Related
Hi,
I have an HTC Desire which is a little over a week old, though on Saturday I got my desire knocked out of my hand and took a fall onto gravel and the battery cover's camera lens cracked and now has a thick crack through the middle which is not much of a problem as it is easily replaceable, though the glass which covers the lens/sensor cracked into many pieces though I do not know if it is a filter of some sort or just some dust protector. (I can still use the camera without a problem).
Should I send it for repair to get the protector put in, or will I be ok just buying a new battery cover?
Thanks!
It's likely not just a filter of some sort, but an important part of the optical design. It could be replaceable, but normally replacing lens elements requires re-calibration of the entire lens itself. I doubt though, that they would replace just a part of the lens, they would likely swap the entire thing. I'm pretty sure HTC buy these lenses/modules already assembled and calibrated from someone who specializes in making such things.
Mac
Thanks a lot for the detailed reply! Will be sending to be repaired today. Thanks again
Hi All,
Just for everyone benefit i also cracked the back cover plastic screen and also the glass screen on the camera as well. The back cover is easily replaceable by a new back cover off eBay for £12.99 or the lens piece itself for about a £5 i think, which is easy to find but i decided to replace the internal glass myself. I found this on eBay for £7.49:
http://cgi.ebay.co.uk/ORIGINAL-HTC-...UK_Mobiles_Accessories_RL&hash=item230c703e97
Using an old sack pin i manage to remove the cracked glass, the trick is to prize up the black plastic the glass is stuck too, that way no shards fall off into the camera itself.
I thoroughly cleaned the camera and new glass with an anti-static wipe.
You have to push out gently the four plastic stripes round the camera that the glass fits into so the new glass fits it snuggly when you push it in.
I did make a hash of it to begin with and touched the back of the glass so it was smudged and got a bit of glue on it. I put an anti-static wipe on the needle end of the sack pin and cleaned it thoroughly and this did the trick. To test it though use barcode scanner as well as the camera app.
I haven't much patience and have large fingers, i guess you could take more time and use more precise tools to do a better job but as the camera isn't the most important function for me this was fine.
I did contact the HTC repair shop that was listed on XDA and this was there reply:
Hi,
You’re looking at between £39.95 and £64.95
Thanks in advance
Regards
MRC Team
www.mobilerepaircentre.com - (CLICK THIS LINK TO BOOK IN A REPAIR/REQUEST A QUOTE)
I guess if you have phone insurance that would be a better way to go but as i didn't i saved a few quid doing it myself, it only took 15 mins to do, not hard at all.
Good luck to anyone else who attempts this!
I had the same problem with my phone and I sent it away to redstafford.co.uk and I got it back in about 3 days, all new and shiny... highly recommend!
I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
Anybody know where I can get this repaired or where I can buy the part?
I'm actually quite dissapointed with the strength of the lens it cracked in my pocket like seriously shame on you HTC.
Mine did the same thing. They replaced it under the uh oh protection but I'm pissed I had to use it 2 days into owning the device.
I refuse to use my uh oh protection on it, like it doesn't effect how my pictures come out just not appealing
PhyscoAssassinx said:
I refuse to use my uh oh protection on it, like it doesn't effect how my pictures come out just not appealing
Click to expand...
Click to collapse
I had the same problem here in the UK. The retailer did exchange it for me with no fuss we don't have the uh oh protection here
PhyscoAssassinx said:
Anybody know where I can get this repaired or where I can buy the part?
I'm actually quite dissapointed with the strength of the lens it cracked in my pocket like seriously shame on you HTC.
Click to expand...
Click to collapse
How did you make out? Just happened to me... http://forum.xda-developers.com/one...mera-cover-t3073421/post60241785#post60241785
Any luck?
My M9 camera just cracked down around the middle as well :/ 2 days, no mishandling at all. Did anyone have any luck getting it fixed/replaced without using Uh-oh protection?
Sadly I haven't read anyone who's had any luck, people are just keeping it as is or getting it replaced with uh oh
Mine was replaced in store in the UK with no issues
This is disturbing. I work in construction and bang my phone on stuff while in my pocket. Thought the sapphire was an upgrade lol
Sapphire is extremely hard and resistant to scratching... But that also means it's brittle. While it's going to be extremely hard to scratch, it's going to be easier to crack.
Which is also another reason(aside from being expensive) they probably chose not to use it on the screen. (Apple as well)
so i got annoyed and just took the rest of the glass off i faced two issues, one due to the crack under certain lights i would get a glare, kinda like when you wet glass and see the rainbow colors, secondly dust got under the lens and i couldn't clean it out the pictures would look fuzzy, and lastly the cracked really F*&#!ed with the beauty of the phone....sigh so here it is, hopefully replacement parts start to pop up soon so i can put a new glass :fingers-crossed: (wheres the brickwall headbash smiley?)
I posted this in another thread but got no response. Has anyone without a case got cracked camera glass? Most seemed to have been in cases in the other thread. Maybe an issue with heat dissipation?
I don't get why they have to have such a large piece of glass with such a small lens?
We don't have Uh Oh in the UK and I don't insure so I'm really worried about this happening to mine.
ive got the same problem after 6 days no insurance and no uh oh protection, but after a bit of searching i found a replacement lens on ebay it seems too cheap to be sapphire glass but in my eyes id prefer something that wont just crack again http://www.ebay.ie/itm/New-Replacem...012?pt=LH_DefaultDomain_0&hash=item19ffc4ec3c
charlie_gti said:
ive got the same problem after 6 days no insurance and no uh oh protection, but after a bit of searching i found a replacement lens on ebay it seems too cheap to be sapphire glass but in my eyes id prefer something that wont just crack again http://www.ebay.ie/itm/New-Replacem...012?pt=LH_DefaultDomain_0&hash=item19ffc4ec3c
Click to expand...
Click to collapse
This advert seems to be for an adhesive (for the lens cover ) not the lens cover .
This company often is a useful source of smartphone spares.
They don't appear to stock many items for M9 currently, maybe range will broaden in time.
http://www.etradesupply.com/htc/android-models/htc-one-m9.html
Sent from my HTC One M9 using XDA Free mobile app
charlie_gti said:
ive got the same problem after 6 days no insurance and no uh oh protection, but after a bit of searching i found a replacement lens on ebay it seems too cheap to be sapphire glass but in my eyes id prefer something that wont just crack again http://www.ebay.ie/itm/New-Replacem...012?pt=LH_DefaultDomain_0&hash=item19ffc4ec3c
Click to expand...
Click to collapse
paul_59 said:
This advert seems to be for an adhesive (for the lens cover ) not the lens cover .
This company often is a useful source of smartphone spares.
They don't appear to stock many items for M9 currently, maybe range will broaden in time.
http://www.etradesupply.com/htc/android-models/htc-one-m9.html
Sent from my HTC One M9 using XDA Free mobile app
Click to expand...
Click to collapse
If you read the comment from the seller it says " The Lens have the film on it, Please Remove"
so it is indeed the lens and adhesive. it's typical of items from China that the translation is not very accurate.
I have ordered a few lens/adhesive kits for the M8 and they all have worked just fine, I'm sure this one is no different
Cracked glass here, too
Thanks for the eBay link. My husband and I both purchased HTC ONE M9 phones two Fridays ago. His camera lens cover glass/crystal/whatever was cracked straight across horizontally BY ITSELF after we had owned our phones for FOUR DAYS.
HTC and T-Mobile kept passing us back and forth because it was less than 14 days. HTC wanted T-Mobile to fix it, T-Mobile wanted us to use our HTC Uh Oh protection.
In the end, we are being forced to use the Uh-Oh. I'll try that eBay item first, though!
Just notice today that mine is broken also. Don't really want to use my oh uh protection just for that
Did not find a link on the whole WWW
Hello people,
My M9 lens cover cracked also, and I do not think it is because of a hit, as I tend to take care of my stuff. But it did so now I have to replace it.
Bought tools and glass from ebay, all together about £10. You can find it even cheaper. I will replace it on my own as HTC are very stupid with their policy, £30 just for diagnostic (like I do not see the glass being cracked) + repair + parts. It is overly priced.
Does anybody have a link with how to replace this glass from the M9?
If not, do you have to take the back cover off to do this?
Thank you.
Regards.
I got cracked lens cover, I have removed it awaiting New cover from eBay however without lens cover on camera does not focus on distance objects only close up. Could this be ddie to no lens cover or is the camera broken
I replaced my lens from ebay. To remove it I used a hair straitener as a hotplate to loosen the adhesive around 180 deg F
I wore rubber gloves/ and pried the sapphire off of the camera with an exacto knife and or razor blade.
Double checked to make sure I had all of potential glass shards.
I proceeded to take off the back of the new lens and lined it up and from there I now have a perfectly non-cracked lens.
Problems I ran into this. I have had a piece of dust or sand on my camera lens since I cracked it(maybe beach sand?) and always have this unfocused 1mm 'gray' spot. If I had an air compressor I would have made sure to blast my lens with it hoping to remove that spot.
I live my life with a grey spot on ALL of my photos .
But aesthetically it is barely noticeable and my lens is not cracked. I plan to use my Ut Oh protection when I get close to my date.
Seems all I can find is how to replace rear glass and lose the factory water seal.
Is there some place to purchase the back glass with the tape that goes properly around the camera and led lens?
How do you guys fix it properly?
I'm thinking silicone glue might work, but it would be very difficult to apply a thin line and hope it doesn't get on to something that will cause problem.
First... If you put silicone glue , you wont be able to take it out if you need to replace it again , or it will be very dificult.... And probably you will apply it badly and it will expand to other parts of the phone and break them ...
Second , there is a thin tape from 3M that might work but is really dificult to apply and i dont know if it protects against water
The best thing to donis replace it with normal "screen" glue and be carefull
---------- Post added at 12:47 AM ---------- Previous post was at 12:44 AM ----------
In amazon you can find that tape from 3M double face with just 1mm from 7€
Thank you for the comment. I was thinking the same but the thing is when you put the tape around the camera and LED lens, there is going to be a seam which could let water through. But I guess I could just drop a tiny drop of glue on to the seam.? I need to search for "screen glue" now. Any suggestions?
The reason I'm doing the repair is not because of looks, but because I want the phone to be water resistant again like factory.
(I just bought the phone and ordered the case to arrive the next day. As I'm waiting the next day, it falls out of my pocket while trying to get inside a car. Being about 2 feet off the ground. I'm very surprised how weak the glass is because it hit the frame first and cracked the corner.)
I spent a total of 3 hours. Not only searching for Pixel but also Samsung Galaxy and everybody that does the repair ends up doing it by destroying the phones water resistant feature. I have not found one tutorial or video on YouTube that somebody fixes the phone the factory way so it retains the water resistance or waterproof, whatever you want to call it.
turbogodzilla said:
Thank you for the comment. I was thinking the same but the thing is when you put the tape around the camera and LED lens, there is going to be a seam which could let water through. But I guess I could just drop a tiny drop of glue on to the seam.? I need to search for "screen glue" now. Any suggestions?
The reason I'm doing the repair is not because of looks, but because I want the phone to be water resistant again like factory.
(I just bought the phone and ordered the case to arrive the next day. As I'm waiting the next day, it falls out of my pocket while trying to get inside a car. Being about 2 feet off the ground. I'm very surprised how weak the glass is because it hit the frame first and cracked the corner.)
I spent a total of 3 hours. Not only searching for Pixel but also Samsung Galaxy and everybody that does the repair ends up doing it by destroying the phones water resistant feature. I have not found one tutorial or video on YouTube that somebody fixes the phone the factory way so it retains the water resistance or waterproof, whatever you want to call it.
Click to expand...
Click to collapse
You can also search for a screen that comes with the original sticker (tape) ... That might work
The problem with the rear replacement glass is that the only adhesive is around the glass and nothing around the camera and LED lens.