working rom via RSD lite without having my phone turned on?
i tried to factory reset + wipe with stock and custom recovery, still no luck, phone freezes at motorola logo during start up.
i dunno why it still doesnt show up in RSD lite, any tips on how and when should i try connecting it via USB cable?
EDIT I forgot that for a phone to appear in RSD Lite without being switched on it has to be in a bootloader mode!! (which is entered by holding a volume up button during strart up, just like volume down button for recovery! i know, im stupid, i don't know how i could forget about this)
So, i entered the bootloader menu and managed to have my phone seen by RSD Lite, next I flashed a new SBF and I was getting a bootloop, and fixed it by a data wipe in stock recovery!)
Try to take out battery after few minutes put it back. Pull in usb cable. Then try to push the right buttons.
SOLUTION
First get your phone in bootloader mode by pressing VOLUME UP first and then POWER button till you get that logo.......Then flash it with rsd lite..,,,
pjgowtham said:
First get your phone in bootloader mode by pressing VOLUME UP first and then POWER button till you get that logo.......Then flash it with rsd lite..,,,[/QUOTĘ]
Yes, I forgot about it... Too much marihuana in my life hehe
Greetings , sent from my working defy
Click to expand...
Click to collapse
I have to firstly say I am a complete noob, infact, the Defy is my first smartphone.
So far i have......
Rooted Phone
Performed a nandroid backup
Installed 2nd init
Installed CM7
Everything was going so well until i noticed there were no google apps. I installed gapps zip file after re installing recover (to install the zip file from boot menu). Ever since then, my phone wont make it past the red Motorola logo. I cant even get back into the boot menu?
Please Help
If you have 2nd Init installed , press Vol Down whenthe blue LED blinks during startup.
If that fails, hold the Vol Down button and then power on your cell, you'll enter default recovery. Clear cache/data and start again.
Also, if you are using CM7 RC1 or above, there should be no need to install gapps.zip separately.
Thanks for the reply mate.
Phone wont get to blue light before freeze. RE the vol down power on menu, all i get is an android dude with a triangle with an Exclamation point in it?
sorry i should have written this in my first reply, when you see the exclamation point, press Vol Up + vol down TOGETHER, and you'll see the recovery menu.
JimmyMagic said:
Thanks for the reply mate.
Phone wont get to blue light before freeze. RE the vol down power on menu, all i get is an android dude with a triangle with an Exclamation point in it?
Click to expand...
Click to collapse
at this point press vol up and down at the same time..and wipe
The only options i get on there are.....
Reboot system now
Apply sdcard:update.zip
Wipe data/factory reset
Wipe cache partition.
Tried them all and no luck
try this one
http://forum.xda-developers.com/showthread.php?t=1147967
in the 4th post, you can try that and flash it again
Never ending problems mate. Cant get RSD lite to work.
Keep getting.....
"failed flashing process. Failed flashing process. unable to retrieve initialization values from INI file"
Running as administrator and have tried 2 different SFB files.
Im giving up all hope, been reading forums all day and my eyes are starting to hurt.
bikerabhinav said:
If you have 2nd Init installed , press Vol Down whenthe blue LED blinks during startup.
If that fails, hold the Vol Down button and then power on your cell, you'll enter default recovery. Clear cache/data and start again.
Also, if you are using CM7 RC1 or above, there should be no need to install gapps.zip separately.
Click to expand...
Click to collapse
I installed CM7 RC1 and market etc werent there.
Don't give up hope yet, people have recovered their Defy from even worse conditions. All this could be an outcome of a chain of mistakes so lets stat from scratch.
1. Is your battery charged? Does it show charging LED when plugged in wall charger while turned OFF ?
2. Which OS do you have? also 64bit or 32?
3. Which Motorola Driver and RSDLite version do you have?
4. Where did you download the SBF files from? paste the link to that thread.
5. How are you flashing the SBF? (what steps do you take)
Also, try this:
Pull out the battery, Hold Defy in your one hand and press Vol Up+Down+Power button all together. Now, quickly insert the battery with the other hand keeping those buttons pressed and you will be taken to stock recovery.
Only Wipe data and wipe cache, do not install update.zip or anything else.
Once done restart the cell and let us know what happens.
JimmyMagic said:
Never ending problems mate. Cant get RSD lite to work.
Keep getting.....
"failed flashing process. Failed flashing process. unable to retrieve initialization values from INI file"
Running as administrator and have tried 2 different SFB files.
Im giving up all hope, been reading forums all day and my eyes are starting to hurt.
Click to expand...
Click to collapse
thats a common problem related to the version of RSDlite..
use 5.3.1 and try to flash again..
All the best
Got it sorted at last. Just needed RSD Lite 4.9.
Still had issues after, but managed to sort em out by installing CM7 then Gapps, rebooting then factory resetting data and cache.
A long struggle, but got there in the end.
Many thanks to everyone who helped me out, I am so grateful.
can u tell me which SBF u used that worked? any link ?
rangapsr said:
can u tell me which SBF u used that worked? any link ?
Click to expand...
Click to collapse
Use 3.4.2 177-005 Nordic http://forum.xda-developers.com/showthread.php?t=1037076
http://forum.xda-developers.com/showthread.php?t=1093352 this helped me...
hi
when connecting my charger to phone dont charging and ? mark on battery ,battery in bootloader is ok!
i use some 2.2 ram , my defy always waiting on motorola logo
please help
who i see my batery has dead wihteout charger or use other battery?
i havent any battery for test
please help
If you have not done so already pull the battery and replace. It happened to me once, and a battery pull allowed it to charge again. It that doesn't work I would suggest trying a different battery.
not away whithout use other battery ?
i dont have anthoer
i only one have defy in my city!and buy online battery in my country not sure and very expenseive
i think battery is fine because in bootloader is ok and can flash but problem from software of phone and dont solution with flash and wape because i do flash /wape /cashe veryhigh with multi 2.2 rams
sorry my english is weak
Hi, friend
How about your Defy, it's working or not?
Could you try the universal battery charger?
http://www.youtube.com/watch?v=yyJu6aXXUu8
It should help...
Pull the batt plugin the charger...
Turn the charger on... hold yhe volume down button while doing this... ull see recovery screen wipe data...
Pull the charger put the batt in n try...
Sent from My Mind using the Brainwaves...
I think thats not a prob did u flash full sbf or fixed one??
Sent from My Mind using the Brainwaves...
thanks friends
my defy now stuck in m logo and not charging battery , when connect charger question mark on battery and not charging with universal charger but in bootloader battery is ok
i flashed multiple(more than 8) with different 2.2 rams and wape data/cache and not have any Advantage
i think this problem not resolvable with full flash and wape it has another way
now way???
I have exactly same problem. It's USA defy. I flashed full sbf with 2.2.1 nordic rom. Then I tried CygeonMod rom. But first time boot never worked. Then I decided to flash the nordic rom. So I did wiping from customer recovery. And I tried to flash the nordic and i got this. But I am not sure 100% since I was reading multiple things. But I got feeling that custom recovery partition is still there and that partition is not allowing the phone to boot. When you do the Power Button and Vol Down you can go to original recovery mode. And the you do full cleaning and wiping. But same thing. no result....
chinbold said:
I have exactly same problem. It's USA defy. I flashed full sbf with 2.2.1 nordic rom. Then I tried CygeonMod rom. But first time boot never worked. Then I decided to flash the nordic rom. So I did wiping from customer recovery. And I tried to flash the nordic and i got this. But I am not sure 100% since I was reading multiple things. But I got feeling that custom recovery partition is still there and that partition is not allowing the phone to boot. When you do the Power Button and Vol Down you can go to original recovery mode. And the you do full cleaning and wiping. But same thing. no result....
Click to expand...
Click to collapse
You should always wipe from Stock Recovery before flashing an SBF.
* make sure your phone is charged
* boot into Stock Recovery (power + vol down)
* do "wipe data/factory reset" and "wipe cache" (Make sure that you wipe BOTH /data and /cache via stock recovery)
* Reboot from Stock Recovery with power + vol up pressed to enter Bootloader Mode
turn phone on holding the power button and the volume-up button for 5 secconds. Let go and it should be a black scree with some white text
* Then connect your phone via usb
* open RSD Lite and flash
Hey thanks for the tip. Will do your way now on.
Also I found the solution to the problem. Defy giving a "?" battery message because it thinks there is no battery since there is no juice inside the battery. One bad thing with defy is that Motorola, I guess, never think of case where you need to charge the battery in "Stock Recovery" or "Boot loader" or even loading the firmware. I think, this is Motorola's designing flaw. Hope the newer motorola phones are not like this. I will use the universal charger that I have at my office and the once the battery has enough then I will apply the stock rom. But if you don't have any universal charger the following is the right place:
http://forum.xda-developers.com/showthread.php?t=892026&highlight=battery+low+cannot+program
Hello,
I sent my phone for service and was told that the problem of my phone they do not cover, and the note says that the board is warped, bent, I thought it was bricked, only saw a light, could not boot and the device has no reaction , already tried the battery mode but to no avail,
What is the solution? D;
I hope you understand, I'm from Brazil
cheuslacerda said:
Hello,
I sent my phone for service and was told that the problem of my phone they do not cover, and the note says that the board is warped, bent, I thought it was bricked, only saw a light, could not boot and the device has no reaction , already tried the battery mode but to no avail,
What is the solution? D;
I hope you understand, I'm from Brazil
Click to expand...
Click to collapse
Desculpe amigo, no entiendo.
As far as I understood you, your phone is not showing you any boot screen OR there's currently no software running on your device, & I'm quite sure that your cell phone's battery is not charged enough to run the device in any mood, try searching your local mobile market for Universal Charger, charge your battery for 7-8 hours, meanwhile download RSDLite & Brazil Froyo Official SBF,after 7-8 hours then put battery back in defy, Turn your phone ON while pressing Vol UP [keep it pressed until it shows you bootloader], then open RSDLite & choose downloaded SBF, let it finish & VOILA, you're good to go again.........
PS: Defy is having locked bootloader, means whatever u do with your device, you can't brick it in any means, always it will run in Bootloader mode
U mean u can't even get into bootloader or recovery?....wat did u do jus before this happened?
Sent from my MB525 using xda premium
Did u throw the Defy to floor.. Seems the board of Phone is bend bcz of some seriuous shock ..
thanks for help
before it is the way that I could do the flash, but the last time I used a rom (Froyo) that I can not remember the way and left it,
I sent my phone to Motorola, but they included this pie plate that's my fault!
My problem is:
- Just see white LED,
- Black screen,
- Phone doesn't boot?
- Never ever see the motorola logo
McGyver Hack tried and left carrying several hours but the phone shows no signal, LED lights only when connected to USB
I hope you understand! D;
cheuslacerda said:
McGyver Hack tried and left carrying several hours but the phone shows no signal, LED lights only when connected to USB
I hope you understand! D;
Click to expand...
Click to collapse
Did you try to follow this guide: http://forum.xda-developers.com/wik...#Recover_Nearly_Bricked_Phone_.28hopefully.29 ?
If not, do so. If you see the white LED and did not do any physical damage to the phone, it should be unbrickable and with the guide from above it should work again.
universal charger works just like McGyver?
I got a charger
My charger shows that the battery is full, I still have 8 hours to leave loading?
I did do the flash, but now not out of the motorola logo! and not able to enter the factory reset
Which rom did you flash?
Normally you should be able to enter stock recovery by holding vol-, powering on, and stop holding vol- when the yellow triangle appears. Then press vol- and vol+ at the same time and wipe cache. Reboot and done.
JORLA_U3_3.4.2_107-9
I can't enter to recovery mode, just bootloader
Am I doing something wrong with RSD? to put the flash, and when it appears to manually restart it restarts but gets stuck in the Motorola logo, remove the battery and put again holding power + vol up and it appears that the RSD over this process ... right?
microsd must be empty?
I am not able to sleep because of this D;
it's not important whether the sd is empty or not.
Maybe try a more recent version of rsd lite, like 5.1. Also install the latest motorola drivers.
You may also try to check the MD5 sum of your SBF against the one given on the download page. Or download the SBF again and reflash a second time.
Did you wait for RSD to display "Reboot phone manually" or "PASS/FINISHED" ? If you're not 100% sure that it's done, simply wait for 5 minutes or so and check whether it has finished or not.
You could also try to flash a 2.2.2 rom (nordic or so).
tdlr said:
it's not important whether the sd is empty or not.
Did you wait for RSD to display "Reboot phone manually" or "PASS/FINISHED" ? If you're not 100% sure that it's done, simply wait for 5 minutes or so and check whether it has finished or not.
Click to expand...
Click to collapse
in part he is in "manually reboot phone" and hangs on the Motorola logo, it is still "manually reboot phone" even after five minutes, I pull the battery and replace and go into the bootloader, and woe in rsd lite it was "Reboot phone manually" is "PASS"
would somehow more radical? recovery by entering the pc?
my Defy is heating up, is this normal?
I had installed before the unit to CM7 problem
i make this video:
http://www.youtube.com/watch?v=1O4lALPdlKo&feature=mh_lolz&list=HL1317352132
cheuslacerda said:
i make this video:
http://www.youtube.com/watch?v=1O4lALPdlKo&feature=mh_lolz&list=HL1317352132
Click to expand...
Click to collapse
Starting at 1:05 and the next 20 seconds or so I don't really understand why you're putting the battery out and in so often. After rebooting the phone, you should simply wait for RSD to show PASS and then just wait another 2 minutes or so for the phone to boot. Why do you start it in bootloader mode again ?
Also, did you try to flash other Roms? If not, try Nordic 2.2.2 or others (but NOT 2.3.4 roms!!!!)
Btw, is it still impossible to enter stock recovery?
So ... I took the battery because the moment that appears to restart my device and manually reset it is in the motorola logo until the battery runs out, and if I call to replace and usually the rsd lite still says need to restart if I shot and put the battery and go into the boot loader shows the RSD lite "PASS"
poles already tried ROMs, including nordic
what I'm seeing is rather impossible to get into recovery, but now it appears after a few seconds after the motorola:
bootloader
09.10
Err: A5, 70,39,00,27
help!! guys!!
Did u try a new version of rsd lite?
Sent from my MB525 using xda premium
yes!! i try