Develop Bugs

Applying the screen protector -who knows how?

Who can share with us the knowledge, wisdom and techique of applying the screen protector correctly, evenly and eventually bubble free.
If we all admit it, we need help, or is it just me with the shaky hands and crooked eye?

Tomo said:
Who can share with us the knowledge, wisdom and techique of applying the screen protector correctly, evenly and eventually bubble free.
If we all admit it, we need help, or is it just me with the shaky hands and crooked eye?
Click to expand...
Click to collapse
I've applied a lot of screen protectors, but I'm no expert. YMMV. Even so, you want to start with a dust-free environment. Tiny specks of dust, if like me, you live out in the country, are as problematic as air bubbles, and a serious pain to remove. If you get one on a sticky surface, while you're removing it with scotch tape, you're also risking more little particles landing on it. It can be a never-ending nightmare and eventually leave the protector so marred with residue that it's no longer worth using on such a gorgeous device--so prevention is the best cure.
Step 1: Dust free room.
I recommend a bathroom for a dust-free setting. Well before taking anything inside, hit the shower on as hot as it goes and let it steam up the room, keep the door as closed as possible. Once it's off, the steam will cool and weigh down particles in the air. Once the room is no longer moist, carefully bring in your phone and protectors, maybe a credit card too without letting in too much outside air or new unweighted dust. Open and close the door slowly--quick movements will draw in lots of dusty air, but don't dilly-dally while getting inside either. It's time-consuming to set up, but worth it if you live in a dusty area.
Step 2: Orientation
Now you want to find a location on the phone that will allow you to orient placement of the protector. If the protector has a hole for the speaker, or light sensor or whatever--that's the end you want to start with because the more border you have to work with, the easier it will be to align it straight from the start. You're going to want to start on a narrow end so you are laying it down longwise as this will be easier to manage bubbles as you go mm by mm. Make sure your screen is completely clean (hopefully you haven't removed the original plastic covering until just now), and then peel off a little of the screen protectors' backing and orient it along a border of the phone. If you can get that part straight, the rest of the protector will go down straight as well.
Step 3: Slow Application
Now you're going to slowly peel back more and more of the backing as you slowly apply more and more of the protector. If you get a bubble as you go, back it up a millimeter and lay it down again more slowly. This is the time to use the credit card if you get a bubble that just keeps coming up in the same spot--don't wait until it's applied and try to push it out. That's a nightmare.
A good protector can last years if applied properly the first time and not abused. I use clairvue and they're very durable. I don't know about the included TP2 protector.
Step 4:Breathe
You weren't breathing while doing this were you? No wonder it sucks.

I alwaus use a bank Card.
being down en slowly slide the bank pass upward. This covers all the screen and leaves no bubbles. then do it a second time, mosliding the card upwards. Works for me most of the time. (at least, don't know if the screen is straight, or has a little angle in it?)

Mine went on without a problem...
first clean the screen of all gunk dust finger prints (yes we know you played befor putting on the screen protector) etc etc
Do this as said above in a dust free room or just have hoovered is normaly just as easy
peel the lower part of the protector off the plastic backing ... the backing they provide is quite stiff so you can use this to apply the protector
you only want to peel back around 1-2cm or about half an inch i chose the bit which goes over the buttons you may want to do the camera end first
I then used a glasses cloth but any decently fine weave cloth which is dust free will do and slowly very slowly stuck the protector to the screen and massaged the edge down peeling it off the backing as i went.
OPk re reading that it doesn't ake much sense but if you fold it over on itself using the backing to hold it off the screen and run the edges down you won't get air bubbles i found

Mild soapwater misted to the sticker and to the surface to be attached.
Then apply the sticker and align to the surface where to attach
Push the soapwater out from between the film and the surface.
NOTE: this is a general rule to apply stickers! I have no knowledge on phone shields.

nevermind i must have had a small bit sticking off the side the corner of mines just lifted and must have got a few small bits of dust in the gap ... i wonder if the adhesive is water soluble

Well I thought I'd screwed up my screen protector, but I salvaged it. It took about eight goes but it's on and working brilliantly.
Here are some salvaging tips:
1. When you're lifting the protector off, try and avoid bending any part too much. This is particularly relevant for the corners.
There are two ways of lifting the protector from the screen. The best is with sticky tape (Sellotape?) which can be applied near the corner and will be the easiest method. But if your stickky tape's rubbish, it might not lift the protector. In that case, you can carefully use the tip of a sharp knife to lift the very smallest amount you can. As you lift, you're looking to minimise the contact area by turning the knife sideways and definitely not allowing the knife's point or sharp edge touch the protector.
2. As it lifts, try and help the protector up by just holding the edges.
3. Take your time. The thing WILL drop back down a few times as you lose your grip, but just relax, take a deep breath and start again.
Once it's off:
1. Clean the phone screen.
2. fortunz and magius00 have given some great application tips elsewhere. Here what you're looking for is a perfectly clean screen with no dust.
Now. Before reapplying the protector:
1. Wash it with soap. I've used both shower gel and washing-up liquid. Wash both sides. Use your fingers to wash it.
2. Minimise contact with the "sticky side" once it's washed.
3. Rinse it well. Both sides. Clean water.
4. Don't bother to dry it. Definitely don't. You'll make it worse than ever. You can gently shake it to lose the largest drops. Both sides can have water droplets. Fear not.
As the protector goes on, try and minimise the contact around the edges whilst maximising pressure from the middle. Basically, the more secure the edges at this stage, the more difficult it's going to be to squeeze out any trapped air bubbles. Squeeze the bubbles from the centre outwards.
Once I'd done this about four (!) times, patiently putting the protector on and then gently easing it off again as some stray pube or grain of sand had found its way in between (how?), I eventually achieved an air-bubble, pube and sand-free application. The only trouble was the screen underneath appeared misty - but at least it was being protected; I planned on ordering a new one after the weekend. I did however notice one or two very clear patches. Now, some 48 hours after putting the protector on, the mistiness is totally gone and I have a perfectly clear, bubble-free screen protector on my lovely new toy. I don't need to order another screen protector after all.
Yayyy.

I had no problem getting mine on, but since it's been on it's already somehow managed to get scratched and it's peeling by the end call key as well.
Can't wait until there are some decent ones on the market.
Any known good makes to look out for?

dazultra2000 said:
I had no problem getting mine on, but since it's been on it's already somehow managed to get scratched and it's peeling by the end call key as well.
Can't wait until there are some decent ones on the market.
Any known good makes to look out for?
Click to expand...
Click to collapse
Brando do good ones, I have ordered mine.

Thanks to all for advice. I went with EXCIM (http://cgi.ebay.ie/ws/eBayISAPI.dll...K:MEWNX:IT&item=270398112761#ebayphotohosting )and it fitted easily and well, no bubbles or stange curly hairs. It's a bit thicker than the one that comes with the TP, but also a teenshy bit smaller which makes it a more forgiving fit on the device.

Another tip - use clear tape to lift the screen protector and / or dust from screen protector. Works like a charm!

Further to the sticky tape suggestion - 3M Scotch tape works the best for this

yippy following the in the bathroom (ensuite) method and a credit card applied my first ever blemish free screen protector (the standard one that came with unit) ...first go ....so thanks all concerned

lens cover damage

The see-through (plastic?) lens cover appears to have a thin layer on it, a layer that comes off easily? i can remove it with my finger nail with repeated rubbing so it can't be an anti scratch layer
It's not really like scratches it looks more like it's just being rubbed off and the surface below looks not as shiny.
Do others have this or have had this?
Anyway on mine this layer is mostly off in the middle, bit of a pisser it probably effects the photo quality..

yes, this happened to me. I got a scratch on the lens cover and the "coating" started to rub off around the scratch then. Once it's broken it will all eventually chip or rub off. I was left with a dull not so transparent lens cover. crap photos.
I got a new back cover for 30euro! (argh!!). Now I do not rub my lens and am very careful. The initial scratch was caused by a tiny piece of salt or sand on the lens when I rubbed it clean with a microfibre cloth. Once it was scratched the protective film just flaked off really easy when I rubbed it even lightly.
Get a new back cover and be very careful when rubbing the lens cover in future. In fact DON'T rub it is best. If you do get a finger print on it very very lightly use a microfibre cloth to remove it. no hard rubbing.

bummer.. i'll just leave mine i think, maybe some one will bring out a better version, or i could maybe maybe stick a plane glass disc in.

yeah, it sucks doesn't it! I would not mind paying an extra 20euro for a desire if HTC would coat the lens cover with mineral glass or something so its much less likely to scuff. plastic with a coating is useless.
anyway, good luck if you replace it with a glass disc, that would be cool too. I splashed out for the battery cover, but it was expensive and wouldn't do it again if it happens.
Thats why I loved my Nokia N82. It had an actual lens cover that kept out dust, fingerprints, grit etc.
well, HTCs next big handset release will only be improved I imagine.

Same here
I've had the same problem, bad engineering on HTC's part in my opinion as the lens(cover) is a very much exposed part of this particular phone because of its 'bulgy' design. Never had this kind of problem on my Cybershotphones.
Too bad though as I'm otherwise very happy with my Desire (although it would have been nice if the screen were a bit less prone to scratching, gief Gorillaglass).
I ended up rubbing the lenscover until the entire coating was actually rubbed off in the hope pictures would be less blurry because of the partly chipped off coating.
Anyone know what the coating is for in the first place?

if this happens to mine I will drill the clear lens out

jamesmcuk said:
if this happens to mine I will drill the clear lens out
Click to expand...
Click to collapse
I think you can just bash it out - there's a post on the forum somewhere about it

Help fixing a scratch/paint chip

I got a small scratch/paint chip on the black plastic near the usb port does anyone have any ideas on how I can fix this? I was thinking of using black nail polish.
Any other ideas would be appreciated.
Thanks!
Sent from my SAMSUNG-SGH-I897 using XDA App

Couple questions: is it on the rim of the charging port? I got one from removing my charge cable at an angle and it twisted and gouged the plastic on the way out, which leads me to my next question, is it deep? Like is it superficial or is it more like missing the gloss finish and possibly some plastic?
A usful product to have for glossy finishes is Displex, it works amazing on this phone. I am incredibly anal about high gloss finishes and blemishes showing up on them, even if i can only see them in direct sunlight. If you use this product with a cotton swab and gently but firmly rub in a circular pattern the scratches will go away very quickly, if you do it too much or too forcefully you may cause a bit of a clouding effect you can notice in strong light, so just do it for about 30 seconds and wipe it clean with a micro fiber cloth and do a little more, you should need a pea sided drop altogether, this will last for quite a while, just make sure you squeese the tube up and down to kind of mix it if it's been sitting a while. If the blemish is more of a gouge and not a fine scratch then this wont work as well, what it does is polishes the edges of the scratch down and fills in the bottom of the scratch with what's being polished smooth, so it works wonders for small problems, with larger issues you'll end up with a smooth ripple in the plastic as it will wear the hard edges down but obviously won't rebuild what's missing. I was reluctant to use it on my captivate cause it didn't do squat to my htc pure, but it performed remarkably on my captivate, just be methodical about how you use it and when you're done and your scratch is gone to your satisfaction be sure to put a little(and I mean little) on your micro fiber cloth or incredibly soft rag and buff over the area back and forth in one direction, for me that helped eliminate any cloudy effect and polish it back to a brand new phone shine. Just go into Google shopping and search for Displex, it's very inexpensive.

Sorry to repost so quickly but I forgot to mention about the nail polish, you can test it out but if it doesn't work I would be reluctant to use nail polish remover anywhere near the plastic on my captivate as it usually contains acetone which destroys plastic finishes usually, just put a drop on the surface of a cd, if it doesn't bother it you're probably ok, but I would still be reluctant. I'm a painter and have a lot of experience with solvents. The other possible issues with nail polish is it might not grip the phone well and depending on how thick it's applied might actually just pop off when it dries to be really hard. I tried it on my Fuze and it wouldn't cling to it at all; it also left a nasty seam and was just as bad of an eyesore as without it there, acrylic paints are easier to work with and dry very shiny but aren't always that hard, you'd need a type that mixes with a hardener as apposed to generic model paint, model paint takes considerable time to cure and wears down faster than the acrylic plastic of the phone.

Thanks for the advice my friend took a look at it and said its missing the gloss as the black finish came off and now there's a small white circle near the usb port.
I don't know how that happened as I always pocket the phone by itself and nothing else.
Sent from my SAMSUNG-SGH-I897 using XDA App

You may want to still try that polish I mentioned, sometimes with hard plastics like this the nick gives it a powdery look that looks worse than it is, if it's still relatively smooth but is an ugly blemish then it will most likely polish out to a high shine again and the white spot may go away. I don't know the process Samsung used for manufacturing but I was under the impression that they were solid colored plastic possibly with a protective coating over that, if I'm right then that white you mentioned should polish out. Best of luck whatever you decide to do.

[Q] Dust between bezel and glass

I read that the gap between the bezel and the glass is to help with the glass expanding due to heat, but it seems to collect dust a lot and its driving me nuts. Anyone know of a way to prevent this or a slim case that covers the gap so dust does not get in there?

i don't see a problem with my phone, mostly because the case is hiding it all LOL
and even when i do take out the case, i don't see dirt collecting there
i just go blow it off easily with a gasp of air with my mouth

Mine too!!! Have 2 white specs in top left side and don't wanna stick something in there and scratch it... Annoying thing is that my d30 case covers everything up but that little damn corner where the power button is... Ugh
Sent from my SGH-T989 using Tapatalk

I just noticed this dust accumulating in there today. Hrm.

just puff it every now and then to prevent excess accumulation and prevent it from turning into dirt

this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it

I use the body glove case from tmobile when I'm at work. My work enviroment is extremely dirty and very dusty. I mean to the point where you clean the area and by the end of the day there is a pretty thick layer of flux (lets just say dust) everywhere.
When I take my case off on the weekend my bezel is clean

dime079 said:
this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it
Click to expand...
Click to collapse
The SAMOLED screens are fused to the class so there is no gap for dust to collect.

To get rid of the dust I use a stiff lens cloth damp with lens fluid and use a corner to clean. Works perfectly
Sent from my SGH-T989 using xda premium

dime079 said:
this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it
Click to expand...
Click to collapse
dust between the bezel/screen common problem with any phone that has gap between the bezel and screen. like one person said, the digitizer is fused with the actual screen on Super Amoled screens. so dust shouldn't get underneath. However, screen repair cost more due to the fact the whole screen+digitizer has to be replaced instead of one or the other.
to get the dust out,I usually just take a very thin paper,fold it in half,and slide it. I've been doing the same method on my past phones.

Looking for some input with modding d3o & powerskin

Ok everyone this will be my first mod-accessory, for a mobile device and i am looking for some input. I want the best of both of these two cases and am pretty sure that the end result will be some kick arsenic case loved by most people. Check my video out it says all I am trying to do. http://youtu.be/DZOKjY2YMzg

Fix your audio, get prepared, get to the point and try again. Oh and gorilla glue? Couldn't tell what you wanted to use it for, but not a good idea. It expands.

Kerns_JW said:
Fix your audio, get prepared, get to the point and try again. Oh and gorilla glue? Couldn't tell what you wanted to use it for, but not a good idea. It expands.
Click to expand...
Click to collapse
I am wanting some input on how to go about using the inner top portion on the power-skin replacing the same area on the powerskin with the d3o portion. I know gorilla glue expands but nothing a razor blade can't fix after it cures.

Too many ideas, can you narrow it down?
Hard plastic kept or not?
Can hard plastic be removed if needed?
Room under the top section for an additional layer? Snug or decent room
Let's talk glue again. Wouldn't something that remains flexible be preferred?

Kerns_JW said:
Too many ideas, can you narrow it down?
Hard plastic kept or not?
Can hard plastic be removed if needed?
Room under the top section for an additional layer? Snug or decent room
Let's talk glue again. Wouldn't something that remains flexible be preferred?
Click to expand...
Click to collapse
Yeah I was thinking about losing the hard white plastic of the d3o and using the inner flexible black part. Right about the glue now that I think about it, will need some flexibility-any ideas on type of adhesive? I am thinking with the addition of the inner layer and losing the back phone coverage it will be comfortable in fit.
Sent from SGS II 4G Jelly Bean 4.1.1

okay
Cut off half of old and put on top of newer one. Issue looks dumb and unfinished. Use some type of cord to clean up the edge. Still may look bad and by removing hard plastic look nasty due to glue remains. Due to shown cracks, it's not likely you can use as hard case on top of new rubber.
Under newer one instead. Issue, it would look and feel off I think because of hump added. Maybe not sure due to hump caused by battery? Could be similar.
Fix cut old one slightly bigger than new hole. Glue edges only. Issue bump created around current lip from New hole.
Fix cut same size as new hole add inner layer such as felt. Glue piece to felt, felt to new inside part. If cut well and placed well, old piece fills void reduces lip. Issue of bad cut, looks bad. Cut slightly larger than hole and slowly trim to fit. Try to get edges to squash well together. Still may have nasty glue remains from removal of hard plastic. Fix may be tough to do and look off. Keep plastic attached, Trim both plastic and rubber to shape of hole and fit in hole. Use felt again as backer.
Eliminate felt use, trim plastic to hole, trim rubber slightly bigger. Glue old rubber to plastic and edges of old rubber to inside of new hole. Essentially, use old rubber as backer instead of felt. May still cause that hump around edge of new hole.
Fill hole with old piece as described above eliminate felt use, plastic if desired, and over size of old rubber. Create complete new back instead to glue piece to. Then glue this new back to the back of new case. This will cover up the old glue remains, bad possible cutting and lip issues. Tricky part, what to use for new back.
What's the inside of old case look like? Could it be used to create new back layer? If not sure where I am going, look at the back of a ballistic case.
Glue depends on decided application. If new back than semi rigid glue would work well. They have super glue that stays flexible. Rubber cement too flexible I think.

What would you suggest be my line of going forward? Cut the lip and buttons off the d3o
Sent from SGS II 4G Jelly Bean 4.1.1

Tough to say without being there and knowing the actual layout. Your video just made it to hard to see. Since the plastic is borked and underneath may be glued, you may want to hit up one of the mall vestibules and see if you can find some knock off cover that works to your needs.

Yeah I will probably grab some cheap cases similar & do some mock ups to get a feel for what it will be like. I'll post some pictures of my progress.
Sent from SGS II 4G Jelly Bean 4.1.1